Adsorbent For Removal Of Heavy Metals Research Articles

Assessing the life cycle and economic impact of cement-modified biochar compared to conventional adsorbents for heavy metal removal in stormwater

Modified biochar is used for heavy metal removal from stormwater, but current modifications rely on high-cost chemicals and result in highly toxic effluents. Additionally, there is limited research on these modifications' environmental impact and cost. This study aims to investigate the life cycle analysis (LCA) and economics of the process of absorption of Cu, Pb and Zn from synthetic stormwater utilizing cement-modified biochar adsorbent and compared it with commonly available adsorbents, activated carbon and zeolite. The cradle-to-gate LCA used experimental data and the Ecoinvent 3.0 database. Adding 1.5 % cement to biochar reduced its negative environmental impact by two to three times compared to plain biochar. Cement addition enhances heavy metal removal by raising pH, promoting precipitation, and reducing metal mobility. Combined with biochar, it increases the available surface area for adsorption, further boosting the system's efficiency in contaminant removal. The cement-modified biochar had the lowest global warming potential (kg CO2 eq), about half of Paddy Husk Biochar (PHBC). Approximately 50–90 % of the environmental impact of cement-modified biochar, zeolite, and PHBC was attributed to raw material collection. The Saw Dust Biochar (SDBC) had the highest sensitivity towards transportation distances among the adsorbents considered. Due to its heightened adsorption capacity, the 98.5 % PHBC composite demonstrated the lowest environmental impacts for Cu and Zn removal in multi-metal systems. Transportation of raw materials and labor costs were the primary cost drivers for biochar-based adsorbents. Among the adsorbents, 98.5 % PHBC was the best, being cost-effective and efficient for heavy metal removal. It is suitable for at-source pollutant removal in low-rainfall and high-pollution areas. Overall, this study helped identify performance weaknesses and modification opportunities for cement modification of biochar in heavy metal pollution control.

Green synthesis of nano silver-modified date syrup 3D graphene for adsorptive removal of heavy metals from wastewater and its antibacterial efficiency

Abstract Many researchers are focusing on the eco-friendly and cost-effective green synthesis of materials for removing heavy metals from wastewater using materials made from natural sources. In this research, date syrup was used as a rich carbon source while potassium chloride particles were used as a substrate. Green synthesized silver nanoparticles modified the graphene foam to enhance its heavy metal removal and antibacterial efficiency. The morphology and structure of the graphene foam were examined using scanning electron microscopy and Raman spectroscopy. The Brunauer-Emmett-Teller method examines textural features such as surface area, pore volume and diameter. The study focused on evaluating the efficiency of removing heavy metals including cadmium, lead, zinc, and chromium from water. The results indicated that the date syrup graphene foam has high heavy metal removal efficiency despite the short contact time, especially for Cd2+ and Pb2+, with removal efficiencies of 68% and 39%, respectively. It shows a relatively lower efficacy for Zn2+ and Cr2+, with removal efficiencies of 10% and 27%, respectively. The addition of silver nanoparticles greatly improved the removal efficiency of Cd2+ (75%), Zn+2 (22%), and Cr2+ (33%). Moreover, the antibacterial efficacy test showed significant improvement after the nanosilver modification to reach a 100% bacterial-killing rate.

Green synthesis of CaO nanoparticles from chicken eggshells: antibacterial, antifungal, and heavy metal (Pb2⁺, Cr2⁺, Cd2⁺ and Hg2⁺) adsorption properties

