Actual Wastewater Research Articles

Domestic wastewater treatment towards reuse by “self-supplied” microbial electrochemical system assisted UV/H2O2 process

Domestic wastewater is a potential source of water for non-potable reuse that may help address the global water, energy, and resource challenges. Herein, a “self-supplied” process through integrating microbial electrochemical system (MES) with UV/H2O2 was developed and investigated for wastewater treatment. H2O2 was “self-supplied” from MES while the MES catholyte was “self-supplied” from the final effluent of UV/H2O2. It was found that the MES accomplished > 80 % degradation of chemical oxygen demand (COD) through bioanode degradation, and produced 18 - 20 mg L−1 H2O2 via oxygen reduction reaction in the gas diffusion cathode. The MES effluent was further treated by the UV/H2O2 process, which achieved the complete removal of recalcitrant diclofenac and > 6 log inactivation of Escherichia coli. The enhanced treatment performance of UV/H2O2 was demonstrated via a comparison with the control experiments (UV or H2O2 treatment) and benefited from ·OH generation and sulfide removal. When treating the actual wastewater, the proposed system exhibited consistent treatment performance for the organic compounds and recalcitrant contaminants, and the quality of the treated water would meet the non-potable water reuse guidelines. The results of this study encourage the further exploration of emerging contaminant removal, system coordination, and use of renewable energy by the cooperation between MES and UV/H2O2.

Performance and analysis of kappa-carrageenan hydrogel for PFOA-contaminated soil remediation wastewater treatment

Perfluorooctanoic acid is an emerging pollutant with exceptional resistance to degradation and detrimental environmental and health impacts. Conventional physical and chemical processes for Perfluorooctanoic acid are either expensive or inefficient. This study developed an environmentally sustainable and cost-effective gravity-driven kappa-carrageenan (kC)-based hydrogel for perfluorooctanoic acid (PFOA) removal from synthetic and actual wastewater. Two kC filters were prepared by mixing activated carbon (AC) or vanillin (V) with the kC hydrogel to optimize the hydrogel selectivity and water permeability. Experimental work revealed that the PFOA rejection and water permeability increased with the AC and V concentrations in the kC hydrogel. Experiments also evaluated the impact of feed pH, PFOA concentration, hydrogel composition, and hydrogel thickness on its performance. Due to pore size shrinkage, the AC-kC and V-kC hydrogels achieved the highest PFOA rejection at pH 4, whereas the water flux decreased. Increasing the PFOA concentration reduced water flux and increased PFOA rejection. For 2 cm hydrogel thickness, the water flux of 3%kC-0.3%AC and 3%kC-3%V hydrogels was 25.6 LMH and 21.5 LMH, and the corresponding PFOA rejection was 86.9% for 3%kC-0.3%AC and 85.7% for 3%kC-3%V. Finally, the kC-0.3%AC hydrogel removed 81.1% of PFOA from wastewater of 179 mg/L initial concentration compared to 79.3% for the kC-3%V hydrogel. After three filtration cycles, the water flux decline of 3%kC-0.3%AC was less than 10%. The gravity dead-end kC hydrogel provides sustainable PFOA wastewater treatment with biodegradable and natural materials.

Multilayered alginate–hydrogel-functionalized zeolite based on ionic cross-linking composed with a certain Ca2+ and Mg2+ ratio for ammonium adsorption

To enhance ammonium removal in wastewater treatment, a novel adsorbent, multilayered ionic cross–linked alginate–hydrogel–metal-coated zeolite (Al-H-M-Z), was synthesized. Essential divalent cations, 2.60 mmol of Ca2+ and Mg2+, were incorporated into Al-H-M-Z (10 g) in a Ca2+:Mg2+ ratio of 0.73:1.85, facilitating strong alginate–polymer interactions and significantly enhancing the adsorption efficiency. Langmuir and Freundlich isotherm analyses revealed that Al-H-M-Z had a maximum adsorption capacity of 56.5 ± 8.78 mg g−1 and an adsorption intensity of 0.703 ± 0.122, which were 7.24-fold and 1.59-fold higher than those of natural zeolite (7.80 ± 1.09 mg g−1 and 0.444 ± 0.254), respectively. These enhanced properties are attributed to the modified structural and surface chemistry. The Al-H-M-Z coating exhibited a 4.76-fold increase in surface area (3.91 m2 g−1), an 8.94-fold increase in micropore volume (17.8 × 10−3 cm3 g−1), and a 4.22-fold increase in pore diameter (4.14 nm) when compared to the traditional Al-only coating. For applicability, Al-H-M-Z and Z achieved ammonium removal rates of 7.94% and 5.61%, respectively, in actual fish farm wastewater, representing a 1.41-fold improvement in adsorption efficiency after the coating process.

