Addition Of Plasticizer Research Articles

Role of benzophenone-3 additive in the effect of polyethylene microplastics on Daphnia magna population dynamics

The adverse effects of microplastics (MPs) on Daphnia magna have been extensively studied; however, their population-level effects are relatively unknown. This study investigated the effect of polyethylene MP fragments (33.90 ± 17.44 μm) and benzophenone-3 (BP-3), which is a widely used plastic additive (2.91 ± 0.02% w/w), on D. magna population dynamics in a 34-day microcosm experiment. In the growth phase, neither MP nor MP/BP-3 fragments changed the population size of D. magna compared with the control. However, MP/BP-3 fragments significantly reduced (p < 0.05) the population biomass compared to that of the control, whereas MP fragments did not induce a significant reduction. The MP/BP-3 group had a significantly higher (p < 0.05) neonate proportion than that in the control and MP groups. MP/BP-3 fragments upregulated usp and downregulated ecrb, ftz-f1, and hr3, altering gene expression in the ecdysone signaling pathway linked to D. magna growth and development. These findings suggested that BP-3 in MP/BP-3 fragments may disrupt neonatal growth, thereby decreasing population biomass. In the decline phase, MP fragments significantly decreased (p < 0.05) the population size and biomass of D. magna compared with the control and MP/BP-3 fragments. This study highlights the importance of plastic additives in the population-level ecotoxicity of MPs.

Harmonizing the cyano-group and Na to enhance selective photocatalytic O2 activation on carbon nitride for refractory pollutant degradation

Manipulating exciton dissociation and charge-carrier transfer processes to selectively generate free radicals of more robust photocatalytic oxidation capacity for mineralizing refractory pollutants remains challenging. Herein, we propose a strategy by simultaneously introducing the cyano-group and Na into graphitic carbon nitride (CN) to obtain CN-Cy-Na, which makes the charge-carrier transfer pathways the dominant process and consequently achieves the selective generation of free radicals. Briefly, the cyano-group intensifies the local charge density of CN, offering a potential well to attract the hole of exciton, which accelerates the exciton dissociation. Meanwhile, the separated electron transfers efficiently under the robust built-in electric field induced by the cyano-group and Na, and eventually accumulates in the heptazine ring of CN for the following O2 reduction due to the reinforced electron sink effect caused by Na. As a result, CN-Cy-Na exhibits 4.42 mmol L-1 h-1 productivity with 97.6% selectivity for free radicals and achieves 82.1% total organic carbon removal efficiency in the tetracycline photodegradation within 6 h. Additionally, CN-Cy-Na also shows outstanding photodegradation efficiency of refractory pollutants, including antibiotics, pesticide plastic additives, and dyes. This work presents an innovative approach to manipulating the exciton effect and enhancing charge-carrier mobility within two-dimensional photocatalysts, opening an avenue for precise control of free radical generation.

Plastic additives in commercial fish of Aegean and Ionian Seas and potential hazard to human health

Plastic additives include a wide range of pollutants, added throughout the production process of plastics aiming to improve their properties. Given that they are not chemically bound to the plastic items, they can easily migrate in the marine environment allowing their uptake by marine organisms and accumulation in their tissues. Representatives of Phthalic acid esters (PAEs) and bisphenols have been characterized for their ability to impact not only marine organisms but also humans via fish and seafood consumption. In this study, a liquid-liquid method was applied to determine the concentrations of selected PAEs and Bisphenol A (BPA) in the tissues of E.encrasicolus, S.pilchardus, B.boops, and M.barbatus from two important divisions of fisheries (North Aegean and the Western Ionian Seas, thereof NAS and IOS respectively) of the Mediterranean Sea. The level of contamination varied among the different species and geographical locations. DEHP (bis(2-ethylhexyl) phthalate) had the highest mean concentrations of the examined PAEs for all four species examined. Statistically significant differences in DEHP mean concentrations were observed between the tissues of B.boops (collected from NAS) and S.pilchardus (from IOS) (p &amp;lt; 0.05, Wilcoxon rank test). DIDP (di-isodecyl phthalate) was the following most common PAEs, although no statistically significant differences were presented between sites, species, and tissues. DINP (di-isononyl phthalate) was recorded only in the GIT of E.encrasicolus (from NAS), while the rest of the examined PAEs were presented in a smaller subset of the samples. Noticeably, the parent diester DBP and the metabolic monoester MNBP were concurrently detected in a part of the analyzed samples. The level of risk via fish consumption, based on the Estimated Daily Intake and the Target Hazard Quotient (THQ), showed that the PAEs and BPA had a low likelihood of a negative effect occurring for every scenario that was examined, although THQ for BPA indicated there was a higher likelihood than PAEs of an adverse effect to be presented. The results of this study highlighted the need for future efforts focusing on the factors affecting plastic additives occurrences in the marine environment, especially for marine organisms intended for consumption.

