Acidic Properties Research Articles

STUDY OF CATALYTIC BEHAVIOURS OF THE SPINEL STRUCTURE NdxMg1- xAl2O4 COMPOSITION WITH ZSM-5 ZEOLITE IN ETHYLBENZENE DISPROPORTIONATION

Nanosized (10–15 nm) powders of spinel structures NdxMg1–xAl2O4 were obtained by low-temperature combustion of aluminium, magnesium, neodymium nitrate solutions, diethylmalonate, and hydrazine monohydrate with further calcination of nanopowders at 1000 °C, which were used in the preparation of catalytic compositions with ZSM-5 zeolite. The obtained catalytic compositions were characterized by X-ray diffraction, pyridine adsorption, and low-temperature nitrogen adsorption. The acidic properties and porosity of the catalysts were altered by controlling the concentration of nanopowder (1.0–7.0 wt.%) in the catalytic composition. The interaction of the modifier with HZSM-5 zeolite leads to a decrease in specific surface area and pore volume, as well as reduse of strong Bronsted acid sites (B) and an increase in the concentration of medium Lewis acid sites (L), resulting in a change in the B/L ratio from 3.61 to 0.23. The ongoing variations contributed mainly to an enhancement of the para-selectivity of the catalytic composition in the ethylbenzene disproportionation reaction. The catalytic composition of 5% Nd0.1Mg0.9Al2O4 with a pore volume of 0.15 cm3/g and an acid site B/L ratio of 0.27 demonstrates a maximum selectivity to p-diethylbenzene of 75.6% with a conversion of ethylbenzene of 23.7%.

Hierarchical fluoride-containing zeolite Y supported Ru for catalytic conversion of xylose to xylitol

Hierarchical fluoride-containing zeolite HY (Hie-HY(F)) is an interesting material because it tunes both a high mesoporosity and a moderate acid property, which could benefit the transformation of xylose to xylitol. Herein, we synthesized a new Hie-HY(F) by etching NH4Y with ammonium fluoride (NH4F) under ultrasonication at 60 °C for 20, 40, and 60 min. After etching with NH4F solution, the Hie-HY(F)s contained fluoride in the zeolite frameworks with high mesoporosity and moderate acid properties. The sonication time longer than 20 min caused the structure to collapse rather than the creation of mesoporosity. The Hie-HY(F)s were further used as supports for the Ru catalyst. When loaded with Ru precursor and calcined in air, RuO2 phase was formed in all catalysts. The RuO2 supported on Hie-HY(F)s had a lower reduction temperature than that on HY. Ru supported on Hie-HY(F)-20 gave the reactivity of xylose conversion to xylitol, the highest yield of 80.1 %, providing the reusability up to four cycles.

Physicochemical and functional properties of short-chain fatty acid starch modified with different acyl groups and levels of modification

Rice and quinoa starches are modified with short-chain fatty acids (SCFA) with different SCFA acyl chain lengths and levels of modification. This work is aimed to investigate the impact of modifying rice and quinoa starches with short-chain fatty acids (SCFAs) on various physicochemical properties, including particle size, protein and amylose content, thermal behavior, pasting characteristics, and in vitro digestibility. Both native and SCFA-starches showed comparable particle sizes, with rice starches ranging from 1.58 to 2.22 μm and quinoa starches from 5.18 to 5.72 μm. SCFA modification led to lower protein content in both rice (0.218–0.255 %) and quinoa starches (0.537–0.619 %) compared to their native counterparts. Esterification led to the reduction of gelatinization and pasting temperatures as well as the hardness of the paste of SCFA-starches were reduced while paste clarity increased. The highest level of modification in SCFA-starch was associated with the highest amount of resistant starch fraction. Principal component analysis revealed that modification levels exerted a greater influence on starch properties than the types of SCFA used (acetyl, propionyl, and butyryl). These findings is importance in considering the degree of substitution or level of modification when tailoring starch properties through SCFA modification, with implications for various applications in food applications.

THz spectroscopy on the amino acids L-serine and L-cysteine.

