Adhesive Fracture Research Articles

Comparison of the microtensile bond strength of direct and indirect resin restorations in the cervical region

ObjectivesTo evaluate in vitro the adhesion system of direct and indirect composite resin restorations in enamel and dentin, in cavities made in the cervical region using microtensile bond strength (μTBS) and to observe the most recurrent types of failure in the different groups. MethodsStandardized cavities were made in the line of the cementoenamel junction (CEJ) in 36 selected human premolars, which were randomly divided into 2 groups. In the Indirect Restorations (IR) group, indirect restorations were cemented in composite resin, using a universal adhesive and dual resin cement, performing selective enamel etching (SEE). In the Direct Restorations (DR) group, direct restorations were made in composite resin, performing SEE and bonding with the universal adhesive. Each specimen was sliced into sections measuring approximately 1 mm2, with enamel and dentin adhesion divided into subgroups DRe, DRd, IRe, and IRd. The sections were subjected to the μTBS test to assess bond strength in both enamel and dentin, comparing direct and indirect restorations in the cervical region. The types of failure in each group were also observed. ResultsThere was no statistically significant difference in μTBS between the DRe and IRe groups (p = 0.314) and also between the DRd and IRd groups (p = 0.145). There was a predominance of adhesive failures. ConclusionsThe bond strength of composite resin restorations was found to be equivalent in enamel and dentin, whether applied directly or indirectly. There was a predominance of adhesive fractures followed by cohesive resin fractures. Clinical significanceThe choice between direct and indirect restorations in the cervical region may consider patient preferences, but with caution, as clinical factors such as operator skill, specific tooth conditions and case complexity are crucial, and both techniques exhibit comparable bond strength.

Adhesive and cohesive fracture of blood clots: Experiments and modeling

Blood clots represent living materials composed of a polymer network and an abundance of cells. They might fracture within the bulk material of the clot (cohesive fracture), at the interface between the clot and the surrounding tissue (adhesive fracture), or through a combination of both modes (hybrid fracture). The clot fracture within vascular systems and injury sites could lead to life-threatening conditions. Despite the significance, understanding and modeling the fracture behaviors of blood clots, including their dependence on mechanical loading and cellular components, remain in a nascent stage. In this study, we employ an integrated experimental-computational approach to comprehensively investigate the fracture behaviors of bovine blood clots. We explore various mechanical factors, substrates, and cellular components such as red blood cells (RBCs) and platelets. Our findings reveal that among various tissue substrates, blood clots exhibit the highest interfacial adhesion energy with muscle, and the lowest to the inner arterial lining, consistent with their biological function. Both interfacial adhesion energy and bulk fracture energy are rate-dependent, although they exhibit different dependencies. Also, RBCs and platelets have different effects on clot fracture. An increase in RBC content tends to toughen both adhesion and fracture of blood clots. However, an increase in platelet content enhances interfacial adhesion energy but lowers the bulk fracture energy. The platelet content also governs the shift from adhesive fracture to hybrid fracture. To model clot fracture, we developed two finite element models incorporating a coupled cohesive-zone and Mullins-effect approach to simulate pure shear fracture and peeling of blood clots. These models, validated through experimental data, elucidate the interplay between intrinsic fracture toughness, interfacial strength, and bulk energy dissipation during clot fracture. This study significantly advances our understanding of clot mechanics, providing valuable insights into the mechanics of similar living materials and the management of clot-related disorders such as hemorrhage and thrombosis.

Effect of different chelators on the push-out bond strength of hydraulic cements in retrograde obturation.

