Active Electrode Materials Research Articles

Construction of CuCo2O4 hollow microspheres/Ti3C2Tx MXene composite for electrode material of hybrid supercapacitors

CuCo2O4 is a promising active electrode material for its considerable theoretical capacities and natural abundance, however, also is plagued by the disadvantages of the intrinsic low electrical conductivity, slow reaction kinetics and relatively low specific capacity in the practical applications, hence, the precise hybridization with high conductivity and active surface matrix is a promising strategy to overcome these limitations. Herein, porous CuCo2O4 hollow microspheres (CuCo2O4-HS) with the diameter of about 500 nm are hybridized with Ti3C2Tx MXene nanosheets (CuCo2O4-HS/MXene) by electrostatic self-assembly. The crystal structure, morphology and elemental composition of prepared CuCo2O4-HS/MXene are confirmed by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). Electrochemical test results show that the CuCo2O4-HS/MXene-3 electrode delivers an outstanding specific capacity of 1341.4 C g−1 at 1 A g−1 and retained excellent cyclic stability of 90.9% retention during 10000 cycles of charge/discharge at 5 A g−1. Additionally, the hybrid supercapacitors (HSC) device from CuCo2O4-HS/MXene-3 demonstrated excellent specific energy of 66.3 Wh kg−1 and 49.8 W h kg−1 at specific power of 724.3 W kg−1 and 7229.8 W kg−1 respectively. Significantly, two HSCs connected in series can light a commercial blue LED (3 V) for about 10 mins, demonstrating promising prospect for practical applications.

Synergy of structural engineering and VO2 self-transformation enables ultra-high areal capacity cathodes for zinc-ion batteries

The development of cathodes with high areal capacities is a prerequisite for realizing the practical application of zinc-ion batteries (ZIBs). However, the slow ion (de)intercalation kinetics and the highly tortuous ion transport channels in the traditionally blade-coated electrodes limit the practical areal capacities of the ZIB cathodes below 3 mAh cm−2. In this work, multi-stage pore structures, including through-holes perpendicular to the electrode and submicron-scale channels along the radial direction of the printed filaments, are obtained through polyvinylidene difluoride (PVDF) phase separation assisted 3D printing procedure. In this novel electrode material, the porous network enables fast electron/ion transport and improves the accessibility of active materials for thick electrodes with high active material loadings. More importantly, a phase self-transformation of VO2 to a high oxidation state of V5O12∙6H2O is achieved by regulating the charging voltage, which significantly enhances the zinc storage capacity and provides smoother channels for fast ion (de)intercalation. With these unique features, the 3D printed VO2 cathode with a mass loading of 8.9 mg cm−2 demonstrates a high specific capacity of 478.1 mAh g−1 at 1 A g−1 and a stable life cycle for 1000 cycles at 4 A g−1. When the mass loading is increased to 29.6 mg cm−2, the electrode is still able to deliver an ultra-high areal capacity of 16.8 mAh cm−2. The strategies adopted in this work greatly boost up the performance of VO2 cathodes, especially the high areal capacity, by combining structural engineering and material activity regulation.

Organic Electrode Materials for Energy Storage and Conversion: Mechanism, Characteristics, and Applications.

