Air Temperature Research Articles

Free convective heat transfer induced inside a vented duct having two aligned hot and cold cylinders: An experimental study

AbstractFree convective heat transfer created from two aligned cylinders immersed inside a vented air duct is experimentally investigated. The experiments include the measurements of cylinders temperature and the air temperature inside the enclosure under steady, turbulent, and incompressible flow properties by using steady‐state heat equations. The studied parameters include Rayleigh number (), opening sizes at lower and upper enclosure surfaces (), and space size between cylinders () with the constant ratio of enclosure width to cylinder diameter equal to 6. The findings displayed that the average air temperature inside the enclosure for the low values of S and O is low, and it rises as S is raised. The behaviors of Nu differ with changing Ra values. An interaction between hot cylinder and cold cylinder inside the enclosure is observed that depends on O and S values, and hence, they have a large impact on fluid temperature. The data indicated that rises with the for all and values. The value of for each cylinder depends on the values of and . The maximum value has been obtained when and with maximum enhancement between 30% and 50% depending on Ra values as compared with and , whereas the minimum average has been indicated when and . The profiles of reveal that , , and have a considerable influence on heat transfer.

An experimental study of the effects of using cool materials at different building heights on the indoor and outdoor environment

Four building arrays, each comprising 25 building models, were utilized to investigate the effects of cool materials on building surface temperatures, indoor temperatures, and street microclimates in Guangzhou, China. The experiments are divided into three groups. The first group of the experimental models is used to investigate the cooling effect of the roof using cool materials on the roof surface and indoor environment. The results show that using cool materials on roofs can significantly reduce roof surface and indoor temperatures of the top floor by 13.5 °C and 3.9 °C at noon under an average global solar radiation (GSR) of 727 W/m2. The second group of experiments included four arrays: one control group without cool materials and three other arrays applying cool materials on the third, second, and first floors, respectively. Using cool materials on the façades of the third, second, and first floors reduced the indoor temperature by an average of 1.9 °C, 0.8 °C, and 0.5 °C (average GSR = 404 W/m2), respectively. As a result, higher floors receive more solar radiation, and cool materials show better cooling capacity. The third group is used to investigate the effect on street air temperatures when cool materials are used on all building façades. Overall, the effect of cool materials on the street air temperature is very small, with a maximum reduction of only 0.2 °C in the street air temperature.

Intraspecific variation in responses to extreme and moderate temperature stress in the wild species, Solanum carolinense (Solanaceae)

Abstract Adaptation or acclimation to local temperature regimes has often been used as a proxy for predicting how plant populations will respond to impending novel conditions driven by human-caused climate change. To understand how plants may successfully respond to increasing air temperatures (extreme and moderate) in the future, we explored how temperature tolerance traits differ in populations of Solanum carolinense from northern (MN) and southern (TX) regions of the continental United States in a two-experiment study. In the first experiment, we compared the heat and cold tolerance in vegetative (sporophyte) and reproductive (male gametophyte) traits. In the second experiment, we studied if long-term heat influences plant development by examining how development in moderate heat affected reproductive structures and reproductive success. We found that temperature-sensitivity differed between southern populations, which regularly experience extreme heat, and northern populations that do not. In contrast to our expectations, northern populations appeared more heat-tolerant than southern populations for vegetative traits such as chlorophyll stability and reproductive traits such as pollen germination. Our results are consistent with a heat-avoidance, rather than tolerance mechanism to mitigate extreme heat during pollen germination. In the second experiment, plants developing under the moderate heat treatment had significantly smaller reproductive structures and reduced seed production (27% fewer seeds on average than in the control treatment). Reproductive structures that developed in moderate heat were also reduced in size, particularly in the northern populations relative to populations from the south. We conclude that rising temperatures have the potential to incur substantial negative consequences for the reproductive success of individuals in this species and that some populations already mitigate stressful temperature conditions through phenotypic plasticity.