Performance of a novel Built-in Static Magnetic Field – Biological Aerated Filter (BSMF–BAF) for treating high-salt textile dyeing wastewater

High-salt textile dyeing wastewater is difficult to treat. Magnetic fields can enhance the biodegradation capacity and extreme environmental adaptabilities of microorganisms. Thus, magnetically enhanced bioreactors are expected to improve the treatment efficiency and stability of high-salt textile dyeing wastewater. Accordingly, a novel Built-in Static Magnetic Field – Biological Aerated Filter (BSMF–BAF) was constructed and investigated for treating actual high-salt textile dyeing wastewater in this study. Two other BAFs packed with traditional and magnetic ceramsite carriers, respectively, were simultaneously operated for comparison. The removal of color, chemical oxygen demand (COD), suspended solid (SS) and acute toxicity were monitored. The activities of key enzymes and microbial community structure were analyzed to reveal possible mechanisms for improving the treatment efficiency of traditional BAF using the BSMF. The results showed that the BSMF–BAF possessed the highest removal efficiencies of color, COD, SS and acute toxicity among the three BAFs. The BSMF induced significant increases in the activities of azoreductase and lignin peroxidase, which were responsible for the degradation of azo compounds in the wastewater and the detoxification of toxic intermediates, respectively. Additionally, the BSMF induced the relative enrichment of potentially effective bacteria and fungi, and it maintained a relatively high abundance of fungi in the microbial community, resulting in a high treatment efficiency.

Fundamental Insights into the Direct Electron Transfer Mechanism on Ag Atomic Cluster.

The nonradical oxidation pathway for pollutant degradation in Fenton-like catalysis is favorable for water treatment due to the high reaction rate and superior environmental robustness. However, precise regulation of such reactions is still restricted by our poor knowledge of underlying mechanisms, especially the correlation between metal site conformation of metal atom clusters and pollutant degradation behaviors. Herein, we investigated the electron transfer and pollutant oxidation mechanisms of atomic-level exposed Ag atom clusters (AgAC) loaded on specifically crafted nitrogen-doped porous carbon (NPC). The AgAC triggered a direct electron transfer (DET) between the terminal oxygen (Oα) of surface-activated peroxodisulfate and the electron-donating substituents-containing contaminants (EDTO-DET), rendering it 11-38 times higher degradation rate than the reported carbon-supported metal catalysts system with various single-atom active centers. Heterocyclic substituents and electron-donating groups were more conducive to degradation via the EDTO-DET system, while contaminants with high electron-absorbing capacity preferred the radical pathway. Notably, the system achieved 79.5% chemical oxygen demand (COD) removal for the treatment of actual pharmaceutical wastewater containing 1053 mg/L COD within 30 min. Our study provides valuable new insights into the Fenton-like reactions of metal atom cluster catalysts and lays an important basis for revolutionizing advanced oxidation water purification technologies.

Scalable and facile fabrication of sulfonic-acid-functionalized porous hypercrosslinked polymers for efficient recovery of rare earth elements from tailing wastewater

