Allowable Deviation Research Articles

A radar array expansion design method based on modular subarray layout

Abstract This paper introduces a design method for expandable subarray structures used in phased array radar arrays. Based on the structural characteristics of modular subarray layout for large radar arrays, this paper analyzes the assembly dimension chain tolerance based on subarray expansion. One third of the allowable deviation of the radar array is used as the subarray design tolerance, and the size tolerance of each installation surface of the subarray is designed according to the design tolerance. Finally, the subarray array is assembled into any size of radar array, and the probability of the radar array assembly accuracy meeting the allowable deviation is 99.73%. For large radar arrays, adopting this design method can significantly reduce the tolerance span between the sub array and the area array, greatly reducing the difficulty of design and processing. This paper provides a fundamental design method for the expansion design of radar arrays with similar systems, which has universal applicability.

Requirements for partial turbulence simulations using nondimensional turbulence energy contributions

Quantifying turbulence effects is crucial for understanding building aerodynamics and for ensuring accurate wind tunnel test methods. This is especially important in wind tunnel methods that require post-experiment adjustments because approximate wind fields are used, such as the Partial Turbulence Simulation (PTS) approach. Understanding and analyzing these effects enables load adjustments since the PTS method only requires matching the high frequency portions of the upstream spectra of the longitudinal velocity component in model and full-scale. However, the limits for which the PTS method is applicable are unclear in terms of the allowable range of wind field characteristics that can be used in the wind tunnel simulation. To address this, the paper utilizes two nondimensional parameters, one representing the small-scale turbulence energy, ES, and the other the large-scale turbulence energy, EL, to elaborate the aerodynamic effects of turbulence intensity and integral length scales in the upstream wind. The results show that the maximum allowable mismatch ratio of integral length scales and of Jensen numbers between model and full-scale simulations depend on the target small-scale turbulence energy and the maximum allowable deviation of small-scale energy. By quantifying the effects of ES and EL on area-averaged pressure coefficients, the allowable limits are identified for wind tunnel test parameters that lead to negligible differences in the resultant pressure coefficient statistics in regions of separated-reattaching flow on the roof of a low-rise building.

Validation of combiomed hipermax-BF model A7101 automatic oscillometric upper-arm sphygmomanometer in general population: AAMI/ESH/ISO universal standard (ISO 81060-2:2018/Amd 1:2020).

This study evaluates the accuracy of the Hipermax-BF model A7101 (Combiomed, Havana, Cuba) automatic oscillometric upper-arm sphygmomanometer for office and home use in general population as part of the HEARTS in the Americas initiative. The research was developed according to the Universal Standard AAMI/ESH/ISO ISO 81060-2:2018/Amd 1:2020. The subjects were recruited according to the requirements of age, gender, blood pressure values and upper-arm circumference. The same upper-arm sequential blood pressure measurement method was used. For measurements with the device under test, the 2-piece cuff from 22-44 cm limb circumference range was used. 92 subjects were recruited and 85 were analyzed. Mean age was 44.8 ± 14.7 years, mean upper-arm circumference was 32.3 ± 6.2, and 56.5% were female. For Validation Criterion 1, the mean value ± standard deviation of the differences in readings between the device under test and the reference device was 1.2 ± 4.9/0.8 ± 4.9 mmHg (systolic/diastolic). For both pressures, in criterion 1 the standard requires a mean value of the differences ≤ ± 5 mmHg and a standard deviation ≤ ± 8 mmHg. For Validation Criterion 2, the standard deviation of the mean blood pressure differences per subject was 4.2/4.2 mmHg (systolic/diastolic). According to Table 1 of criterion 2, for the mean values of 1.2/0.8 mmHg (systolic/diastolic), the maximum allowable standard deviation had to be < 6.84 for systolic and < 6.89 for diastolic pressure. The Combiomed Hipermax-BF A7101 automatic sphygmomanometer meets the requirements of the AAMI/ESH/ISO Universal Standard (ISO 81060-2:2018/Amd 1:2020) in the general population.

