Airborne-particle Abrasion Research Articles

Effect of different surface treatments on retention and fracture strength of zirconia crowns over Ti-base zirconia abutments

BackgroundLimited evidence suggested different outcomes of surface treatment methods on zirconia abutments and crowns. Therefore, we investigated the effect of grooving, hot etching, and airborne particle abrasion (APA) methods on zirconia crowns over Ti-base zirconia abutments retention and fracture strength. Materials and methodsIn this in vitro study, 110 zirconia crowns and abutments were divided into five groups, including APA for crown and grooved zirconia abutment (APACr-GrAb), APA for crown and hot etching zirconia abutment (APACr-HtAb), grooved modified zirconia crown and APA for zirconia abutments (GrCr-APAAb), hot etching modified zirconia crown and APA for zirconia abutments (HtCr-APAAb), and APA for both crown and zirconia abutments (control group). The retention and fracture strength were measured. Data were analyzed by ANOVA, Tukey, Kruskal-Wallis, and Mann-Whitney with Bonferroni correction tests (α=0.05). ResultsHot etching and grooving on the crown or abutment significantly resulted in higher retention (P<0.001). The fracture strength significantly differed among the five groups (P=0.041), with the highest fracture strength observed in the GrCr-APAAb group and the lowest for the APACr-GrAb group; however, no significant differences were found in pairwise comparisons between groups (P>0.05). By considering both fracture strength and retention, grooving, hot etching, and APA were confirmed for better crown and abutment function, respectively. ConclusionGrooving surface treatment was the best method due to its high fracture strength and retention, followed by hot etching due to its high retention compared to APA, which can be considered a suitable method for cementing zirconia crown on zirconia abutments.

Effect of mechanical and chemical surface treatments on the repairing of milled and 3D-printed denture bases.

Ensuring a strong bond between chairside autopolymerized acrylic resin to denture base is essential for denture repair and reline procedures. However, there is no established protocol to enhance bond strength between autopolymerizing resin and computer-aided design and computer-aided manufacturing (CAD-CAM) denture base materials. The purpose of this study was to determine shear bond strength of CAD-CAM denture bases and autopolymerizing acrylic resin after mechanical and chemical surface treatments compared with heat-polymerized acrylic resin. Heat-polymerized, milled, and 3-dimensional (3D) printed denture bases were divided into 4 surface treatment protocols: none (control), airborne-particle abrasion (APA), tetrahydrofuran, and Vitacoll application. Autopolymerizing acrylic resin cylinders were bonded to denture surface. Shear bond strength and failure modes were determined after thermocycling. Denture base surfaces were assessed for surface roughness, surface morphology, and microhardness before and after surface treatment. Data was analyzed using two-way ANOVA and multiple comparison tests. The results showed that APA significantly increased shear bond strength and surface roughness of all denture base materials. Tetrahydrofuran and Vitacoll application improved shear bond strength of heat-polymerized acrylic resin, but did not reach the level achieved by APA. Conversely, tetrahydrofuran application improved bond strength of 3D-printed denture to the level of APA. Tetrahydrofuran and Vitacoll application significantly reduced denture base hardness, compared with control and APA. In conclusion, mechanical surface treatment using APA enhances the adhesion of autopolymerizing acrylic resin to heat-polymerized and CAD-CAM denture bases. Tetrahydrofuran and Vitacoll chemical surface treatment improved adhesion to heat-polymerized acrylic resin, with only tetrahydrofuran enhancing bond strength of 3D-printed denture to the level of APA. Without surface treatment, the highest bond strength was shown in 3D-printed denture base material.

The effects of optimized microstructured surfaces on bond strength and durability of NPJ-printed zirconia

ObjectivesThis study was to investigate the effects of optimized microstructured surfaces on bond strength and bond durability of the latest nanoparticle jetting (NPJ)-printed zirconia. MethodsZirconia microstructured surfaces with different geometries and void volume were analyzed through three-dimensional finite element analysis for surface micromorphology optimization. Zirconia disks and cylinders were additively manufactured by an NPJ 3D printer (N = 128). They were randomly divided into four groups based on surface micromorphology optimization and airborne-particle abrasion (APA) treatment before they were bonded using 10-methacryloloxydecyl dihydrogen phosphate (MDP) containing resin cement (Clearfil SA luting cement). The shear bond strengths (SBSs) were tested before and after 10,000 thermocycles and were analyzed by one-way ANOVA analysis. Failure modes were determined by optical microscopy. Zirconia surfaces were analyzed with X-ray diffraction, scanning electron microscopy, and three-dimensional interference microscopy. ResultsThe optimized microstructured surface was characterized by circular microstructures with 60 % void volume, about 20 µm of depths, about 10 µm of undercuts, and consistent beam widths. The optimized microstructured surface combined with APA treatment and MDP-containing resin cement possessed the highest SBSs both before and after thermocycling aging (P＜0.05). The greater reductions of zirconia bond strengths occurred when the zirconia were not treated with APA (P＜0.05). SignificanceThe optimized microstructured zirconia surface with circular microstructures and 60 % void volume fabricated by the latest NPJ printing technology could greatly enhance the zirconia bond strength and durability in combination with APA treatment and application of MDP-containing resin cement, which might be promising for adhesively bonded indirect restorations of NPJ-printed zirconia.