BackgroundChicken eggshells, a common poultry byproduct, are rich in calcium and provide a sustainable source for producing calcium oxide nanoparticles (CaO NPs). Their use in eco-friendly synthesis aligns with the growing emphasis on sustainable materials for environmental and biomedical applications. Objectives: This study develops an eco-friendly method for synthesizing CaO NPs from chicken eggshells, characterizes their physicochemical properties, and evaluates their antibacterial and antifungal activities. It also tests their effectiveness in removing heavy metal ions (Pb2⁺, Cr2⁺, Cd2⁺, and Hg2⁺) from aqueous solutions.MethodsCaO NPs were synthesized by calcining chicken eggshells at 700°C for 7 h. Comprehensive characterization included analysis of crystalline structure, morphology, optical properties, bandgap energy, chemical composition, and thermal stability. Antibacterial and antifungal activities were tested using the well-agar diffusion method. Batch adsorption experiments evaluated heavy metal ion removal under varying conditions of pH, temperature, stirring time, and adsorbent concentrationResultsThe synthesis produced spherical, single-crystal CaO NPs with diameters ranging from 5 to 30 nm and a crystalline size of approximately 20 nm. The nanoparticles had a bandgap energy of about 4.7 eV. Significant antibacterial activity was observed against Staphylococcus aureus, Klebsiella pneumoniae, and Escherichia coli, with increasing inhibition zones correlating with nanoparticle concentration. The CaO NPs also effectively inhibited Candida albicans. For efficient metal ion removal, the optimal conditions were found to be 30 min at pH 6 with 40 mg of CaO NPs at 25°C, achieving recovery rates of 98% for Pb2⁺, 97% for Cd2⁺, 97% for Cr2⁺, and 97% for Hg2⁺. For near-complete removal, extending the process to 70 min at pH 6 with 40 mg of CaO NPs at 45°C achieved the highest recovery rates: 99% for Pb2⁺, 98% for Cd2⁺, 99% for Cr2⁺, and 99% for Hg2⁺, though this approach involves higher energy and cost.ConclusionCaO NPs derived from chicken eggshells are effective antibacterial agents and adsorbents for heavy metal removal. These findings highlight their potential for sustainable applications in environmental and biomedical fields.

Biochar-based adsorption for heavy metal removal in water: a sustainable and cost-effective approach.

The increasing contamination of aquatic bodies by heavy metals poses a significant threat to environment and human health, necessitates innovative, sustainable and cost-effective remediation strategies. Due to their persistence and toxicity, heavy metals like copper (Cu), lead (Pb), mercury (Hg), and cadmium (Cd) pose severe threats, even in trace amounts. Traditional removal methods of these heavy metals, like chemical precipitation, oxidation/reduction, filtration, ion exchange, membrane separation, and adsorption, are costly, inefficient, and have drawbacks. As an efficient and low-cost adsorbent, biochar has the potential for heavy metal remediation from water. Biochar is a versatile carbonaceous material produced through pyrolysis of organic wastes, emerged as a powerful adsorbent for heavy metal removal from contaminated water. The unique property of biochar makes it an effective medium immobilizing and capturing of heavy metals like Pb, Cd, As and Hg. Various factors affect its adsorption potential and capacity. Feedstocks type, composition, activation methods, and production processes including the pyrolysis temperature, temperature rate and residence time significantly impact the efficacy of biochar. Therefore, this review has assessed, compared, and contrasted different forms of biochar along with their production methods, modification techniques and mechanisms for their potential use as an adsorbent for heavy metal removal from the contaminated water. Modified biochar offers an environmentally friendly and cost-effective solution for water purification and remediation of toxic heavy metals from water. This review highlights the biochar potential as a crucial component for future research projects focusing on water treatment technologies, providing avenues for safer and cleaner water resources.

Modified Cellulose-Based Waste for Enhanced Adsorption of Selected Heavy Metals from Wastewater.

Due to industrial growth and its impact on the environment, the increasing amount of industrial waste requires a comprehensive approach aligned with the principles of sustainable development. The main goals are not only to preserve natural resources but also to encourage innovation in the reuse of waste materials. In an attempt to reduce the problems regarding waste disposal and wastewater treatment in the textile industry, fibrous textile waste was used as a starting material to obtain carbon adsorbents for the removal of pollutants from wastewater. Waste cotton and mixed yarns, mainly consisting of polysaccharide cellulose, were hydrothermally carbonized and activated with KOH to convert them into efficient carbon adsorbents for heavy metal removal from water. Characterization of carbonized material showed that after activation, an increase in specific surface area (up to 872 m2/g) and content of surface oxygen groups (6.04 mmol/g) leads to a higher affinity towards heavy metal ions, especially lead ions, and high adsorption capacity of 19.98 mg/g obtained for activated cotton yarns. The results of this research represent a contribution to the reduction of waste materials by modifying them into adsorbents, while the regeneration of adsorbents is an example of the practical application of polysaccharide-based materials in the purification of wastewater containing various heavy metal ions.