Microencapsulation of honey as flavouring agent in milk powder

Honey is a natural product commonly used in milk powder for flavoring purposes. Currently, honey flavor is added to milk powder in powder form. This study aimed to investigate the effect of spray drying operating conditions on the quantity and quality parameters of the honey powder recovered. The influence of inlet air temperatures, feed flow rates, and type of microencapsulating agents upon the properties of obtained powders was examined. Spray drying of honey with the addition of maltodextrin DE 18 and 12 was carried out at inlet air temperatures of 150, 170, 190℃ and feed flow rates of 330 and 660 mL/h. The properties of the powders obtained were quantified in terms of moisture content (MC), hygroscopicity (HG) and color. Results of experiments showed higher inlet air temperature and lower feed flow rate led to a significant increase (p<0.05) in powder recovery. The total powder recoveries found in this study were between 39.42±2.35% to 71.92±4.17%, which indicates that this process has the potential to be applied on an industrial scale. The decrease in DE of maltodextrin promoted a higher powder recovery. Furthermore, it was found that the browning index increased with the decreasing inlet air temperature and increasing feed flow rate.

Enhancing citizen science impact in environmental monitoring: Targeted engagement strategies with stakeholder groups

Understanding the motivations and benefits of citizen science (CS) participants is critical to the success of environmental science projects that rely on data collection from engaged citizens. Tailored communication with citizen scientists is essential, leading to the need to target specific societal groups for extensive and high-quality data sets. The purpose of the study was to apply marketing concepts such as stakeholder analysis, value proposition canvas (VPC), and key performance indicators (KPIs) to CS projects. The study examined the extent to which these strategies can be applied to CS projects and add value, resulting in improved recruitment and retention of participants, as well as improved project management. The dynamic landscape of CS projects requires adapted business-oriented approaches supporting ongoing participation with high motivation, acknowledging community needs, and recognizing institutional scientists, akin to targeting potential customers. The case study focuses on the CityCLIM initiative, an EU-funded project collecting urban climate data, especially air temperature, using mobile weather stations. The CityCLIM VPC, analyzing stakeholder groups, facilitated tailored communication strategies by analyzing stakeholder groups and highlighting the effectiveness of the CS cycling initiative within the “Stadtradeln” program. Impact KPIs served as a roadmap for strategic refinement, while data quality KPIs identified deficiencies, guiding adjustments to the campaign. Applied marketing tools improved project planning, engagement, and evaluation, demonstrating the potential of this concept. Adapting marketing tools to recruitment and communication strategies benefits CS projects by targeting specific groups. The holistic integration of stakeholder analysis, VPC, and KPIs streamlines project management and creates a framework for sustainable success. This adaptation forms a robust toolkit for CS project coordinators, contributing to effective communication, engagement, and impact assessment. Applying marketing tools significantly increases CS projects’ reach and impact, ensuring long-term success and meaningful scientific contributions.

Physiological and hygienic assessment of a multilayer set of personal protective equipment against low temperatures made using membrane materials

Introduction. Advanced personal protective equipment (PPE) against low temperatures is a high–tech product created using the latest achievements of science, design designs, ergonomic, aesthetic solutions that determine its thermal protection properties. The use of membrane materials in PPE from low temperatures allows them to combine low weight and high thermal protection properties, low air permeability and sufficient vapor permeability necessary to ensure heat and moisture exchange between humans and the environment. The study aims to determine the thermal protection properties of various sets of multilayer workwear and indicators of heat and moisture exchange of volunteers when modeling professional activity at low air temperature. Materials and methods. The authors have conducted a study in a microclimatic chamber with the participation of six practically healthy male volunteers. The researchers have determined the thermal protection properties of multilayer workwear of various configurations in accordance with GOST R 12.4.185-99 and MUK 4.3.1894-04. As test samples, they have used pipes of three different configurations to protect against low temperatures, wind, water, general industrial pollution and mechanical influences, as well as short-term exposure to open fire. The assessment of heat and moisture exchange indicators of various PPE configurations was carried out by specialists when modeling work activities with measurements of the relative humidity level in the layers of the kits and the level of accumulated moisture in each element of the PPE. Results. The authors have determined the values of thermal insulation of the studied materials and the scope of their application. To assess heat and moisture exchange, two samples of PPE were selected, made using membrane and cotton fabrics with similar thermal insulation values. The analysis of the results of studies of moisture exchange indicators showed a slightly lower efficiency of moisture evaporation of the control sample. The indicator of the relative humidity of the air under the shelter space and between the layers of the package of materials and clothing has shown its informative significance for assessing the effectiveness of moisture transfer from the surface of the human body to the environment. Conclusion. The results of a physiological and hygienic assessment of a set of multilayer clothing made of membrane materials have shown that various combinations of its constituent elements make it possible to create kits that provide adequate protection for an employee in a wide range of air temperatures and wind speeds. The use of membrane materials in combination with structural elements (ventilation openings) provides a more efficient transfer of moisture from the skin surface to the external environment, as evidenced by the values of the relative humidity index of the air under the clothing space and between the layers of clothing. Ethics. The study was approved by the local Ethical committee of the Izmerov Research Institute of Occupational Health (Minutes of the meeting No. 6 dated 07/20/12)