Effect of Surface Treatment with Zirconium Dioxide Slurry on the Bond Strength of Resin Cement to Ultratranslucent Zirconia.

This laboratory study aimed to evaluate the effects of zirconium dioxide (ZrO2) slurry surface treatment on the bond strength of ultratranslucent zirconia to resin cement using different ceramic primers. The surface morphology was evaluated by scanning electron microscopy (SEM) and atomic force microscopy (AFM), and the interface was evaluated by SEM. Additionally, the phase composition was analyzed by X-ray diffraction (XRD). Specimens of zirconia (n=120) were obtained and divided into two groups according to the surface treatment: (1) airborne particle abrasion with 50-μm aluminum oxide (n=60) and (2) ZrO2 slurry (n=60). The 60 specimens were then further divided into three groups (n=20) according to the ceramic primer application: no primer (NP), Monobond N (MB), and Clearfil ceramic primer (CP). Four resin cement cylinders were built on each ceramic specimen. Half of the specimens (n=10) were subjected to a microshear bond strength (μSBS) test after 24 hours of storage in distilled water, and the other half (n=10) were subjected to a μSBS test after thermocycling. Additional specimens were prepared for SEM, AFM, and XRD analyses. According to the Kruskal-Wallis and Student-Newman-Keuls post hoc tests, the μSBS values were significantly higher for MB and CP than for NP (p<0.05), and there were no significant differences in μSBS for both surface treatments associated with MB and CP after 24 hours of storage (p>0.05). Thermocycling significantly decreased the μSBS values for all specimens, especially for the NP groups and ZrO2 slurry treatment groups, and gaps at the interface were observed by SEM. SEM and AFM analyses showed agglomerate-type irregularities on the ceramic surface for ZrO2 slurry treatment. XRD spectra showed that ZrO2 slurry did not cause phase transformation. It was concluded that ZrO2 slurry promoted irregularities on the ultratranslucent zirconia surface, not causing phase transformation; moreover, the values of μSBS were comparable to those of airborne particle abrasion with aluminum oxide. However, neither surface treatment nor ceramic primer prevented the degradation of the interface.

Effect of adhesives and mechanical surface treatments on the hard relining of CAD-CAM denture bases.

The aim of this study was to evaluate the impact of mechanical roughening, adhesive applications, and aging on the bonding between CAD-CAM denture base materials with distinct chemical contents and hard relining material. A total of 300 denture base specimens were produced by additive, subtractive, and conventional heat-polymerization techniques (N=100). The specimens have been classified into five subgroups based on the particular surface treatments administered (n=20): (1) Hard relining material's adhesive application (control); (2) Tungsten carbide bur application for 1min, and hard reline material's adhesive application; (3) Airborne-particle abrasion (APA) with 110 μm Al2O3, and hard reline material's adhesive application; (4) Scotchbond Universal application; and (5) Visio.link application. Representative specimens from each subgroup were examined under a Scanning Electron Microscope (SEM). Subsequently, self-cure hard relining material was condensed in the center of the specimens. Half of the specimens were thermally aged with 5000 cycles at 5°C-55°C. The shear bond strength (SBS) test was performed, and failure loads were recorded. The data was evaluated by Robust ANOVA and Bonferroni test (p<0.05). No statistically significant difference was obtained between the production techniques (p = 0.051). The lowest SBS was observed in the control group among surface treatments, while mechanical surface treatments and universal adhesive showed the highest SBS for both aged and non-aged groups. Aging caused a significant decrease for all test groups (p=0.001). Mechanical surface treatments and universal adhesive applications are more effective for maintaining adhesion across all production techniques.

Does the internal surface treatment technique for enhanced bonding affect the color, transparency, and surface roughness of ultra-transparent zirconia?

