Air-guiding Photonic Bandgap Fiber Research Articles

Effect of single point defects on the confinement losses of air-guiding photonic bandgap fibers

The confinement losses in air-guiding photonic bandgap fibers (PBGFs) with air hole missing are studied with the full-vector finite-element method. It is confirmed that there are two loss peaks (1.555 and 1.598 μm) if there is a hole missing in the cladding far from the core. The closer to the core the hole missing is, the larger the confinement losses are, and even no mode could propagate in the core. The main power of the fundamental mode leaks from the core to the cladding defect. The quality of PBGFs can be improved through controlling the number and position of defects.

Structural Optimization of Air-Guiding Photonic Bandgap Fibers for Realizing Ultimate Low Loss Waveguides

In this paper, we investigate the ultimate low loss property for several realistic core shapes in triangular-type air-guiding photonic bandgap fibers (PBGFs) through a full-vector modal solver based on the finite element method. We show that the surface mode free condition is expressed as a normalized silica-ring thickness T = 0.5 for any core size and the cladding structural parameters, regardless the core radius of the silica-ring is one of the main factors of dominating the surface mode's condition, and the wavelength range of the PBG changes on varying the structural parameters of the cladding. Moreover, we propose a novel type of PBGF without surface mode, which exhibits lower scattering losses caused by surface roughness of the silica-ring in comparison to 19 cell-core PBGFs and suppresses the mode coupling between fundamental-like and higher order modes when compared to 37 cell-core PBGFs.

Hollow-core photonic bandgap fibers based on a square lattice cladding

We propose a novel air-guiding photonic bandgap fiber based on a square lattice cladding. The fiber presents a 20% wider bandgap than is achievable with a conventional triangular-lattice-based cladding and with the choice of a nine-cell core can be effectively single moded at all wavelengths within the bandgap.

X-band continuously variable true-time delay lines using air-guiding photonic bandgap fibers and a broadband light source

We propose a novel implementation of true-time delay (TTD) using air-guiding photonic bandgap fibers (PBGFs) and a broadband light source. The air-guiding PBGFs are experimentally studied and used in the TTD module for the first time, to the best of our knowledge. The proposed approach shows the advantages of simple architecture, compact size, larger dispersion, low-temperature sensitivity, and high immunity to nonlinear effects in our experiments. The PBGFs were spliced with single-mode fibers with a 2 dB loss, and the characteristics of the PBGFs were measured. The PBGF-TTD with a continuously tunable time delays from 0 to 500 ps was demonstrated using the amplified spontaneous emission light of an erbium-doped filter amplifier as a broadband light source.

Realization of single-moded broadband air-guiding photonic bandgap fibers

In this letter, we propose a novel type of air-guiding photonic bandgap fiber, which exhibits an effectively single-mode operation with a low confinement loss over a wide wavelength range, extended from 1460 to 1840 nm. For several realistic structural parameters, the wavelength dependence of the dispersion as well as the confinement loss properties are investigated through a full-vector modal solver based on the finite-element method. In particular, we optimize the structure so as to exhibit the following performance: effectively single-mode operation from 1460 to 1840 nm, with corresponding confinement loss of the fundamental air-guided mode of 8.8times10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-5</sup> dB/km, and enhancement of the confinement loss of the higher order mode of 43 dB/m for ten-ring structure

Demodulation of DPSK signals up to 40 gb/s using a highly birefringent photonic bandgap fiber

Phase-to-intensity modulation conversion of differential phase-shift keying signals is successfully demonstrated at 10 and 40 Gb/s using a polarization Mach-Zehnder delay interferometer implemented with only 2.4 m of a highly birefringent air-guiding photonic bandgap (PBG) fiber. Such a PBG fiber exhibits a birefringence one order of magnitude larger than that of conventional polarization-maintaining fibers, thus enabling the realization of compact interferometers. Furthermore, its single material nature is expected to result in reduced temperature sensitivity.

Confinement loss and nonlinearity analysis of air-guiding modified honeycomb photonic bandgap fibers

Air-guiding photonic bandgap fibers based on a modified honeycomb lattice have been numerically investigated through the finite element method. Results confirm that an extra hole in the unit cell of a honeycomb lattice can be exploited to enlarge the photonic bandgap, allowing air-guiding with confinement losses lower than 0.1 dB/km and nonlinear coefficient lower than 3.5middot10-3(Wmiddotkm) -1 at 1.55 mum

Improved air–silica photonic crystal with a triangular airhole arrangement for hollow-core photonic bandgap fiber design

We propose an improved photonic crystal (PC) cladding design for existing air-guiding photonic bandgap (PBG) fibers whose cladding airholes are arranged in a triangular lattice pattern. By increasing the sizes of concentrated silica regions in the cladding PC, we can have a larger degree of freedom in controlling the cladding bandgap regions. We predict that a fiber made from this type of cladding would perform better in terms of the PBG-guiding wavelength range, radiation loss owing to finite cladding size, and the ability to avoid surface mode problems.