Role of nanocomposites and nano adsorbents for heavy metals removal and dyes. An overview

Water scarcity and wastewater treatment are major concerns due to increased urbanization, industrialization, and anthropogenic practices. Various toxic heavy metals, dyes, pollutants, and chemicals are a matter of concern as they have severe environmental and ecological damage and health effects. Various advancements are being introduced in the field of adsorption using nano adsorbents and composites to deal with wastewater treatment problems. Nanocomposites are intelligent to eliminate bacteria, viruses, and inorganic and organic pollutants from wastewater due to precise binding action (chelation, absorption, ion exchange). Nanocomposite materials, such as metal nanocomposite, metal oxide nanocomposite, carbon nanocomposite, polymer nanocomposite, and membrane nanocomposite, are active in water purification. Nanoparticles (N.P.s) are important for remediation because of their large surface area, size, reactivity, and active sites. For high adsorption of pollutants, N.P.s were treated by increasing the electron density and surface area and adding functional groups. They are more capable of eliminating hazardous organic-inorganic pollutants, pathogens, and heavy metals from wastewater. This nanotechnology treatment technique has no hazardous by-products; these techniques have various regenerative efficiencies. Among various treatment methods, the adsorption process is considered one of the most highly effective treatments of heavy metals, and the functionalization of adsorbents can fully enhance the adsorption process. Therefore, four adsorbent sources are highlighted: polymeric, natural mineral, industrial by-product, and carbon nanomaterial adsorbent. The major purpose of this review is to gather up-to-date information on research and development on various adsorbents in the treatment of heavy metal and dyes from water by emphasizing the adsorption capability, the effect of pH, isotherm and kinetic model, removal efficiency, and the contact of time of every adsorbent.

From agricultural wastes to advanced materials for environmental applications: Rice husk-derived adsorbents for heavy metals removal from wastewater

Agroindustry annually generates enormous amounts of residues, and their re-utilization is a convenient approach to mitigate environmental pollution and increase energy savings. Rice husk (RH) is one of the most widely available agricultural wastes in many countries of the world. RH and its ashes are often used directly for manufacturing and synthesizing new materials with added-value features. In this work, the preparation of composite materials for wastewater treatment has been explored by producing and testing mesoporous iron-oxide/RH composites for heavy metal adsorption. The composites were fully characterized and their application to the removal of Pb2+ and Cu2+ ions from model aqueous solutions at different pH values was tested to evaluate their adsorption performances and select those materials more suited for realistic applications. Our results indicated that the composite materials exhibited higher metal adsorption capacities than the pristine carbonized RH and the iron components, highlighting a synergism between the carbonized RH and iron-oxide phases.

Synthesis and characterization of thiazolidinone -functionalized MCM-41 and kaolinite nanocomposites as the powerful and new adsorbents for heavy metal removal: process optimization using RSM-CCD

Synthesis and characterization of thiazolidinone -functionalized MCM-41 and kaolinite nanocomposites as the powerful and new adsorbents for heavy metal removal: process optimization using RSM-CCD

Investigation of the potential of pomegranate peel as a treatment option for heavy metal contaminated wastewater: Experimental and modeling approaches

Heavy metals can cause serious environmental and human health problems, and their removal from wastewater is critical to protect our planet and communities. This study investigated the ability of crushed pomegranate peel to remove mercury and cadmium ions from contaminated water as a function of different experimental parameters. The experimental results showed that the pH of the solution influenced the adsorptive removal of heavy metals, with the best performance observed at pH 4.8. Optimization studies and process balance modeling were performed to optimize the process for commercial use. The performance of pomegranate peel was compared with that of other materials, and the highest adsorption capacities for both cadmium (Ca (II)) and mercury (Hg (II)) ions were observed to be 89.59 and 42.125 mg/g, respectively. The results were interpreted using the Langmuir model, which provided the best fit to describe the behavior of the process.

Investigation of regeneratable biopolymer-based aerogels for heavy metal decontamination from water: Quantum chemical analysis and experimental investigation

Heavy metals pose a significant threat to human health and ecological security due to their high toxicity, mobility, and persistence in the environment. Herein, the synthesis of a novel cellulose nanofiber-based aerogel using non-toxic biopolymers such as sodium alginate and polyglutamic acid to eradicate lead, zinc, and copper from water is described. The physical characterisation and the adsorption performance of the aerogels were evaluated in both monolithic and bead configurations. The study revealed superior adsorption performance for the aerogel beads compared to the monolithic configuration. The aerogel beads achieved a maximum adsorption capacity of 171.7 mg/g, 100.0 mg/g, and 142.0 mg/g for lead, zinc, and copper respectively. The aerogel beads exhibited a higher specific surface area compared to the monolithic aerogels. The presence of functional groups including carboxyl, amino, and hydroxyl groups on the aerogels likely facilitated the adsorption through coordinate bond formation and electrostatic interactions. Density Functional Theory calculations supported the role of oxygen and nitrogen containing groups on the aerogel in capturing heavy metal ions. The aerogels displayed a remarkable regeneration ability and were reused 20 times, without any significant reduction in the adsorption performance indicating its potential as a sustainable adsorbent for heavy metals removal from water.