The separation and enrichment of rare earth elements (REEs) from tailing wastewater is of great significance for the sustainable supply of REEs and environmental remediation. As Al3+ exhibits extreme similar properties with REE3+, selective recovery of REE3+ from the sulphate tailing wastewater remains a considerable challenge. Based on the difference in the binding stability of REE3+ and Al3+ with sulfate ions, the utilization of sulfonic acid groups may provide a promising method for enhancing the selectivity of REE3+/Al3+ in the sulphate aqueous solution. Herein, a series of sulfonic-acid-functionalized hyper-crosslinked polymers (SHCP-Ps) were successfully synthesized through a facile, scalable and one-step method catalyzed by chlorosulfonic acid, which has the advantages of high sulfonic acid density (3.27 mmol/g), specific surface area (1044.6 m2/g), abundant micropores and superhydrophilicity. These properties result in SHCP-P exhibiting fast adsorption kinetics (30 min) and high adsorption capacities (106.78 mg/g (La), 111.99 mg/g (Eu) and 126.27 mg/g (Lu)). Additionally, it exhibits extremely high REE3+/Al3+ selectivity (SF(La/Al) = 6929, SF(Eu/Al) = 4810, SF(Lu/Al) = 3003) in sulfate medium, surpassing that of most existing REEs adsorbents. Upon application of SHCP-P to actual wastewater, the recovery rate of total REE3+ was observed to reach 87 %, while the adsorption rate of Al3+ was found to be 0. Simultaneously, SHCP-P exhibits both high reusability and magnification synthesis capabilities. The results indicate that SHCP-P has significant potential for industrial applications in the selective recovery of REEs from tailing wastewater.

Biomimetic heat-localized and solar absorption-enhanced hollow structural nanofibrous membrane for clean water production from saline water and dye wastewater

The rational design of material structures can be an effective approach to enhance the performance of solar-driven clean water production. In this study, a hollow structural nanofibrous membrane was developed by mimicking the hollow structure of polar bear hair using coaxial electrospinning. The shell layer consisted of carbon nanoparticles (C NPs) decorated CuO nanosheets (C@CuO), that exhibited photothermal conversion capacity. Meanwhile, the core layer containing hydrophilic polyvinylpyrrolidone (PVP) was eliminated to generate the hollow structure. The C NPs enhanced the membrane’s light absorption to increase thermal energy harvesting, while the CuO nanosheets improved the membrane’s wettability enhancing the water supply. Furthermore, the hollow structure limited air convection, prevented heat conduction, and minimized heat radiation, enabling heat localization to be achieved inside the membrane to suppress heat loss during evaporation. For 3.5 wt% saline water and actual dye wastewater, the C@CuO nanofibrous membrane achieved high evaporation rates of 1.36 kg·m−2·h−1 and 1.31 kg·m−2·h−1, respectively, under 1 sun illumination. Moreover, even after continuous 6-h evaporation tests, the evaporation rate of the C@CuO membrane remained virtually unchanged, highlighting its long-term stability with regard to salt resistance in real-world applications. Additionally, the remarkable flexibility of the C@CuO membrane offers convenience during operation and guarantees dimensional stability when it is subjected to external stresses. These discoveries should inspire subsequent research on developing delicate architectural materials and exploring their potential applications in various fields, including energy generation, clean water production, and thermal insulation.

Synthesis, performance and application of environmental protection scale inhibitorβ-CD-MA-SSS copolymer——in electric power industry

The issue of water scaling in the treatment of cooling water has become an imperative problem that should be solved urgently for the sake of safe operation in large-scale flexible DC converter stations. However, the coexistence of Ca2+ and Mg2+ in high content in this sort of pending raw water is quite hard to tackle. β-CD-MA-SSS, an eco-friendly ternary co-polymer antiscalant with good performance of inhibiting the formation of scale, was applied to address this conundrum in this paper. The efficacy of the antiscalant β-CD-MA-SSS was investigated in cooling water systems under the conditions of low hardness, low alkalinity, a temperature not exceeding 80 °C, and a pH range of 6–8. After optimization, this reagent dem onstrated an excellent scale inhibition rate up to 80% for both calcium carbonate and calcium-magnesium mixed scales. Scanning electron microscopy (SEM) analysis revealed a noticeable reduction in the size of CaCO3 particles when subjected to the action of β-CD-MA-SSS. It was postulated from FTIR analysis that nanoinpurity and chelation effects mainly contributed to the mixed scale inhibition. Further, the effect of β-CD-MA-SSS on the actual production wastewater was comprehensively evaluated from the technical, economic and environmental aspects.

