Acoustic Properties Research Articles

Acoustic and thermal properties of mycelium-based insulation materials produced from desilicated wheat straw - Part B

The acoustic and thermal properties were determined for biodegradable insulation materials produced from desilicated wheat straws with two different fungi and three different incubation periods. Ganoderma lucidum (GL) and Pleurotus ostreatus (PO) fungi and wheat straw were exposed to fungal incubation for 10, 20, and 30 days to produce mycelium-based insulation materials. The sound absorption coefficients of mycelium-based insulation boards produced using PO fungus were higher than those produced with GL fungus. It was found that the acoustic absorption coefficients of insulation boards produced using PO fungus at 1,000 Hz were 87 to 99% according to the incubation periods. The sound transmission losses of mycelium-based insulation boards produced ranged from 46.4 to 59.7 dBa at 1000 Hz. The group of boards labeled as YP2 exhibited the lowest level of sound transmission loss, whereas GL2 revealed the highest degree of sound transmission loss at 1000 Hz. The lowest thermal conductivity coefficient was obtained in insulation boards produced with PO fungus and an incubation period of 20 days. The limiting oxygen index (LOI) value of mycelium-based insulation materials was considerably higher than the insulation boards commonly used today. Thermogravimetric analysis and derivative thermogravimetry curves of mycelium-based insulation materials were also determined.

High-accuracy high temperature measurement based on forward Brillouin scattering of polyimide-coated optical fiber

In this paper, a novel method for high-accuracy high temperature measurement is proposed, which is based on forward Brillouin scattering (FBS) of double-coated optical fiber with polyimide outer coating. The temperature variation changes the acoustic properties of polyimide-coated fiber that is suitable for high temperature measurement in the range of 120 ∼ 220 ℃. An interesting feature is that different radial acoustic modes have different frequency responses in the polyimide-coated fiber. Another interesting phenomenon is that the temperature linearly depends on the frequency shift of FBS spectrum with high sensitivity from 120 ℃ to 220 ℃. By using one acoustic mode with a high frequency shift-temperature sensitivity, we propose a novel high temperature measurement method based on FBS with high measurement accuracy. The experimental result shows that the low temperature measurement uncertainty of 0.02 ℃ can be achieved. The proposed method is expected to be used for high-accuracy temperature measurement applications within a temperature range of 100 ∼ 200 ℃, such as underground oil layer detection, power plant monitoring and high-power electrical systems monitoring.

Listening to trees in the forest: Attentional set influences how semantic and acoustic factors interact in auditory perception.

Studies of auditory object perception claim that semantic properties dominate acoustic properties in determining identification accuracy. Yet the direction of the semantic effect is mixed, with some studies showing an advantage for detecting incongruent sounds and others reporting a congruent sound advantage. Here we examine the role of the participant's attentional set when identifying auditory objects in naturalistic soundscapes. We varied the acoustic and semantic properties of the sounds orthogonally in two experiments. In Experiment 1 participants tuned their attention broadly to detect any change between two successive soundscapes (e.g., two restaurant soundscapes, with and without a child coughing). In Experiment 2 they tuned attention more narrowly to a probe presented after a soundscape (e.g., a restaurant soundscape with a child coughing, followed by the coughing sound alone). In both experiments, semantic relations between the objects and backgrounds helped to disambiguate objects that blended acoustically with the background. When attending globally (Experiment 1), objects that were acoustically similar yet semantically incongruent tended to be missed (e.g., bouncing basketball on a construction site), as though camouflaged by the gist of the soundscape. When attending locally (Experiment 2), semantically congruent foil objects led to false positive reports under acoustically similar conditions (hammering sounds on a construction site), as though the gist of the soundscape contributed to their plausible inclusion. In summary, although attentional set had a strong influence on the specific kinds of errors made, both results pointed to participants using a semantically congruent high-level schema to report the sounds they heard.