Underwater fluid-driven soft dock for dynamic recovery of AUVs with improved pose tolerance

Recovering autonomous underwater vehicles (AUVs) by a mobile platform is a complex challenge. Traditional docking stations require strict pose deviation from the underwater vehicle. To overcome this issue, we propose a novel solution: an in-situ fluid-driven soft dock. This system comprises three soft robotic manipulators that possess guiding, capturing, and securing functionalities, respectively. We present the design, fabrication, and control methods for each manipulator considering the requirements of underwater docking operations. The theoretically allowable docking pose deviation range during AUV docking is analyzed. Additionally, the required force of soft grippers was evaluated through simulation and equivalent experimental tests. To enable dynamic recovery of AUVs while the soft robotic manipulators remain mobile on the experimental platform, we introduce a hydraulic control method based on attitude and pressure feedback. The test results indicate that the designed soft manipulators can operate and maintain good sealing performance under an external pressure of no less than 11 MPa. Moreover, the soft dock successfully recovered and secured AUVs of two different diameters in 20 dynamic tests, achieving a 90% success rate with a maximum AUV velocity of 1.6 m/s.

An Analysis of Drilling Projection Uncertainty and Implications for Collision Avoidance Management Systems

Summary During well planning, specifying the separation that must be maintained from offset wellbores is critical to ensuring safe operations. Recent efforts on API RP 78, an upcoming American Petroleum Institute recommended practice for wellbore placement, have provided guidelines for calculating safe separation distances and engineering considerations for those calculations. A major milestone was the publication of a separation rule (Sawaryn et al. 2019) standardizing a formula for separation factor (SF), which in turn defines the minimum allowable separation distance (MASD) between two wellbores and the allowable deviation from plan (ADP) for a wellbore being drilled. One element of this formula, σpa, describes the accuracy with which a future wellpath can be predicted. Prior guidance provides a suggested value for σpa (1.6 ft or 0.5 m at 1-sigma) based on heuristics. A more rigorous approach for estimating this value is presented, where the design of the drilling program can be considered. A framework is proposed for modeling deviation from a projected path using a planned trajectory, bottomhole assembly (BHA) properties, and survey practices. The method identifies where a deviation is detected through survey measurements and estimates a planned recovery operation. Equations are provided for estimating the distance from plan at deviation detection along with the maximum expected deviation during recovery. Common drilling scenarios are analyzed for sensitivity to operational parameters such as survey course length, sensor offset, tool face control, and BHA performance. The impact of varying σpa is explored across prototypical collision avoidance cases. A discussion of the relationships between the σpa value and the common collision avoidance calculations, such as SF, MASD, and ADP, is included along with considerations for the design of a risk management policy. Survey course length, survey sensor offset, and uncertainty in directional performance are all shown to have a significant impact on the potential maximum deviation from plan. An additional factor considered is the aggressiveness expected when performing recovery operations. An analysis of common drilling scenarios suggests the previously provided guidance of 1.6 ft at 1-sigma appears suitable for cases where the directional behavior of the BHA is well characterized and the combination of course length and survey sensor offset is kept to 150 ft or less. Longer survey course lengths, larger sensor offsets, or uncertainty in directional performance of the BHA can produce larger σpa values, in some scenarios causing a significant impact on the MASD and ADP. Previous work has called attention to the uncertainty in drilling to a projection, but up to now, there has not been a rigorous method for estimating that quantity. With the methods outlined in this paper, well planners and drilling engineers can make more informed decisions on how to ensure safe separation practices in their own operations.

The Multiobjective Control Based on Tolerance Optimization in a Multienergy System

To address the issue of multiobjective control in multienergy systems with diverse operational objectives, a two-stage optimization framework based on expected point tolerance has been proposed in this paper. In the first stage, a single objective function is used for optimization control to obtain the expected point of the multiobjective optimization problem. Then, in the second stage, by defining the allowable deviation between each optimization objective and the expected point, the original multiobjective optimization problem is transformed into a single objective optimization problem solution with tolerance measurement. Finally, in the simulation scene of a multienergy system, it is demonstrated that compared with the optimal results under each single objective method, the proposed method increases power line loss, maximum voltage deviation, new energy consumption, and economy by 2.22, 2.30, 1.02, and 2.45 times, respectively. Compared with the suboptimal results, the proposed method reduces power line loss by 22.26, 1.74, 1.09, and 0.97 times, respectively. Combining the shape of the Pareto frontier, it is demonstrated that the proposed method can comprehensively consider the needs of multiple power optimization objectives for forming a more reasonable and effective system optimization scheduling and also provide a new approach for solving multiobjective optimization problems.

