Acoustic Path Research Articles

Large-field-of-view optical-resolution optoacoustic microscopy using a stationary silicon-photonics acoustic detector.

Optical-resolution optoacoustic microscopy (OR-OAM) enables label-free imaging of the microvasculature by using optical pulse excitation and acoustic detection, commonly performed by a focused optical beam and an ultrasound transducer. One of the main challenges of OR-OAM is the need to combine the excitation and detection in a coaxial configuration, often leading to a bulky setup that requires physically scanning the ultrasound transducer to achieve a large field of view. The aim of this work is to develop an OR-OAM configuration that does not require physically scanning the ultrasound transducer or the acoustic beam path. Our OR-OAM system is based on a non-coaxial configuration in which the detection is performed by a silicon-photonics acoustic detector (SPADE) with a semi-isotropic sensitivity. The system is demonstrated in both epi- and trans-illumination configurations, where in both configurations SPADE remains stationary during the imaging procedure and only the optical excitation beam is scanned. The system is showcased for imaging resolution targets and for the in vivo visualization of the microvasculature in a mouse ear. Optoacoustic imaging with focal spots down to , lateral resolution of , and a field of view higher than 4mm in both lateral dimensions were demonstrated. We showcase a new OR-OAM design, compatible with epi-illumination configuration. This setup enables relatively large fields of view without scanning the acoustic detector or acoustic beam path. Furthermore, it offers the potential for high-speed imaging within compact, miniature probe and could potentially facilitate the clinical translation of OR-OAM technology.

An Improved Rock Damage Characterization Method Based on the Shortest Travel Time Optimization with Active Acoustic Testing

Real-time evaluation of the damage location and level of rock mass is essential for preventing underground engineering disasters. However, the heterogeneity of rock mass, which results from the presence of layered rock media, faults, and pores, makes it difficult to characterize the damage evolution accurately in real time. To address this issue, an improved method for rock damage characterization is proposed. This method optimizes the solution of the global shortest acoustic wave propagation path in the medium and verifies it with layered and defective media models. Based on this, the relationship between the inversion results of the wave velocity field and the distribution of rock damage is established, thereby achieving quantitative characterization of rock damage distribution and degree. Thus, the improved method is more suitable for heterogeneous rock media. Finally, the proposed method was used to characterize the damage distribution evolution process of rock media during uniaxial compression experiments. The obtained results were compared and analyzed with digital speckle patterns, and the influencing factors during the use of the proposed method are discussed.

In Search of the “Phonograph Effect”: Sonic Gestures in Violin Performance and Their Modification by Early Recording and Playback Devices (1901–1933)

To what extent did early recording technology affect the creation and representation of musical performances? According to Mark Katz (from 1999 onwards), historical studio environments led to crucial shifts in 20th century violin performances due to the restrictions imposed by early recording and reproduction devices (“phonograph effects”). In particular, this may have affected sonic gestures that include expressive means such as vibrato, portamento, articulation, and timbre variation. In order to trace potential modifications, we reenacted a 1911 “Liebesleid” performance by one of the most influential violinists of the 20th century, Fritz Kreisler. We then digitally ascertained the full acoustic transfer paths (impulse responses, IRs) from the 1911 studio to 20 historical gramophone setups and applied them to the reenactment. In this way, for the first time, our study generated comparative IR findings across multiple gramophones, soundboxes, and horns built by different manufacturers between 1901 and 1933. Sonic gestures were found to induce significant level modifications of up to 20 dB due to the devices’ resonances, leading to dynamical variations that have never been part of the performance. Accordingly, Kreisler's famous “golden tone” is due, in part, to the recording technologies of his time. Therefore, early recordings should not be understood as “neutral witnesses” but rather as artifacts with substantial influence on the creation and reproduction of musical performance(s).

In Vivo Cavitation-Based Aberration Correction of Histotripsy in Porcine Liver.