ConspectusLithium ion batteries (LIBs) with inorganic intercalation compounds as electrode active materials have become an indispensable part of human life. However, the rapid increase in their annual production raises concerns about limited mineral reserves and related environmental issues. Therefore, organic electrode materials (OEMs) for rechargeable batteries have once again come into the focus of researchers because of their design flexibility, sustainability, and environmental compatibility. Compared with conventional inorganic cathode materials for Li ion batteries, OEMs possess some unique characteristics including flexible molecular structure, weak intermolecular interaction, being highly soluble in electrolytes, and moderate electrochemical potentials. These unique characteristics make OEMs suitable for applications in multivalent ion batteries, low-temperature batteries, redox flow batteries, and decoupled water electrolysis. Specifically, the flexible molecular structure and weak intermolecular interaction of OEMs make multivalent ions easily accessible to the redox sites of OEMs and facilitate the desolvation process on the redox site, thus improving the low-temperature performance, while the highly soluble nature enables OEMs as redox couples for aqueous redox flow batteries. Finally, the moderate electrochemical potential and reversible proton storage and release of OEMs make them suitable as redox mediators for water electrolysis. Over the past ten years, although various new OEMs have been developed for Li-organic batteries, Na-organic batteries, Zn-organic batteries, and other battery systems, batteries with OEMs still face many challenges, such as poor cycle stability, inferior energy density, and limited rate capability. Therefore, previous reviews of OEMs mainly focused on organic molecular design for organic batteries or strategies to improve the electrochemical performance of OEMs. A comprehensive review to explore the characteristics of OEMs and establish the correlation between these characteristics and their specific application in energy storage and conversion is still lacking.In this Account, we initially provide an overview of the sustainability and environmental friendliness of OEMs for energy storage and conversion. Subsequently, we summarize the charge storage mechanisms of the different types of OEMs. Thereafter, we explore the characteristics of OEMs in comparison with conventional inorganic intercalation compounds including their structural flexibility, high solubility in the electrolyte, and appropriate electrochemical potential in order to establish the correlations between their characteristics and potential applications. Unlike previous reviews that mainly introduce the electrochemical performance progress of different organic batteries, this Account specifically focuses on some exceptional applications of OEMs corresponding to the characteristics of organic electrode materials in energy storage and conversion, as previously published by our groups. These applications include monovalent ion batteries, multivalent ion batteries, low-temperature batteries, redox flow batteries with soluble OEMs, and decoupled water electrolysis employing organic electrodes as redox mediators. We hope that this Account will make an invaluable contribution to the development of organic electrode materials for next-generation batteries and help to unlock a world of potential energy storage applications.

Application of nanotechnology in the battery of electric vehicles

Application of nanotechnology in the battery of electric vehicles

Enhanced supercapacitive performance of lead vanadate hybrid architect on nickel foam with machine learning-driven capacitance prediction

The structural and chemical architecture of the active electrode material must provide an optimum environment for charge storage as well as stability to provide crucial supercapacitance properties. In this study, we developed a binder-free protocol to obtain an optimized polymorph of lead vanadate (PbV) with a unique hybrid architecture on nickel foam for hybrid supercapacitor applications. Furthermore, a detailed capacitance power prediction model is proposed based on several machine learning and recurrent neural network methods to improve the reliability of the fabricated hybrid supercapacitor. Specifically, recursive feature elimination is implemented to alleviate the problems of overfitting and the curse of dimensionality by identifying and eliminating extraneous characteristics while determining the appropriate features of the capacitance power. The experimental observations are validated by DFT analysis concerning the role of oxygen vacancies for the improvement of electrical characteristics. Ultimately, the fabricated energy storage device exhibits impressive energy and power densities of 26.18 Whkg−1 and 6−1, respectively. Importantly, the predicted results confirm that the long-short-term memory network provides excellent results for capacitance prediction of hybrid supercapacitors with R2 = 0.83 in the test set and synthesized sample prediction with a mean absolute error of 20.37.

Efficient green combustion production of pure nickel oxide (NiO) and silver-doped NiO nanoparticles using Aloe Vera gel extract: Its supercapacitors applications

This study employs the synthesis of pure NiO and Ag-doped NiO with varying concentrations (1, 3, 5, 7 and 9 mol%) of Ag2O nanoparticles by solution combustion method. The Structural and morphology of nanomaterials were elucidated by analytical spectroscopic methods. XRD revealed alterations in physical properties, such as crystallite size and lattice parameters, of NiO nanoparticles due to the presence of Ag2O. UV-Vis spectroscopy demonstrated a reduction in the bandgap from 3.41 eV (pure NiO) to 3.21 eV for 1, 3, 5, 7 and 9 mol% Ag2O-doped NiONPs. To assess their viability as active electrode materials in supercapacitors, the synthesized samples were subjected to analysis in a 0.1 M HCl electrolyte. Electrochemical studies done through various tests, including Electrochemical-Impedance, Cyclic-Voltammetry and Galvanic Charge-Discharge. Remarkably, the 5 mol% Ag2O-doped NiO in a 3-electrode system exhibited a notable capacitance value of 248 Fg−1 at a scan rate of 5 Ag−1. Additionally, it demonstrated robust cycling stability, maintaining over 90% of the original capacitance after 2000 cycles in GCD studies. The potential chemical interaction between nanoscale Ag2O and NiO could be responsible for the enhanced capacitance. These findings offer valuable insights for researchers exploring the development of novel electrode materials for energy-storage devices.