ACR benchmark testing of a novel high-speed ring-gantry linac kV-CBCT system.

A new generation cone-beam computed tomography (CBCT) system with new hardware design and advanced image reconstruction algorithms is available for radiation treatment simulation or adaptive radiotherapy (HyperSight CBCT imaging solution, Varian Medical Systems-a Siemens Healthineers company). This study assesses the CBCT image quality metrics using the criteria routinely used for diagnostic CT scanner accreditation as a first step towards the future use of HyperSight CBCT images for treatment planning and target/organ delineations. Image performance was evaluated using American College of Radiology (ACR) Program accreditation phantom tests for diagnostic computed tomography systems (CTs) and compared HyperSight images with a standard treatment planning diagnostic CT scanner (Siemens SOMATOM Edge) and with existing CBCT systems (Varian TrueBeam version 2.7 and Varian Halcyon version 2.0). Image quality performance for all Varian HyperSight CBCT vendor-provided imaging protocols were assessed using ACR head and body ring CT phantoms, then compared to existing imaging modalities. Image quality analysis metrics included contrast-to-noise (CNR), spatial resolution, Hounsfield number (HU) accuracy, image scaling, and uniformity. All image quality assessments were made following the recommendations and passing criteria provided by the ACR. The Varian HyperSight CBCT imaging system demonstrated excellent image quality, with the majority of vendor-provided imaging protocols capable of passing all ACR CT accreditation standards. Nearly all (8/11) vendor-provided protocols passed ACR criteria using the ACR head phantom, with the Abdomen Large, Pelvis Large, and H&N vendor-provided protocols produced HU uniformity values slightly exceeding passing criteria but remained within the allowable minor deviation levels (5-7 HU maximum differences). Compared to other existing CT and CBCT imaging modalities, both HyperSight Head and Pelvis imaging protocols matched the performance of the SOMATOM CT scanner, and both the HyperSight and SOMATOM CT substantially surpassed the performance of the Halcyon 2.0 and TrueBeam version 2.7 systems. Varian HyperSight CBCT imaging system could pass almost all tests for all vendor-provided protocols using ACR accreditation criteria, with image quality similar to those produced by diagnostic CT scanners and significantly better than existing linac-based CBCT imaging systems.

Implantation Corridors in Canine Thoracic Vertebrae: A Morphometric Study in Dogs of Varying Sizes.

Surgical stabilization to treat fractures, luxations, and congenital malformations in the thoracic spine can be difficult due to its unique anatomy and surrounding structures. Our objective was to document the morphometrics of the thoracic vertebrae relating to an ideal trajectory for dorsolateral implant placement in a variety of dog sizes and to assess proximity to important adjacent critical anatomical structures using computed tomography (CT) studies. Medical records for 30 dogs with thoracic CT were evaluated. Implantation corridor parameters for thoracic vertebrae (T1-T13) were measured, including the length, width, angle from midline, and allowable deviation angle for corridors simulated using an ideal implant trajectory. The distances from each vertebra to the trachea, lungs, aorta, subclavian artery, and azygos vein were also measured. Implantation corridor widths were often very narrow, particularly in the mid-thoracic region, and allowable deviation angles were frequently small. Distances to critical anatomical structures were often less than 1 mm, even in larger dogs. Thoracic implantation requires substantial precision to avoid breaching the canal, ineffective implant placement, and potential life-threatening complications resulting from invasion of surrounding anatomical structures.