Histotripsy is a noninvasive ablation technique that focuses ultrasound pulses into the body to destroy tissues via cavitation. Heterogeneous acoustic paths through tissue introduce phase errors that distort and weaken the focus, requiring additional power output from the histotripsy transducer to perform therapy. This effect, termed phase aberration, limits the safety and efficacy of histotripsy ablation. It has been shown in vitro that the phase errors from aberration can be corrected by receiving the acoustic signals emitted by cavitation. For transabdominal histotripsy in vivo, however, cavitation-based aberration correction (AC) is complicated by acoustic signal clutter and respiratory motion. This study develops a method that enables robust, effective cavitation-based AC in vivo and evaluates its efficacy in the swine liver. The method begins with a high-speed pulsing procedure to minimize the effects of respiratory motion. Then, an optimal phase correction is obtained in the presence of acoustic clutter by filtering with the singular value decomposition (SVD). This AC method reduced the power required to generate cavitation in the liver by 26% on average (range: 0%-52%) and required ~2 s for signal acquisition and processing per focus location. These results suggest that the cavitation-based method could enable fast and effective AC for transabdominal histotripsy.

A Gas Flow Measurement System Based on Lead Zirconate Titanate Piezoelectric Micromachined Ultrasonic Transducer.

Ultrasonic flowmeter is one of the most widely used devices in flow measurement. Traditional bulk piezoelectric ceramic transducers restrict their application to small pipe diameters. In this paper, we propose an ultrasonic gas flowmeter based on a PZT piezoelectric micromachined ultrasonic transducer (PMUT) array. Two PMUT arrays with a resonant frequency of 125 kHz are used as the sensitive elements of the ultrasonic gas flowmeter to realize alternate transmission and reception of ultrasonic signals. The sensor contains 5 × 5 circular elements with a size of 3.7 × 3.7 mm2. An FPGA with a resolution of ns is used to process the received signal, and a flow system with overlapping acoustic paths and flow paths is designed. Compared with traditional measurement methods, the sensitivity is greatly improved. The flow system achieves high-precision measurement of gas flow in a 20 mm pipe diameter. The flow measurement range is 0.5-7 m/s and the relative error of correction is within 4%.

Cavitation cloud formation and surface damage of a model stone in a high-intensity focused ultrasound field

This work investigates the fundamental role of cavitation bubble clouds in stone comminution by focused ultrasound. The fragmentation of stones by ultrasound has applications in medical lithotripsy for the comminution of kidney stones or gall stones, where their fragmentation is believed to result from the high acoustic wave energy as well as the formation of cavitation. Cavitation is known to contribute to erosion and to cause damage away from the target, yet the exact contribution and mechanisms of cavitation remain currently unclear. Based on in situ experimental observations, post-exposure microtomography and acoustic simulations, the present work sheds light on the fundamental role of cavitation bubbles in the stone surface fragmentation by correlating the detected damage to the observed bubble activity. Our results show that not all clouds erode the stone, but only those located in preferential nucleation sites whose locations are herein examined. Furthermore, quantitative characterizations of the bubble clouds and their trajectories within the ultrasonic field are discussed. These include experiments with and without the presence of a model stone in the acoustic path length. Finally, the optimal stone-to-source distance maximizing the cavitation-induced surface damage area has been determined. Assuming the pressure magnitude within the focal region to exceed the cavitation pressure threshold, this location does not correspond to the acoustic focus, where the pressure is maximal, but rather to the region where the acoustic beam and thereby the acoustic cavitation activity near the stone surface is the widest.

Non-linear Acoustic Problems in Loudspeaker Design

The article deals with the issues of non-linear acoustics. A mathematical model of non-linear distortions of the acoustic path has been compiled in relation to the operation of a loudspeaker in a piston mode. The results of experimental measurements are presented and analyzed. Recommendations are given to reduce distortion in the construction of high-quality acoustic systems.

An adaptive algorithm for acoustic feedback compensation and secondary path identification of an active noise control system.

An adaptive variable step-size algorithm is proposed in this paper to address the impact of the real-time acoustic feedback and the real-time secondary path identification on the overall noise reduction performance of an active noise control system. An automated adjustment weight factor is introduced in the algorithm to accelerate the convergence of the acoustic feedback path as well as the secondary path identification, and to prevent possible system divergence. It is shown in this study that the proposed algorithm can resolve the trade-off between a fast convergence and a low misalignment of the virtual and the actual control paths typically found in conventional algorithms. An optimized control structure is also proposed in the study by enabling an adaptive gain adjustment based on the output of the auxiliary filter to enhance the practicality of the control system. The effectiveness of the algorithm is tested using two simulated multi-component signals and a broadband noise signal, and the results confirm that the proposed algorithm can achieve a good noise reduction with only a few iterations.