Compensation of composition variation-induced sensitivity changes in gas phase photoacoustics

Infrared photoacoustic (PA) spectroscopy is a widely used technique to monitor trace gas concentration changes during industrial processes where the bulk composition may vary considerably. However, the PA signal is prone to changes in bulk composition, leading to relative uncertainties in measurements of up to 10%, due to the complex dependence of the sensitivity of a PA system (S) on the thermal and acoustic properties of the gas sample. A novel calibration and concentration calculation method is proposed to keep the relative accuracy of the PA measurements in the few percentages range even in case of large-scale composition variations. The main novelty of the proposed method is that it tackles the complex dependence of the PA system's sensitivity in a way that while it varies the resonance frequency of the calibration gas, it keeps the heat capacity ratio of calibration gases at a constant value. We prove that it determines the analyte’s concentration with relative accuracy of about 1 %, even when the composition of the gas varies drastically. It rigorously compensates for the frequency and heat capacity ratio dependence of S and for the dependence of the half-width of the resonance curve of the PA cell on the thermal and acoustic properties of the gas. Although the reported demonstration measurements are executed in a relatively simple gas mixture, the proposed method has widespread applicability in high-precision monitoring.

UIO-66-NH2/polydopamine double coating modification on cotton fabric for sound absorption and noise reduction

Noise pollution greatly harms social and economic development and human health. Textiles are used frequently and are essential to the interior's sound absorption and noise reduction. In this study, a polydopamine layer with damping, noise reduction, and adhesion functions was first finished onto cotton fabrics using a deposition method, followed by uniform spraying of Metal-organic framework particles with porous sound absorption structures using an ultrasonic precision sprayer. The successful adhesion of dopamine and UIO-66-NH2 on the fiber surface was verified using characterization methods, and the parameters affecting the acoustic properties of the fabric were explored. The results show that MOFs and polydopamine improve fabrics' absorption and reduction of acoustic waves. This work confirms the successful application of the double coating of UIO-66-NH2 and dopamine in fabric sound absorption. It provides a method for designing and preparing acoustic protection textiles.

Aircraft noise modifies acoustic signals and social interactions of a microendemic frog from Mexico City

Research on urban noises affecting acoustic communication of animals is a growing area of study and conservation concern. However, the consequences of aircraft noise on anuran acoustic communication have been explored on a restricted basis to date. In this study, we investigated the impact of aircraft overflights on the individual and chorus performance of acoustic signalling in the Pedregal frog (Eleutherodactylus grandis), a microendemic and threatened species from Mexico City. During the summer of 2021, we recorded acoustic signals from male individuals and conducted acoustic monitoring to analyse how chorus social interactions change due to aircraft overflights. For this purpose, we evaluated acoustic properties of the call, including call duration, dominant frequency, call amplitude, and call repetition rate. Additionally, we measured the amplitude of environmental noises and signals by means of two types of complementary methodological approaches. Our results show changes in the individual performance of acoustic signals with longer call duration, lower dominant frequency, and higher call amplitude due to aircraft overflights, while individual call repetition rate did not vary. Furthermore, a decrease in the number of calls within the chorus was observed during aircraft overflight. Overall, these results show that aircraft noise causes plastic changes in the acoustic signals of the Pedregal frog and that social interactions between conspecifics decrease, thus adding a new disturbance to this species that already suffers from other anthropogenic noises, and habitat fragmentation.

Effect of water absorption, hardness, and acoustic properties on sandwich syntactic foam composite for structural and marine applications

AbstractIn this study, a sandwich composite structure was fabricated with core syntactic foam composites (SFC) reinforced with face-sheets of combined kenaf and glass fibers. The core SFC was made from hollow glass microsphere (HGM)/epoxy resin mixture. The focus of this study is to design a suitable material for marine, automobile, and structural applications by investigating the water absorption capacity, hardness, buoyancy, and acoustic resistance level of the sandwich composite. Four sequences of face-sheet reinforcement [e.g. kenaf-kenaf(KK); glass-glass(GG); glass-kenaf(GK), and kenaf-glass(KG)] were adopted. The results show that the KK sandwich absorbed more water, with buoyancy level of 0.329% than other sequence. GK shows the highest sandwich in hardness strength with 58Hv, and 35% more than the KK, while there was no significant difference in the sound pressure level of the sandwich composite.