Efficient chromium remediation using eco-innovative biochar in a novel two-stage upflow fixed bed system

Chromium (Cr) pollution poses a significant environmental threat. This study addresses the highly toxic hexavalent form of chromium [Cr(VI)] by developing an innovative two-stage upflow fixed-bed system. The system uses nano iron sulfide-modified biochar (nFeS-BC), derived from spent substrates of Lentinus edodes, as the primary adsorbent. The study determines the removal mechanisms by nFeS-BC, including ion exchange, functional group interaction, complexation and co-precipitation. Fixed bed experimental results demonstrated a maximum adsorption capacity (qe) of 2.751 mg·g−1 for Cr(VI) with an initial concentration (C0) of 20 mg·g−1, bed height (Z) of 10 cm, flow rate (Q) of 2 mL·min−1, and at pH 2. The adsorption process closely followed the Thomas and Yoon-Nelson models, confirming a high fitting accuracy (R2 = 0.997), which underscores the predictability and stability of nFeS-BC in dynamic flow conditions. Subsequent treatment in a second fixed bed, filled with cetyltrimethyl ammonium bromide-modified biochar (CTAB-BC), reduced the total Cr concentration to 0 mg·L−1. Furthermore, nFeS-BC retained 50 % of its initial adsorption capacity after five regeneration cycles. This study highlights the potential of nFeS-BC within a novel fixed-bed design for efficient and sustainable treatment of actual wastewater.

Bimetallic FeCu-MOF derivatives as heterogeneous catalysts with enhanced stability for electro-Fenton degradation of lisinopril

A bimetallic FeCu/NC core-shell catalyst, consisting in nanoparticles where zero-valent Fe and Cu atoms, slightly oxidized on their surface, are encapsulated by carbon has been successfully prepared by modifying the synthesis route of MIL(Fe)-88B. FeCu/NC possessed well-balanced textural and electrochemical properties. According to voltammetric responses, in-situ Fe(III) reduction to Fe(II) by low-valent Cu was feasible, whereas the high double-layer capacitance confirmed the presence of a great number of electroactive sites that was essential for continuous H2O2 activation to •OH via Fenton's reaction. Electrochemical impedance and distribution of relaxation times (DRT) analysis informed about the strong leaching resistance of FeCu/NC. To validate the promising features of this catalyst, the advanced oxidation of the antihypertensive lisinopril (LSN) was investigated for the first time. The heterogeneous electro-Fenton (HEF) treatment of 16.1 mg L−1 LSN solutions was carried out in a DSA/air-diffusion cell. At pH 3, complete degradation was achieved within 6 min using only 0.05 g L−1 FeCu/NC; at near-neutral pH, 100 % removal was also feasible even in actual urban wastewater, requiring 60–75 min. The FeCu/NC catalyst demonstrated high stability, still maintaining 86.5 % of degradation efficiency after 5 cycles and undergoing low iron leaching. It outperformed the monometallic (Fe/NC and Cu/NC) catalysts, which is explained by the Cu(0)/Cu(I)-catalyzed Fe(II) regeneration mechanism that maintains the Fenton's cycle. LC-MS/MS analysis allowed the identification of two main primary LSN by-products. It can then be concluded that the FeCu/NC-based HEF process merits to be further scaled up for wastewater treatment.

Long-range interactions driving neighboring Fe–N4 sites in Fenton-like reactions for sustainable water decontamination

Actualizing efficient and sustainable environmental catalysis is essential in global water pollution control. The single-atom Fenton-like process, as a promising technique, suffers from reducing potential environmental impacts of single-atom catalysts (SACs) synthesis and modulating functionalized species beyond the first coordination shell. Herein, we devised a high-performance SAC possessing impressive Fenton-like reactivity and extended stability by constructing abundant intrinsic topological defects within carbon planes anchored with Fe−N4 sites. Coupling atomic Fe−N4 moieties and adjacent intrinsic defects provides potent synergistic interaction. Density functional theory calculations reveal that the intrinsic defects optimize the d-band electronic structure of neighboring Fe centers through long-range interactions, consequently boosting the intrinsic activity of Fe−N4 sites. Life cycle assessment and long-term steady operation at the device level indicate promising industrial-scale treatment capability for actual wastewater. This work emphasizes the feasibility of synergistic defect engineering for refining single-atom Fenton-like chemistry and inspires rational materials design toward sustainable environmental remediation.