To investigate the effects of different surface treatments and thicknesses on the color, transparency, and surface roughness of ultra-transparent zirconia. A total of 120 Katana ultra-translucent multi-layered zirconia specimens were divided into 12 groups according to the thickness (0.3, 0.5, and 0.7mm) and surface treatment (control, airborne particle abrasion [APA], lithium disilicate coating, and glaze on). Color difference (ΔE00) and relative translucency parameter (RTP00) were calculated using a digital spectrophotometer. The surface roughness (Ra, Rq, Sa, and Sq) was measured using a non-contact profile scanner. The surface morphologies and microstructures of the samples were observed using a tungsten filament scanning electron microscope. Statistical analyses were performed by one-way and two-way analysis of variance (ANOVA) followed by post hoc multiple comparisons and Pearson's correlation (α = 0.05). The results showed that the surface treatment, ceramic thickness, and their interactions had significant effects on ΔE00 and RTP00 (p < 0.001). The surface treatment significantly altered the micromorphology and increased the surface roughness of the ceramic samples. APA exhibited the lowest transparency, largest color difference, and highest surface roughness. Zirconia with 0.3mm and 0.7mm thicknesses showed strong negative correlations between Sa and RTP00. The three internal surface treatments significantly altered the surface roughness, color difference, and transparency of ultra-transparent zirconia. As the thickness increased, the influence of the inner surface treatment on the color difference and transparency of zirconia decreased. For new zirconia internal surface treatment technologies, in addition to considering the enhancement effect on the bonding properties, the potential effects on the color and translucency of high-transparency zirconia should also be considered. Appropriately increasing the thickness of zirconia restorations helps minimize the effect of surface treatment on the optical properties.

Effects of Er,Cr:YSGG Laser Surface Treatments and Composites with Different Viscosities on the Repair Bond Strength of CAD/CAM Resin Nanoceramic.

This study aims to evaluate the repair micro-shear bond strength of the CAD/CAM resin nanoceramic block treated using four different surface treatments and composite resins of different viscosities. For the current study, 96 samples with dimensions of 14 × 12 × 2 mm were obtained from a CAD/CAM resin nanoceramic block (Cerasmart) with a low-speed precision cutting saw under water cooling. The relevant samples were randomly divided into four groups according to the surface treatment processes: grinding with diamond bur, aluminum oxide airborne-particle abrasion, long-pulse laser, and short-pulse laser. Following silane application, universal adhesive was applied to all surface-treated samples and cured with an LED for 10 s. The samples prepared for the repair procedure were divided into two subgroups (microhybrid composite and injectable composite) according to the viscosity of the repair material to be used (n = 12). After the repair procedure, care was taken to keep the samples in distilled water in an incubator at 37 °C for 24 h. The repair micro-shear bond strength values (μSBSs) of CAD/CAM resin nanoceramic-composite resin complexes were tested. In addition, randomly selected samples from each group were examined with a scanning electron microscope to evaluate the surface topography after both surface treatments and the micro-shear bond strength test. Data were analyzed by two-way ANOVA and Bonferroni test. It was determined that the surface treatment preferred in the repair protocol significantly affected the μSBS value (p < 0.001). While the highest μSBS value was obtained with the short-pulse laser airradiation group, the lowest μSBS values were found in samples with long pulse laser irradiation. However, samples grinded with a bur and airborne-particle abrasion showed similar μSBS values (p > 0.05). The preferred composite viscosity in the repair procedure has a significant effect on the μSBS value (p < 0.001). However, the interaction between the surface treatment and the viscosity of the repair composite does not affect the μSBS values in a statistically significant way (p = 0.193). It may be recommended to clinicians to repair CAD/CAM resin nanoceramic restoration surfaces with injectable composites or after treatment with short-pulse lasers.

Surface Modification of Feldspathic Ceramic Used for Minimally Invasive Restorations: Effect of Airborne Particle Type on the Surface Properties and Biaxial Flexural Strength.