Time-dependent synthesis of tungsten disulfide for flexible supercapacitors

Tungsten disulfide (WS2) with various nanostructures was synthesized for times ranging from 6 to 72 h, using a simple and easy hydrothermal technique, for high-performance supercapacitor applications. The synthesized WS2 for 24 h (WS2–24), among other synthesized WS2, exhibited flower-like structures, composed of numerous nanosheets, demonstrating superior electrochemical properties in terms of electrochemical surface area, charge transfer resistance, specific capacitance, and rate capability. In addition, WS2–24 was coated on a flexible activated carbon cloth substrate to make flexible electrodes and assemble a flexible symmetric supercapacitor with a gel electrolyte. The flexible supercapacitor exhibited a specific capacitance of 262.5 F g−1 at 1 A g−1 with an energy density of 23.6 Wh kg−1 and a power density of 802 W kg−1. It also showed excellent capacitance retention of 94.5 % and a Coulombic efficiency of 86.4 % after 5000 cycles. The remarkable electrochemical properties of the synthesized WS2 materials highlight them as highly effective active materials for high-performance supercapacitor electrodes.

AB-type dual-phase high-entropy alloys as negative electrode of Ni-MH batteries: Impact of interphases on electrochemical performance

High-entropy alloys (HEAs) and their corresponding high-entropy hydrides are new potential candidates for negative electrode materials of nickel-metal hydride (Ni-MH) batteries. This study investigates the cyclic electrochemical hydrogen storage performance of two AB-type HEAs (A: hydride-forming elements, B: non-hydride-forming elements) in Ni-MH batteries. TiV2ZrCrMnFeNi with a dual-phase structure shows a fast activation and a low charge transfer impedance with a discharge capacity of 150 mAhg−1, while TiV1.5Zr1.5CrMnFeNi with a single phase shows a slow activation and a capacity of only 60 mAhg−1. The better electrochemical performance of TiV2ZrCrMnFeNi was attributed to its higher vanadium/zirconium ratio and abundant interphase boundaries, which act as hydrogen paths and heterogeneous hydride nucleation sites. These results suggest the high potential of dual-phase HEAs as new active electrode materials for Ni-MH batteries.

Mass scale synthesis of graphene nanosheets using waste cardboard for application in perovskite solar cells and supercapacitors

Advanced graphene-based materials have been proficiently incorporated into next-generation solar cells and supercapacitors because of their high electrical conductivity, large surface area, excellent charge-transport ability, and exceptional optical properties. Herein, we report the synthesis of graphene nanosheets (GNs) from waste cardboard via pyrolysis, with ethyl alcohol as the growth initiator. Additionally, we demonstrated the use of GNs in energy conversion and storage applications. Using the GN electrode in perovskite solar cells resulted in an excellent power conversion efficiency of ∼10.41 % for an active area of 1 cm2, indicating an enhancement of approximately 27 % compared to conventional electrodes. Furthermore, the GNs were used as active electrode materials in supercapacitors with excellent electrochemical performance and a high gravimetric specific capacitance of 167.5 F/g at a scan rate of 2 mV/s. The developed GNs can be efficiently used for energy storage, conversion, and electrochemical sensing applications.

Highly stable MXene/g-PPy@sulfonated cellulose composite electrodes for flexible supercapacitors

Traditional two-dimensional transition metal carbides/nitrides (MXene) have gained much academic concern due to their excellent physicochemical properties, but their susceptibility to self-stacking leads to poor cyclic stability. In this paper, an MXene-based electrode active material was successfully prepared. The generated modified PPy (g-PPy) increases the active site, increases the accessibility of ions, and can give full play to the pseudocapacitance. By the combination of modified PPy (g-PPy) nanoparticles with pseudocapacitive behavior polymerized in situ on sulfonated cellulose (SC) and MXene, not only the electrochemical performance was improved by exploiting the synergy between different electrode materials and different energy storage mechanisms, but also the MXene as a skeleton limited the volume expansion and contraction of PPy during charge/discharge cycles and the g-PPy and SC composites (g-PPy@SC) as a spacer supported the MXene layer, resulting in much higher cycle stability. Cycle stability of 98.4 % even after 10,000 cycle tests. In addition, a symmetric supercapacitor assembled from this electrode material maintains a stability of 84.4 % under 10,000 cycles at a low temperature of −40 °C. Therefore, this study provides a feasible method for the preparation of MXene-based electrodes with high cycling stability.