Comparative analysis of deviation in high buildings based on earthquake load SNI 1726:2012 and SNI 1726:2019

In 2019 the National Standardization Agency (BSN) issued the latest Indonesian National Standard (SNI), namely SNI 1726:2019 concerning Procedures for Planning Earthquake Resistance for Building Structures and No Buildings. SNI 1726:2019 is a revision of SNI 1726:2012. The purpose of this study was to determine the percentage of displacement ratio in tall buildings between using SNI for Planning Procedures for Earthquake Resistance for Building Structures and Building Structures SNI 1726:2012 and SNI 1726:2019. The method used in this research is data analysis using numerical methods. Data analysis by analyzing steel building structures and modeling steel building designs using SAP2000. The results of the analysis show that the comparison of drift between floors in buildings using SNI 2012 and SNI 2019 is not very significant and is still within the allowable deviation limits.

Compressive Strength Endorsement with Regression Props of Inflection and Tolerance for Material Substituted Self Compacting Concrete with Fiber Reinforcement

This research comprises Self-Compacting Concrete (SCC) and Polypropylene fibers to enhance its mechanical properties, tensile strength and crack resistance. Self-Compacting Concrete (SCC) has gained significant attention in the construction industry due to its ability to flow and fill intricate forms without the need for external compaction. The use of different materials as substitutes in SCC with Polypropylene fiber reinforcement poses challenges in determining the compressive strength, as the properties of the substituted materials can vary significantly. This study focuses on developing a comprehensive approach for endorsing the compressive strength of fiber-reinforced SCC with material substitution. Regression analysis techniques are engaged to establish a mathematical model that correlates the compressive strength with key influencing factors. The study identifies two critical properties: inflection and tolerance, which significantly affect the compressive strength of the substituted SCC. This study determined through considering different combinations of substitution materials and their respective proportions. It takes into account the potential variations in the physical and chemical characteristics of substitute materials. The optimum limit is defined, which indicates the maximum allowable deviation without compromising the compressive strength. The developed model is validated through an extensive experimental test, involving a range of substitution materials, fiber types and proportions. The results demonstrate the accuracy and effectiveness of the proposed approach in predicting the compressive strength of fiber-reinforced SCC with fly ash substitution. This study gives the advancement of SCC technology by providing a comprehensive framework for validating the compressive strength of fiber-reinforced SCC with material substitution.

GENERAL PRINCIPLES OF FORECASTING THE RELIABILITY OF COMPLEX TECHNICAL SYSTEMS IN THE OIL AND GAS INDUSTRY

In the oil and gas industry, various high-risk facilities operate, among which pipeline systems occupy a leading position due to their specific characteristics (structural, technological, operational conditions, etc.).&#x0D; Pipeline systems, distributed over a large area, are characterized by a high level of risk of emergencies. Therefore, the risk analysis of accidents and failures, the main essence of which is to identify hazards and assess the possibility of their occurrence, is a crucial part of the industrial safety management system of technical systems (TS) [1]. One of the main tasks of this system is to prevent the possibility of accidents and failures, i.e., to ensure reliability. The authors emphasize the importance of assessing the reliability of high-risk objects, both when put into operation and during their operation. It is noted that reliability management during the operation stage can be carried out by determining the optimal allowable deviations of structural parameters of the technical condition and other measures. The paper provides an overview of key quantitative reliability indicators, such as the reliability function and the "unreliability function," and discusses their significance in determining failure probabilities and life-to-failure. Changes in failure intensity according to the Weibull distribution and the exponential distribution law are examined in detail. Reliability indicators for non-repairable systems include the probability of non-failure operation, failure intensity, and mean time to failure, while maintainability indicators for repairable systems are the probability of recovery and mean recovery time. The comprehensive indicator of the reliability of repairable systems is determined through the coefficient of operational readiness. The conclusions of the paper highlight the importance of using statistical data and reliability indicators to assess systems and components, in particular the oil and gas pipeline systems in Europe, which have significant importance for industrial safety and the reliability of technical facilities.