Improved microalgae carbon fixation and microplastic sedimentation in the lake through in silico method

The impact of microplastics in lake water environments on microalgae carbon fixation and microplastic sedimentation has attracted global attention. The molecular dynamic simulation method was used to design microplastic additive proportioning schemes for improving microalgae carbon fixation and microplastic sedimentation. Results showed that the harm of microplastics can be effectively alleviated by adjusting the proportioning scheme of plastic additives. Besides, the decabromodiphenyl oxide (DBDPO) was identified as the main additive that affect the microalgae carbon fixation and microplastic sedimentation. Thus, a molecular modification based on CiteSpace visual analysis was firstly used and 12 DBDPO derivatives were designed. After the screening, DBDPO-2 and DBDPO-5 became the environmentally friendly DBDPO alternatives, with the highest microalgae carbon fixation and microplastic sedimentation ability enhancement of over 25 %. Compared to DBDPO, DBDPO derivatives were found easier to stimulate the adsorption and binding ability of surrounding hotspot amino acids to CO2 and ribulose-5-phosphate, increasing the solvent-accessible surface area of microplastics, thus improving the microalgae carbon fixation and microplastic sedimentation ability. This study provides theoretical support for simultaneously promoting the microalgae carbon fixation and microplastic sedimentation in the lake water environment and provides scientific basis for the protection and sustainable development of lake water ecosystem.

A narrative review of microplastics in the indoor and outdoor environment, human effects, and ecological risks

Due to their widespread identification in all environmental compartments, Microplastics (MPs) are emerging pollutants that have garnered growing scientific and public attention over the last decades. Early research on MPs and their effects was limited to studies of terrestrial and aquatic ecosystems, but more recent studies have included MPs in the air. There is now considerable concern about the effects of MPs on pristine environments and urban air quality.&#x0D; A literature search was conducted in Science Direct and Google Scholar using the following keywords: microplastics, indoor environment, outdoor environment, human effects, and ecological risks.&#x0D; Finally, eligible studies were selected for the review. Textiles, such as clothes, carpets, and curtains, are the main indoor sources of MPs. As well as the primary sources of MPs outdoors, there are landfills, urban and home dust, and synthetic particles. According to current theories, human exposure to MPs occurs through dermal contact, ingestion, and inhalation. Recent research has demonstrated that inhalation is the principal mechanism of human exposure to MPs. Early toxicological research suggests that MPs may lead to inflammation and oxidative stress. However, there is growing concern about the possible leaching of hazardous chemicals used as plastic additives. Nevertheless, MP exposure and risk assessment in humans is still in its infancy, and more research on the presence of MPs in various indoor and outdoor environments is required to provide the knowledge base needed for regulations to protect human health and the environment from MPs.

Temporal evolution of plastic additive contents over the last decades in two major European rivers (Rhone and Rhine) from sediment cores analyses