Gas filled photonic bandgap fibers as wavelength references

We demonstrate that air-guiding photonic bandgap fibers filled with various gases, such as acetylene and methane provide optical wavelength references. The constructed devices are compact and cost-effective.

Phase sensitivity to temperature of the fundamental mode in air-guiding photonic-bandgap fibers

Because in an air-core photonic-bandgap fiber the fundamental mode travels mostly in air, as opposed to silica in a conventional fiber, the phase of this mode is expected to have a much lower dependence on temperature than in a conventional fiber. We confirm with interferometric measurements in air-core fibers from two manufacturers that their thermal phase sensitivity is indeed ~3 to ~6 times smaller than in an SMF28 fiber, in agreement with an advanced theoretical model. With straightforward fiber design changes (thinner jacket and thicker outer cladding), this sensitivity could be further reduced down to ~11 times that of a standard fiber. This feature is anticipated to have important benefits in fiber optic systems and sensors, especially in the fiber optic gyroscope where it translates into a lower Shupe effect and thus a greater long-term stability.

Air guiding with honeycomb photonic bandgap fiber

We notice that honeycomb cladding was overlooked for air-guiding photonic bandgap fiber design. Air-silica honeycomb cladding is shown in this letter to be able to guide light in a slightly large-sized hollow core, with a reasonably wide bandwidth (/spl sim/200 nm). Noncircular air-hole shape is also explored for air-guiding honeycomb fiber design.

Gas sensing using air-guiding photonic bandgap fibers

We demonstrate the high sensitivity of gas sensing using a novel air-guiding photonic bandgap fiber. The bandgap fiber is spliced to a standard single-mode fiber at the input end for easy coupling and filled with gas through the other end placed in a vacuum chamber. The technique is applied to characterize absorption lines of acetylene and hydrogen cyanide employing a tunable laser as light source. Measurements with a LED are also performed for comparison. Detection of weakly absorbing gases such as methane and ammonia is explored.

All fiber chirped-pulse amplification system based on compression in air-guiding photonic bandgap fiber

We report on the experimental demonstration of an all fiber CPA system based on a step-index fiber stretcher and an air-guiding photonic crystal fiber compressor. The ultrafast fiber laser system producing an average power of 6.0 W with 100-fs pulses at 73 MHz, what corresponds to a peak power out of the compressor fiber of 0.82 MW. This completely fiber integrated approach has the potential to be scaled to significantly higher peak powers.

Material effects in air-guiding photonic bandgap fibers

The waveguiding properties of two silica-based, air-guiding photonic bandgap fiber designs are investigated with special emphasis on material effects. The nonlinear coefficients are found to be 1–2 orders of magnitude smaller than those obtained in index-guiding microstructured fibers with large mode areas. The material dispersion of silica makes a significant contribution to the total chromatic dispersion even though less than 10% of the field energy is located in the silica regions of the fibers. These findings suggest that dispersion engineering through the choice of base material may be a possibility in this type of fiber.

Confinement losses in air-guiding photonic bandgap fibers

The wavelength dependence and the structural dependence of confinement losses in air-guiding photonic bandgap fibers (PBGFs) are, for the first time, investigated by using a full-vector finite element method. It is confirmed from computed results that one of the main causes of transmission losses in air-guiding PBGFs is the confinement loss and that, even if using large air holes of diameter to pitch ratio of 0.9, at least twenty rings of air hole arrays are required in the cladding region to reduce the confinement loss to a level of 0.01 dB/km.

Analysis of air-guiding photonic bandgap fibers

We present what is to our knowledge the first theoretical analysis of air-guiding photonic bandgap fibers. The fibers are characterized by a large hollow core and a microstructured cladding exhibiting photonic bandgap effects. Using an efficient, full-vectorial numerical method, we explain the operational principle of the fibers and obtain detailed information about the properties of the air-guided modes. This information includes accurate determination of the modes' spectral extent, cutoff properties, and mode-field distributions.