This study aimed to evaluate the effect of airborne particle abrasion with different particles on the surface free energy, roughness, and biaxial flexural strength of a feldspathic ceramic by comparing it with hydrofluoric acid etching, the standard surface treatment, and polishing. Square-shaped feldspathic ceramic specimens (12 mm × 12 mm × 1.2 mm) were divided into subgroups as airborne particles abraded with alumina (AO3a, AO3b, AO25, AO50a, AO50b, AO90, AO110a, AO110b, AO120a, and AO120b), silica (SO50a, SO50b, SO100, and SO100/200), or nutshell granule (NS100/200), hydrofluoric acid etched, and polished (n = 12). Surface free energy (n = 5), roughness (n = 5), biaxial flexural strength (n = 12), and Weibull moduli (n = 12) were investigated. Data were evaluated with 1-way ANOVA and Tukey HSD tests, and possible correlations were investigated with Pearson's correlation (α = 0.05). SO100/200 mostly had lower surface free energy (p ≤ 0.011), and polishing and etching led to higher surface free energy than AO3a, AO3b, and AO120a (p ≤ 0.031). Polished, SO100, and SO50b specimens mostly had lower roughness and AO125 had the highest roughness (p ≤ 0.029). SO100/200 mostly had lower biaxial flexural strength (p ≤ 0.041), and etched specimens had higher biaxial flexural strength than AO120a, AO120b, and SO50b (p ≤ 0.043). AO3b had the highest (33.56) and AO120b had the lowest (11.8) Weibull modulus. There was a weak positive correlation between the surface free energy and the biaxial flexural strength (r = 0.267, p = 0.011). A larger particle size mostly resulted in higher roughness, which was also affected by the particle shape. Most of the test groups had similar biaxial flexural strength to that of the hydrofluoric acid-etched group. Therefore, for tested feldspathic ceramic, airborne particle abrasion with tested parameters may be a suitable alternative without causing any further damage.

(Kesan Rawatan Permukaan pada Ikatan Struktur Mikro antara Muka Zirkonia-Dentin terhadap Saiz Zarah Serbuk Zirkonia yang Berbeza)

Zirconia-based materials have emerged as promising resources for dental restoration applications owing to their excellent strength and aesthetic appearance. In clinical practices, surface treatment on zirconia is essential to ensure enhanced dental bonding. In this study, a novel method was used to produce zirconia block, and the influence of surface treatment on zirconia-dentine microstructure bonding interface was investigated for different particle sizes of zirconia powder. The particle sizes used in this study were 90 and 30 nm on the basis of manufacturer claims. A zirconia block of both particle sizes underwent surface treatment airborne-particle abrasion (50 μm, 0.4 MPa). Dentine specimens were prepared from extracted premolars stored in 0.1% tymol solution before being randomly cemented with the zirconia block sample by using self-adhesive resin cement (RelyX U2000 Clicker, 3M) and then light polymerised. The results after surface treatment showed higher surface roughness values for 90 and 30 nm at 0.17 and 0.18 μm, respectively, than those of the sample without surface treatment at 0.05 and 0.06 μm, respectively, showing no significant difference between particle sizes. Surface treatment improved the bonding of zirconia because the surface roughness allowed for enhanced interlocking of the cement onto the zirconia surface. However, the unbonded dentine and cement was due to the existence of a smear layer on the dentine surface that prevented the selfadhesive resin cement to work well with the dentine surface. Thus, dentine primer must be used to chemically remove the layer and allow for proper bonding between the resin cement and dentine surface.

Different surface treatments on recently introduced CAD-CAM resin-modified ceramics: Implications on bond strength

Statement of problemThe diverse chemical composition of recently introduced resin-modified ceramics complicates the establishment of a universally accepted clinical bonding protocol. PurposeThe purpose of this in vitro study was to evaluate the influence of different surface treatments of resin-modified ceramics on the bond strength to a resin cement. Material and methodsSixteen 10×12×3-mm resin-modified ceramic slices were obtained from each material (Cerasmart; GC, Shofu Block HC; Shofu, Vita Enamic; Vita, Evolux hybrid; BlueDent, Alium; Alium). Slices were assigned to 4 groups based on surface treatments: Control (no treatment), airborne-particle abrasion with Al2O3 (Al2O3), conditioning with 9% HF (HF), and Al2O3+HF. After treatments and silane coupling agent (Monobond N; Ivoclar) application, 7 resin cement cylinders (Choice 2 veneer; Bisco) were built on each slice and light polymerized for 20 seconds. Half of the specimens (n=14 cylinders) were stored for 24 hours, and the other half were thermocycled (20 000 cycles, 5 °C to 55 °C, 30-second dwell time). Microshear bond strength was tested and analyzed with 3-way ANOVA and the Tukey HSD test (α=.05), and failure patterns were classified. Surface morphology after treatments was observed with scanning electron microscopy and Raman spectroscopy. ResultsAfter 24 hours, all treatments induced higher bond strength (P<.05) than in the control in Evolux. Al2O3+HF caused higher bond strength (P<.05) than in the control in Cerasmart and Shofu, and higher bond strength than Al2O3 in Cerasmart. However, it resulted in lower bond strength (P<.05) than Al2O3 in Alium. After thermocycling, irrespective of the resin-modified ceramic, all treatments induced higher bond strength (P<.05) than in the control. HF induced lower bond strength (P<.05) than Al2O3 in Alium. Al2O3+HF caused the highest bond strength (P<.05) in Evolux and higher bond strength (P<.05) than HF in Vita Enamic. Adhesive failures were prevalent under control conditions, and mixed failures were common after treatments. Al2O3 induced surface alterations in all resin-modified ceramics. HF notably altered Vita Enamic, while it had no noticeable impact on the other resin-modified ceramics. Al2O3+HF caused a considerable alteration in Vita Enamic and modified the other resin-modified ceramics. Vita Enamic had the characteristic vibrational bands of inorganic compounds, while the other resin-modified ceramics exhibited distinct bands associated with organic compounds. ConclusionsAirborne-particle abrasion with Al2O3 followed by HF yielded the highest bond strength, regardless of the resin-modified ceramic, except for Alium, which demonstrated better bond strength after airborne-particle abrasion with Al2O3. 9% HF for 30 seconds caused notable surface alterations in Vita Enamic, negatively impacting its bond strength. Vita Enamic was the only resin-modified ceramic displaying both organic and inorganic composition, while the other resin-modified ceramics showed predominantly organic composition.