Tracking-dispatch of a combined wind-storage system based on model predictive control and two-layer fuzzy control strategy

To maximize improving the tracking wind power output plan and the service life of energy storage systems (ESS), a control strategy is proposed for ESS to track wind power planning output based on model prediction and two-layer fuzzy control. First, based on model predictive control, a model with deviations of grid-connected power from the planned output and the minimum deviation of the remaining capacity of the ESS from the ideal value is established as the target. Then, when the grid-connected power exceeds the allowable deviation band of tracking, the weight coefficients in the objective function are adjusted by introducing the first layer of fuzzy control rules, combining the state of charge (SOC) of the ESS with the dynamic tracking demand of the planned value of wind power. When the grid-connected power is within the tracking allowable deviation band, the second layer of fuzzy control rules is used to correct the charging and discharging power of the ESS to improve its ability to track the future planned deviation while not crossing the limit. By repeatedly correcting the charging and discharging power of the ESS, its safe operation and the multitasking execution of the wind power plan output tracking target are ensured. Finally, taking actual data from a wind farm as an example, tests on a simulation platform of a combined wind-storage power generation system verify the feasibility and superiority of the proposed control strategy.

Enhancing Dental Applications: A Novel Approach for Incorporating Bioactive Substances into Textile Threads.

In the realm of surgical and dental applications, hyaluronic acid (HA) braided threads show significant therapeutic potential due to their incorporation of pharmaceutical active ingredients. This study primarily focuses on resolving the crucial challenge of devising a deposition method that can ensure both precision and uniformity in the content of the active ingredient Octenidine dihydrochloride (OCT) within each segment of the threads. Our objective in this study was to develop a continuous deposition method for OCT onto a braided thread composed of 24 hyaluronic acid-based fibers, aiming for a specific OCT content of 0.125 µg/mm, while maintaining a maximum allowable deviation of ±15% in OCT content. The motivation behind designing this novel method stemmed from the necessity of employing a volatile solvent for the active agent. Conventional wetting methods proved unsuitable due to fluctuations in the solution's concentration during deposition, and alternative methods known to us demanded intricate technical implementations. The newly introduced method offers distinct advantages, including its online processing speed, scalability potential, and cost-efficiency of the active agent solution. Additionally, it minimizes the impact on the natural polymer thread, preserving energy by obviating the need for complete thread saturation. Our research and precise apparatus development resulted in achieving the desired thread properties, with an OCT content of (1.51 ± 0.09) µg per 12 mm thread piece. These findings not only validate the suitability of this innovative method for depositing active agents but also extend its potential applicability beyond dental care.

B-281 Analytical Validation of the Mindray High Sensitivity Cardiac Troponin I Assay

Abstract Background According to recent global guidelines for patients presenting with ischemia, high sensitivity cardiac troponin I and T (hs-cTn) are the preferred biomarkers for the diagnosis and risk assessment of acute myocardial infarction (MI) and myocardial injury. The purpose of our study was to perform an analytical validation study of the Mindray hs-cTnI assay. Methods Analytical studies were designed according to Clinical and Laboratory Standards Institute protocols (CLSI). We used one reagent lot and one CL1200i chemiluminescence Immunoassay Analyzer (Mindray Bio Medical Electronics Co., Shenzhen, China). Following the CLSI EP17 A2 document, the limit of blank (LoB) and limit of detection (LoD) were assessed following analysis of a) Mindray controls without cTnI concentrations added for the LoB and b) 4 lithium heparin (LiHep) fresh samples with low cTnI concentrations, for 3 days for LoB and LoD, with 5 replicates per day (60 replicates per study). For the precision study, according to the CLSI EP15-A3 protocol, we used 12 LiHep fresh samples, measured for 10 days, with 2 runs per day (separated by a minimal time of 2 h) and in replicates of 3 (n = 720). For the 12 samples for the precision study, 7 were chosen with hs-cTnI concentrations close to the manufacturer sex-specific 99th percentile upper reference limits (URL; 31 ng/L for males and 15 ng/L for females). The CLSI EP06 protocol was followed to study linearity, using 9 fresh LiHep samples analyzed the same day in replicates of 7 (n = 63). A blank sample between every sample was used to avoid carryover. Our analytical specification for linearity was an allowable deviation &amp;lt;10%. Analyses were performed with Analyze it for Excel (Method Validation edition, version 6.15). Results Using both parametrical and non-parametrical analyses, LoB was &amp;lt;0.1 ng/L, with a relative light unit (RLU) of 5394. LoD was 0.1 ng/L according to the parametrical analysis. Regarding imprecision, for samples ranging from cTnI concentrations of 1 to 106 ng/L, repeatability had a coefficient of variation (%CV) from 1.15% to 3.83%, and within-laboratory imprecision ranging from 1.69% to 5.03%. Using samples with hs-cTnI concentrations close to the manufacture’s sex-specific upper reference limits (9–36 ng/L), the repeatability and within-laboratory precision was 1.27%–1.61% and 1.92%–2.52%, respectively. The measuring interval for the linearity study ranged from 1.1 to 30 772 ng/L. All analytical parameters met CLSI limits of acceptable performance. No carry over was detected. Conclusion Our analytical observations of the Mindray hs-cTnI assay demonstrate excellent LoB, LoD, imprecision and linearity, that were in alignment of with the manufacturer’s claims and published guidelines for hs-cTnI.