External Pressure in Polymer-Based Lithium Metal Batteries: An Often-Neglected Criterion When Evaluating Cycling Performance?

Solid-state batteries based on lithium metal anodes, solid electrolytes, and composite cathodes constitute a promising battery concept for achieving high energy density. Charge carrier transport within the cells is governed by solid-solid contacts, emphasizing the importance of well-designed interfaces. A key parameter for enhancing the interfacial contacts among electrode active materials and electrolytes comprises externally applied pressure onto the cell stack, particularly in the case of ceramic electrolytes. Reports exploring the impact of external pressure on polymer-based cells are, however, scarce due to overall better wetting behavior. In this work, the consequences of externally applied pressure in view of key performance indicators, including cell longevity, rate capability, and limiting current density in single-layer pouch-type NMC622||Li cells, are evaluated employing cross-linked poly(ethylene oxide), xPEO, and cross-linked cyclodextrin grafted poly(caprolactone), xGCD-PCL. Notably, externally applied pressure substantially changes the cell's electrochemical cycling performance, strongly depending on the mechanical properties of the considered polymers. Higher external pressure potentially enhances electrode-electrolyte interfaces, thereby boosting the rate capability of pouch-type cells, despite the fact that the cell longevity may be reduced upon plastic deformation of the polymer electrolytes when passing beyond intrinsic thresholds of compressive stress. For the softer xGCD-PCL membrane, cycling of cells is only feasible in the absence of external pressure, whereas in the case of xPEO, a trade-off between enhanced rate capability and minimal membrane deformation is achieved at cell pressures of ≤0.43 MPa, which is considerably lower and more practical compared to cells employing ceramic electrolytes with ≥5 MPa external pressure.

Advancing Post‐Secondary Batteries under Lean Electrolyte Conditions through Interfacial Modification Strategies

AbstractIn response to the growing global demand for portable electronics and electric vehicles, there is an escalating interest in developing advanced battery technologies with superior energy density. Research efforts are focused on unveiling post‐lithium‐ion batteries (LIBs) that outperform the performance of current LIBs through the use of innovative active electrode materials. Yet, these technological advancements face significant hurdles, primarily due to intricate interfacial issues within battery components. In laboratory‐scale studies, these challenges often lead to the utilization of excess electrolytes, which complicates the precise evaluation of battery performance. This review emphasizes the significance of designing future batteries that operate effectively under lean electrolyte usage conditions. It discusses essential principles, obstacles, and diverse strategies for interfacial modification, including in situ growth, coating of supportive layers, and embedding of active substances in pre‐structured templates. Furthermore, it compiles and examines data on the lean electrolyte conditions achieved in various battery systems, contrasting their energy densities with those of commercially established batteries. Ultimately, the potential of future batteries to achieve or even exceed the energy densities of existing commercial batteries is assessed, thereby offering a strategic roadmap for the progression of next‐generation battery technologies.

Mesoscale mechanical models for active materials in lithium-ion batteries using the multi-particle finite element method

The stability and mechanical integrity of electrode active materials have a significant impact on the safety and performance of lithium-ion batteries (LIBs). The study of mechanical properties of active materials is crucial for the safety design of batteries. Researchers have conducted several models for describing the mechanical behavior of active materials. However, an accurate mechanical model that can reflect the packing structure of active particles and achieve the multiscale mechanical analysis of active materials is still lacking. To bridge this gap, a three-dimensional (3D) mesoscopic model based on the multi-particle finite element method (MPFEM) is proposed in the present study. The numerical simulation results show that the established model is in good agreement with the experimental results for the description of the compression behavior of the active material. Based on the model, the effects of various factors on the mechanical behavior of the active materials are analyzed. The results deepen the understanding of the multiscale mechanical behavior of anode active materials and provide fundamental insights for the future development of safety design for LIBs.

Exploring Carbonization Temperature to Create Closed Pores for Hard Carbon as High-Performance Sodium-Ion Battery Anodes.