This study examined the effect of ethylenediaminetetraacetic acid (EDTA) and etidronic acid (HEDP) in retrograde cavities on the bond strength of MTA Angelus and NeoPutty. Sixty-six teeth with single roots and canals were decoronated and enlarged up to F3 using the ProTaper Universal file system. After removing the apical 3 mm within the scope of endodontic surgery procedures, retrograde cavities were prepared with ultrasonic tips. The teeth were divided into three main groups according to the irrigation solution used: saline, 17% EDTA, and 9% HEDP. Following the irrigation of retrograde cavities, each main group was further divided into two subgroups in terms of using MTA Angelus and NeoPutty as retrograde filling materials. Bond strength values of hydraulic cements were measured by the push-out test. Fracture modes were examined under a stereo microscope. Two dentin sections from each group were examined under scanning electron microscopy (SEM) to observe dentinal tubules. Two-way ANOVA and post hoc Tukey tests were used to analyze the data. Irrigation solutions similarly affected the bond strength values of hydraulic cements (P=0.115). MTA Angelus showed significantly higher values than NeoPutty in all the solution groups (P=0.34). Adhesive and cohesive fracture modes were mostly observed in the MTA Angelus and NeoPutty groups, respectively. EDTA, HEDP, and saline had a similar effect on the bond strength of hydraulic cements. The higher bond values of MTA Angelus compared to NeoPutty could support its safe use in endodontic surgery procedures.

Effect of Surface Treatments Applied to 3D Printed Permanent Resins on Shear Bond Strength.

3D-printed permanent resins have recently been introduced to produce permanent restorations. The aim of this study is to evaluate the effect of surface treatment methods on the shear-bond strength (SBS) between 3D-printed permanent resins and adhesive cement. In this study, samples were produced using digital light projection (DLP) and stereolithography (SLA) 3D printers with two permanent resins (Crowntec, Saremco and Permanent Crown, Formlabs) in accordance with manufacturer guidelines. The samples were separated into three groups: sandblasting, hydrofluoric acid and no surface treatment. The surface profile (Ra, Sa) of the samples was examined with a confocal microscope (Smartproof 5, Zeiss). Then, a self-adhesive resin cement was applied to the samples in a transparent mold (2.38 mm diameter) in accordance with ISO 29022:2013. A universal testing machine was used to perform SBS test. A stereomicroscope was used to analyze the different types of fractures. A two-way analysis of variance (ANOVA) test was used to assess the data (p<0.05). The samples with sandblasting applied to the surface showed higher surface roughness values than the samples with hydrofluoric acid (p<0.001). 3D printer technology and surface treatment methods affected SBS values (p<0.001). Sandblasting groups higher SBS values were than in the hydrofluoric acid group (p<0.001). Sandblasting revealed cohesion fractures, which indicated a stronger bond, while hydrofluoric acid displayed adhesive and mix fractures. When sandblasting was applied to the surface of the samples prepared using permanent resins, higher adhesion was achieved with adhesive cement. Key words:3D printing, Shear bond strength, Sandblasting, Stereolithography.

Regulation interfacial energy by reducing the Young’s modulus of perovskite film in carbon-based HTM free MAPbI3 perovskite solar cell

In ambient air, a long-chain dodecafluorosuberic acid (DFSA) with lower Young’s modulus was introduced to improve the mechanical compatibility of perovskite/carbon interface. Firstly, the carbonyl groups CO and F– in DFSA can passivate the intrinsic defects of perovskite, the DFSA effectively reduces the Young’s modulus of the perovskite and mitigates residual stress generated during perovskite annealing procedure. Most importantly, DFSA significantly enhances the Young’s modulus compatible degree between DFSA-CH3NH3PbI3 (DFSA-MAPbI3, 35.8 GPa) and carbon (6.3 GPa), alleviating the interfacial stress concentration. Based on quantitatively analysis, interfical crack driving energy (Gd) is reduced from 0.63 to 0.43 J m−2, while the adhesive fracture energy (Ga) is increased from 0.47 to 0.54 J m−2, which reduces the probability of crack propagation and ductile delamination, and is conducive to the extraction and transmission of photogenerated carrior. This was also verified in finite element simulations. Finally, the photoelectric conversion efficiency (PCE) of the organic-inorganic hybrid perovskite (MAPbI3) PSC device is improved from 10.27 % to optimal 14.12 %. After service at room temperature with relative humidity (RH) of 50–55 % and high temperature of 85 °C for 720 h, the original efficiency is maintained at 72 % and 89 %, respectively.