Although global plastic distribution is at the heart of 21st century environmental concerns, little information is available concerning how organic plastic additives contaminate freshwater sediments, which are often subject to strong anthropogenic pressure. Here, sediment core samples were collected in the Rhone and the Rhine watersheds (France), dated using 137Cs and 210Pbxs methods and analysed for nine phthalates (PAEs) and seven organophosphate esters (OPEs). The distribution of these organic contaminants was used to establish a chronological archive of plastic additive pollution from 1860 (Rhine) and 1930 (Rhone) until today. Sediment grain size and parameters related to organic matter (OM) were also measured as potential factors that may affect the temporal distribution of OPEs and PAEs in sediments. Our results show that OPE and PAE levels increased continuously in Rhone and Rhine sediments since the first records. In both rivers, ∑PAEs levels (from 9.1 ± 1.7 to 487.3 ± 27.0 ng g−1 dry weight (dw) ± standard deviation and from 4.6 ± 1.3 to 65.2 ± 11.2 ng g−1 dw, for the Rhine and the Rhone rivers, respectively) were higher than ∑OPEs levels (from 0.1 ± 0.1 to 79.1 ± 13.7 ng g−1 dw and from 0.6 ± 0.1 to 17.8 ± 2.3 ng g−1 dw, for Rhine and Rhone rivers, respectively). In both rivers, di(2-ethylhexyl) phthalate (DEHP) was the most abundant PAE, followed by diisobutyl phthalate (DiBP), while tris (2-chloroisopropyl) phosphate (TCPP) was the most abundant OPE. No relationship was found between granulometry and additives concentrations, while organic matter helps explain the vertical distribution of PAEs and OPEs in the sediment cores. This study thus establishes a temporal trajectory of PAEs and OPEs contents over the last decades, leading to a better understanding of historical pollution in these two Western European rivers.

Effects of the plastic additive 2,4-di-tert-butylphenol on intestinal microbiota of zebrafish

Plastic additives such as the antioxidant 2,4-di-tert-butylphenol (2,4-DTBP) have been widely detected in aquatic environments, over a wide range of concentrations reaching 300 μg/L in surface water, potentially threatening the health of aquatic organisms and ecosystems. However, knowledge of the specific effects of 2,4-DTBP on aquatic vertebrates is still limited. In this study, adult zebrafish were exposed to different concentrations of 2,4-DTBP (0, 0.01, 0.1 and 1.0 mg/L) for 21 days in the laboratory. The amplicon sequencing results indicated that the diversity and composition of the zebrafish gut microbiota were significantly changed by 2,4-DTBP, with a shift in the dominant flora to more pathogenic genera. Exposure to 2,4-DTBP at 0.1 and 1.0 mg/L significantly increased the body weight and length of zebrafish, suggesting a biological stress response. Structural assembly defects were also observed in the intestinal tissues of zebrafish exposed to 2,4-DTBP, including autolysis of intestinal villi, adhesions and epithelial detachment of intestinal villi, as well as inflammation. The transcriptional expression of some genes showed that 2,4-DTBP adversely affected protein digestion and absorption, glucose metabolism and lipid metabolism. These results are consistent with the PICRUSt2 functional prediction analysis of intestinal microbiota of zebrafish exposed to 2,4-DTBP. This study improves our understanding of the effects of 2,4-DTBP on the health of aquatic vertebrates and ecosystems.

Assessment of the impact of microplastic ingestion in striped red mullets from an Eastern Mediterranean coastal area (Zakynthos Island, Ionian Sea)

Monitoring microplastics (MPs) in the marine environment is an ongoing process, and our understanding of their impact on marine organisms is limited. The present study evaluates the effects of ingested MPs on the marine MP pollution bioindicator fish species Mullus surmuletus. The study follows a three-fold approach to assess the impact of MPs on marine organisms by investigating: 1) the ingestion of MPs, 2) the bioaccumulation of phthalate compounds as plastic additives, and 3) the evaluation of toxicological biochemical and cellular biomarkers. Striped red mullets were sampled in the marine protected area (MPA) of the National Marine Park of Zakynthos and coastal sites with high touristic pressure in Zakynthos Island in the Ionian Sea, Greece. Fewer ingested MPs and lower phthalate concentrations were found in fish inside the MPA compared to those sampled outside the marine park. However, no relationship was found between either phthalate concentrations or biomarker levels with the ingested MPs in the red striped mullets. Biomarker levels were influenced by season and site, but no effect could be attributed to the ingested MPs. The lack of association of biomarker responses and plasticizer bioaccumulation to MP ingestion can be explained by the low number of ingested MPs in the fish from Zakynthos coastal area as MP abundance ranged from 0.15 to 0.55 items per individual fish.