Exploring biosynthesis strategies to boost the yield of exopolysaccharide-protein blend from Bacillus arachidis SY8(T), an isolated native strain, as a potent adsorbent for heavy metals removal

This investigation centers on the synthesis of a polysaccharide-protein blend produced by an isolated native strain (99.12 % phylogenetic affinity with Bacillus arachidis SY8(T)). The primary objective was to investigate the production of extracellular polymeric substances (EPS) under diverse stress conditions, encompassing exposure to heavy metal ions, salt, and toxic agents. Additionally, the impact of environmental parameters, namely pH, inoculation percentage, and time, on the production was investigated. Subsequently, the study examined the biosorption potential of the EPS produced for Pb(II), Cu(II), and Mn(II). The EPS obtained was thoroughly characterized via various tests. Rheological evaluations of an EPS solution (2 wt%) confirmed its pseudo-plastic and non-Newtonian fluid properties, while TGA analysis demonstrated its thermal stability up to 600 °C. Additional analyses, including GPC, FTIR, and H-NMR, provide further insights into the produced EPS. The best conditions for EPS production are determined: 5 % NaCl salt, serving as an effective stress inducer, and 37 °C, pH 6, with a 5 % inoculation, over 96 h. EPS demonstrates remarkable removal efficiencies of 99.9, 99.4 and 78.9 % for Pb(II), Cu(II), and Mn(II), respectively. These findings highlight the potential of EPS as an effective agent for removing heavy metal ions.

Optimizing enhanced heavy metal detoxification by novel hybrid fungal hyphae-nano-biocomposite functionalized with graphene oxide: Unravelling process parameters & adsorption modelling

Heavy metal pollution poses significant environmental and health risks, demanding efficient novel remediation strategies. This paper presents a fungal hyphae-based nano-biocomposite integrated with graphene oxide (FHGO) for the efficient removal of heavy metals from aqueous solutions. The successful formation of nanoparticles was investigated by morphological characterization using Fourier Transform Infrared Spectroscopy (FTIR), Scanning electron microscopy (SEM) & X-ray diffraction (XRD). Through comprehensive exploration of process parameters, including pH, initial concentration, and contact time, the nano-biocomposite demonstrated exceptional removal efficiencies exceeding 90% for both heavy metals i.e. chromium (Cr6+) & nickel (Ni2+). The optimum pH conditions for Cr (VI) removal was 4,whereas it was 9 for Ni (II) removal. The equilibrium data were well-fitted to Langmuir isotherm models, suggesting monolayer adsorption onto a homogeneous surface with adsorption capacities of 38.89 mg/g & 42.88 mg/g for Ni (II) & Cr (VI), respectively, with value of R2=0.997. Additionally, biocompatibility assessments via (3-(4,5-dimethylthiazolyl-2)-2,5-diphenyltetrazolium bromide) MTT assays on Henrietta Lacks (HeLa) cell line cultures revealed a low IC50 value of FHGO nano-biocomposite, affirming the efficiency of the composite for biomedical applications. Furthermore, seed germination assays indicated comparatively minimal hindrance to plant growth in the treated sample, highlighting the composite's potential for environmental remediation without compromising plant health. These findings underscore the promising potential of the fungal hyphae-based nano-biocomposite with GO as an effective and environmentally safe adsorbent for heavy metal removal, with implications for sustainable environmental management and public health protection.