Research on the electronic properties of TiB2/γ-Fe(1 1 1) and TiB2/Ni(1 1 1) interfaces

In order to explore the interfacial bonding mechanisms of TiB2/γ-Fe and TiB2/Ni in the composites, the adhesion work, electronic properties and fracture toughness of the TiB2(001)/ γ-Fe(111) and TiB2(001)/Ni(111) interfaces were investigated using first-principles calculations. The results reveal that the surface energy of the TiB2 surface at the B-terminated is the smallest and the constructed TiB2(001)/ γ-Fe(111) interface has the largest adhesive energy. The electronic structures of the TiB2(001)/γ-Fe(111) and TiB2(001)/Ni(111) interfaces reveal that bonding at the interfaces is provided by the B-2p orbitals with the Fe-3d and Ni-3d orbitals, respectively, and that the formation of Fe-B and Ni-B covalent/ionic bonds is the main source of bonding and interaction. The bonding and strength of Fe-B in the TiB2(001)/γ-Fe(111) interface is stronger than that in the TiB2(001)/Ni(111) interface, which is due to the higher charge density accumulation of Fe atoms at the TiB2(001)/γ-Fe(111) interface. Using Griffith’s theory, the TiB2(001)/γ-Fe(111) interface is inferred to have the strongest fracture toughness. This study suggests that the chemical bonding stronger Fe-B bonds result in a high bond strength and a more stable interfacial structure at the TiB2(001)/ γ-Fe(111) interface, leading to better resistance to cracking in practice.

Preparation and tribological properties of WS2 solid lubricating coating with dense structure using HiPIMS

In this study, a dense WS2 coating was deposited via high-power impulse magnetron sputtering (HiPIMS) after solving the glow discharge problem, and it was compared with WS2 coating deposited via radio frequency (RF) sputtering. The latter showed a columnar growth, with a loose and porous microstructure. The columnar crystal growth of the former was inhibited, resulting in a more compact coating structure and a more uniform, flatter and smoother surface. Therefore, the structure and tribological properties of WS2 coating prepared via HiPIMS were investigated under different loads and frictional frequencies. Under low loads (up to 15 N), the coefficient of friction (COF) decreased with polishing wear mechanism. Under a high load of 20 N, the COF rapidly increased, the wear rate was the highest, and the wear mechanism changed from polishing to abrasive wear. At low frequencies (5 and 10 Hz), the coating had a low and stable COF, good wear resistance and the wear mechanism was abrasive wear. At high frequencies (≥15 Hz), the COF and wear rates rapidly increased and the wear mechanism changed from abrasive to adhesive wear and plastic fracture. However, the friction and wear rates were similar across different wear mechanisms.

Physico-Mechanical Properties and Bonding Performance of Graphene-Added Orthodontic Adhesives.

This study aimed to assess the key physico-mechanical properties and bonding performance of orthodontic adhesives with graphene addition for bonding a fixed retainer. Transbond LR (3M) and Transbond LV (3M) with no graphene were set as the control groups. Graphene was added into LR and LV at concentrations of 0.01 wt%, 0.05 wt% and 0.1 wt%. The stickiness of the uncured samples (n = 5) and real-time degree of conversion (DC) of the samples (n = 3) were measured over a 24-h period using Fourier-transform infrared spectroscopy. The hardness and other mechanical parameters, including the Martens hardness (HM), indentation modulus (EIT), elastic index (ηIT) and creep (CIT), were measured (n = 5). To measure the shear bond strength (SBS), adhesive composites were applied using a mold to bond the retainer wire to the lingual surfaces of bovine incisors (n = 10). Fracture modes subsequent to the SBS test were examined under light microscopy. Statistical analysis was conducted using ANOVA and Tukey tests (α = 0.05). In the LR groups, the LR + 0.01 showed the highest SBS (12.6 ± 2.0 MPa) and HM (539.4 ± 17.9 N/mm2), while the LV + 0.05 (7.7 ± 1.1 MPa) had the highest SBS and the LV + 0.1 had the highest HM (312.4 ± 17.8 N/mm2) among the LV groups. The most frequent failure mode observed was adhesive fracture followed by mixed fracture. No statistical difference was found between the graphene-added groups and the control groups in terms of the EIT, ηIT and CIT, except that the CIT was significantly lower in the LR + 0.01 than in the control group. Graphene addition had no significant adverse effect on the stickiness and DC of both LR and LV.