Frequency domain online secondary path modelling for active noise control without auxiliary noise

The identification of the secondary path transfer function is of vital importance for active noise control (ANC) system. Online secondary path modeling method is preferable to offline modeling due to its tracking capability in time-varying acoustic environments. However, the auxiliary noise of online modeling mixed with the residual error signal diminishes the noise control performance. In this paper, we propose a frequency domain online secondary path modelling algorithm based on our previous work which achieves simultaneous acoustic paths modeling and noise control without auxiliary noise. The uniqueness of the solution is theoretically analyzed, and the computational burden is shown significantly lower than the previously proposed method. Simulations are conducted to verify that the proposed algorithm also has a better convergence behavior.

Variation of the secondary acoustic paths from loudspeakers at the seat shoulder in an automobile cabin

The secondary path is essential in the design of adaptive active noise control systems, and it varies with several factors in practical implementation. In this paper, the acoustic responses from secondary loudspeakers installed at the shoulder of the front passenger seat to the error microphones at the passenger's ears in an automobile cabin are measured, when the factors including the passenger movement, the seat posture and the passenger number change. The upper limit frequency where the phase variation is within 90 deg. compared to the reference position is analyzed. The results show that the state of both the passenger head and the seat back determines the lowest upper limit frequency among all the factors under investigation. If multiple factors change at the same time, the upper limit frequency will be further reduced.

Practical Considerations for Implementing Adaptive Acoustic Noise Cancellation in Commercial Earbuds

Active noise cancellation has become a prominent feature in contemporary in-ear personal audio devices. However, due to constraints related to component arrangement, power consumption, and manufacturing costs, most commercial products utilize fixed-type controller systems as the basis for their active noise control algorithms. These systems offer robust performance and a straightforward structure, which is achievable with cost-effective digital signal processors. Nonetheless, a major drawback of fixed-type controllers is their inability to adapt to changes in acoustic transfer paths, such as variations in earpiece fitting conditions. Therefore, adaptive-type active noise control systems that employ adaptive digital filters are considered as the alternative. To address the increasing system complexity, design concepts and implementation strategies are discussed with respect to actual hardware limitations. To illustrate these considerations, a case study showcasing the implementation of a filtered-x least mean square-based active noise control algorithm is presented. A commercial evaluation board accommodating a low-cost, fixed-point digital signal processor is used to simplify operation and provide programming access. The earbuds are obtained from a commercial product designed for noise cancellation. This study underscores the importance of addressing hardware constraints when implementing adaptive active noise cancellation, providing valuable insights for real-world applications.

Acoustic cloaking design based on penetration manipulation with combination acoustic metamaterials

The acoustic wave transmission manipulation ability is the most important performance for the acoustic metamaterials. To manipulate the acoustic transmission, the combination acoustic metamaterials structures are involved, and the two-directional acoustic penetration cloaking scheme are constructed. The combination acoustic metamaterials include chiral metamaterials and self-collimation metamaterials, the acoustic wave transmission path are manipulated to bypass from the acoustic scattering target in the penetration cloaking, and the target scattering stealth problem are effectively solved. In the end, the acoustic transmission manipulation performances are verified by numerical analysis with a finite-width acoustic metamaterial structure plates. The results provide technical support for design and application for acoustic transmission manipulation with acoustic metamaterials.

Simultaneous reconstruction of 3D non-uniform temperature and velocity fields in a furnace using a bidirectional acoustic path separation tracking method

Acoustic measurement techniques applied to furnace measurements are based on the coupling of multiple fields, such as sound, temperature, and flow. To better measure high-temperature fluids within furnaces using acoustic technology, this study establishes a physical model that separates the bidirectional propagation path of sound. Additionally, a novel nonlinear acoustic ray-tracing method is proposed that allows the simultaneous measurement of temperature and flow. The combustion process of high-temperature swirling flow in a furnace is simulated, the effective path of sound propagation is tracked, and the existence of a sound shadow zone in the low-temperature jet region of the burner is discovered. After reasonably arranging sensor positions, three-dimensional nonuniform temperature and complex flow fields are simultaneously reconstructed by combining ray tracing and nonlinear acoustic tomography. The feasibility of the method is analyzed via the error analysis of the computational fluid dynamics simulation data and the reconstructed data. The proposed method provides a solution for improving the existing acoustic measurement techniques in furnaces.