Integrating the Living Wall with Mechanical Ventilation to Improve Indoor Thermal Environment in the Transition Season

A living wall, when integrated with a mechanical ventilation system, can effectively improve the indoor thermal environment and reduce indoor CO2 concentration during the transition season. In this study, a control experiment was conducted to analyze the effect of a living wall integrated with mechanical ventilation (LW-V) on indoor air quality. During the experiment, indoor air temperature, relative humidity, indoor air speed, and CO2 concentration were measured, while the skin temperature was monitored and subjective questionnaires were administered to 60 subjects. The results show that the indoor environment was effectively improved by employing the LW-V system, with the average indoor temperature decreasing by 1.45 °C, while relative humidity increased by 19.1%. Due to the plant photosynthesis, CO2 concentrations were reduced by 13.83 ppm. Meanwhile, the mean skin temperature was reduced by 0.18 °C and was closer to the neutral mean skin temperature. Questionnaire analysis reveals the LW-V system improved overall air freshness sensation and thermal comfort level by 1.09 and 0.53, respectively. The LW-V system improved the indoor thermal environment as well as air quality during the transition season significantly.

Assessing the Effectiveness of Reflective and Diffusive Polyethylene Films as Greenhouse Covers in Arid Environments

The application of diffusive and reflective polyethylene (PE) films as greenhouse coverings in arid climates presents an opportunity to improve the microclimate of the greenhouse and achieve consistent light distribution within the crop canopy. Nevertheless, there is still a lack of understanding regarding the properties of these covers and their impact on the microclimate and the growth parameters of crops. This study aimed to assess the impact of different covers on the diffusion of beam radiation during transmission, microclimatic parameters, and growth parameters of cucumbers in each of the greenhouses they covered. In the study, three PE covers were evaluated: a reflective cover (RC), a diffusive film (DC), and a locally produced cover (LPC) as the control treatment. The covers were installed on three identical, single-span, evaporatively cooled greenhouses named GH1/LPC, GH2/RC, and GH3/DC, which were utilized for cultivating cucumber crops. The results indicated that the diffusive nature of the tested films increased the ratio of diffuse to global solar radiation (D/G) from 0.22 outside the greenhouses to 0.49, 0.42, and 0.41 inside GH1/LPC, GH3/DC, and GH2/RC, respectively. Similarly, the ratio of diffuse to direct beam radiation (D/B) showed an increase, with values of 0.95, 0.70, and 0.68 inside GH1/LPC, GH3/DC, and GH2/RC, respectively, compared to the outside value of 0.28. The DC used in GH3 showed a favorable microclimate by reducing the air temperature and improving the relative humidity. Accordingly, the vegetative growth of the cucumbers was significantly improved in GH3/DC, reflected in increases in their biomass, followed by GH2/RC and GH1/LPC. The highest crop yield (p ≤ 0.05) of 12.3 kg/m2 was achieved in GH3/DC, followed by 10.2 kg/m2 in GH2/RC and 10.1 kg/m2 in GH1/LPC. Interestingly, the LPC not only stood out as a low-cost option but also displayed excellent diffusive–radiative properties, and demonstrated reasonable growth development and productivity for the cucumber crops. Consequently, the LPC emerges as a practical and cost-effective greenhouse covering material for crop production in arid climates.