B-esterases activities in several tissues of the marine fish: sea bass and hake, as potential biomarkers of bisphenol A derivatives

In the marine environment, a new threat linked to plastic pollution relates to plastic additives. This threat encompasses multiple chemical compound groups with a high bioaccumulation potential for these chemical mixtures. Hence, informative biomarkers are needed to indicate the effects of environmentally realistic mixtures of these additives. This study proposes an in vitro approach using tissue homogenates of two marine fish, the European sea bass and hake, which are both of interest in aquaculture and fisheries. The selected biomarkers are B-esterase activities comprising acetylcholinesterase (AChE) and carboxylesterases (CEs). The physiological role of AChE in brain and muscle is mainly neural transmission, while CEs participate in liver detoxification processes. However, B-esterases are also widely distributed in other tissues/organs, where their role is yet to be determined, but their inhibition may have undesired biological consequences. Here, we compared the interaction of the plastic additives, bisphenol A and some of its derivatives, like tetrabromobisphenol A (TBBPA), with B-esterase activities. We particularly focused not only on the robust and broadly distributed CE enzymes in brain, gonad, liver, kidney, and plasma tissues of two marine fish, but also on the use of two commercial substrates, p-nitrophenyl butyrate and α-naphthyl butyrate, tentatively representing two CE isoforms. The results evidenced specific species and tissue responses that could be due to a diverse isoform composition. They identified sea bass as better protected against neurotoxic exposures, at least in terms of B-esterase composition. The flame retardant TBBPA was the most reactive to B-esterases inhibition, although Bisphenol A bis (2,3-dihydroxy propyl) ether and Bisphenol F bis (3-chloro-2-hydroxypropyl) ether warrant further toxicology assessments.

Utilization of taro beneng (xantoshoma undipes k.koch) starch in the manufacture of bioplastics with sorbitol plasticizer and its characterization

Preparation of bioplastics and chitosan with sorbitol plasticizer by varying starch and chitosan in the ratio of 30%: 70%, 40% : 60%, 50% : 50%, 60% : 40%, 70% : 30% and added sorbitol plasticizer with variations of 60% and 80%. Characterization was carried out on the composition of starch and chitosan with the addition of sorbitol plasticizer starting with physical and mechanical testing and obtained 2 bioplastics showing the highest elongation and tensile strength data obtained in sample BSB4 in the ratio of starch and chitosan 60%: 40% by adding 60% sorbitol plasticizer showed an elongation value of 21.68898% and a tensile strength of 1.7352 MPa and sample BSC1 with a ratio of starch and chitosan 30%: 70% with the addition of 80% sorbitol plasticizer resulted in an elongation value of 23.6926% and tensile strength of 2.3997 MPa. The biodegradability test on bioplastics showed a mass reduction for 4 weeks or 28 days with the highest percentage of each variation of starch and chitosan by adding sorbitol plasticizer reaching 19.38%. SEM results show that there is still mixing between starch and a less homogeneous solution as evidenced by several points on bioplastics that are still white, and the same groups are obtained between the constituents of bioplastics, namely O-H, C-H, and N-H.

A study of the mechanical, thermal and rheological properties of sisal fiber-reinforced polylactic acid bio-composites with tributyl 2-acetylcitrate as a plasticizer

In this study, bio-composites were developed using polylactic acid (PLA) as the matrix and sisal fibers (SFs) derived from agave sisalana leaves as the reinforcement. The bio-composites were prepared through injection molding with the addition of tributyl 2-acetylcitrate (ATBC) plasticizer. The mechanical, thermal, and rheological properties of these bio-composites were investigated to understand the effects of fiber and plasticizer contents. The results showed that the addition of SFs improved the tensile and flexural moduli of the bio-composites but led to a decrease in tensile strength compared to neat PLA. The flexural strength initially decreased with low fiber content but recovered to the level of neat PLA as the fiber content increased. The impact strength increased with the incorporation of SFs and ATBC. However, the presence of ATBC had a negative impact on the tensile and flexural properties of the bio-composites. The thermal conductivity of the materials was influenced by the fiber content and processing temperature, increasing with SFs inclusion but decreasing with temperature. Differential scanning calorimetry analysis revealed increased crystallinity of PLA with the presence of SFs and ATBC. The specific heat capacity increased with ATBC but decreased with increasing SFs. Dynamic mechanical property testing showed variations in storage and loss moduli of the bio-composites at different temperatures. The storage modulus increased with higher fiber content and abruptly dropped around glass transition temperature. Rheological characterization demonstrated effective interactions between the fibers and matrix with good fiber dispersion, resulting in uniform shear viscosity versus shear rate for different capillary dimensions. The shear viscosity of the SFs/PLA mixture increased with increasing fiber content but decreased with the addition of plasticizer. Furthermore, the compounding and molding processes had a notable impact on the microstructure of the fibers, specifically resulting in fiber breakage and fiber separation during processing.