Effect of femtosecond laser induced surface patterns on the flexural strength of monolithic zirconia.

To investigate how patterns generated by femtosecond (fs) laser and femtosecond laser power affect the surface roughness (Ra) and biaxial flexural strength (BFS) of monolithic zirconia. Eighty disk-shaped zirconia specimens were divided into eight subgroups (n = 10): Control (C), airborne-particle abrasion (APA), 400 mW fs laser (spiral [SP(400)], square [SQ(400)], circular [CI(400)]), and 700 mW fs laser ([SP(700)], [SQ(700)], [CI(700)]). Ra values were calculated by using a surface profilometer. One additional specimen per group was analyzed with scanning electron microscopy and x-ray diffractometry. BFS values were obtained by using the piston-on-3-ball test. One-way ANOVA and either Tukey's HSD (BFS) or Tamhane's T2 (Ra) tests were used to evaluate data (α = 0.05). Regardless of the pattern and power, fs laser groups had higher Ra than C and APA, while SP groups had lower Ra than CI and SQ groups (p ≤ 0.004). For each pattern, Ra increased with higher laser power (p < 0.001), while the laser power did not affect the BFS (p ≥ 0.793). CI and SQ groups had lower BFS than the other groups (p ≤ 0.040), whereas SP groups had similar BFS to C and APA (p ≥ 0.430). Fs laser microstructuring with spiral surface pattern increased the Ra without jeopardizing the BFS of zirconia. Thus, this treatment might be an option to roughen tested zirconia.

Influence of handheld nonthermal plasma on shear bond strength of polyaryletherketone to resin-matrix cement

Background/purposeChallenges exist regarding the bonding efficiency of polyaryletherketone (PAEK), a high-performance thermoplastic, attributed to its chemical inertness and hydrophobic surface, hindering effective bonding with resin-matrix cement. This research explored the impact of handheld nonthermal plasma (HNP), under varying operational parameters, on PAEK surface wettability and changes in bonding performance with cement. Materials and methodsThree types of disc-shaped PEAK specimens were prepared, with surface treatments categorized as grinding, airborne-particle abrasion (APB), and HNP. Surface wettability was analyzed using a contact angle analyzer (n = 10). Specimens were bonded with resin cement and subjected to artificial aging tests: distilled water bath (NA), thermocycling, and highly accelerated stress tests (n = 10 for each test). Shear bond strength (SBS) was measured, failure modes were analyzed, and statistical analyses were conducted. ResultsThe HNP markedly improved PAEK surface wettability, achieving superhydrophilicity (P < 0.05). This effect intensified with extended operation times (30 or 60 s) and reduced elapsed times (<30 s). HNP-treated PAEK exhibited higher SBS than APB (P < 0.05) and maintained bonding durability after artificial aging, particularly in ketone-enriched variants. Failure analysis revealed predominantly adhesive failure under APB–NA treatment, mixture failures under HNP–NA treatment and postaging, but no cohesive failure. ConclusionThe HNP device benefits dental settings by transforming the PAEK surface into superhydrophilic properties, thereby improving PAEK–cement bonding. It significantly enhances bond durability within 30 s of operation and after a 30 s elapsed period. It is noteworthy that ketone-enriched PAEK demonstrates markedly improved bonding performance.

Effect of Particle Size and Application Pressure in Air-Borne Particle Abrasion on the Adhesion of Polyetheretherketone.