Cd2+ removal efficiency of activated carbon from Prosopis juliflora: Optimization of preparation parameters by the Box-Behnken Design of Response Surface Methodology

The study focuses on the preparation of activated carbon from Prosopis juliflora (PJAC) wood by pyrolysis and chemical activation. The objective is to assess its effectiveness as an adsorbent for synthesizing a composite adsorbent coating (CAC) for Cadmium (Cd2+) removal from aqueous solution. The effect of preparation factors related to Cd2+ removal efficiency was assessed. The Design of Experiments (DoE) for the adsorption of Cd2+ on the PJAC were done using the Box-Behnken Design (BBD) of the Response Surface Methodology (RSM) (Design Expert software version 11). The influence of impregnation ratio (IR), carbonization time (t), and carbonization temperature (T) on the Cd (II) percent (%) removal was evaluated. The response surface graphs in 3D were also generated for the response variable, and the higher R2 coefficient values were fitted into the polynomial quadric model. The results indicated that all the variable preparation factors were significant in the Cd2+ removal by PJAC with carbonization temperature being the most significant. At the optimum conditions i.e. impregnation ratio (1.8), carbonization temperature (595 °C) and carbonization time (174 min), the model predicted a 99.9 % Cd2+ removal efficiency while the adsorption experiment obtained a 96.7 % removal efficiency, respectively. Later, the morphological and chemical properties of the PJAC prepared with optimal parameters were analyzed using different characterization techniques including SBET, SEM-EDX, pHPZC, FTIR and XRD. The SEM images revealed a rough and porous morphological surface with an SBET of 600.4 m2/g and a near neutral pHPZC of 6.92. The XRD pattern indicated the crystalline nature of the prepared adsorbent. The pre and post adsorption FTIR spectrum of the PJAC demonstrated a distinct difference with the latter showing a reduction in peak intensity and height. These results underpin the potential of utilizing invasive plants like Prosopis Juliflora as adsorbents for heavy metal removal.

Production of Modified Zeolites from Rice Husk Ash for Removal of Cadmium from Aqueous Solution

In this study, ZSM-5 zeolite from rice hush ash (RHA) was synthesized and modified to assess the removal of cadmium from aqueous solution using standard methods. Both the synthesized and modified ZSM-5 were characterized using XRD, SEM TEM, FTIR and BET. Presence of silicate in the RHA was confirmed with XRF to contain 86.85% silicate. Batch experiments of the adsorption carried out with specific concentration of cadmium shows that both the synthesized and modified zeolites demonstrated 44% and 78% cadmium ions removal from the simulated solution respectively. The study concluded that synthesized and modified ZSM-5 zeolites are highly efficient adsorbent for heavy metal removal.

Evaluating the performance of cement-modified biochar adsorbent for Cu, Pb and Zn removal from urban stormwater

This research investigates the use of biochar modified with Ordinary Portland Cement (OPC) as an adsorbent for heavy metal removal and evaluates the impact of competing ions and nutrients on the adsorptive removal process. The cement-modified biochar composites, featuring functional groups from biochar and hydrated OPC, exhibited significantly enhanced adsorption capacities for Cu, Pb, and Zn, approximately 3.3, 2.4, and 6 times higher, respectively, compared to unmodified biochar upon introducing 1.5 % (v/v) OPC. The Langmuir monolayer adsorption model accurately described the adsorption data, with heavy metals binding to functional groups like CC and CO, CO3–2, silanols (Si-OH), siloxanes and calcium silicate hydrate. The cement-modified biochar composite exhibited notable adsorption capacities for Cu, Pb, and Zn at 28.82 mg/g, 38.76 mg/g and 26.53 mg/g, comparable to commercial activated carbons. There were negligible effects from NO3- on the removal of Cu, Pb and Zn, PO43- ions enhanced Pb removal, and NH4+ ions slightly reduced the removal of all three metals, while humic acid increased removal. The findings indicate that using OPC boosts heavy metal adsorption, and insights into the influence of competing ions and nutrients apprise strategies for using OPC-modified biochar in practical applications.

Facile Synthesis of Sodium Dodecyl Sulfate Intercalated Mg‐Al LDH and its Excellent Adsorption Performances for Cu2+ from Aqueous Solution