Multi-ligand strategy for enhanced removal of heavy metal ions by thiol-functionalized defective Zr-MOFs

Given the significant global concern about heavy metal pollution, the development of effective adsorbents to capture pollutants has become an urgent issue. In this work, thiol-functionalized defective Zr-MSA-DMSA was designed by mixing 2,3-dimercaptosuccinic acid and mercaptosuccinic acid, which was applied for the rapid and efficient removal of M(II) (i.e., Pb(II), Hg(II), Cd(II)) from wastewater. Zr-MSA-DMSA exhibited excellent adsorption performance, and the maximum adsorption capacities for Pb(II), Hg(II), and Cd(II) were 715.2 mg g−1, 862.7 mg g−1, and 450.5 mg g−1. In actual wastewater, Zr-DMSA-MSA exhibited up to 97 % M(II) removal efficiency and excellent anti-interference ability. It also maintained good structural stability after five adsorption/regeneration cycles. Thus, the abundant oxygen vacancies and unsaturated adsorption sites on Zr-MSA-DMSA significantly improved the adsorption performance of M(II). Spectral analysis and DFT calculations confirmed that Zr-MSA-DMSA mainly relied on the coordination of sulfur and oxygen atoms, electrostatic attraction and a large number of defective sites to achieve the adsorption of M(II). Fixed bed experiments showed that Zr-MSA-DMSA exhibited a depletion time of 10500 min and a volume of 7.0 L. In summary, Zr-MSA-DMSA holds significant potential for treating heavy metal wastewater and provides potential applications for defect engineering.

Hierarchical porous ACNF/MIL-68(In)–NH2 composites for rapid and efficient removal of losartan from water: Unveiling adsorption mechanisms and superior performance

Losartan (LP), a medication commonly used to treat hypertension, has emerged as a potential environmental pollutant. Despite its widespread use, research on the efficient and rapid removal of LP from the environment remains very scarce. The limited studies on LP adsorption indicate that the adsorption capacity and rate of LP need improvement. In this study, we successfully prepared a hierarchical porous nitric acid-treated carbon nanofiber (ACNF)/MIL-68(In)–NH2 composite with a robust three-dimensional support structure using a simple hydrothermal method for the first time to adsorb LP. The resulting ACNF/MIL-68(In)–NH2 composite demonstrated exceptional adsorption capabilities, achieving an equilibrium absorption capacity of 259.87 mg/g within just 64 min, significantly outperforming previously reported results. Langmuir fitting indicated a maximum theoretical adsorption capacity exceeding 630 mg/g at 55 °C. For actual wastewater with low LP concentrations, complete removal was achieved with a minimal dose of the ACNF/MIL-68(In)–NH2 adsorbent. DFT calculations and Multiwfn wavefunction analysis revealed that the adsorption behavior of LP onto ACNF/MIL-68(In)–NH2 is primarily driven by electrostatic interactions, multiple hydrogen bonds, π-π stacking interactions, and van der Waals forces. This work presents an innovative strategy for the efficient and rapid removal of residual LP from water environments.

TiO2-loaded phosphogypsum-modified biochar for the removal of ofloxacin and Cu2+: Performance, mechanisms, and toxicity assessment

The combined contamination of antibiotics and heavy metals usually occurs in aquaculture wastewater and has high ecological toxicity. Currently, most research only focuses on the removal of a single heavy metal or antibiotics, and there is little research on the simultaneous removal of both. Therefore, to effectively treat them, this study prepared TiO2-loaded phosphogypsum-modified biochar (TYBC450) for adsorption and photocatalytic removal of ofloxacin (OFL) and copper (Cu2+). The removal performance and mechanisms of OFL and Cu2+ were explored, and their ecological toxicity was assessed through zebrafish acute toxicity experiments. The results suggested a synergistic effect between OFL and Cu2+. The adsorption efficiencies of TYBC450 for OFL and Cu2+ were 88.16% and 90.87% (the adsorption capacities were 1.75 and 3.65 mg/g, respectively). Bridging, precipitation, and complexation effects were the main co-adsorption mechanisms. The photocatalytic efficiencies of OFL and Cu2+ were 91.23% and 72.09% (the rate constants were 0.0101 and 0.0045 min-1, respectively). OFL acted as a hole-trapping agent, while Cu2+ acted as an electron acceptor, hindering the combination of e- and h+. There were 12 intermediates in the OFL degradation process, which had lower toxicity than the mother organism. Both the cyclic regeneration and actual aquaculture wastewater application tests indicated that TYBC450 had potential application prospects.