Comparative evaluations of shear bond strength of mineral trioxide aggregate, Biodentine, and calcium-enriched mixture to bulk-fill flowable composite using three different adhesive systems: An in vitro study.

The objective of the study was to assess the shear bond strength of bulk-fill flowable composite resin smart dentin replacement plus when bonded to mineral trioxide aggregate (MTA)-angelus, biodentine, and calcium-enriched mixture (CEM) at two different aging periods (15 min and 72 h) using three distinct adhesive systems. In addition, the study identified the specific modes of failure (adhesive, cohesive, or mixed) using a stereomicroscope and scanning electron microscope. One hundred and twenty-six cylindrical acrylic blocks used in the study were sorted into three groups based on the bioactive substance used to fill the 3-mm diameter and 3-mm high hole in the center of each block. The groups were MTA, Biodentine, and CEM. The specimens were then divided into subgroups based on the aging interval (15 min and 72 h) of the bioactive material and the adhesive system used (two-step total-etch, two-step self-etch [SE], and one-step SE) while bonding to the restorative bulk-fill flowable composite. The shear bond strength values were measured with a universal testing machine, and the data were analyzed using two-way and one-way analysis of variance, followed by a post hoc test. The specimens were assessed under stereomicroscope and scanning electron microscope to characterize the mode of bond failure (cohesive, adhesive, or mixed). The study showed that the type of adhesive system and the time of bonding affected the shear bond strength of bulk-fill composite to the pulp capping agents (P < 0.05). For MTA, the highest bond strength was observed with two-step SE group at 15 min (18.16 ± 2.97 MPa) (P < 0.05). CEM exhibited the highest bond strength with two-step SE group at 72 h intervals (8.77 ± 1.76) (P < 0.05). The highest bond strength for biodentine group was observed with total-etch group (8.54 ± 1.35 Mpa) and two-step SE (8.19 ± 1.94 Mpa) bonded at 72 h interval (P < 0.05). The majority of the samples in the MTA group (29/42) and CEM group (20/42) showed a cohesive fracture, whereas Biodentine group (22/42) had an adhesive fracture in most of its samples. MTA demonstrated the highest bond strength with two-step SE group at 15 min, and CEM exhibited the highest bond strength with two-step SE groups at 72 h interval. For biodentine group, the type of adhesive used did not impact the bond strength values.

“Like binding a book”: Interfacial improvement of pre-melted ultrahigh molecular weight polyethylene by pulse vibration molding

Ultrahigh molecular weight polyethylene (UHMWPE) is widely used in industrial, military, and civilian applications owing to its excellent properties. However, the high entanglement degree of UHMWPE melt leads to great difficulties in diffusion and crystallization, which causes poor interfacial strength and mechanical properties of pre-melted UHMWPE, restricting its high-quality processing and high-value recycling. To this end, we propose a rapid interface stitching technology with a pulsed vibration force driving free volume homogenization and chain segment orientation. For the first time, pulse vibration molding (PVM) is applied for the hot-pressing of pre-melted UHMWPE, successfully realizing the interface stitching and product strengthening. Compared with those of the convention molding (CM) samples at 180 °C, the interfacial adhesive fracture toughness of the adhesive samples processed using PVM is increased by 105.9 % and the work of tension of the recycled samples processed using PVM is also increased by 49.09 %, respectively. The fracture strength of the PVM recycled samples at 180 °C reaches 91.77 % of that of the pure samples and the yield strength is also higher, which significantly enhances the recycling of UHMWPE. The characterization results of the interfacial molecular chain entanglement and crystallization show that PVM strengthens the molecular chain diffusion and induces crystallization by promoting the orientation of chain segments, especially at the interface. Consequently, we believe that the proposed technology can play a significant role in the UHMWPE processing methods that involve surface healing.