Acoustic signals received on buoyancy gliders in the Beaufort Sea

The buoyancy glider is a quiet and persistent underwater acoustic receiving platform. Traveling in a sawtooth pattern, buoyancy gliders equipped with acoustic recorders can sample acoustic transmissions at many ranges and depths with respect to moored acoustic sources transmitting on a timed schedule. In the Beaufort Sea, six broadband acoustic tomography sources consecutively transmitted 135-s linear frequency modulated (LFM) swept-frequency signals centered near 250 Hz every 4 h. These signals were received by two Seagliders at ranges up to 500 km and depths between the surface and 800 m in the summer of 2017. Sources were moored within the Beaufort Duct, a sound-speed minimum characteristic of the region, at a depth of approximately 180 m. Due to the presence of this duct, many acoustic paths are focused within a relatively narrow depth span, resulting in a complicated arrival structure. Pulse-compressed acoustic signals received on the gliders are interpreted in the context of broadband acoustic arrival predictions. The individual snapshots of acoustic arrival structure that make up this unique dataset offer insight into the acoustic travel-time arrival structure as it evolves with range from a transmitting source.

Using long-range transmissions in the Beaufort Gyre to test the sound-speed equation at high pressure and low temperature.

An ocean acoustic tomography array with a radius of 150 km was deployed in the central Beaufort Gyre during 2016-2017 for the Canada Basin Acoustic Propagation Experiment. Five 250-Hz transceivers were deployed in a pentagon, with a sixth transceiver at the center. A long vertical receiving array was located northwest of the central mooring. Travel-time anomalies for refracted-surface-reflected acoustic ray paths were calculated relative to travel times computed for a range-dependent sound-speed field from in situ temperature and salinity observations. Travel-time inversions for the three-dimensional sound-speed field consistent with the uncertainties in travel time [∼2 ms root mean square (rms)], receiver and source positions (∼ 3 m rms), and sound speed calculated from conductivity-temperature-depth casts could not be obtained without introducing a deep sound-speed bias (below 1000 m). Because of the precise nature of the travel-time observations with low mesoscale and internal wave variability, the conclusion is that the internationally accepted sound-speed equation (TEOS-10) gives values at high pressure (greater than 1000 m) and low temperature (less than 0 °C) that are too high by 0.14-0.16 m s-1.

Optimizing transducer aperture subdivision for aberration correction during transabdominal histotripsy

This study investigated the effect of transducer aperture subdivision on aberration correction performance for transabdominal histotripsy. A transducer aperture and geometric curvature similar to clinical histotripsy devices (750 kHz, 20 × 16 cm width, 14 cm radius of curvature) was subdivided into 64, 256, and 1024 elements (10.7λ, 5.3λ, 2.6λ). For each of the three designs, optimal space filling (100%) equal area polygons with a pseudo-random arrangement of elements was used following the technique described by Rosnitskiy. 3D acoustic path maps were constructed from abdominal CTs of 3 de-identified human subjects and assigned acoustic properties from literature. For each transducer, acoustic transmission was simulated using k-Wave at 3 target locations in the liver of each subject with and without implementing ideal aberration correction. Across all subjects and targets (n = 9), AC increased the maximum focal pressure amplitude by 26% (0%-59%) on average for 64 elements, 38% (5%-84%) for 256 elements, and 42% (7%–92%) for 1024 elements. These results suggest 5.3λ elements may near an optimal subdivision for transabdominal histotripsy aberration correction when taking into account the cost of transducer and driving system fabrication. Acoustic simulations can save fabrication time and costs when optimizing device design.

