Acrylic Bars Research Articles

Effect of Silica Nanoparticles On Flexural Strength And Surface Hardness Of Heat Polymerized Acrylic Resin.

Statement of problem. Various studies are present to increase the strength and surface hardness of heat polymerized acrylic resin by addition of material or surface treatments. The present study to evaluate an effect of silica nanoparticles on flexural strength and surface hardness of heat polymerized acrylic resin. Purpose. The purpose of this study was effect of silica nanoparticles, incorporated into Polymethyl Methacrylate, on flexural strength and surface hardness. The present study compared the effect of silanated and non silanated silica nanoparticles on the flexural strength and surface hardness of heat polymerized acrylic resin. Material and Methods. A total of 270 acrylic bars were fabricated, in two batches of 135 each, for testing flexural strength by universal testing machine and surface hardness determined using a digital micro Vickers hardness tester. The control group and subgroups had a sample size of 15 each with varied concentrations of nanoparticles by weight. The fabricated samples were tested for flexural strength and surface hardness. Results. Flexural strength was highest for PMMA (Polymethyl methacrylate) with 0.5% silanated silica nano particles as fillers. In both the groups, the flexural strength decreased with increase in filler concentration. Surface hardness was highest in the PMMA group with non-silanated nano particles as fillers at 5% concentration. In both groups the surface hardness improved with an increase in filler concentration. ANOVA and TUKEY’s HSD test were used. P<0.05 was considered statistically significant. Conclusion. Lower concentrations of surface-treated silica nanoparticles should be used as fillers to enhance the flexural strength of commercially available heat polymerized acrylic resin. Bangladesh Journal of Medical Science Vol.23 (Special Issue) 2024 p.S79-S86

Patellar Tendon Repair Using a Patellar Tendon Allograft and External Fixator in Three Dogs

Abstract Objective The aim of this study was to report on complications and outcomes with repair of ruptured canine patellar tendons using primary tenorrhaphy coupled with patellar tendon allograft transplantation and use of a transarticular external skeletal fixator. Materials and Methods This report includes three dogs with acutely ruptured patellar tendons, all of whom had surgical repair using a patellar tendon allograft. Dogs were assessed postoperatively by physical examination, owner input, and/or video review. Functional outcomes were classified as full, acceptable, or unacceptable based on previously established criteria. Results Follow-up time was between 24 and 46 weeks. Two dogs obtained full function and one dog reached acceptable function. The acrylic connecting bars of the external fixator fractured and needed to be replaced in one dog. There were no other problems or complications. There was no evidence of rejection of any allograft. Clinical Significance Primary tenorrhaphy supported by patellar tendon allograft transplantation and transarticular skeletal fixation appears to be a viable option without evidence of patellar tendon allograft rejection and acceptable or full recovery in the three dogs of this report.

Non-contact measurement of impact load due to collision of ferromagnetic projectile based on electromagnetic induction

A non-contact measurement method of the impact load due to collision of a ferromagnetic projectile with a non-magnetic target was proposed and validated by conducting steel bar collision tests with an acrylic bar. In the measurement system, one coil connected to a stabilized power supply was set near the collision point to generate a magnetic field and the other was set near the magnet coil to measure the electromotive force induced by the disturbance of the magnetic field due to passing a ferromagnetic projectile through the coils. Because the induced electromotive force is proportional to the projectile velocity in accordance with Faraday's law of electromagnetic induction, the measured velocity of the projectile was differentiated to obtain the acceleration, which was then multiplied by the mass of the projectile to analyze the impact load. In the tests, a steel bar was collided with an acrylic bar to determine how well the proposed method could measure the impact load. The impact load analyzed from the electromotive force was compared with the impact load measured by strain gauges set on the acrylic bar and the two were found to be in good agreement. These results demonstrate that the proposed method is effective for measuring the impact load resulting from collision of a small projectile, where conventional sensors are not applicable.

An Alternative Incorporation Technique for Minimizing Complications in Attachment-Retained Implant Mandibular Overdentures: Technical Report.