Enhancement of the precooling system performance for aviation engines by volatile liquid injection

Water injection precooling in aviation engines is a promising technique that can enhance performance, improve efficiency, and reduce emissions, especially at high altitudes and Mach numbers. However, its implementation in aviation engines requires careful engineering and design considerations due to the restricted space available for installation and operation, as well as the challenges posed by high inlet air velocities. Therefore, the present study experimentally and numerically evaluates the effectiveness of spray precooling for jet engines and introduces novel insights into optimizing droplet dynamics and nozzle configurations in short, narrow spray ducts under high inlet air temperature and velocity. The impact of water spray cooling on the uniformity of inlet air is also investigated for nonuniform air temperature conditions, which has yet to be mentioned in previous research. An experimental configuration has been devised and implemented to investigate water injection precooling within a rectangular spray duct. The evaporative cooling process through the spray duct and the injected droplet trajectories were predicted using an Eulerian-Lagrangian computational fluid dynamics (CFD) model. The CFD model was verified using the present experiments, and there is a strong correlation between the experimental data and simulation findings, with an average discrepancy of less than 7%. The effectiveness of the water injection system is investigated at different operating parameters such as nozzle arrangements, coolant type, droplet size, and variable velocities. The results showed that sprays characterized by small mean diameters and high initial droplet velocity significantly enhance spray cooling performance. Changing the nozzle configurations impacts spray cooling performance considerably, with the cross-outside case providing the best results. Notwithstanding its advantageous evaporation rate, introducing methanol via injection does not yield significant enhancements. Water injection is crucial in achieving a more homogeneous temperature distribution by reducing temperature disparities and promoting mixing and evaporation.

Examining the intersection of carceral space and well‐being: Correctional officers' perspectives on old and new prison design

AbstractIn the current study, we explored the prison design and infrastructural changes that Canadian correctional officers consider to be essential in the construction of a new provincial correctional institution intended to replace Her Majesty's Penitentiary (HMP) in the Canadian province of Newfoundland and Labrador. Analyzing 28 semi‐structured interviews conducted with correctional officers employed at HMP, we found the poor working conditions within HMP are, at least in part, related to the physical design of the prison, including inadequate lighting, poor air quality and temperature, high sound levels, and other spatial limitations. Building on the prison design literature, findings suggest that while prison design requires attention to physical security at the forefront, there are ways to improve the space, recognizing how an uncomfortable workplace and living conditions also pose a potential threat to the well‐being and safety of correctional officers and people who are incarcerated.

Acclimation to moderate temperatures can have strong negative impacts on heat tolerance of arctic arthropods

Abstract The Arctic is impacted by some of the fastest temperature changes observed on Earth, but the impact on the terrestrial arthropod fauna is unclear. Acute physiological thermal limits of terrestrial ectotherms from high latitudes often exceed the local air temperatures, suggesting that they may be able to cope with increasing temperatures. However, knowledge on how Arctic terrestrial arthropods cope with elevated temperatures for longer periods is lacking. Here we investigate how acclimation temperature and exposure time affect the acute physiological heat tolerance of five terrestrial arthropod species (Neomolgus littoralis, Megaphorura arctica, Nysius groenlandicus, Psammotettix lividellus and Nabis flavomarginatus) immediately after collection in Arctic and sub‐Arctic habitats. We show that although acute heat tolerances are relatively high, even exposure to moderate (temperature span assessed ca. 3–29°C) acclimation temperatures for a 24 h period have strong negative effects on heat tolerance for four of the five species. Similarly, exposure time negatively affected heat tolerance, but depending on species and temperature. Together our results suggest that exposure to even moderately elevated temperatures for periods of 24 h or even shorter can lead to lower acute heat tolerance for cold adapted terrestrial arthropod species from sub‐Arctic and Arctic regions. Consequently, climate change leading to extended periods of mildly elevated temperatures may have strong negative effects on these species. We argue that this aspect is currently overlooked when assessing the ability of arthropods from Arctic and sub‐Artic regions to cope with climate changes as such predictions are typically based on acute heat tolerance estimates and with the assumption of beneficial acclimation responses. Read the free Plain Language Summary for this article on the Journal blog.