Influence of modelling hypotheses on strength assessment of CFRP stepped repairs

Composite stepped repairs can achieve high strength recovery without the addition of bolts or fasteners to the structure. They are therefore a major issue in the field of aerospace composite structure damage repair. However, there is no standardized method to design this type of repairs. Many analytical, semi-analytical and finite element models were proposed throughout the years to predict the strength of stepped repairs, using various hypotheses and simplifications. The aim of this paper is to investigate the influence of modelling hypotheses on stress distribution and strength prediction of composite stepped repairs. Five simplified stepped joint models using macro-element (ME) modelling and finite element method (FE) are compared to a full 3D FE model of a stepped repaired panel. The influence of step length and adhesive fracture toughness was investigated to determine the field of validity of each model. Among FE models, it was shown that modelling the equivalent joint under 2D generalized plain strain gives a very close strength prediction to the 3D stepped repair model while saving computation time. Simplified macro-element models under bar or beam hypotheses are fairly close to the results of FE modelling, but the deviation between those and FE is sensitive to step length and adhesive fracture toughness.

Tuning mechanical properties of TiAlSiN/TiAlN multilayers by interfacial structure

Multilayer structure as an effective way to tailor the structure and performance of hard coatings has attracted wide attentions. Here, we aim to elucidate the change of the interface, mechanical properties and oxidation resistance for TiAlSiN/TiAlN multilayers by varying modulation ratios from ML (tTiAlSiN/tTiAlN = 1:1) to HML (tTiAlSiN/tTiAlN = 1:2). Increasing TiAlN sublayer thickness stabilizes the cubic growth of TiAlSiN layers, where the HML exhibits coherent epitaxial growth in contrast to the cubic-wurtzite mixed structure of ML. This coherent strengthening effect is responsible for the noteworthy enhancement of the hardness values from ∼30.9 GPa of ML to ∼33.2 GPa of HML. Significantly, the presence of a coherent interface effectively withstands external pressure, thereby endowing HML with exceptional adhesive strength and fracture toughness. Nevertheless, the oxidation resistance of the coating is reliant on the chemical composition, with the multilayers displaying lower oxidation resistance compared to the TiAlSiN monolayer.

Microtensile Bond Strength of Self-Etch Adhesives on Dentin Treated with Chlorhexidine.

To evaluate the microtensile bond strength of self-etching adhesive systems in dentin treated with 2% chlorhexidine digluconate (CHX). The occlusal surfaces of 20 human molars were removed and divided into eight groups: 1A, Clearfil SE adhesive (SE) with self-etching technique (TS); 1B, SE with TS and previous application of CHX; 2A, Scotchbond Universal (SBU) adhesive with TS; 2B, SBU adhesive with TS and previous application of CHX; 1C, SE with total-etching technique (TT); 1D, SE with TT and previous application of CHX; 2C, SBU with TT; 2D SBU with TT and previous application of CHX. Composite resin (5mm) was applied on the hybridized surface. Samples were subjected to microtensile test and evaluated on Scanning Electron Microscope (SEM) and with energy-dispersive X-ray (EDX). Low values of bond strength were observed in groups 1A (39,77±11,56) and 2A (40,84±12,49) comparing with 1B (22,86±5,18) and 2B (27,02±5,58). TS group presented adhesive type remover fracture while TT groups presented cohesive at the top of hybrid layer. EDX revealed the presence of CHX crystals for TS, which was not found in the TT. The previous application of chlorhexidine on dentin decreased the bond strength of adhesive systems on self-etching technique.

An enhanced surface treatment for effective bonding of 7075-T6 aluminium alloys

ABSTRACT This study research focuses on optimising adhesion through surface treatments on 7075-T6 aluminium alloy substrates using a chromium-free protocol. The treatment involves acetone degreasing, NaOH etching, and sulphuric acid-based solution etching. Wettability analysis and scanning electron microscopy were used to characterise the treated surfaces, highlighting the effectiveness of the proposed protocol. The proposed etching protocol was then applied to aluminium alloy substrates, and fracture surfaces corresponding to each treatment were compared. Mechanical testing, specifically double cantilever beam (DCB) experiments, assesses the fracture energy of bonded assemblies in mode I. The results demonstrate that the sulphuric acid-based treatment significantly improves the surface characteristics, leading to enhanced adhesion and optimal fracture energy in bonded aluminium assemblies.