The present technical report aimed to display an alternative incorporation method for ball/stud attachments in mandibular implant overdentures (MIO) to prevent or minimize metal housing debonding and attachment malpositioning. Precoating of metal housings with auto-polymerizing acrylic resin (AAR) and fabrication of straight AAR bars onto metal housings for optimal parallelism were used as new techniques. The glossy flat surfaces of metal housings (matrices) were sandblasted and precoated with a thin layer of AAR in the laboratory. Straight acrylic resin bars (3 cm long and 3 mm in diameter) were obtained and attached to these flat metal housing surfaces using a surveyor. The metal housings carrying the AAR bars were then placed intraorally onto ball/stud attachments, accurately positioned parallel to each other, and perpendicular to the long axes of implants and bound to the MIO with AAR.

Comparison of torsional properties between a Fixateur Externe du Service de Santé des Armées and an acrylic tie-in external skeletal fixator in a red-tailed hawk (Buteo jamaicensis) synthetic tibiotarsal bone model.

To compare the torsional mechanical properties of 2 external skeletal fixators (ESFs) placed with 2 intramedullary pin (IP) and transfixation pin (TP) size combinations in a model of raptor tibiotarsal bone fracture. 24 ESF-synthetic tibiotarsal bone model (polyoxymethylene) constructs. Synthetic bone models were fabricated with an 8-mm (simulated fracture) gap. Four types of ESF-synthetic bone model constructs (6/group) were tested: a FESSA with a 1.6-mm IP and 1.6-mm TPs, a FESSA with a 2.0-mm IP and 1.1-mm TPs, an acrylic connecting bar with a 1.6-mm IP and 1.6-mm TPs, and an acrylic connecting bar with a 2.0-mm IP and 1.1-mm TPs. Models were rotated in torsion (5°/s) to failure or the machine angle limit (80°). Mechanical variables at yield and at failure were determined from load deformation curves. Effects of overall construct type, connecting bar type, and IP and TP size combination on mechanical properties were assessed with mixed-model ANOVAs. Both FESSA constructs had significantly greater median stiffness and median torque at yield than both acrylic bar constructs; FESSA constructs with a 1.6-mm IP and 1.6-mm TPs had greatest stiffness of all tested constructs and lowest gap strain at yield. No FESSA constructs failed during testing; 7 of 12 acrylic bar constructs failed by fracture of the connecting bar at the interface with a TP. Although acrylic bar ESFs have been successfully used in avian patients, the FESSA constructs in this study were mechanically superior to acrylic bar constructs, with greatest benefit resulting from use with the larger TP configuration.

Influence of the addition of glass fibers reinforcements in the flexural strength of acrylic resin

Objective: To evaluate the influence of glass fiber reinforcements used in nautical and sports products on the flexural strength of acrylic resin. Materials and methods: Thirty thermoactivated acrylic resin bars (25 x 10.5 x 3.3 mm) were used. The samples were shared in 3 groups: bars with no glass fiber (control group, n = 10), bars reinforced with glass fiber and 0.18 mm thickness (group F1, n = 10) and bars reinforced with glass fiber and 0.80 mm thickness (group F2, n = 10). After 48 hours, samples were submitted to compression test in order to evaluate flexural strength. Obtained data were statistically analyzed with significance level of 5 %. Results: It was observed that the use of glass fiber effectively increased the flexural strength compared to the control group; the thickness of the glass fiber, however, did not present statistical differences. Conclusion: The use of fiber glass is a simple and cost-effective alternative to improve acrylic resin performance.KeywordsFlexural strength; Water sports; Dentures.

Surface roughness of acrylic denture base resins polished with different abrasive agents: an in-vitrostudy

Background: Excessive surface roughness on the denture base can adversely impact the oral health of the patient. Therefore, it is necessary to polish the denture before they are delivered to the patient. The abrasive and polishing agents should provide a smoother surface without affecting the physical and mechanical properties of denture bases. Aim: This study aims to examine and understand the potential of different polishing materials on surface roughness of acrylic denture base resins. Materials and methods: A total of 60 Heat-cure acrylic specimens (acrylic bars) were made and grouped into six groups. Control (no abrasive), Pumice (Micro-white), Eggshell powder, Seashell powder, Black sand powder, White sand powder are used as abrasive materials for polishing these specimens. These polished specimens were subjected to profilometer surface roughness analysis. Results: The acrylic specimens polished with eggshell powder on acrylic specimens showed the least surface roughness followed by black sand, white sand, pumice and seashell powders. Tukey HSD showed significant differences (p=0.000) between unpolished and polished specimens. Conclusion: Eggshell powder effectively reduced the surface roughness of denture base resin material. However, the surface roughness demonstrated by all the abrasive materials used was within the threshold limit (2 µm). Therefore, all the materials can be used as abrasives.