Fabrication of highly efficient biodegradable oligomeric lactate flame-retardant plasticizers for ultra-flexible flame-retardant poly (lactic acid) composites

Biobased multifunctional plastic additives not only overcome the toxicity and non-degradability of phthalates but also provide multiple functions to polymers. In this study, novel biodegradable oligomeric lactate flame-retardant plasticizers (PBCL) integrated from l-lactic acid and crotonic acid with excellent fire-retardant and plasticizing functions were synthesized to overcome the inflammability and fragileness of poly(lactic acid) (PLA). The results revealed that PBCL-plasticized PLA composites achieved a good balance between flexibility and fire retardancy. Even with a ratio of 0.2:1 of 9,10-dihydro-oxa-10-phosphaphenanthrene-10-oxide (DOPO) to 2-(2-n-butoxyethoxy) ethanol of crotonic acid lactate ester (BCL), the plasticized PLA blends showed the highest elongation at break (433.72 %), accompanied by a high limiting oxygen index (27.1 %). Remarkably, the vertical burning tests (UL-94) indicated that all blends passed UL-94 V-0 grade, signifying their superior fire resistance. Interestingly, the addition of PBCL had minimal impact on the transparency of PLA, with the transmittances of all composites still remained at above 87 % at 800 nm. Furthermore, the PBCL-plasticized PLA composites exhibited better migration resistance and volatility resistance than commercial plasticizer acetyl tributyl citrate (ATBC). Additionally, the biodegradability of PBCL was studied through the degradation experiments using active soil and tenebrio molitors, with characterization of the degradation products. The results of the biodegradation experiments showed that PBCL decomposed into non-toxic and harmless small molecules. This study presents an eco-benign method for developing biodegradable additives with flame-retardant and plasticizing functions, holding excellent prospects for industrial applications.

Effect of phthalate-free plasticizer addition on thermal, mechanical, and aging properties of nitrile rubber (NBR)

Nitrile rubber (NBR) is widely used in the automotive, aerospace, and chemical sectors due to its resistance to fuels, oil, thermal aging, and fatigue. A typical NBR compound is prepared with several components that are added to obtain a product to meet specific industry requirements. Plasticizer is one of the main components used in NBR compounds. Typically, phthalates like DBP (dibutyl phthalate) or DOP (dioctyl phthalate) are used for NBR plasticization. However, these phthalates-based plasticizers are associated with toxicity and often prohibited by international regulatory standards. In this way, in the pursuit of a non-toxic NBR compound, the use of phthalate-free plasticizer, namely dioctyl terephthalate (DOTP), has been proposed. In this work, NBR compounds with DOTP, DBP, or DOP were processed in an open mill and vulcanized in hydraulic press. The unvulcanized samples were tested in a moving die rheometer (MDR). Subsequently, thermal, mechanical, and aging analyses were conducted for the vulcanized samples. The lowest torque observed in the rheometric curve, the displacement value of glass transition temperature (Tg), the smaller Shore A hardness, and the high elongation at break indicate that the addition of DOTP results in higher plasticization. The better-aging properties indicate lower migration of the DOTP plasticizer. Thus, the use of DOTP as a plasticizer holds promise as a viable alternative to replace the phthalates-based plasticizer in NBR compounds.