Dynamic fracture response of adhesive joints subjected to mode-I impact wedge loading

ABSTRACT This paper aims to examine the behavior of cracked adhesive joints experimentally and numerically when they are subjected to quasi-static and dynamic loads using the tensile and falling-wedge impact tests, respectively. Double cantilever beam (DCB) specimens were manufactured and tested under impact loading with varying impact energies to analyze the adhesive joint mode-I dynamic fracture response. To determine quasi-static and dynamic mode-I fracture energies, the compliance-based beam method (CBBM) was utilized accounting for the axial force exerted by the wedge. It was found that by changing the loading condition from quasi-static to impact, the maximum force and fracture energy of adhesively bonded joints were considerably increased by 275% and 452%, respectively. However, within the impact test conditions, increases of 10% and 22% were obtained in maximum force and fracture energy when the impact energy was tripled. The adhesive joints tested under static loading experienced a mixed interfacial/cohesive failure pattern, whereas by shifting the loading condition to impact, the failure pattern turned fully cohesive. The quasi-static and dynamic fracture responses of adhesive joints were modeled using the cohesive zone model employing a triangular traction-separation law. The numerical and experimental results exhibited reasonable correlation.

The effect of abrading treatment method on the bonding surface characteristics and fracture behavior of glass fiber-epoxy composite adhesive joints

The effect of the mechanical abrading method on the bonding surface characteristics and fracture response of glass fiber-reinforced polymer (GFRP) composite adhesively bonded joints was investigated. Double cantilever beam specimens were manufactured by bonding GFRP substrates with an epoxy adhesive to evaluate the mode-I adhesive joint fracture response. The bonding surfaces were treated with degreasing and abrading methods utilizing sandpapers with various grit sizes ranging from P60 to P800. The results showed that the sandpaper grit size can considerably change the bonding surface properties comprising the surface energy, roughness, morphology, and water drop contact angle and consequently, it can affect the joint fracture behavior. Reducing the sandpaper grit size continuously increased the surface roughness but there were optimum values for the surface energy and water drop contact angle. The fracture resistance of adhesive joints followed the trend of bonding surface energy as the higher the bonding surface energy, the higher the joint fracture resistance. The fracture energy and load-bearing capacity of adhesive joints were improved by 62 and 34%, respectively, when the joint bonding surfaces were abraded with P240. However, further reducing the sandpaper grit size to P60 caused a decrease in the fracture energy and load-bearing capacity of adhesive joints by 18 and 44%, respectively, compared to the joint with degreased and non-abraded bonding surfaces. Moreover, the abrading method considerably changed the microscopic and macroscopic failure modes of adhesive joints.

Preheated acid associated with silane and electric current in the adhesion of the resin cement to ceramic.

This study verified the effect of the combination of preheated hydrofluoric acid/silane/electric current in the adhesion of the resin cement to ceramic. IPS E.max Press ceramic discs embedded in PVC rigid tubes were divided into four groups associating preheated hydrofluoric acid and silane applied with electrical current (n=10): Ha+S (Heated acid + silane); Ha+S+Ec (Heated acid + silane + electrical current); A+S (Acid + silane) and A+S+Ec (Acid + silano + electrical current). Resin cement/ceramic samples were stored in water at 37°C for 24h. After storage, they were submitted to the microshear test, fracture analysis, and contact angle at 24h or after thermocycling (10,000 cycles/5-55ºC). Bond strength data were evaluated by two-way ANOVA. For comparison between evaluation times (24h or thermocycling) was applied unpaired t-test. A significance post-hoc test of p=0.05 was assumed for analyses and graphs (GraphPad Prism 9.0 software). At 24h, the microshear strength showed similar values between Ha+S, Ha+S+Ec, and A+S+Ec groups, while A+S showed the lowest value with a statistical difference. After thermocycling, Ha+S and Ha+S+Ec were similar, as well as A+S and A+S+Ec. There was a significant difference in all groups comparing 24h (highest value) with after thermocycling (lowest value). Adhesive fracture was predominant in all groups and evaluation times. Ha+S and A+S groups showed higher contact angle values compared to the Ha+S+Ec and A+S+Ec with lower values. In conclusion, the association of preheated hydrofluoric acid/silane applied or not with electric current promoted different microshear strength values, fracture types, and contact angles in the resin cement/ceramic bond.