We present a detailed study on the temperature-dependent THz spectra of the polycrystalline amino acids, L-serine and L-cysteine, for wavenumbers from 20 to 120cm-1 and temperatures from 4 to 300K. Even though the structure of these two amino acids is very similar, with a sulfur atom in the side chain of cysteine instead of an oxygen atom in serine, the excitation spectra are drastically different. Obviously, the vibrational dynamics strongly depend on the ability of cysteine to form sulfur-hydrogen bonds. In addition, cysteine undergoes an order-disorder type phase transition close to 80K, documented by additional specific heat experiments, with accompanying anomalies in the THz results. On increasing temperatures, well-defined vibrational excitations exhibit significant shifts in the eigenfrequencies with concomitant line-broadening yielding partly overlapping modes. Interestingly, several modes completely lose all their dipolar strength and are unobservable under ambient conditions. Comparing the recent results to the published work utilizing THz, Raman, and neutron-scattering techniques, as well as with abinitio simulations, we aim at a consistent analysis of the results ascribing certain eigenfrequencies to distinct collective lattice modes. We document that THz spectra can be used to fine-tune the parameters of model calculations and as fingerprint properties of certain amino acids. In addition, we analyzed the low-temperature heat capacity of both the compounds and detected strong excess contributions compared to the canonical Debye behavior of crystalline solids, indicating soft excitations and a strongly enhanced phonon-density of states at low frequencies.

Effect of Aging on Tensile and Chemical Properties of Polylactic Acid and Polylactic Acid-Like Polymer Materials for Additive Manufacturing.

Additive manufacturing, with its fast development and application of polymeric materials, led to the wide utilization of polylactic acid (PLA) materials. As a biodegradable and biocompatible aliphatic polyester, produced from renewable sources, PLA is widely used in different sectors, from industry to medicine and science. The aim of this research is to determine the differences between two forms of the PLA material, i.e., fused deposition modeling (FDM) printed filament and digital light processing (DLP) printed resin, followed by aging due to environmental and hygiene maintenance conditions for a period of two months. Specimens underwent 3D scanning, tensile testing, and Fourier transform infrared (FTIR) spectrometry to obtain insights into the material changes that occurred. Two-way Analysis of Variance (ANOVA) statistical analysis was subsequently carried out to determine the statistical significance of the determined changes. Significant impairment can be observed in the dimensional accuracies between both materials, whether they are non-aged or aged. The mechanical properties fluctuated for aged FDM specimens: 15% for ultimate tensile stress, 15% for elongation at yield, and 12% for elastic modulus. Regarding the DLP aged specimens, the UTS decreased by 61%, elongation at yield by around 61%, and elastic modulus by 62%. According to the FTIR spectral analysis, the PLA materials degraded, especially in the case of resin specimens. Aging also showed a significant influence on the elastic modulus, ultimate tensile stress, elongation at yield, elongation at break, and toughness of both materials, which was statistically shown by means of a two-way ANOVA test. The data collected in this research give a better understanding of the underlying aging mechanism of PLA materials.

Introduction of an electrospun nanofibrous membrane incorporated by metal-organic framework-199 (MOF-199) with Lewis acid property for efficient extraction of sulfonamides in on-chip electromembrane extraction

In this study, a new supporting polymeric membrane having Lewis acid nature was introduced for immobilizing organic solvent in on-chip electromembrane extraction (on-chip EME). For this aim, a polymeric nanofibrous membrane incorporated by a copper based metal-organic framework (MOF-199), with coordinatively unsaturated metal sites and Lewis acid property, was prepared by electrospinning a mixture of polycaprolactone (PCL) and MOF-199. Based on the field emission scanning electron microscopy images, the obtained polymeric membrane consisted of intertwined nanofibers having empty space between the fibers which could provide a suitable place for immobilizing the organic solvent. To demonstrate remarkable extractability of the proposed membrane (PCL/MOF-199 nanofibers) via executing Lewis acid-base interactions, three sulfonamide drugs was selected as anionic polar analytes with Lewis base feature. The parameters affecting the extraction efficiency of the method were optimized through the experimental design method using the orthogonal and rotatable central composite design (CCD). Under optimum conditions, the extraction recoveries ranging from 35.5 to 71.2 %, the relative standard deviations (RSD%) less than 6.45 %, and the detection limits in the range of 0.2–0.5 μg L−1 were achieved. The comparison of the extraction efficiency of the on-chip EME method using the electrospun PCL/MOF-199 nanofibers and PCL nanofibers membranes indicated that the proposed membrane was more efficient for extraction of sulfonamides because of the significant Lewis acid-base interactions of sulfonamides with copper uncoordinated open sites in MOF-199. Finally, the performance of the proposed method for extraction and determination of sulfonamides in three real samples was assayed.