Robust improved multiband-structured subband adaptive filter for active noise control with impulsive interference

The feedforward filtered-x least mean square algorithm is extensively implemented for active control of broadband noise. However, the control performance is substantially deteriorated due to colored noise and the presence of uncorrelated disturbances near the reference and error sensors. To tackle these issues, in this paper, a robust improved multiband-structured subband adaptive filter based on logarithmic and total least squares method is proposed for active control. Unlike the conventional method of total least squares, the proposed algorithm adopts logarithmic and Rayleigh quotient functions. The closed loop implementation of the improved multiband-structured subband adaptive filter is adopted to meet the delayless requirement. The proposed algorithm is well-suited for environments where the reference signal is highly correlated and the residual noise is contaminated by impulsive noise. Furthermore, an affine combination of the proposed algorithm is developed to meet the complementary requirements of faster convergence and improved noise reduction. Eventually, the stability and computational complexity are studied. Simulation results using measured acoustic paths in an anechoic chamber and a normal room illustrate the effectiveness of the proposed algorithm for controlling broadband noise with impulsive interference. In addition, the tracking control performance is evaluated in a time-varying acoustic environment.

Feature extraction and classification of deep-sea mobile underwater acoustic channels

The reliable acoustic path (RAP) is one of the crucial channels for deep-sea sound propagation, which is affected weakly by the interface and has lower transmission loss, enabling long-distance communication. However, RAP-based deep-sea acoustic communication may face channel model mismatch issues. In order to analyze the dynamic characteristics of spatial-temporalvariability channels, deep-sea mobile underwater acoustic channel measurement experiments were conducted. This work proposes a deep learning method based on multi-dimensional properties to classify deep-sea channels. Specifically, the sound ray convergence zone leads to a complex multipath structure and severe delay spread in the RAP channel. The fuzzy c-means (FCM) algorithm is used for multipath clustering to extract accurate channel features, and then the Markov chain (MC) is introduced to track the evolution characteristics of multipath clusters. Finally, the coupling features of channel time-variant impulse response (TVIR) and multi-dimensionalstatistical properties are used as the input of convolutional neural networks (CNNs) to obtain the quantitative evaluation index as the channel classification to build a channel feature dataset for underwater mobile platforms. This dataset can effectively assist in identifying deep-sea mobile channels and promote the development of adaptive underwater acoustic communication systems on mobile platforms.

3D reconstruction of nonuniform and unsteady flow velocity distribution using nonlinear acoustic ray tracing and tomography

The nonuniform and unstable gas flow distribution at the air inlets of the boiler combustion chamber can negatively affect the energy efficiency and safety of the boiler. Accurately reconstructing the flow velocity inside the furnace in three dimensions can help the boiler automatically adjust the air supply to reduce unwanted energy waste and gas emissions.In this study, we propose a novel method for three-dimensional velocity reconstruction based on nonlinear acoustic ray tracing and tomography. The model provides the equation of acoustic ray motion in the flow field, which includes spatial and temporal parameters. During the process of measuring flow velocity, higher precision reconstruction of the three-dimensional velocity distribution was achieved by combining acoustic refractive paths based on derivative-free optimization iteration updates with radial basis functions that use Gaussian kernels.The computational time cost and reconstruction accuracy of the proposed algorithm were analyzed numerically and through simulations. The results indicate that the method incorporating acoustic ray tracing greatly improves the reconstruction accuracy of large gradient nonuniform flow fields. Additionally, we analyzed the impact of different numbers of sound tracing paths on reconstruction quality and computation time, providing a reference for the rational placement of microphones and the selection of the most efficient paths in boilers.Experimental results show that this method has good reconstruction capabilities for nonuniform flow fields and practical applications.

REGULARITIES OF THE FIELD FOCUS OF THE THROUGH-TYPE ELECTROMAGNETIC ACOUSTIC TRANSDUCER OF TRANSVERSE WAVES

The article presents the results of experimental and theoretical research of the influence of the characteristics of a through-type electromagnetic-acoustic transducer and testing object on the focusing parameters of transverse waves using COMSOL Multiphysics. It is shown that in the radial plane of the section, the formation of a converging spherical front is observed, in the axial plane – close to a flat front. The influence on the focusing factor and the diameter of the focal spot of the diameter of the object, the operating frequency and the quality factor of the excitation pulse is presented. The developed model of the formation of the focus zone of the through-type EMAT can be used in the analysis of the acoustic path of the mirror-shadow method of multiple shadow, depending on the characteristics of the object and control parameters.