Development of Ti/Ti-DLC multilayers on magnesium alloys. Part 1: Microstructure and mechanical properties

To improve both the corrosion resistance and wear resistance of magnesium alloys, titanium-diamond-like carbon (Ti-DLC) monolayer and Ti/Ti-DLC multilayer films with two periods were applied to AZ31 magnesium alloys through filter cathodic vacuum arc deposition technology. The Ti-DLC monolayer film exhibited an amorphous structure doped with TiC nanocrystals. After introducing the Ti sublayer, the Ti/Ti-DLC multilayer films exhibited a layered structure, resulting in improved adhesion strength and fracture toughness and lower hardness. Compared with the (Ti/Ti-DLC)4 multilayer film with a smaller period, the (Ti/Ti-DLC)2 multilayer film with a lager period exhibited better adhesion strength, higher fracture toughness, hardness, ID/IG ratio, and lower residual stress owing to its thicker Ti sublayers.

Using cohesive zone models with digital image correlation to obtain a mixed mode I/II fracture envelope of a tough epoxy

This work describes a method in which the digital image correlation (DIC) method and finite element analysis (FEA) were used to create a quasi-static mixed-mode fracture envelope for bonded joints consisting of 2024-T3 Al adherends and a tough structural epoxy adhesive. Symmetric and asymmetric versions of double cantilever beam, single-leg bend, and end-notched flexure tests are used to populate the mixed-mode fracture envelope with results at several mode mixities. Experiments are conducted in a universal testing machine while recording images for subsequent DIC analysis. Finite element analysis is used to implement cohesive zone models (CZMs) of the adhesive fracture and to account for plastic deformation of adherends. Mode I and mode II traction separation laws (TSLs) are determined from a property identification method with a Benzeggagh–Kenane mixed-mode coupling law used to model mixed-mode behavior. FEA results are shown to provide a good agreement to both the crosshead displacement and DIC data. The methods in this paper serve as a potential framework for future calibration of mixed-mode fracture envelopes for joints bonded with very tough adhesives that complicate assessment with traditional data analysis methods.

The Effect of Bevel on Fracture Resistance of GIC Restorations in Primary Molars: An “In Vitro Study”

Introduction: Glass ionomer cements (GICs) are commonly used for restorations in primary molars due to their adhesive, hydrophilic, and bioactive properties. However, their low mechanical resistance may limit their use in proximal cavities. Recent advancements in GICs, such as the high viscosity GIC EQUIA Forte®, have improved their mechanical properties. The effect of a Cavo superficial bevel on the mechanical strength of GIC restorations has been previously studied. Objectives: To investigate the effect of a Cavo superficial bevel on fracture resistance and the type of fracture (adhesive, cohesive, or catastrophic) in EQUIA Forte® GIC restorations in primary molars. Methods: A total of 66 standardized proximal cavities were created on 51 temporary molars. The cavities were randomly divided into two groups: group I without a Cavo superficial bevel (n=33) and group II with a 45° Cavo superficial bevel (n=33). The cavities were restored with EQUIA Forte®. The samples were subjected to thermocycling and artificial aging, then, an axial speed loading of 1 mm/min was applied until fracture. Fracture toughness was recorded, and the type of fracture was observed under an optical microscope. A Mann-Whitney U test was used to compare the average fracture resistance between the groups. All tests were two-tailed and the level of significance was set at 5%. Results: The average fracture resistance for group I was (237.57 ± 139.97 N) and for group II was (294.89 ± 171.07 N). There was no statistically significant difference in fracture resistance between the two groups (p&gt;0.05). Mixed fractures were observed in all samples, with adhesive fractures only present in group I and cohesive fractures only present in group II. Conclusions: The Cavo superficial bevel does not significantly affect the fracture resistance of GIC resto rations in primary molars. However, the bevel design may prevent adhesive and catastrophic fractures.