Planar piezoelectric metamaterials: Sound transmission and applicable frequency range in oblique incidence

Frequency limit and applicable frequency range of planar piezoelectric metamaterials connected to external circuits have not been well defined in estimating the sound transmission loss. This article extends the classical transfer matrix method for use in evaluating the sound transmission of thin-plate piezoelectric metamaterials in oblique incidence. Using the Kirchhoff thin plate theory, a modified transfer matrix method that takes factors of external circuits into consideration is developed for attenuation and control of acoustic waves. Several vibro-acoustic analytical models are compared, including the Kirchhoff thin plate theory, the Reissner–Mindlin thick plate theory and the theory of wave propagation in elastic solids. These theories are used to determine the dispersion relation, coincidence and transition frequency of thin and thick plate theories in analysing piezoelectric acoustic metamaterials, alongside a validation using the finite element method. Then acoustic properties of piezoelectric plates connected to passive external circuits are studied parametrically with both dimensional and dimensionless variables based on an equivalent Kirchhoff plate approximation. The findings show that external electrical impedance alone can be used to adjust the resonance frequency over a broad range and thereby control sound transmission loss. This provides considerable flexibility in modifying the acoustic properties of the piezoelectric metamaterial in comparison to traditional, fixed-structure metamaterials. The study indicates a straightforward and powerful analytical approach for the optimization of acoustic insulation using thin-plate piezoelectric metamaterials.

Influence of thermophysical and acoustic properties on temperature elevation at muscle/bone interface induced by ultrasound hyperthermia

Therapeutic ultrasound heating is a very common technique in the treatment of muscular and joints injuries. However, insufficient or excessive heating delivered to living tissues can be either innocuous or hazardous to the patient. The present work deals with the heat transfer process in living tissues, with particular concern on the behavior at the muscle-bone interface, when ultrasound irradiation is applied. Based on the Generalized Integral Transform Technique (GITT), a hybrid numerical-analytical solution of the Pennes’ equation using the open-source UNIT code (“UNified Integral Transforms”) is proposed, considering different boundary conditions. The influence of physical properties and parameters, such as beam incidence angle, acoustic attenuation coefficients for refracted longitudinal and shear waves in the bone, and blood perfusion in the muscle, were more closely analyzed. Numerical results of temperature profiles showing variations of up to 2 °C for different situations are presented, illustrating a marked dependence of heating patterns on the perfusion rates as well as on the effect of shear waves. The conclusions are that such type of more detailed analysis is essential for the accurate identification of physical properties in living tissues and phantoms and can contribute to the treatment planning for therapeutic ultrasound.

Microstructure-based modeling to characterize low pore density open-cell foams and its experimental validation.

Microlattices with large pore sizes are involved in many multifunctional applications, so it is essential to understand their acoustic properties. However, for these low pore density microlattice foams, the classical homogenization or "equivalent fluid" methods fail abruptly. This paper proposes and discusses a microstructure-based direct fluid model (DFM) that would help to predict the acoustic performance of low pore density periodic open-cell foams with spherical pores. The DFM is simulated directly, including the microscale geometric features inherent in the unit cell. A comparative study is performed for designed three-dimensional (3D) body-centered-cubic (BCC) porous foams having pores per inch (PPI) ranging from 1 to 12 over the frequency range of 500-4100 Hz with equivalent fluid models and experiments. The study shows the extent of deviation in homogenization-based methods from the experiment for PPI < 5. On the other hand, the acoustic performance parameters predicted with the DFM agree well with experiments on 3D-printed samples fabricated by additive manufacturing of varying PPI starting from 1. This study shows that the DFM is a valid method to predict the acoustics of low PPI microlattices. Furthermore, the gradual transition from dissipative to the reactive regime with a decrease in PPI is also brought out.

Evaluation of acoustic-thermal simulations of invivo magnetic resonance guided focused ultrasound ablative therapy.

To evaluate numerical simulations of focused ultrasound (FUS) with a rabbit model, comparing simulated heating characteristics with magnetic resonance temperature imaging (MRTI) data collected during invivo treatment. A rabbit model was treated with FUS sonications in the biceps femoris with 3D MRTI collected. Acoustic and thermal properties of the rabbit muscle were determined experimentally. Numerical models of the rabbits were created, and tissue-type-specific properties were assigned. FUS simulations were performed using both the hybrid angular spectrum (HAS) method and k-Wave. Simulated power deposition patterns were converted to temperature maps using a Pennes' bioheat equation-based thermal solver. Agreement of pressure between the simulation techniques and temperature between the simulation and experimental heating was evaluated. Contributions of scattering and absorption attenuation were considered. Simulated peak pressures derived using the HAS method exceeded the simulated peak pressures from k-Wave by 1.6 ± 2.7%. The location and FWHM of the peak pressure calculated from HAS and k-Wave showed good agreement. When muscle acoustic absorption value in the simulations was adjusted to approximately 54% of the measured attenuation, the average root-mean-squared error between simulated and experimental spatial-average temperature profiles was 0.046 ± 0.019 °C/W. Mean distance between simulated and experimental COTMs was 3.25 ± 1.37 mm. Transverse FWHMs of simulated sonications were smaller than in invivo sonications. Longitudinal FWHMs were similar. Presented results demonstrate agreement between HAS and k-Wave simulations and that FUS simulations can accurately predict focal position and heating for invivo applications in soft tissue.