Evaluating the effect of ambient air temperature on the sustainability aspect of naphtha‐based gas turbine power plant

AbstractThe exergy‐based sustainability indices have been a cause of concern for gas turbine power plant as its performance is very sensitive to air temperature. Hence, the present study evaluates the impact of atmospheric air temperature on exergy sustainability and ecological function of a naphtha‐based gas turbine power plant using EES. The outcome of the study shows that combustion chamber (CC_1) needs more attention compared with other components present, and it has least improvement potential as compared with other components. Further while carrying out parametric analysis with respect to ambient air, it was observed that for a 1.1°C increase in atmospheric air temperature a reduction in sustainability index about 0.66% was observed respectively, for GT_1. Thus, this study established that the power plant's exergy sustainability performance has a negative impact at high ambient air temperatures on exergy sustainability indices.

Dust and Bacterial Air Contamination in a Broiler House in Summer and Winter

This study aimed to investigate dust and bacterial air contamination in a broiler house during different seasons. The study was carried out in commercial housing conditions during five weeks of the rearing cycle in summer and winter. The total dust concentration ranged from 1.90 to 4.50 mg/m3 in summer and from 2.80 to 5.10 mg/m3 in winter. The total bacterial count ranged from 2.85 × 104 to 1.03 × 105 CFU/m3 in summer and from 2.12 × 104 to 2.28 × 105 CFU/m3 in winter. The study results showed the dust concentration to be increased in winter as compared to summer, yielding a significant correlation (r = 0.602, p < 0.05) with a significantly higher airborne bacterial count in winter (p < 0.001). Furthermore, dust concentration showed significant correlations (p < 0.05) with air temperature (r = −0.418), relative humidity (r = 0.673), and broiler activity (r = 0.709), while bacterial count yielded significant correlations (p < 0.05) with air temperature (r = −0.756), relative humidity (r = 0.831), and airflow rate (r = 0.511). The results obtained in the study can prove useful in the field. Seasonal variability in dust and bacterial air contamination should be considered in the development of guidelines or standards of air quality in broiler housing and evaluation of the effectiveness of remedial strategies.

Evaluation of the Activity of a Municipal Waste Landfill Site in the Operational and Non-Operational Sectors Based on Landfill Gas Productivity

This research identifies the productivity of landfill gas actively captured at a municipal waste landfill site with a waste mass exceeding 1 million Mg from sectors in the operational and non-operational phases, considering meteorological conditions. Based on the analysis of landfill gas, including emissions and composition (CH4, CO2, O2, and other gases), the processes occurring demonstrate the impact of the decomposition of deposited waste on the activity of the deposit. With average monthly gas emissions exceeding 960,000 m3, the average content of CH4 (30–63%) and CO2 (18–42%) and the varied content of O2 (0.3–9.8%) in individual sectors of the landfill site were significant. The statistically significant relationship between CH4, CO2, and landfill gas emissions exhibited a noticeable decrease in methane content. Despite the abandonment of waste storage, a high correlation is present between the emission level and methane content (0.59) and carbon dioxide (0.50). In the operational part of the landfill, this relationship is also statistically significant but to a lesser extent; Spearman’s R-value was 0.42 for methane and 0.36 for carbon dioxide. The operational and post-operational phases of the municipal waste landfill demonstrated a noticeable impact from the amount of precipitation, relative humidity, and air temperature, on landfill gas productivity. The generally progressive decline in the activity of the waste deposit, which reflects a decreasing trend in the methane content of approximately 2% annually in the total composition of landfill gas, as well as the share below 50%, indicates the need only to utilise landfill without producing energy.