Reconstruction on fast neutron CT for concrete structure inspection with a pixel-type detector by applying linear scanning method

Concrete structure has been widely used in bridges and highways, however, its performance will be deteriorated after long term serving or suffering disaster. Since fast neutron has strong transmission ability and is sensitive to water content in the concrete structure, it can provide an effective probe to inspect the inner structure of concrete with non-destructive way. Thus, we propose a fast neutron imaging and reconstruction system of 3D CT for concrete structure inspection with Riken accelerator-driven compact neutron source (RANS) using a fast neutron pixel-type detector, which has 8×8 pixels. To have a good space resolution on the reconstructed image, a rotation + linear scanning method is devised and is used to collect the projection data from experiment or calculation. In this paper, reconstruction for a concrete object containing both iron bars and acrylic bars for simulation of water has been conducted. As a result, 3D image of 1cm diameter bar is reconstructed by the sparse reconstruction algorithm.

Efficacy of removing Candida albicans from orthodontic acrylic bases: an in vitro study

BackgroundThis study evaluated the efficacy of four methods in removing Candida albicans from the acrylic base material used to fabricate removable orthodontic appliances.MethodsHeat-processed bars of orthodontic acrylic were incubated in a suspension of C. albicans for 2 h at 37 °C. Samples were allocated into five groups (five bars per group) according to the cleaning method: (1) manual brushing using a toothbrush; (2) soaking in a commercial denture cleaning solution; (3) soaking in a commercial mouthwash solution; (4) using an ultrasonic cleaner; and (5) soaking in distilled water as a negative control. Yeast remaining attached to the bars after cleaning were removed by vortexing in growth medium and plated on Sabouraud dextrose agar. The reduction in yeast colony count after cleaning was calculated and expressed as the number of colony forming units per acrylic bar (CFU/bar). The experiment was carried out three times.ResultsAll four cleaning methods resulted in a significant decrease in viable yeast cells associated with the acrylic bars compared to the control group. The mean percentage reduction in viable yeast cells affected by the cleaning methods was: brushing 89.9%; chlorhexidine 95.8%; ultrasonic cleaning 99.9%; and denture tablet 100%.ConclusionsAll four methods evaluated in this study were effective, to some extent, in removing C. albicans from orthodontic acrylic samples. The most effective, and readily available, cleaning method was the use of commercial denture sterilizing tablets.

Effect of Immersion Time in 2, 5% Sargassumpolycystum Effervescent Granule Denture Cleansing Agent on the Stability

Sargassumpolycystumis one type of brown seaweed (Phaeopychae) which contains various pigment content such as beta carotene, chlorophyll a and b, and fucoxanthin. Acrylic resin has the porosity and the ability to absorb liquids that can cause discoloration. The purpose of this study was to investigate the colour stability of heat cured acrylic resin plate after immersed in Sargassumpolycystum effervescent granule. This is a laboratory experimental research with a pretest-post test with control group design. The samples are 27 pieces of 20 mm x 10 mm x 2 mm acrylic bars. Samples were divided into 9 groups containing three negative control groups mineral water, there positive control groups Sodium perborate (polident), an d three groups of Sargassumpolycystum 2, 5% filtrate groups. The immersions were performed in the room temperature for 5, 10, and 15 minutes for every control group. Discolorations of each group were measured using a colorimeter. Statistical tests for this research were independent t-test. Colour change of the acrylic resin plate after immersed in dental prosthesis cleansing agent made from effervescent granule of Sargassumpolycystum 2, 5% occurred because of the increase of microporosity on the surface of the rough plate which made pigment micromolecules more attached so that the color of acrylic plate became brown (p<0.05). Acrylic resin plate color changed after immersed in 2, 5% Sargassumpolycystum granules at 10 and 15 minutes.