This study aims to investigate the effect of different particle sizes and pressures on the shear bond strength (SBS) and the roughness (Ra) of polyetheretherketone. A total of 117 polyetheretherketone specimens were fabricated and divided into a control (CN: no air-particle abrasion) and eight pre-treatment groups (air-abraded with 50- or 110-μm Al2O3 particles at 1(A), 1.5(B), 2(C), and 2.5(D) bar). The adhesive, Visio.link was used. Thermal aging was performed. Surface properties, SBS and failure mode were assessed. Data was analyzed by linear regression, Pearson correlation and Dunnett's T3 test for pairwise comparisons (p⟨0.05). The highest and lowest Ra were found in the 110D and CN groups respectively, and the highest SBS results were obtained from the 50B group. Pressure and particle size showed significant difference on the investigated properties (p⟨0.001). Only adhesive failure was observed in the CN, and resin cohesive failure was observed in addition to adhesive failure in the overall study groups. The air-borne particle abrasion procedures and the adhesive material combination are critical to the strength of the polyetheretherketone bond. The combination of visio.link with the pre-treatment option of 50-μm Al₂O₃ particles applied at 1.5-bar pressure delivered the most favorable results.

The influence of Zircos-E® etchant, silica coating, and alumina air-particle abrasion on the debonding resistance of endocrowns with three different preparation designs.

The study aimed to evaluate the debonding resistance of three different endocrown designs on molar teeth, using three different zirconia surface pretreatments. Ninety human mandibular first molars were divided into three main groups: endocrowns without ferrule, with 1 mm ferrule, and with 2 mm ferrule. The subgroups were defined by their surface pretreatment method used (n = 15): 50 μm alumina air-particle abrasion, silica coating using 30 μm Cojet™ particles, and Zircos-E® etching. The endocrowns were fabricated using multilayer zirconia ceramic, cemented with self-adhesive resin cement, and subjected to 5000 thermocycles (5-55°C) before debonding. The data obtained were analyzed using a two-way ANOVA. All test specimens survived the thermocyclic aging. The results indicated that both the preparation design and the surface treatment had a significant impact on the resistance to debonding of the endocrowns (p < .001). The 2 mm ferrule followed by the 1 mm ferrule designs exhibited the highest debonding resistance, both were superior to the endocrown without ferrule. Zircos-E® etching and silica coating yielded comparable debonding resistance, which were significantly higher than alumina air-particle abrasion. All endocrowns demonstrated a favorable failure mode. All designs and surface treatments showed high debonding resistance for a single restoration. However, ferrule designs with Zircos-E® etching or silica coating may represent better clinical options compared to the nonferrule design or alumina airborne-particle abrasion. Nonetheless, further research, including fatigue testing and evaluations with different luting agents is recommended.

Bond Strength of Milled and Printed Zirconia to 10-Methacryloyloxydecyl Dihydrogen Phosphate (10-MDP) Resin Cement as a Function of Ceramic Conditioning, Disinfection and Ageing.

This study aimed to assess the suitability of printed zirconia (ZrO2) for adhesive cementation compared to milled ZrO2. Surface conditioning protocols and disinfection effects on bond strength were also investigated. ZrO2 discs (n = 14/group) underwent either alumina (Al2O3) airborne particle abrasion (APA; 50 µm, 0.10 MPa) or tribochemical silicatisation (TSC; 110 µm Al2O3, 0.28 MPa and 110 µm silica-modified Al2O3, 0.28 MPa), followed by disinfection (1 min immersion in 70% isopropanol, 15 s water spray, 10 s drying with oil-free air) for half of the discs. A resin cement containing 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) was used for bonding (for TSC specimens after application of a primer containing silane and 10-MDP). Tensile bond strength was measured after storage for 24 h at 100% relative humidity or after 30 days in water, including 7500 thermocycles. Surface conditioning significantly affected bond strength, with higher values for TSC specimens. Ageing and the interaction of conditioning, disinfection and ageing also impacted bond strength. Disinfection combined with APA mitigated ageing-related bond strength decrease but exacerbated it for TSC specimens. Despite these effects, high bond strengths were maintained even after disinfection and ageing. Adhesive cementation of printed ZrO2 restorations exhibited comparable bond strengths to milled ZrO2, highlighting its feasibility in clinical applications.

Shear bond strength of ultraviolet-polymerized resin to 3D-printed denture materials: Effects of post-polymerization, surface treatments, and thermocycling.