Enhanced mineralization of pharmaceutical residues at circumneutral pH by heterogeneous electro-Fenton-like process with Cu/C catalyst

Conventional electro-Fenton (EF) process at acidic pH ∼3 is recognized as a highly effective strategy to degrade organic pollutants; however, homogeneous metal catalysts cannot be employed in more alkaline media. To overcome this limitation, pyrolytic derivatives from metal-organic frameworks (MOFs) have emerged as promising heterogeneous catalysts. Cu-based MOFs were prepared using trimesic acid as the organic ligand and different pyrolysis conditions, yielding a set of nano-Cu/C catalysts that were analyzed by conventional methods. Among them, XPS revealed the surface of the Cu/C-A2-Ar/H2 catalyst was slightly oxidized to Cu(I) and, combined with XRD and HRTEM data, it can be concluded that the catalyst presents a core-shell structure where metallic copper is embedded in a carbon layer. The antihistamine diphenhydramine (DPH), spiked into either synthetic Na2SO4 solutions or actual urban wastewater, was treated in an undivided electrolytic cell equipped with a DSA-Cl2 anode and a commercial air-diffusion cathode able to electrogenerate H2O2. Using Cu/C as suspended catalyst, DPH was completely degraded in both media at pH 6–8, outperforming the EF process with Fe2+ catalyst at pH 3 in terms of degradation rate and mineralization degree thanks to the absence of refractory Fe(III)-carboxylate complexes that typically decelerate the TOC abatement. From the by-products detected by GC/MS, a reaction sequence for DPH mineralization is proposed.

The insight into behavior and mechanism of chitosan-embedded hydroxyapatite gel spheres used for efficient solidification of uranium in wastewater

In this work, hydroxyapatite (HAP), an environmentally friendly material was prepared with Phosphogypsum (PG) as calcium source, and uranium immobilization gel spheres were prepared by chitosan (CS) embedding, which would reduce HAP agglomeration while providing an abundance of uranium-loving groups, realizing “treating waste for waste”. The optimum pH for U(VI) removal was determined to be 4, the optimum dosage was 0.2 g/L, and qmax = 350.88 mg/g through batch experiments. When C0 = 10 mg/L, it was found that the removal rate of U(VI) by HAP-CS could be up to 99.92 %, and the residual uranium concentration was 0.008 mg/L, which meets the national emission standard. The removal rate of uranium can reach 95.92 % by applying it to high concentration uranium ore wastewater. CS was found to have good biocompatibility with HAP by SEM, FTIR, XRD, and XPS characterization. Meanwhile, we found that Ca, –OH, and P-O play a dominant role in the uranium removal process, and the main mechanism of uranium removal by Hydroxyapatite-Chitosan gel spheres (HAP-CS) is surface complexation, ion exchange, and dissolution–precipitation binding. The HAP-CS has high uranium removal efficiency, simple solid–liquid separation, and good biocompatibility, and can be used to treat actual uranium-containing wastewater.

Efficient hydrogen peroxide synthesis with Pluggable Capsule cathode for Electro-Fenton treating actual landfill leachate

Membrane concentrate of landfill leachate is the typical refractory wastewater with high contaminants concentration, high complexity, and high toxicity, posing a huge potential threat to the surface and subsurface water. Electro-Fenton (EF) based on in-situ synthesis of H2O2 is an effective method for the treatment of refractory organic pollutants. However, the low accumulative concentration of H2O2 and the poor scalability of the system remain major bottlenecks, limiting the practical application of EF. This study presented a modular air-breathing cathode, Pluggable Capsule Cathode (PCC), for efficient in-situ H2O2 synthesis through 2-electron oxygen reduction reaction (ORR). Based on PCC, corridor reactors (CR) were fabricated for in-situ H2O2 synthesis and actual landfill leachate treatment. Operated under the optimal conditions (dual-chamber, A/V=240 cm2 L−1, 2 M NaOH electrolytes and J=20 mA cm−2), the H2O2 concentration reached 28.1 g/L. In the EF system based on single-chamber CR equipped with PCCs, 81 % of COD and 89 % of NH3-N in landfill leachate were removed within 3 h. The total cost of landfill leachate treatment by the EF system based on CR-PCC was calculated as $ 5.06 m−3. The PCC based EF system was a promising process for the treatment of actual refractory wastewater, which provides a new insight for the structure design of cathode and reactor in the future.