The inspection of ciprofloxacin retention on poly ether ether ketone (sPEEK) based sorbents considering its solubility and acidic properties

This study examines the conditions for removing Ciprofloxacin (CIP) from aqueous solutions with the aid of sulfonated poly ether ether ketone (sPEEK) polymer and its derivatives — ionic-liquid functionalised sPEEK (sPEEK-IL) and ionic-liquid and chitosan (CH) incorporated sPEEK (sPEEK/IL-CH). The effects of key parameters including contact time, solution pH and CIP concentration on adsorption were investigated by batch experiments. Characterisation of adsorbents were performed by FT-IR, SEM, TGA, BET/N2 surface area, particle size analysis and alkalimetric titration. Kinetic results showed that equilibrium was achieved in the first 60, 20 and 30 mins of contact for sPEEK, sPEEK/IL and sPEEK/IL-CH, respectively. CIP adsorption on sPEEK and composites showed the highest fit with pseudo-second order model (R2 > 0.99). Equilibrium behaviour of all adsorbents could be well-described by Langmuir isotherm. The assessment of retaining mechanisms of CIP was achieved by analysing the species distributions on sPEEK surface and CIP. The results revealed that electrostatic and π-π interactions played pivotal roles in CIP retention, accompanied by pore diffusion and hydrogen bonding. Overall, by exhibiting high capacity and rapid CIP adsorption, low-cost sPEEK and its derivatives with IL and CH show promising potential for elimination of CIP from wastewaters.

Photophysical Properties of Sinapic Acid and Ferulic Acid and Their Binding Mechanism with Caffeine.

Sinapic acid (SA) and ferulic acid (FA) are bioactive compounds used in the food, pharmaceutical, and cosmetic industries due to their antioxidant properties. In this work, we studied the photophysical properties of SA and FA in different solvents and concentrations and their interactions with caffeine (CF), using ultraviolet-visible (UV-Vis), fluorescence spectroscopy and Fourier transform infrared (FTIR) spectroscopy. The findings show that the quantum yield, fluorescence lifetime, radiative decay rates, and non-radiative decay rates of SA and FA are influenced by the concentrations and solvent polarity. The interaction between SA and FA with CF was also studied using UV-Vis and fluorescence spectroscopy. The results indicate that the CF quenched the fluorescence intensity of SA and FA by static quenching due to the formation of a non-fluorescent complex. The van't Hoff equation suggests that the van der Waals forces and hydrogen bonds force were responsible for the interaction between SA and CF, as indicated by a negative change in enthalpy ( < 0) and a negative change in entropy ( < 0). On the other hand, the interaction between FA and CF was primarily controlled by electrostatic force, as indicated by a negative change in enthalpy ( < 0) and a positive change in entropy ( > 0). The negative change in Gibbs free energy ( ) indicates that both compounds underwent a spontaneous binding process.

Hydrogen transfer reaction in butene catalytic cracking over ZSM-5

Hydrogen transfer reaction (HTR) is the pivotal side reaction in the catalytic cracking process of low carbon olefins. The intricate reaction pathways and product diversity of HTR directly impact the selective formation of ethylene and propylene. Therefore, elucidating the key HTR in various reaction pathways and defining the hydrogen transfer index (HTI) as a criterion lay a scientific foundation for precisely regulating HTR during olefin catalytic cracking process. Herein, the influence of the acid strength of ZSM-5 zeolites on the HTR degree was analyzed in butene catalytic cracking. Results showed that isobutane was the predominant component of HTR products, mainly derived from HTR during the dimerization-cracking of pentene (butene primary cracking product). Subsequent pentene catalytic cracking experiments validated this conclusion. Thus, the HTI in butene or pentene cracking process was defined as follows: for butene cracking process, HTI = Si–C4H10/SC5H10; for pentene cracking process, HTI = Si–C4H10/SC4H8. The HTI accurately reflected the extent of HTR with respect to the acid properties of the catalysts. Moreover, the reaction network of butene catalytic cracking process was optimized, providing a comprehensive explanation for the intriguing phenomenon of decreasing butene conversion with increasing reaction temperature when the acid strength of ZSM-5 was weak. Finally, a high-performance butene catalytic cracking catalyst, De-TS-1-0.25%P, was developed, exhibiting high olefin selectivity (92.33 %) and outstanding stability (307 h) in the conversion of butene.