Biomass-derived porous carbon materials are meaningful to employ as a hard carbon precursor for anode materials of sodium-ion batteries (SIBs) from a sustainability perspective. Here, a straightforward approach is proposed to develop rich closed pores in pinenut-derived carbon, with the aim of improving Na+ plateau storage by adjusting the pyrolysis temperature. The optimized sample, namely the pinenut-derived carbon at 1300 °C, demonstrates remarkable reversible specific capacity of 278 mAh g-1, along with a high initial Coulomb efficiency of 85% and robust cycling stability (with a capacity retention of 89% after 800 cycles at 0.2 A g-1). In situ and ex situ analyses unveil that the developed closed pores play a significant role in enhancing the plateau capacity, providing compelling evidence for the "adsorption-filling" mechanism. Moreover, the corresponding full-cell achieves a high energy density of 245.7Wh kg-1 (based on the total weight of both electrode active materials) and exhibits outstanding rate capability (191.4 mAh g-1 at 3 A g-1).

Lithium loss, resistance growth, electrode expansion, gas evolution, and Li plating: Analyzing performance and failure of commercial large-format NMC-Gr lithium-ion pouch cells

Analysis of the performance evolution and failure mechanisms of commercial Li-ion batteries is crucial for improving testing methods, accurately modeling battery performance, and ensuring safe battery operation. Here, we present the results of a 2-year aging study conducted on commercial large-format LiNiMnCoO2-graphite pouch cells. Loss of lithium inventory (LLI) and loss of positive electrode active material (LAMPE) are shown to dominate capacity fade, as quantified by differential voltage-capacity analysis; only a small amount of LAMPE was measured in extracted electrode material, indicating that LAMPE in full cells was due to electrode dry-out. Resistance evolution, observed by direct current pulses and electrochemical impedance spectroscopy analyzed using the distribution of relaxation times, shows complex trends. Particle cracking and electrode expansion is theorized to cause most changes to resistance. Post-mortem measurements reveal a 10% increase in electrode stack thickness and substantial gas generation, with lithium plating observed in extreme cycling conditions, causing large resistance increases. Circumstantial evidence for self-discharge via redox shuttle, which decomposes the electrolyte, is shown. Overall, electrolyte stability was determined to be the limiting factor for cell lifetime. The impacts of many degradation mechanisms on diagnostic signals substantially overlap, making it challenging to monitor cell health and safety.

Ternary nanocomposite of RAFT‐polymerized DMAEMA‐functionalized graphene oxide, manganese dioxide and polyaniline as active electrode material for supercapacitor

AbstractGraphene and its derivatives are promising energy storage devices due to their high specific surface area, chemical and thermal durability and high charge transfer power. Still, their stacking and aggregate behavior can limit their practical application. To address this issue, reversible addition–fragmentation chain‐transfer (RAFT) polymerization as controlled radical polymerization was applied to functionalize the surface of graphene oxide with poly(N,N‐dimethylaminoethyl methacrylate) (PDMAEMA) via the ‘grafting from’ method. This strategy enhances the distance between graphene sheets by occupying physical volume while improving effective charge transfer through tertiary amine groups participating in the doping process. X‐ray diffraction was used to determine interlayer spacing after polymer grafting, which increased from 0.28 to 1.71 nm after polymer grafting. The hybridization of materials with diverse properties was used to enhance charge transfer capability for supercapacitor applications. PDMAEMA‐functionalized graphene oxide, nano‐manganese dioxide and polyaniline were combined to create a successful nanocomposite as electrode active material. The morphological structure and chemical composition of the synthesized nanocomposite were analyzed, and its electrochemical performance was evaluated using cyclic voltammetry, galvanostatic charge–discharge and electrochemical impedance spectroscopy. The nanocomposite exhibited a maximum specific capacitance, energy density and power density of 364.72 F g−1 (at a scan rate of 50 mV s−1), 239.08 Wh kg−1 and 678.34 W kg−1, respectively. The final nanocomposite's energy storage capacity significantly increased compared to the individual components due to hybridization's synergistic impact, reducing charge transfer resistance. © 2024 Society of Industrial Chemistry.