Influence of aging on bond strength of artificial teeth to denture base acrylic resins

Aim: The aim of this study was to evaluate the bond strength of artificial teeth to different types of denture base resins when submitted to thermomechanical cycling (TMC). Methods: Sixty artificial mandibular first molars (Trilux, Vipi) were randomly divided into 3 groups according to denture base acrylic resins (Vipi Wave, Vipi Cril, and Vipi Cril Plus, Vipi). The teeth were fixed onto self-polymerizing acrylic resin bars (0.5 cm2 cross-section x 2 cm height), and the set was included in a metal flask using dental stone/silicone. After the dental stone was set, the bar was removed, and the denture base resin was packed and processed according to the group studied (Vipi Wave: 180 W/20 minutes + 540W/5 minutes; Vipi Cril and Vipi Cril Plus: Water bath at 74ºC for 9h). After polymerization, the samples were divided into 2 groups (n=10), according to the TMC treatment received (simulation of 5 years of mastication or not). The samples were submitted to tensile bond strength test (1 mm/min), and the data (MPa) were statistically analyzed (2-way ANOVA, Bonferroni, α=0.05). The fracture interfaces were evaluated using a stereomicroscope (50x). Results: The bond strength results showed no statistically significant difference (p&gt;0.05) between the resins studied. TMC was significant (p&lt;0.05), demonstrating lower values for the bond strength of artificial teeth to Vipi Cril Plus. The predominant fracture type was cohesive in resin. Conclusions: It was concluded that there is no difference in bond strength between artificial teeth and the resins used for denture base. However, TMC decreases the bond strength values of artificial teeth and crosslink thermo-polymerizable acrylic resin.

Influence of ethanol on dentin roughness, surface free energy, and interaction between AH Plus and root dentin.

This study aimed to evaluate the influence of different ethanol concentrations on dentin roughness, surface free energy, and contact angle between AH Plus and the root canal dentin. One hundred human maxillary anterior teeth were split longitudinally and 200 dentin specimens were polished to make the surface flatter and smoother. An acrylic bar was positioned between two dentin specimens and impression material was added to create a block, simulating an instrumented root canal space. Specimens were removed from the mold and cleaned in an ultrasonic bath for 10 min. Thereafter, dentin specimens were divided into four groups (n = 50) according to the drying methods used: a) wet: vacuum only, b) paper points: vacuum + absorbent paper points, c) 70% alcohol: 70% alcohol (1 min) + vacuum + absorbent paper points, and d) 100% alcohol: 100% alcohol (1 min) + vacuum + absorbent paper points. A rugosimeter and a goniometer were used to verify the roughness (Ra) and to measure the surface free energy and the contact angle between the AH Plus sealer and the root canal dentin. ANOVA and Tukey tests (α = 0.05) were used for statistical analysis. The 70% and 100% ethanol groups showed significantly decreased roughness as well as increased surface free energy in the root canal dentin when compared to the wet and paper point groups. In addition, ethanol significantly reduced the contact angle between the AH Plus sealer and the root canal dentin. Ethanol solutions (70% and 100%) provide better wettability of AH Plus sealer on dentin surfaces.

Chitosan 2% Effect on Prohibiting the Growth of Candida Albicans on Heatcured Acrylic Resin

Maintaining acrylic denture hygiene is a necessary to prohibit the growth of several oral fungi such as Candida albicans. Candida albicans are the main etiological microorganism of denture stomatitis. One of the ways to clean denture is by immersion on synthetic denture cleaner liquid such as oxygenizing denture cleaners. However, synthetic denture cleaner have several limitation due to its biocompatibility on human body especially oral tissue. Chitosan is a derivate of chitin, a natural compound of sea creature exosceleton. Chitosan have antifungi and antibacterial nature. The objective of this study is to evaluate the antifungi efectifity of chitosan 2% on acrylic heatcured and compare it with oxygenizing denture cleaner. Aquades is used as a control. The sample consists of 15 acrylic heatcured bars (10x10x2 mm) prepared by contamination on Candida albicans suspensions at temperature 37°C for 24 hours and immersed on 3 different treatments wich are chitosan 2%, oxygenizing denture cleanser, and aquades as control and then, the solutions are being vibrate and put into sabouraud dextrose agar medium. The colony of Candida albicans counted manually. Result shows, highest mean of Candida albicans colony on aquades group (365,66 CFU/plate), followed by oxygenizing denture cleanser treatment (178,33 CFU/plate). The smallest number colony of Candida albicans are found at chitosan 2% treatment (45,33 CFU/plate). Statistical analysis using ANOVA one way shows F=9.826 and p=0, this means, there is minimal one pair of groups with very significant differential (p&lt;0,01) which are chitosan 2% and oxygenizing denture cleanser compared to aquades as control. The difference between those two treatments also significant. Conclusions of this study is that chitosan 2% solution have a sifnificant effect on prohibiting the growth of Candida albicans colony on acrylic heatcured denture base materials. The effectivity of this solution is significantly higher than oxygenizing denture cleanser treatment.