Vibration Characteristics of Liquid-Filled Pipes Under Different Levels of Submergence

Based on the acousto-solid coupling theory, the vibroacoustic radiation characteristics of the liquid-filled pipeline are studied under different submergence depths, and the changes of sound pressure level of pipeline are analyzed under different submergence depths of the flow transfer pipeline. The vibration characteristics of liquid-filled pipes with different submergence degrees were numerically analyzed from the pressure-acoustic domain and the solid mechanics domain, and the two-way coupled data exchange was realized by using acoustic-structural boundary multi-physical field function. The sound pressure level variation curves of the liquid-filled pipes were calculated for different submergence depths under the simultaneous action of internal and external flow fields, respectively. The results show that when the pipe is submerged in the lower and middle positions of the center of the circle, the sound pressure fluctuations of the pipe radiating outward are more consistent, and when submerged in the upper half, the sound pressure concentration phenomenon occurs in the lower and middle regions outside the pipe. When the free boundary outside the pipe is subjected to the boundary load, the pipe submerged in the lower position of the center of the circle is most obviously affected by the load. The tube submerged in the upper and lower positions of the center of the tube will produce two-way, increasing the form of sound pressure propagation in the tube towards the upper and lower sides, these findings can provide a certain reference for the study of pipe vibroacoustics. Therefore, research on the acoustic radiation properties of liquid-filled pipelines under various submergence depths is of great theoretical significance and engineering application value. This information can be applied widely in the fields of anti-fatigue design, fatigue damage analysis, and safety assessment of oil and gas pipeline structures, providing strong scientific support to ensure their safe and reliable service.

Theoretical study on resonance frequencies of vibration modes of Janus-Helmholtz transducer

Janus-Helmholtz transducer has the characteristics of high-power and broadband transmission due to the coupling between the longitudinal resonance of the driver and the liquid cavity resonance of Helmholtz resonator. Traditional view holds that the low frequency resonance peak in the transmitting voltage response curve in water is fluid cavity mode of Helmholtz resonator while the high frequency resonance is the longitudinal mode of Janus transducer. However, in the past few decades, a large number of experimental studies have found that this conclusion is questionable. This work is to distinguish the two resonances in the response curve and the two vibration modes of Janus-Helmholtz transducer. Based on the Janus-Helmholtz transducer prototype reported in the literature, the resonance frequencies of the vibration modes of Janus-Helmholtz transducer are studied theoretically. The structure dimensions and material parameters of the prototype are listed in detail. The test results and simulation results of conductivity are also presented. The longitudinal resonance of the driver is determined by using the equivalent circuit method and finite element analysis. Radiation masses of both Janus transducer and typical longitudinal vibration transducer are also calculated to analyze the phenomenon of the sharp decrease of longitudinal resonance frequency in water. Acoustic modal analysis by using ANSYS software is performed to investigate the resonance frequency of complex Helmholtz resonator in Janus-Helmholtz transducer. Correction length on the vent introduced by external fluid sound radiation is used to obtain the accurate Helmholtz resonance frequency. The sound pressure distribution of Helmholtz resonator obtained through finite element method is investigated, and the correct equivalent formula for solving the Helmholtz resonance frequency is obtained. The results reveal that the first resonance in the response curve is driver resonance while the second one is Helmholtz resonance, which is contrary to the traditional view. The considerable reduction of driver resonance frequency in water is mainly due to the large radiation mass on the four large radiation surfaces of the Janus transducer, which also causes the sharp response of driver resonance. In Janus-Helmholtz transducer, there are two Helmholtz resonators with the same size, instead of only one resonator in the traditional view. The two resonance frequencies solved by the method proposed in this work are in good agreement with the test and simulation results. These conclusions play an important role in correctly understanding the structure and characteristics of Janus-Helmholtz transducer at source, as well as provide technical support for structural optimization and innovation, thus improving the acoustic emission properties of the transducer.