MnO2/AgNPs Composite as Flexible Electrode Material for Solid-State Hybrid Supercapacitor

A MnO2/AgNP nanocomposite was synthesized using a sonochemical method and investigated as an electrode material in a solid-state hybrid supercapacitor. Aquivion’s sodium and lithium electrolyte membrane serves as an electrolyte and separator. For comparison, MnO2 was used as the active material. The developed supercapacitor containing a carbon xerogel as a negative electrode, the MnO2/AgNP composite as a positive electrode and a Na+-exchange membrane demonstrated the highest performance characteristics. These results indicate that the incorporation of silver nanoparticles into the MnO2 structure is a prospect for obtaining an active composite electrode material for solid-state supercapacitors.

Enhanced Cathode Performance in Pr0.5Sr0.5FeO3-δ of Perovskite Catalytic Materials via Doping with VB Subgroup Elements (V, Nb, and Ta).

Perovskite-style materials are cathode systems known for their stability in solid oxide fuel cells (SOFCs). Pr0.5Sr0.5FeO3-δ (PSF) exhibits excellent electrode performance in perovskite cathode systems at high temperatures. Via VB subgroup metals (V, Nb, and Ta) modifying the B-site, the oxidation and spin states of iron elements can be adjusted, thereby ultimately adjusting the cathode's physicochemical properties. Theoretical predictions indicate that PSF has poor stability, but the relative arrangement of the three elements on the B-site can significantly improve this material's properties. The modification of Nb has a large effect on the stability of PSF cathode materials, reaching a level of -2.746 eV. The surface structure of PSF becomes slightly more stable with an increase in the percentage of oxygen vacancy structures, but the structural instability persists. Furthermore, the differential charge density distribution and adsorption state density of the three modified cathode materials validate our adsorption energy prediction results. The initial and final states of the VB subgroup metal-doped PSF indicate that PSFN is more likely to complete the cathode surface adsorption reaction. Interestingly, XRD and EDX characterization are performed on the synthesized pure and Nb-doped PSF material, which show the orthorhombic crystal system of the composite theoretical model structure and subsequent experimental components. Although PSF exhibits strong catalytic activity, it is highly prone to decomposition and instability at high temperatures. Furthermore, PSFN, with the introduction of Nb, shows greater stability and can maintain its activity for the ORR. EIS testing clearly indicates that Nb most significantly improves the cathode. The consistency between the theoretical predictions and experimental validations indicates that Nb-doped PSF is a stable and highly active cathode electrode material with excellent catalytic activity.

Flow electrode capacitive desalination of industrial RO reject.

Flow electrode capacitive deionization (FCDI) is a promising technology for efficiently treating industrial brine with high salt content. However, its desalination performance is currently limited by internal resistance. Achieving an effective FCDI system relies on active electrode materials with high conductivity. This study compares the desalination performances of the widely used flow electrode activated carbon (AC) with more conductive materials, reduced graphene oxide (rGO), and ZnO/rGO composite. Additionally, the lack of particle-to-particle contact in the flow electrode contributes to internal resistance and to address this, a cationic surface-active agent is introduced. This agent forms a stable dispersion, creating a space for enhanced mass loading of the active material. This modification enhances the conductive network and particle contact, reducing the diffusion path and promoting rapid ion transport. With a 5 wt% loading, ZnO/rGO achieved a 73% salt removal efficiency, surpassing AC at 63%. Furthermore, the surfactant-modified ZnO/rGO flow electrode with a 7 wt% loading demonstrated an 81% salt removal efficiency.

Challenges of Predicting Temperature Dependent Capacity Loss Using the Example of NMC-LMO Lithium-Ion Battery Cells

In semi-empirical aging modeling of lithium ion-batteries an Arrhenius approach is commonly applied to describe the temperature dependency of a linear capacity loss. However, this dependency can change with degradation modes which was also observed in this cyclic aging study on NMC111-LMO graphite pouch cells in a temperature range of 4 °C to 48 °C. By means of differential voltage analysis and post-mortem analysis we correlated different regimes in capacity loss to degradation modes and aging mechanisms. In the first regime, a power dependency of time was observed. A second accelerated linear regime which followed an increase in loss of active material of the positive electrode was seen for medium (∼19 °C to 25 °C) to high aging temperatures. Transition metal dissolution was suggested to cause accelerated SEI growth. An activation energy could be estimated to 0.83 eV (± 0.17 eV, 95% CI). Finally, at aging temperatures around 45 °C we propose decreased charge transfer kinetics to result in mossy dendrites on the negative electrode which cause a final knee in aging trajectory. The findings highlight the necessity of sufficient aging temperatures and testing time.