Effluent Quality-Aware Event-Triggered Model Predictive Control for Wastewater Treatment Plants

Wastewater treatment plants (WWTPs) are large-scale and nonlinear processes with tightly integrated operating units. The application of online optimization-based control strategies, such as model predictive control (MPC), to WWTPs generally faces high computational complexity. This paper proposes an event-triggered approach to address this issue. The model predictive controller updates information and solves the optimization problem only when the corresponding triggered logic is satisfied. The triggered logic sets the maximum allowable deviation for the tracking variables. Moreover, to ensure system performance, the design of the event-triggered logic incorporates the effluent quality. By obtaining the optimal sequence for the effluent quality within the receding horizon of the MPC, the cumulative deviation between the predicted and desired effluent quality is analyzed to evaluate the performance within that horizon. Based on these two conditions, the need for adjusting control actions is determined. Even if the maximum allowable range for the tracking variables in the triggered logic design is set unreasonably, the consideration of effluent quality factors in the triggered conditions ensures good performance. Simulation results demonstrate an average reduction in computational effort of 25.49% under different weather conditions while simultaneously ensuring minimal impact on the effluent quality and total cost index and compliance with effluent discharge regulations. Furthermore, this method can be combined with other approaches to guarantee effluent quality while further reducing computation time and complexity.

Handling polypharmacy –a qualitative study using focus group interviews with older patients, their relatives, and healthcare professionals

BackgroundOn average, older patients use five or more medications daily. A consequence is an increased risk of adverse drug reactions, interactions, or medication errors. Therefore, it is important to understand the challenges experienced by the patients, relatives, and healthcare professionals pertinent to the concomitant use of many drugs.MethodsWe conducted a qualitative study using focus group interviews to collect information from patients, relatives, and healthcare professionals regarding older patients’ management of prescribed medicine. We interviewed seven patients using five or more medications daily, three relatives, three general practitioners, nine nurses from different healthcare sectors, one home care assistant, two hospital physicians, and four pharmacists.ResultsThe following themes were identified: (1) Unintentional non-adherence, (2) Intentional non-adherence, (3) Generic substitution, (4) Medication lists, (5) Timing and medication schedule, (6) Medication reviews and (7) Dose dispensing/pill organizers.ConclusionMedication is the subject of concern among patients and relatives. They become confused and insecure about information from different actors and the package leaflets. Therefore, patients often request a thorough medication review to provide an overview, knowledge of possible side effects and interactions, and a clarification of the medication’s timing. In addition, patients, relatives and nurses all request an indication of when medicine should be taken, including allowable deviations from this timing. Therefore, prescribing physicians should prioritize communicating information regarding these matters when prescribing.

Finite-Time Stochastic Synchronization of Multiweighted Directed Complex Networks via Intermittent Control

In this paper, finite-time synchronization (FTS) is addressed for directed multiweighted complex networks (MWCNs) with stochastic perturbations via intermittent control. Different from the previous FTS of single-weight networks, FTS of directed MWCNs is considered by introducing the allowable deviation synchronization bound. In synchronization analysis, a novel Lyapunov function is constructed by selecting a vector where the Chebyshev distance between this vector and their corresponding vectors for coupling matrices satisfies the allowable deviation synchronization bound. Furthermore, continuous control is not realistic due to limited resources. Accordingly, by discontinuous intermittent control, some suitable criteria can be derived to achieve FTS of directed MWCNs with stochastic perturbations. Finally, examples show the validity of the provided theoretical results.