Historical evolution and acoustic significance of sound holes in lutes

This study presents a comprehensive investigation into the impact of sound hole configurations on the acoustic properties of short-necked lute instruments. The primary objective of this analysis is to enhance our understanding of how the size and placement of sound holes influence the soundboard of the lute. A morphological examination traces the historical and cross-cultural significance of sound hole designs, shedding light on their evolution from antiquity to modern times. Experimental tests systematically compare the acoustic characteristics and potential applications of two prevalent sound hole arrangements: single-hole and triple-hole configurations. The results demonstrate that the triple-hole configuration exhibits a significantly higher amplitude profile, indicating enhanced average energy, perceived loudness, and sustained resonance. This pronounced dynamic range proves advantageous in scenarios requiring a wide amplitude range, such as musical performances or audio recordings with varying intensity levels.

Real-Time Speed-of-Sound Estimation in Vivo via Steered Plane Wave Ultrasound.

Speed-of-sound (SoS) is an intrinsic acoustic property of human tissues and has been regarded as a potential biomarker of tissue health. To foster the clinical use of this emerging biomarker in medical diagnostics, it is important for SoS estimates to be derived and displayed in real-time. Here, we demonstrate that concurrent global SoS estimation and B-mode imaging can be achieved live on a portable ultrasound scanner. Our innovation is hinged upon the design of a novel pulse-echo SoS estimation framework that is based on steered plane wave imaging. It has accounted for the effects of refraction and imaging depth when the medium SoS differs from the nominal value of 1540 m/s that is conventionally used in medical imaging. The accuracy of our SoS estimation framework was comparatively analyzed with through-transmit time-of-flight measurements in vitro on 15 custom agar phantoms with different SoS values (1508 to 1682 m/s) and in vivo on human calf muscles (N = 9; SoS range: 1560 to 1586 m/s). Our SoS estimation framework has a mean signed difference of, respectively, -0.6±2.3 m/s in vitro and -2.2±11.2 m/s in vivo relative to the reference measurements. Additionally, our real-time system prototype has yielded simultaneous SoS estimates and B-mode imaging at an average frame rate of 18.1 fps. Overall, by realizing real-time tissue SoS estimation with B-mode imaging, our innovation can foster the use of tissue SoS as a biomarker in medical ultrasound diagnostics.

End-to-End Bayesian Segmentation and Similarity Assessment of Performed Music Tempo and Dynamics without Score Information

Segmenting continuous sensory input into coherent segments and subsegments is an important part of perception. Music is no exception. By shaping the acoustic properties of music during performance, musicians can strongly influence the perceived segmentation. Two main techniques musicians employ are the modulation of tempo and dynamics. Such variations carry important information for segmentation and lend themselves well to numerical analysis methods. In this article, based on tempo or loudness modulations alone, we propose a novel end-to-end Bayesian framework using dynamic programming to retrieve a musician's expressed segmentation. The method computes the credence of all possible segmentations of the recorded performance. The output is summarized in two forms: as a beat-by-beat profile revealing the posterior credence of plausible boundaries, and as expanded credence segment maps, a novel representation that converts readily to a segmentation lattice but retains information about the posterior uncertainty on the exact position of segments’ endpoints. To compare any two segmentation profiles, we introduce a method based on unbalanced optimal transport. Experimental results on the MazurkaBL dataset show that despite the drastic dimension reduction from the input data, the segmentation recovery is sufficient for deriving musical insights from comparative examination of recorded performances. This Bayesian segmentation method thus offers an alternative to binary boundary detection and finds multiple hypotheses fitting information from recorded music performances.