Characterization of system-related geometric distortions in MR images employed in Gamma Knife radiosurgery applications

This work provides characterization of system-related geometric distortions present in MRIs used in Gamma Knife (GK) stereotactic radiosurgery (SRS) treatment planning.A custom-made phantom, compatible with the Leksell stereotactic frame model G and encompassing 947 control points (CPs), was utilized. MR images were obtained with and without the frame, thus allowing discrimination of frame-induced distortions. In the absence of the frame and following compensation for field inhomogeneities, measured average CP disposition owing to gradient nonlinearities was 0.53 mm. In presence of the frame, contrarily, detected distortion was greatly increased (up to about 5 mm) in the vicinity of the frame base due to eddy currents induced in the closed loop of its aluminum material. Frame-related distortion was obliterated at approximately 90 mm from the frame base. Although the region with the maximum observed distortion may not lie within the GK treatable volume, the presence of the frame results in distortion of the order of 1.5 mm at a 7 cm distance from the center of the Leksell space. Additionally, severe distortions observed outside the treatable volume could possibly impinge on the delivery accuracy mainly by adversely affecting the registration process (e.g. the position of the lower part of the N-shaped fiducials used to define the stereotactic space may be miss-registered). Images acquired with a modified version of the frame developed by replacing its front side with an acrylic bar, thus interrupting the closed aluminum loop and reducing the induced eddy currents, were shown to benefit from relatively reduced distortion.System-related distortion was also identified in patient MR images. Using corresponding CT angiography images as a reference, an offset of 1.1 mm was detected for two vessels lying in close proximity to the frame base, while excellent spatial agreement was observed for a vessel far apart from the frame base.

Development of phantom for quantitative analyses of human dentin mineral density.

The purpose of the present study was to develop a novel-designed phantom that could be scanned with a sample in the same image, that specialize for quantitative analyses of human dentin mineral density using the X-ray attenuation method. A further attempt was made to demonstrate the intracoronal dentin mineral density using this phantom in mandibular incisors. The phantom prepared with a 15 mm hole in the center of an acrylic resin bar having an outside diameter of 25 mm and 8 small holes (diameter, 3 mm) were made at equal intervals around the center. Liquid dipotassium hydrogen phosphate (K2HPO4) solutions were established at 0.4, 0.6, 0.8 and 1.0 g/cm3, and were arranged to these holes. The mean value of the intracoronal dentin mineral density was 1.486 ± 0.016 g/cm3 in the present study. As the results of the present study corresponded to previous reports, this new phantom was considered to be useful. This phantom enables the analysis of samples that are not readily available by conventional mechanical tests and may facilitate biomechanical investigations using X-ray images. It was suggested that this system is a simple, accurate and novel mineralization measuring system.

Evaluation of different support materials used with a photo-fermentative consortium for hydrogen production

Three different support materials were evaluated for immobilization of a consortium of purple non-sulfur bacteria producing hydrogen gas. The inoculum was obtained from a bioelectrochemical system, and it was subsequently enriched. Molecular analysis showed that the consortium was mainly composed of Rhodopseudomonas palustris. The tested materials included acrylic rods, high-density polyethylene cylinders and luffa (dispersed fibers and cubes). The hydrogen production, using volatile fatty acids as the substrate, was evaluated in continuously illuminated reactors (7 klux) at 32 °C. The hydrogen production rate observed was between 14 and 20 mL H2/g VS/h. Dispersed luffa fibers showed the highest amount of immobilized biomass (19.6 ± 1.5 mg VS/cm3) followed by luffa in cubes, high-density polyethylene cylinders, and acrylic bars. The dispersed luffa fibers allowed for a better light distribution and contact with the media than the luffa in cubes. There was no significant difference in hydrogen production among the three support materials (luffa, acrylic bars or polyethylene) when the same amount of immobilized biomass was used. The luffa in fibers was the most suitable support for the purple non-sulfur consortium because of the highest area/volume ratio, biomass attachment as well as the adequate light distribution.