AbstractIn this study, the magnesium aluminum layered double hydroxide intercalated with sodium dodecyl sulfate (Mg‐Al S‐LDH) was synthesized by using a roasting–restoration method based on the Mg‐Al LDH precursor, and their effectiveness in removing Cu2+ from aqueous solutions was investigated. Detailed microstructural characterization of these adsorption materials involved employing X‐ray diffraction (XRD), Fourier‐transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen adsorption/desorption isotherms (N2 ad/desorption), and thermogravimetric‐differential thermal gravimetric analysis (TG‐DTG). The experimental results revealed that Mg‐Al S‐LDH displayed a plate‐like layered structure with a larger surface area and enhanced adsorption ability. Specifically, the maximum adsorption capacity, reaching 96.15 mg ⋅ g−1, was achieved at a temperature of 298 K, accompanied by a rapid adsorption rate. The adsorption kinetics adhered to the pseudo‐second‐order model, suggesting that chemisorption controlled the adsorption behavior. Furthermore, the adsorption of Cu2+ followed the Freundlich model, signifying a multi‐site adsorption mechanism onto the surface and layers of Mg‐Al S‐LDH. Thermodynamic investigations indicated that higher temperatures facilitated Cu2+ dissolution and strengthened the affinity with Mg‐Al S‐LDH, with a positive ΔHΘ value suggesting that the Cu2+ adsorption process was endothermic and temperature‐enhancing. Ion selectivity experiments demonstrated that Cd2+ and Pb2+ ions had a significant impact on Cu2+ adsorption, while the effects of Zn2+ and Fe2+ ions were less pronounced. The primary adsorption mechanisms of Cu2+ onto Mg‐Al S‐LDH encompassed precipitation, complexation on the surface and layers, and isomorphous substitution. This study sheds light on the promising potential of Mg‐Al S‐LDH as an effective adsorbent for heavy metal removal and provides valuable insights into its adsorption mechanisms and performance in different environmental conditions.

Investigation of adsorptive removal of heavy metals onto magnetic core–double shell nanoparticles: kinetic, isotherm, and thermodynamic study

The most perilous environmental hazards arise from the contamination of water by heavy metal ions, owing to the non-biodegradability of these metals, as well as their rapid dissemination throughout components of the environment via the food chain. Nano-based adsorbents have been used for the adsorption removal of many heavy metal cations, but separating and recycling them represent significant difficulties in processing. Magnetic core–double shell nanoparticles provide an attractive solution for processing issues, since they are stable and can be easily separated and recycled. Moreover, the shell thickness, composition, and porosity can be easily tuned. In this work, two samples consisting of magnetic core@TiO2@mesoSiO2 nanoparticles with two shell thicknesses (Mag-T-S-0.2 and Mag-T-S-0.4), along with a magnetic core@SiO2@TiO2 nanoparticle sample (Mag-S-T), were synthesized and characterized by TEM, XRD, magnetic strength measurement and zeta potential. TEM images show the developed core–double shell structure with double shell ranging from 60 to 73 nm. The XRD results indicate the impact of the outer shell on the diffraction pattern. The zeta potential shows that all samples had a negative charge at pH over 4. The magnetic character was suppressed after the formation of the double-shell coating; however, the magnetic core–double shell nanoparticles still had magnetization and could be separated when an external magnetic field was applied. The heavy metal adsorptive ability of Mag-T-S-0.2, Mag-T-S-0.4, and Mag-S-T samples was explored to investigate the effects of shell type and thickness along with kinetic, isotherm, and thermodynamic study. The investigated heavy metals included Cd(II), Ni(II), Mn(II), Pb(II), and Cu(II). The results indicate that, for Mag-T-S-0.2, the equilibrium state occurred after 15 min contact time, with adsorption capacity of 238, 230, 210.6, 181.8, and 245.8 mg/g for Cd(II), Ni(II), Mn(II), Pb(II), and Cu(II), respectively. For Mag-T-S-0.4, the equilibrium state occurred after 15 min contact time, with adsorption capacity of 241, 237.6, 173.8, 189.6, and 257.2 mg g−1, respectively. For Mag-S-T, the equilibrium state occurred after 25 min contact time, with adsorption capacity of 137.8, 131.4, 221, 189.6, and 149.4 mg g−1, respectively. When pseudo-first-order and pseudo-second-order kinetic models were applied to investigate the time interval adsorption data for Mag-T-S-0.2, Mag-T-S-0.4, and Mag-S-T samples, the second-order kinetic model was found to be more suitable for describing the process, indicating a fast adsorption mechanism. The adsorption data did not fit well with the Langmuir model, while they did fit well with the Freundlich model, suggesting heterogeneous material surfaces and multi-layer adsorption. Thermodynamic investigations confirmed the spontaneous nature of adsorptive removal, which helps to promote magnetic core@TiO2@mesoSiO2 and magnetic core@SiO2@TiO2 nanoparticles as effective adsorbents for wastewater treatment.