Research of Insertion Loss of Multilayered Construction with Devulcanized Waste Rubber

Abstract In this study, the insertion loss of devulcanized waste rubber baffles were evaluated. Acoustic baffles are suitable to reduce noise from the devices or machines by interfering with their emitting sound waves. Knowledge of the acoustic properties of the material used is of significant importance in ensuring the effectiveness of the acoustic properties of the baffle. Basic properties include airborne sound insulation, which is usually determined during laboratory tests. Baffles consists of sound absorbing and sound insulating materials. In this study, plasterboards were used as sound insulating material and devulcanized waste rubber as sound absorbing material. During the devulcanization process, porous granules are obtained, which can be used as an acoustic material. In this study, two types of rubber granules were devulcanized by grinding method and one other type was chemically devulcanized. Three types of rubber granules were mixed together in increasing 25 % proportion steps and glued with patented polyurethane glue. A total of 15 different composition devulcanized waste rubber granule boards were made. Rubber boards were attached together with the plasterboards. Insertion loss of the different composite baffles was measured in semi-anechoic chamber in a purposefully designed stand in 1/3rd octave bands. The results showed that the insertion loss of the baffles was mostly dependent on the rubber granule board density. When the density of the rubber board increased, the insertion loss also increased. The 5–6 dB insertion loss difference was measured between the most and least dense rubber granule board baffles.

Effects of background noise on autonomic arousal (skin conductance level).

This study was designed to investigate the relationship between sound level and autonomic arousal using acoustic signals similar in level and acoustic properties to common sounds in the built environment. Thirty-three young adults were exposed to background sound modeled on ventilation equipment noise presented at levels ranging from 35 to 75 dBA sound pressure level (SPL) in 2 min blocks while they sat and read quietly. Autonomic arousal was measured in terms of skin conductance level. Results suggest that there is a direct relationship between sound level and arousal, even at these realistic levels. However, the effect of habituation appears to be more important overall.

The Acoustic Properties of Affective Timbres: Consistencies and Discrepancies in a Synthesis of Multiple Datasets

In the investigation of musical features that influence musical affect, timbre has received relatively little attention. Investigating affective timbres as they vary between instrument families can lead to inconsistent results, because one instrument family can produce a wide variety of timbres. Here, we consider timbre descriptors, as fine-grained acoustic representations of a sound. Using identical methods, we re-analyzed and synthesized results from three previously published studies: Eerola et al. (2012, Mus. Percept.), McAdams et al. (2017, Front. Psychol.), and Korsmit et al. (2023, Front. Psychol.). In doing so, we aimed to reveal robust timbre descriptors that consistently predict the affective response and to explain any discrepancies in results arising from differences in experimental methodology. We computed spectral, temporal, and spectro-temporal descriptors from all stimuli and used these to predict the affect ratings using linear and nonlinear methods. Our most consistent finding was that the fundamental frequency or higher-frequency energy of a sound predicted pleasant affect (i.e., positive valence, happiness, sadness) in one direction and unpleasant affect (i.e., tension, anger, fear) in the opposite direction. Clear discrepancies in previous findings may be attributable to differences in experimental design. When pitch variation was present in a stimulus set, energy arousal was predicted by pitch and inharmonicity, whereas when attack variation was present in the stimulus set, energy arousal was predicted by a faster attack and shorter sustain.

Head-to-Head Comparison of Acoustic Properties of Lead-Free and PZT-Based HIFU Transducers Operating at 12 MHz.

A direct comparison of performance and acoustic properties of high-intensity focused ultrasonic transducers utilizing lead-free (sodium bismuth titanate-NBT) and lead-based (lead zirconate titanate-PZT) piezoceramics is discussed. All transducers operate at 12 MHz at third harmonic frequency, having an outer diameter of 20 mm, a central hole of 5 mm in diameter, and a radius of curvature of 15 mm. The electroacoustic efficiency determined by a radiation force balance is evaluated in a range of input power levels up to 15 W. Schlieren tomography as well as hydrophone measurements are used for evaluation of the acoustic field distribution. It is found that the average electroacoustic efficiency of NBT-based transducers is approximately 40%, while it is around 80% in the PZT-based devices. NBT devices show significantly higher inhomogeneity of the acoustic field under schlieren tomography compared to PZT devices. From pressure measurements in the prefocal plane, it was found that the inhomogeneity could be attributed to depoling of significant areas of the NBT piezo-component during the fabrication process. In conclusion, PZT-based devices performed significantly better than those using lead-free material. However, the NBT devices show promise for this application and their electroacoustic efficiency as well as the uniformity of the acoustic field could be improved by employing a low-temperature fabrication process or repoling after processing.