A two-dimensional cobalt-based metal–organic framework efficiently adsorbs Cr(VI) from wastewater

Metal-organic frameworks (MOFs) display multi-level pores and abundant adsorption sites, which can effectively adsorb Cr(VI) from wastewater. In this paper, x-ray single crystal diffraction analysis showed that both the N atom and two carboxyl groups in L2− of [Co(L)(H2O)2]n (1) (H2L = 3, 5-pyridinedicarboxylic acid) underwent coordination reactions with Co(II) in μ3-η1:η1:η1 fashion, giving rise to the formation of a two-dimensional structure. The nano adsorbent of 1 (2D-Co-MOF-N) with a particle diameter about 100 nm was successfully prepared by cell disruption method. The optimal conditions for 2D-Co-MOF-N to adsorb Cr(VI) from wastewater were observed at pH 6.5, T = 30 °C, and a dosage of 0.10 g/L, achieving a maximum adsorption capacity of 207.93 mg/g which was better than most MOFs adsorbents. The present of Cl−, NO3–, SO42−, and PO43− in wastewater inhibited the adsorption of Cr(VI) by 2D-Co-MOF-N due to competitive adsorption. Cycling experiments showed that 2D-Co-MOF-N exhibited admirable structural and performance stability, which could be deemed as a potential candidate for the removal toxic ions from actual wastewater.

Evaluation of a Greenhouse Ecosystem to Treat Craft Beverage Wastewater

An aerated greenhouse ecosystem, often referred to as a Living Machine®, is a technology for biological wastewater treatment within a greenhouse structure that uses plants with their roots submerged in the wastewater. This system has a small footprint relative to traditional onsite wastewater treatment systems and constructed wetland, can treat high-strength wastewater, and can provide a high level of treatment to allow for reuse for purposes such as irrigation, toilet flushing, and landscape irrigation. Synthetic and actual craft beverage wastewaters (wastewater from wineries, breweries, and cideries) were examined for their treatability in bench-scale greenhouse ecosystems. The tested wastewater was high strength with chemical oxygen demands (COD) concentrations of 1120 to 15,000 mg/L, total nitrogen (TN) concentrations of 3 to 45 mg/L, and total phosphorus (TP) concentrations of 2.3 to 90 mg/L. The COD, TN, and TP concentrations after treatment ranged from below 125 to 560 mg/L, 1.5 to 15 mg/L, and below 0.25 to 7.8 mg/L, respectively. The results confirm the ability of the aerated greenhouse ecosystem to be a viable treatment system for craft beverage wastewater and it is estimated to require 54 and 26% lower hydraulic retention time than an aerobic lagoon and a low temperature, constructed wetland, respectively, the types of systems that would likely be used for this type of wastewater for onsite locations.

Porous sodium alginate/cellulose nanofiber composite hydrogel microspheres for heavy metal removal in wastewater

High adsorption capacity, high adsorption rate and reusable adsorbents are urgent needed for removing heavy metals from wastewater. In this study, porous sodium alginate/cellulose nanofiber (SA/CNF) composite hydrogel microspheres were prepared by combining sodium alginate with cellulose nanofibers by microfluidics technology and adding polyethylene glycol (PEG) as pore making agent. The SA/CNF composite hydrogel microspheres could efficiently adsorb heavy metals (Pb2+, Cu2+ and Cd2+) in wastewater. The influencing factors of adsorption process, including pH, temperature, initial concentration, coexisting ions and aquatic environments, were systematically discussed. The adsorption process was more consistent with Langmuir isotherm model and pseudo-second-order model in batch system, indicating the adsorption process was mainly chemical adsorption. The adsorption capacity to Pb2+ obtained by Langmuir model was as high as 544.66 mg/g at 20 °C. Fixed-bed column adsorption experiments demonstrated the excellent performance of the as-prepared SA/CNF microspheres for treatment of the flowing wastewater in a column system. Overall, a highly practical adsorption process based on hydrogel adsorbents was developed for the removal of heavy metals from actual wastewater.