Improved TPB-coated light guides for liquid argon TPC light detection systems

Scintillation light produced in liquid argon (LAr) must be shifted from 128 nm to visible wavelengths in light detection systems used for liquid argon time-projection chambers (LArTPCs). To date, LArTPC light collection systems have employed tetraphenyl butadiene (TPB) coatings on photomultiplier tubes (PMTs) or plates placed in front of the PMTs. Recently, a new approach using TPB-coated light guides was proposed. In this paper, we report on light guides with improved attenuation lengths above 100 cm when measured in air. This is an important step in the development of meter-scale light guides for future LArTPCs. Improvements come from using a new acrylic-based coating, diamond-polished cast UV transmitting acrylic bars, and a hand-dipping technique to coat the bars. We discuss a model for connecting bar response in air to response in liquid argon and compare this to data taken in liquid argon. The good agreement between the prediction of the model and the measured response in liquid argon demonstrates that characterization in air is sufficient for quality control of bar production. This model can be used in simulations of light guides for future experiments.

The influence of polymerization type and reinforcement method on flexural strength of acrylic resin.

The aim of this study was to evaluate the flexural strength of acrylic resin bars by varying the types of resin polymerization and reinforcement methods. Fourteen groups (N = 10) were created by the interaction of factors in study: type of resin (self-cured (SC) or heat-cured (HC)) and reinforcement method (industrialized glass fiber (Ind), unidirectional glass fiber (Uni), short glass fiber (Short), unidirectional and short glass fiber (Uni-Short), thermoplastic resin fiber (Tpl), and steel wire (SW)). Reinforced bars (25 × 2 × 2 mm) were tested in flexural strength (0.5 mm/min) and examined by scanning electron microscopy (SEM). Data (MPa) were submitted to factorial analysis, ANOVA, and Tukey and T-student tests (a = 5%) showing significant interaction (P = 0.008), for SC: Uni (241.71 ± 67.77)a, Uni-Short (221.05 ± 71.97)a, Ind (215.21 ± 46.59)ab, SW (190.51 ± 31.49)abc, Short (156.31 ± 28.76)bcd, Tpl (132.51 ± 20.21)cd, Control SC (101.47 ± 19.79)d and for HC: Ind (268.93 ± 105.65)a, Uni (215.14 ± 67.60)ab, Short (198.44 ± 95.27)abc, Uni-Short (189.56 ± 92.27)abc, Tpl (161.32 ± 62.51)cd, SW (106.69 ± 28.70)cd, and Control HC (93.39 ± 39.61)d. SEM analysis showed better fiber-resin interaction for HC. Nonimpregnated fibers, irrespective of their length, tend to improve fracture strength of acrylics.

Design on illumination of structures for lighthouse in Korea

This paper presents information about the examples of the design on Illumination of Structures(LED Light Pipe for lighthouse) in Korea. We have applied illumination by flood-lighting or facade-lighting in place of the 57 lighthouses (offshore structures) and 4 beacons. The ways of illumination of structures are using direct illumination with LED, halogen lamps and metal halide lamps, and indirect illumination with LED non-neon lamps. The illumination of structures helps a observer to identify the Aids to Navigation and waterway. The fabricated LED Light Pipe is a transparent acrylic round bar and easy to install. The Light Pipe is arranged in two rows of LED (78ea). It can be connected in series. It has 4 colours(Red, Green, Yellow, White). We analyzed and the horizontal divergence angle of the LED light pipe is defined as the range with 50% of maximum luminous intensity. Also, we evaluated the conspicuity on the original lantern and LED Light pipe for lighthouse. The field experiment was conducted in ‘Yeosuguhang lighthouse’ in Yeosu-city (Korea). From the experimental results, it was confirmed that the fabricated LED Light Pipe is clearly distinguished.

High sensitivity non-contact method for dynamic quantification of elastic waves and strains in transparent media

This paper presents time resolved quantitative evaluation of elastic stress waves in solid media by utilising an adaptation of the well-established laser Doppler vibrometry method. We show that the introduction of elastic stress waves in a transparent medium gives rise to detectable and quantifiable changes in the refractive index, which is proportional to stress. The method is tested for mechanical excitation at frequencies from 10 to 25kHz in an acrylic bar. This refractometric quantification can measure internal strains as low as 1×10−11. Additionally, finite element analysis is conducted to gauge the validity of the results. In the presented work an acrylic bar is used, this method however should be applicable to any transparent solid.