Influence of Plastic Waste Management on the Environment: A review

Plastics have become a modern-day nuisance to the environment and man due to improper management at their end-of-life. The structure and additives in fossil-based plastics make them non-biodegradable and, therefore, can persist in the environment for hundreds of years. Since a small percentage of plastic waste is recycled annually (9%) most of this plastic waste is being managed by open-air incineration or disposal in landfills where these additives can easily contaminate the air, soil, and water apart from the fact that a lot of these plastic waste find their way into our water bodies resulting to a lot of harm to the Eco-system. Recycling of plastic is an effective means of tackling the menace of plastic pollution, with chemical recycling as the most effective recycling process as it completely removes the waste plastic from the environment. Manufacturing and use of bioplastics like Polylactic acid, a good substitute for fossil-based polymer polyethylene terephthalate (PET), is a welcome development with the People’s Republic of China championing in the production. Legislative tools have been enacted in countries across the globe banning the use and manufacturing of single-use plastic bags. The implementation of this legislative move has been effective in some countries like the People’s Republic of China, Morocco, and Rwanda. Nigeria enacted the Plastic prohibition bill banning the manufacturing, use, and importation of all plastic bags in May 2019. This ban does not affect the behavioral and plastic management system in Nigeria as plastic bags are still used in cities across the country, littered in waterways and landfills. Therefore, there is a need to review the bill to include waste generation and management. Emphasis should also be placed on the production, and use of cost-effective bioplastic polymers and products

Cross-linking lignin and cellulose with polymers using siloxane compounds

Siloxanes are a group of substances characterized by Si-O-Si functional group. Siloxanes can react with alcohols to form Si-O-C bond. Siloxanes have been widely used as crossing linking agents and graft copolymers as well as additives for plastics. Lignin contains both phenolic and aliphatic hydroxy groups which have the potential to instigate bonding with siloxane compounds. However, there has not been any attempt to apply siloxanes as crosslinking agents for biobased composite formation. This manuscript presents the first study of applying siloxanes compounds to lignin and Cellulose nanofibers (CNF) with respective PLA, PETG, and HDPE to prepare biocomposites. Both Tetramethyl Tetraphenyl Trisiloxane (TTT) and Tetraethoxysilane (TEOS) were used as cross-linking agents. We have successfully incorporated 20 wt% lignin and 10 wt% CNF into the biocomposite filaments. The tensile properties of ensuing biocomposite were investigated. The objective of this work is to demonstrate the potential of lignin and CNF as a sustainable co-polymer to improve the properties of PLA/PETG/HDPE-based materials for 3D printing. This paper will also discuss the challenges and opportunities associated with the use of lignin in 3D printing, including the effect of lignin and CNF content on the mechanical and thermal properties, the compatibility of lignin and CNF with PLA/PETG/HDPE, and the potential for further optimization of the cross-linking chemistry using TTT and TEOS.

The effects of plastic additives on swimming activity and startle response in marine amphipod Echinogammarus marinus

Plastic additives are widely used in plastic production and are found in the environment owing to their widespread applications. Among these additives, N-butyl benzenesulfonamide (NBBS) and triphenyl phosphate (TPHP) are under international watchlist for evaluation, with limited studies on amphipods. Di-ethylhexyl phthalate (DEHP) and dibutyl phthalate (DBP) are banned in some countries and categorised as substances of very high concern. This study aimed to investigate the effects of NBBS, TPHP, DEHP and DBP on the swimming activity of a coastal intertidal marine amphipod, Echinogammarus marinus. Furthermore, this study is the first to quantify startle response in E. marinus in response to light stimuli. Amphipods were exposed to 0, 0.5, 5, 50 and 500 μg/l concentrations of all test compounds. Swimming activity and startle responses were assessed by video tracking and analysis using an 8-min alternating dark and light protocol after exposure on days 7 and 14. We observed an overall compound and light effect on the swimming activity of E. marinus. A significant decrease in swimming distance was found in 500 μg/l NBBS and TPHP. We observed that the startle response in E. marinus had a latency period of >2 s and animals were assessed at 1 s and the sum of the first 5 s. There was a clear startle response in E. marinus during dark to light transition, evident with increased swimming distance. NBBS exposure significantly increased startle response at environmental concentrations, while significant effects were only seen in 500 μg/l TPHP at 5 s. We found no significant effects of DEHP and DBP on swimming behaviour at the concentrations assessed. The findings of this study affirm the necessity for a continuous review of plastic additives to combat adverse behavioural effects that may be transferable to the population levels.