The purpose of this study is to compare the shear bond strength of ultraviolet (UV)-polymerized resin to 3D-printed denture materials, both with and without post-polymerization. Moreover, the effects of surface treatment and thermocycling on shear bond strength after post-polymerization were investigated. Cylindrical 3D-printed denture bases and teeth specimens were prepared. The specimens are subjected to two tests. For Test 1, the specimens were bonded without any surface treatment or thermal stress for comparison with and without post-polymerization. In Test 2, specimens underwent five surface treatments: untreated (CON), ethyl acetate (EA), airborne particle abrasion (APA) with 50 μm (50-APA) and 110 μm alumina (110-APA), and tribochemical silica coating (TSC). A UV-polymerized resin was used for bonding. Half of the Test 2 specimens were thermocycled for 10,000 cycles. Shear bond strength was measured and analyzed using Kruskal-Wallis and Steel-Dwass tests (n = 8). In Test 1, post-polymerization significantly reduced shear bond strength of both 3D-printed denture materials (P < 0.05). No notable difference was observed between the denture teeth and the bases (P > 0.05). In Test 2, before thermocycling, the CON and EA groups exhibited low bond strengths, while the 50-APA, 110-APA, and TSC groups exhibited higher bond strengths. Thermocycling did not reduce bond strength in the latter groups, but significantly reduced bond strength in the EA group (P < 0.001). Post-polymerization can significantly reduce the shear bond strength of 3D-printed denture materials. Surface treatments, particularly APA and TSC, maintained bond strength even after thermocycling.

Osteoblast cell behavior on polyetheretherketone dental implant surfaces treated with different grit size aluminum oxide particles: An in vitro analysis

The hydrophobic and bioinert nature of polyetheretherketone (PEEK) implants needs to be addressed for successful osseointegration. The purpose of this in vitro study was to evaluate the osteoblast cell behavior on PEEK implant surfaces treated with airborne-particle abrasion using different grit size aluminum oxide (Al2O3) particles. Disk-shaped specimens (n=96) were prepared from medical grade PEEK rods and were distributed into 4 groups (n=24) of untreated PEEK (PEEK 0), airborne-particle abrasion using 50-μm Al2O3 particles (PEEK 50), airborne-particle abrasion using 110-μm Al2O3 particles (PEEK 110), and airborne-particle abrasion using 150-μm Al2O3 particles (PEEK 150). The surface characteristics were assessed using water contact angle (WCA) measurements and scanning electron microscopy (SEM). MG-63 osteoblast cells were cultured, and the biocompatibility of PEEK was assessed using a CellTiter-blue cell viability assay and florescence staining at day 1, 3, and 7. The specimens were stained with Alizarin red to assess the osteoblast cell differentiation on day 10 and 14. The Levene test was used to test the homogeneity of variances. One-way and Welch ANOVA with post hoc corrections were used to assess the overall statistical significance of differences among the groups (α=.05). The lowest mean WCA was demonstrated in PEEK 150 (49.25 ±5.51) and the highest in PEEK 0 (89.14 ±4.24) (P<.001). SEM images of PEEK 150 illustrated a more complex structure with a large area of globular outcroppings throughout the surface. PEEK 150 showed the highest cell metabolic activity at each time point with florescence staining showing a substantial cell confluence at day 3 and 7. Although PEEK 150 did not show a significant increase in cell proliferation, the number of cells attached was significantly higher than other groups (P<.05). PEEK 110 and 150 also showed a substantial increase in the extent of mineralization. Airborne-particle abrasion using moderate Al2O3 grit size (110- or 150-μm) improved the hydrophilicity and osteoblast cell behavior on PEEK implants.

Influence of airborne particle abrasion on dentin bonding effectiveness of a 2-step universal adhesive

ObjectiveTo determine the effect of airborne particle abrasion (APA) on micro-tensile bond strength (µTBS) to dentin using different air-abrasion/polishing powders. MethodsThe bonding effectiveness of G2 Bond Universal (G2B), used in etch-and-rinse (E&R) and self-etch mode (SE), was tested on bur-cut dentin and dentin air abraded/polished using six different powders (aluminum oxide 29 µm (AO29) and 53 µm (AO53), aluminum trihydroxide (AT), sodium bicarbonate (SB), sodium bicarbonate soft (SBsoft) and bioactive glass (BG); Velopex). Adhesive-composite resin specimens were immersed in distilled water at 37 °C for one week and cut into microspecimens. Half of the specimens were subjected to 50,000 thermocycles (aged). Immediate and aged μTBS to dentin were measured. Statistical analysis was performed using linear mixed-effects (LME) modeling (p < 0.05). ResultsComparing the aged bond strengths to air-abraded/polished dentin with bur-cut dentin, pretreatment with SB and SBsoft in combination with G2B used in E&R mode, and BG air polishing in combination with both application modes (E&R, SE), resulted in a significantly higher bond strength. Dentin bond strength was only significantly lower when air abraded with AO29 and using G2B in SE mode. Aging did not significantly influence bond strength for both application modes (E&R, SE), except for AO29 and AT-treated dentin, where bond strengths decrea sed significantly using G2B in SE mode. In general, G2B reached significantly higher bond strengths on air-abraded/polished dentin in E&R mode than in SE mode. ConclusionAir-abrasion/polishing did not impair dentin bond strength using G2B, except when dentin was air abraded with AO29 and using G2B in SE mode. Air polishing positively influenced the bond strength to dentin in specific groups. Clinical significanceAPA is safe concerning bonding to dentin. The E&R application mode is preferred using G2B as adhesive on air-abraded/polished dentin. Air polishing with BG positively influenced dentin bond strength for both application methods.