Consistent Ground Surface Temperature Climatology Over China: 1956–2022

AbstractThe ground surface represents the land‐atmosphere interface and plays a crucial role in exchanging energy, matter, and biochemical fluxes. The ground surface temperature (Ts) is hence widely investigated as an indicator to understand the thermal state of soil in a warming world. However, regular and continuous Ts measurements are rare worldwide, and the early Ts records were derived from snow surface measurements and are not comparable with the measurements of modern automatic systems. In this study, we reconstruct the Ts records of the China Meteorological Administration (CMA) for 1956–2022 by numerical simulation. The results show that the mean annual ground surface temperature (MAGST) during 1981–2010 ranged from 0.4 to 30.8°C at 632 stations. The MAGST was mainly controlled by air temperature and refined by snow depth. The overall MAGST increased by 0.20 ± 0.02°C dec−1 across China during 1956–2022 and showed pronounced interdecadal variability corresponding to the surface air temperature (0.23 ± 0.03°C dec−1). At the snow‐covered sites, the Ts warming was amplified by increased snow depth, leading to about 0.24°C dec−1 (or 70.6%) faster warming for Ts in winter compared to that of surface air temperature. Many of the early reported ground surface temperature studies based on CMA measurements did not consider the measurement inconsistency and likely overestimated the warming trend of ground surface temperature over China.

Partitioning urban forest evapotranspiration based on integrating eddy covariance of water vapor and carbon dioxide fluxes

Partitioning of evapotranspiration (ET) in urban forest lands plays a vital role in mitigating ambient temperature and evaluating the effects of urbanization on the urban hydrological cycle. While ET partitioning has been extensively studied in diverse natural ecosystems, there remains a significant paucity of research on urban ecosystems. The flux variance similarity (FVS) theory is used to partition urban forest ET into soil evaporation (E) and vegetation transpiration (T). This involves measurements from eddy covariance of water vapor and carbon dioxide fluxes, along with an estimated leaf-level water use efficiency (WUE) algorithm. The study compares five WUE algorithms in partitioning the average transpiration fraction (T/ET) and validates the results using two years of oxygen isotope observations. Although all five FVS-based WUE algorithms effectively capture the dynamic changes in hourly scale T and E across the four seasons, the algorithm that assumes a constant ratio of intercellular CO2 concentration (ci) to ambient CO2 concentration (ca) provides the most accurate simulation results for the ratio of T/ET. The performance metrics for this specific algorithm include the RMSE of 0.06, R2 of 0.88, the bias of 0.02, and MAPE of 8.9 %, respectively. Comparing urban forests to natural forests, the T/ET in urban areas is approximately 2.4–25.3 % higher, possibly due to the elevated air temperature (Ta), greater leaf area index (LAI), and increased soil water availability. Correlation analysis reveals that the T/ET dynamic is primarily controlled by Ta, LAI, net radiation, ca, and soil water content at half-hourly, daily, and monthly scales. This research provides valuable insights into the performance and applicability of various WUE algorithms in urban forests, contributing significantly to understanding the impact of urbanization on energy, water, and carbon cycles within ecosystems.

Temporal dynamics of drinking water sodium levels in coastal areas, Cyprus 2009–2020

Around the world, groundwater salinity levels are increasing in coastal areas, as a result of its systematic overexploitation for domestic, agricultural and industrial demand and potentially due to climate change manifestations (such as, sea level rise). We hypothesized that the groundwater quality of many Mediterranean coastal areas is already being perturbed, especially for water salinity, depending on the groundwater distance from the seafront. The objectives of this study were: i) to evaluate the magnitude and temporal variance of drinking water sodium (Na) as a metric of salt intake used for public health purposes using drinking water data in Cyprus; and ii) to examine the degree of Na enrichment in drinking water as defined by the seawater coastline distance of each sampling point. Open access governmental data of drinking water Na (n = 3304), daily max ambient air temperature and total rainfall were obtained for the period of 2009–2020 from governmental repositories. Linear mixed-effect regression models of drinking water Na with unsupervised covariance matrix were used. After adjusting for temperature and rainfall data, there was a significant annual increase in drinking water Na levels over time (beta = 0.01; 95 % CI: 0.00, 0.02; p = 0.02) for the coastal areas (<10 km from coastline, cutoff used by the EU Environment Agency), but this was not the case for non-coastal areas (>10 km distance from coastline). The distance of each sampling point from the coastline in Cyprus was negatively associated with drinking water Na in coastal areas (beta = −0.04, 95%CI: −0.06, −0.01; p = 0.002); this was not the case for non-coastal areas. More research is warranted to better understand the impacts of global environmental change on water quality in association with the burden of disease in coastal areas.