Cation Effect in Polysaccharide-Based Hydrogel Beads Produced for Europium Adsorption from Aqueous Solutions

In recent decades, renewable and biodegradable polysaccharide-based hydrogels have enjoyed wide applicability among them also as adsorbents for heavy metal removal from wastewaters. Herein we prepared hydrogel beads from iota and kappa carrageenans using a variety of salts as crosslinkers, that were tested for the first time in europium ion (Eu3+) sorption from an aqueous solution as representative lanthanide. The type of the salt, and especially the valance and the hydrated radius of the cation, were found to dictate hydrogel bead formation and structure and, therefore, the Eu3+ sorption yield. The results of ATR-FTIR, SEM and TGA analyses to characterize the iota carrageenan hydrogel beads that were prepared with alkali cations, before and after interaction with Eu3+, indicate that the adsorbent prepared with LiCl was much stiffer and more stable than those prepared with NaCl or KCl. The iota carrageenan beads that were prepared with LiCl were also reused 5 times while exhibiting high adsorption capacities.

ADSORTION POTENTIAL OF GARLIC, GINGER AND LEMON IN THE REMOVAL OF HEAVY METALS FROM AQUEOUS SOLUTIONS

This work was conducted to assess the efficiency of Garlic, Ginger and Lemon in the removal of some Heavy Metals from aqueous solution. Batch adsorption process was employed in the experiments. Different dosages (0.2, 0.4, 0.6, 0.8 and 1.0) g of the adsorbents and concentrations of the heavy metals (1000ppm, 800ppm, 600ppm, 400ppm, and 200ppm) were prepared and used. Flame Atomic Absorption Spectroscopic (FAAS) was used to determine the amount of heavy metal concentrations adsorbed at each stage of the experiment. Results obtained show that there was remarkable reduction of metal concentrations in the solutions. However, comparatively, the efficiency of garlic in absorbing the metals is greater than that of ginger and lemon at all conditions. Thus, results obtained suggest that Garlic, Ginger and Lemon could be promising adsorbents for heavy metal removal in aqueous solutions, but garlic has greater efficiency in adsorbing the metals particularly zinc and copper.

Wastewater Treatment Utilizing Industrial Waste Fly Ash as a Low-Cost Adsorbent for Heavy Metal Removal: Literature Review

Wastewater discharges from industrial processes typically include elevated concentrations of contaminants, which largely consist of potentially harmful chemicals such as heavy metals. These contaminants are characterized by their slow rate of decomposition. Hence, the removal of these metallic ions from effluents poses a challenge. Among different treatments, the adsorption approach has considerable potential due to its ability to effectively eliminate both soluble and insoluble pollutants from effluent, even at lower levels of concentration. Of various wastes, fly ash (FA) material has been the subject of attention because it is abundant, has favorable qualities, and contains a high percentage of minerals. This review investigates multiple facets, with a specific focus on the application of FA, an industrial byproduct, as an adsorbent in removing heavy metals. A comprehensive examination was conducted on a range of concerns pertaining to the pollution caused by metallic ions, including the underlying causes, levels of contamination, health implications of heavy metals, and removal methods. Multiple factors were found to affect the adsorption process. Of all the factors, the pH value considerably influences the elimination of heavy metals. An acidic pH range of 2.5–4.5 was found to be optimal for achieving the highest possible elimination of As(V), Cu(II), Hg(II), and Cr(VI). The latter elimination rate reached 89% at the optimal pH level. Most heavy metals’ adsorption isotherms conformed to the Langmuir or Freundlich models, while the pseudo-second-order kinetics provided a satisfactory match for their removal. Using a raw FA, adsorption capacities were achieved in the removal of metallic ions, Ni(II), Pb(II), and Cr(VI), that ranged from 14.0 to 23.9 mg g−1. Meanwhile, the FA-zeolite showed a remarkable capacity to adsorb ions Mn(II), Ni(II), Cd(II), Cu(II), and Pb(II), with values ranging from about 31 to 66 mg g−1. The cost analysis showed that the treatment of FA is economically advantageous and may result in significant cost reductions in comparison to commercial adsorbents. In summary, FA is an inexpensive waste material with potential for water treatment applications and several other purposes due to its excellent chemical and mineralogical composition.