Targeting bonding protocols to increase the bond between acrylic resin or 3D printed denture bases and prefabricated or 3D printed denture teeth

Statement of problemThe difference in chemical composition between denture base resin and denture teeth requires the development of bonding protocols that increase the union between the materials. PurposeThe purpose of this in vitro study was to evaluate the impact of different bonding protocols on the bond between heat-polymerized and 3-dimensionally (3D) printed acrylic resin denture bases and acrylic resin prefabricated and 3D printed artificial teeth. Material and methodsFour types of artificial teeth were evaluated: prefabricated acrylic resin (VITA MFT) and 3D printed (Cosmos TEMP, PRIZMA 3D Bio Denture, and PrintaX AA Temp) bonded to 20×24-mm cylinders of heat-polymerized (VipiWave) and 3D printed (Cosmos Denture, PRIZMA 3D Bio Denture, and PrintaX BB Base) denture bases. Three bonding protocols were tested (n=20): mechanical retention with perforation + monomer (PT1), mechanical retention with perforation + airborne-particle abrasion with 50-µm aluminum oxide + monomer (PT2), and mechanical retention with perforation + Palabond (PT3). Half of the specimens in each group received 10 000 thermocycles and were then subjected to the bonding test at a crosshead speed of 1 mm/minute. The failure type was analyzed and scanning electron micrographs made. Additionally, surface roughness (Ra) and wettability (degree) were analyzed (n=15). ANOVA was used to evaluate the effect of the bonding protocol, and the Student t test was applied to compare the experimental groups with the control (α=.05). For type of failure, a descriptive analysis was carried out using absolute and relative frequency. The Kruskal-Wallis test was used to evaluate the surface changes (α=.05). ResultsAmong the protocols, PT3 with in Yller and PT2 with Prizma had the highest bond strengths of the heat-polymerized denture base and 3D printed teeth (P<.05). When comparing the experimental groups with the control, PT3 and PT2 had greater union with the 3D printed denture base + 3D printed teeth (in Yller), with no difference from the heat-polymerized denture base + prefabricated teeth in acrylic resin. The treatment of the 3D printed tooth surfaces affected the surface roughness of Prizma (P<.001) and wettability (P<.001). ConclusionsTo increase the bond between Yller 3D printed denture base + 3D printed teeth, a bonding protocol including mechanical retention with perforation + Palabond or mechanical retention with perforation + airborne-particle abrasion with aluminum oxide + monomer is indicated. For the other materials tested, further bonding protocols need to be investigated.

Effect of various surface treatments on relining bond strength of CAD-CAM denture base materials.

The aim of this study was to analyze the impact of various surface treatments and production methods on the shear bond strength (SBS) between reline material and denture base resins. One-hundred-twenty specimens were produced using conventional heat-polymerization, subtractive, and additive techniques. Each group consisted of 40 specimens. The specimens were divided into four subgroups, each with 10 samples, for surface treatments. These subgroups were: (1) Control-only monomer application, (2) 50 μm airborne-particle abrasion, (3) 110 μm airborne-particle abrasion, and (4) Roughening with tungsten carbide bur. Representative specimens from each subgroup were examined under SEM. Then, auto-polymerized resin was condensed in the center of the specimens. Specimens were subjected to thermal aging (5000 cycles at 5-55°C). The SBS test was conducted and failure loads were recorded. The data were evaluated by two-way ANOVA and Tukey pairwise multiple comparisons method (p < 0.05). The additively produced group showed significantly lower SBS than conventional and subtractive groups (p < 0.001), with no significant differences between the subtractive and conventional groups. Specimens that underwent monomer application only showed the lowest SBS among surface treatments, while 50 μm airborne-particle abrasion showed the highest SBS. Based on the partial eta-squared analysis results, the surface treatment mainly impacted SBS. Among the surface treatment methods, treating denture bases with 50 μm airborne-particle abrasion is more effective for maintaining adhesion, especially in the additive technique.