Disposable Plastic Waste and Associated Antioxidants and Plasticizers Generated by Online Food Delivery Services in China: National Mass Inventories and Environmental Release.

China's online food delivery (OFD) services consume enormous amounts of disposable plastics. Here, we investigated and modeled the national mass inventories and environmental release of plastics and chemical additives in the plastic. The extra-tree regression identified six key descriptors in determining OFD sales in Chinese cities. Approximately 847 kt of OFD plastic waste was generated in 2021 (per capita 1.10 kg/yr in the megacities and 0.39 kg/yr in other cities). Various additives were extensively detected, with geomean concentrations of 140.96, 4.76, and 0.25 μg/g for ∑8antioxidants, ∑21phthalates, and bisphenol A (BPA), respectively. The estimated mass inventory of these additives in the OFD plastics was 164.7 t, of which 51.1 t was released into the atmosphere via incineration plants and 51.0 t was landfilled. The incineration also released 8.07 t of polycyclic aromatic hydrocarbons and 39.1 kt of particulate matter into the atmosphere. Takeout food may increase the dietary intake of phthalates and BPA by 30% to 50% and raise concerns about considerable exposure to antioxidant transformation products. This study provides profound environmental implications for plastic waste in the Chinese OFD industry. We call for a sustainable circular economy action plan for waste disposal, but mitigating the hazardous substance content and their emissions is urgent.

Review of the Current State of Pyrolysis and Biochar Utilization in Europe: A Scientific Perspective

This scientific paper provides an overview of the current state of pyrolysis in Europe, with a focus on mapping the key research areas and technologies employed. This research relied on search equations that centered on the utilization of biomass and plastics as primary feedstocks in pyrolysis, with a particular emphasis on biochar generation and different technologies applied. The results showed that both plastic and biomass pyrolysis can contribute to reducing waste and mitigating greenhouse gas emissions. However, plastic pyrolysis can release harmful pollutants due to the presence of chlorine and other additives in plastics, which requires sophisticated emission control systems to be implemented. The production of biochar from sewage sludge is identified as a promising approach for phosphorus recovery, which can subsequently be utilized as a valuable fertilizer in agricultural applications. The data from this study contribute to exploring future applications at pilot and industrial scales for pyrolysis, with a critical assessment of the use of feedstocks. Moreover, this work provides information about current companies that are already operating on a large scale with pyrolysis and a map of the principal countries in Europe engaged in pyrolysis research, correlating the characteristics of the pyrolysis processes investigated.

Neurotoxicity of Benzotriazole Ultraviolet Stabilizers in Teleost Fishes: A Review.

Plastic additives that maintain integrity have been extensively studied for potential toxicity to fish; however, chemicals that protect polymers from (artificial) UV degradation are less studied. Benzotriazole UV stabilizers (BUVSs) are the most widely used UV stabilizers in plastics and are often used in sunscreens, cosmetics, paint, and food packaging. BUVSs can negatively affect aquatic wildlife when released into the environment via plastic degradation. In this review, we summarize the distribution of BUVSs globally and discuss neurotoxicological endpoints measured in fish to understand how these plastic additives can affect the neurological health of teleost fishes. BUVSs have been detected in aquatic environments at concentrations ranging from 0.05 up to 99,200 ng/L. Studies show that BUVSs affect behavioral responses and acetylcholinesterase activity, indicators of neurotoxicity. Our computational analysis using transcriptome data suggests certain pathways associated with neurodegeneration are responsive to exposure to BUVSs, like "Complement Activation in Alzheimer's Disease". Based on our review, we identify some research needs for future investigations: (1) molecular studies in the central nervous system to define precise mechanisms of neurotoxicity; (2) a wider range of tests for assessing aberrant behaviors given that BUVSs can affect the activity of larval zebrafish; and (3) histopathology of the nervous system to accompany biochemical analyses. These data are expected to enhance understanding of the neurotoxicity potential of benzotriazoles and other plastic additives.

Enhancing herbaceous biomass pellets quality by blending with woody biomass and plastic additives, and post-pelletization torrefaction and optimization processes: A review

Enhancing herbaceous biomass pellets quality by blending with woody biomass and plastic additives, and post-pelletization torrefaction and optimization processes: A review