Numerical simulation and geometric optimization of a desalination system using solar energy using two-phase mixing method with alumina nanoparticles

This research paper presents 2D numerical simulations of a single-slope solar desalination system from a nanomaterial science perspective, utilizing the two-phase mixture method. Alumina nanoparticles with a volume percentage of 0.1 % are introduced into the water storage tank for thermal analysis. The system features a trapezoid-shaped glass wall to harness solar energy. Key variables studied encompass ambient temperature, glass wall angle, front wall height, glass wall temperature, and air temperature inside the system. Temperature and velocity contours within the system are obtained through numerical simulations. To enrich the analysis, artificial intelligence techniques and response surface methodology are employed to examine the maximum and minimum temperatures. The results indicate that, at medium ambient temperatures, the lowest maximum air temperature inside the desalination system occurs at a front wall height of 0.2 m and a glass angle of 45°. Additionally, the lowest air temperature is observed at an ambient temperature of 10 °C and a front wall height of 0.05 m, corresponding to a glass angle of 27.5°. On the other hand, the highest maximum air temperature is recorded at a front wall height of 0.125 m, with a glass angle of 45° and an ambient temperature of 55 °C. Increasing the ambient temperature from 10 °C to 55 °C for a wall height of 0.2 m leads to a 26.81 °C rise in the air temperature inside the system, equivalent to a 9 % increase. The findings provide valuable insights for optimizing the design and performance of single-slope solar desalination systems integrated with alumina nanoparticles from the perspective of nanomaterial science.

Projection of mean and extreme precipitation and air temperature over India: a CMIP6 analysis

ABSTRACT This study used fifteen Coupled Model Intercomparison Project Phase 6 (CMIP6) models to analyze the mean and extreme projection precipitation during the Indian summer monsoon (ISM) season, i.e., June to September (JJAS). A continuous rise in precipitation and its associated unpredictability were predicted by global climate models using the CMIP6. The extreme values are estimated on the basis of generalized extreme value (GEV) distribution. Four socioeconomic paths are used as SSP126, SSP245, SSP370 and SSP585 to understand the impact of low-emission to high-emission scenarios. In all the scenarios, it is seen that all the models predict a significant rise in JJAS mean and extreme precipitation. Moreover, a strong correlation is obtained between the historical (1995–2014) and near-emission future simulation (2021–2040), mid-emission future simulation (2041–2060), high-emission future simulations (2081–2100) of air temperature and precipitation. In extreme emission scenarios, ensemble mean of CMIP6 models shows an increasing amplitude in surface air temperature and precipitation over India in the near future (2021–2040), mid future (2041–2060) and the end of the century (2081–2100). The CMIP6 simulations mainly support the results of all models, but they also demonstrate improved robustness across models.

Exploring the Multi-Sensory Coupling Relationship of Open Space on a Winter Campus

Exploring the combined effects of multisensory interactions in open spaces can help improve the comfort of campus environments. Nine typical spaces on a university campus in Fuzhou were selected for this study. Subjects perceived the environment and then completed an on-site subjective questionnaire. At the same time, meteorological data (global radiation, air temperature, globe temperature, wind speed, relative humidity, and illumination intensity) were measured to determine the interactions between visual and acoustic and thermal perceptions. Differences in the meteorological parameters between the measuring points were described using a one-way ANOVA and Tukey’s post hoc test, and a chi-square test of independence was used to determine significant associations between thermal, acoustic, and visual comfort, which in turn led to the study of interactions between visual, acoustic, and thermal comfort using a two-way ANOVA. The following conclusions were drawn: (1) the Thermal Comfort Vote (TCV) increased with the increasing Acoustic Comfort Vote (ACV) at all levels of thermal stress. (2) The highest and lowest Acoustic Sensation Vote (ASV) values for each sound type were derived from either “slightly cold” or “warm” conditions. Both the Thermal Comfort Vote (TCV) and the Acoustic Comfort Vote (ACV) were positively correlated. (3) When “neutral”, the Thermal Sensation Vote (TSV) increased with increasing illumination intensity (LUX). (4) The Sunlight Sensation Vote (SSV) increased with the increasing Universal Thermal Climate Index (UTCI) when illumination intensity (LUX) was moderate and bright. (5) The highest and lowest Acoustic Sensation Vote (ASV) values for each sound type came from either “slightly cold” or “warm” conditions.