Home Made Four-Point Probe: Case Studies of the Wobbly A and B Probes

A simulation on the effect of probe deviation on sheet resistivity value (Rs) of Cu/Ni thin film was carried out in a home-made four-point probe (HM-FPP) type. This began by solving the Rs formula for normal probes, and then for wobbly probe when it was either A, or both A and B. The formula was implemented on a thin layer of Cu/Ni, which was a low temperature sensor material obtained from electrodeposition for 60s assisted by a 200G magnetic field at a current density of 0.07A/mm2. An electric current of 0.20118A was flown from probe A to D in order to produce a potential difference between probe C and D of 0.0005 volts. Furthermore, the distance between the probes was 5 mm and the deviation of each probe A and B were simulated from -0.5 mm to 0.5 mm. The maximum allowable limit for the relative error of Rs or SRs is 5%. The results showed that the ideal Rs value was 0.113 ohm/sq. Furthermore, for HM-FPP in which the wobbly probe only A, there is no problem encountered with the variation of the deviation because all SRs are less than 5%. For wobbly probes A and B, if they are on the same side of the center point of each probe, the maximum allowable deviation is 0.3 mm. The SRs for this case were 4.6%. However, if they are on different sides of the center point of each probe, the maximum allowable deviation is 0.1 mm with SRs of 2.9%. With these results, HM-FPP craftsmen must be more careful in making the size of the probe hole.

Study on the Systematic Design of a Passive Balancing Algorithm Applying Variable Voltage Deviation

A balancing circuit in a multi-series battery pack prevents a specific cell from being overcharged by reducing the voltage difference between the cells. Passive cell balancing is widely used for easy implementation and volume and size reduction. For optimal passive cell balancing, the charging/discharging current conditions and the state of charge (voltage condition) of the battery must be determined. In addition, the balancing algorithm must determine an allowable voltage deviation threshold between the cells connected in series to determine whether a specific cell performs a balancing operation. However, previous studies have not dealt with the design of balancing operating conditions in detail. In addition, the balancing time and efficiency improvement effect under specific conditions for arbitrary battery cells used in each previous study were mainly presented. Therefore, this study proposes a variable voltage deviation method in which the threshold for determining the voltage to be balanced is changed by reflecting the battery capacity, rated current specification, open-circuit voltage, and resistance of the balancing circuit. In addition, the voltage management performance and efficiency analysis results of the existing balancing algorithm and the proposed balancing method for the case where there is parameter deviation in the cells of the battery pack are also presented. The proposed method was verified through the simulation and experimental results of a reduced battery module in which three types of battery cells, INR 18650-30Q, INR 18650-29E, and INR 21700-50E, were arranged in 4-series.

Synchronization and Control for Multiweighted and Directed Complex Networks.

The study of complex networks with multiweights (CNMWs) has been a hot topic recently. For a network with a single weight, previous studies have shown that they can promote synchronization, but for CNMWs, there are no rigorous analyses about the role of coupling matrices. In this brief, the complex network is allowed to be directed, which is the main difference with previous studies and may make the synchronization analysis difficult for multiple couplings. At first, we prove that if the inner coupling matrices are all diagonal, then synchronization can be realized only if the weighted sum (or union) of multiple coupling matrices is strongly connected, which bridges the gap between single-weighted and multiweighted networks. Moreover, we also consider the case that inner coupling matrices are positive definite but not diagonal. We design two techniques for this hard problem. One technique is to decompose inner coupling matrices into diagonal matrices and residual matrices. The other one is to measure the similarity between outer coupling matrices. In virtue of the normalized left eigenvectors (NLEVecs) corresponding to the zero eigenvalue of coupling matrices, we prove that if the Chebyshev distance between NLEVec is less than some value, defined as the allowable deviation bound, then the synchronization and control will be realized with sufficiently large coupling strengths. Furthermore, adaptive rules are also designed for coupling strength.