Frustrated Lewis pairs created by Ce-doped Bi2MoO6: A universal strategy to promote efficient utilization of H2O2 for Fenton-like photodegradation

Photo-Fenton-like technology based on H2O2 is considered as an ideal strategy to generate reactive oxygen species (ROS) for antibiotic degradation, but O2 overflow in the process severely limits the utilization efficiency of H2O2. Herein, we fabricate Bi2MoO6 (BMO) photocatalyst modified with Frustrated Lewis pairs (FLPs) as a Fenton catalyst model for enhancing reuse of spilled O2. The FLPs created by the introduction of cerium and oxygen vacancy were found to contribute to regulate the electronic structure of BMO and further improve the acidic and basic properties of photocatalyst surface. More importantly, the frustrated acid and base sites can enhance the H2O2 and O2 interfacial adsorption process and provide an Ce4+-Ov-O2− active site on the surface of Ce-BMO nanosheets, which can promote O2/•O2−/1O2/H2O2 redox cycles to achieve high H2O2 utilization efficiency. Specifically, in the experiment using tetracycline as a photocatalytic degradation object, the degradation activity of Ce-BMO was 2.15 times higher than that of BMO pure phase. Quenching experiments and EPR assays also confirmed that 1O2 and •O2− were the dominant oxidative species. This study systematically reveals the design of Fenton photocatalytic active sites at the atomic scale and provides new insights into constructing FLPs photocatalysts with high H2O2 utilization efficiency.

Nutritional evaluation, amino acid, and fatty acid properties of boiled ackee arils

Nutritional evaluation, amino acid, and fatty acid properties of boiled ackee arils

A bio-degradable, triboelectric self-stimulated herbal transdermal therapeutic dressing for healing massive chronic wound

Homogeneous controlled release of active ingredients, avoiding secondary damage of dressing changes would be considerable advance for transcutaneous drug delivery treatment. Here, a bio-degradable, self-stimulated herbal transdermal therapeutic dressing (irritability) driven by multi-ball nimble-rolling triboelectric nanogenerator (mbnr-TENG) is proposed that provided a stable and adjustable triboelectric field for controlling drug release. The mbnr-TENG deliver a periodic triboelectric field of 140 V for herbal dressings by collecting human mechanical energy to enhance transdermal properties of total flavonoids and chlorogenic acid in ss-HTTD by 310% and 147%. Following a therapeutic cycle using ss-HTTD, the secretion of inflammatory factors decreased by 50.35%, and wound healing rate increased by 24.98%, then completely degraded after 10 days. As a new drug delivery system, this work holds great potential in healing massive chronic wound, ss-HTTD is advantageous in controlling drug release, enhancing the activity and the long-term stability of herbal medicines.

NIR-II luminescent nanoparticles based-Theranostic platform for drug-induced liver injury diagnoses and ameliorates

Precise diagnosis followed by prompt treatment of drug-induced liver injury (DILI) is vital to prevent its progression to other liver diseases, even liver failure. Reactive oxygen species (ROS) are recognized as an early sign in the progression of DILI. However, ROS-centric diagnosis and therapy of DILI are still unsatisfactory due to methodological limitations. In this work, a rationally designed theranostic nanoplatform was developed by integrating lanthanide-doped second near-infrared (NIR-II) luminescent nanoparticles with salvianolic acid B and Fe3+. Here, NaGdF4:3%Nd@NaGdF4 with NIR-II emission was synthesized and transferred to the aqueous solution via capping with the amphiphilic polymer, C18PMH-mPEG. Upon loading the salvianolic acid B and Fe3+ complex (Sal B/Fe) into the polymer, the NIR-II luminescence of nanoparticles was quenched through the absorption competitive-induced emission (ACIE) principle. However, ROS generated in the DILI can restore the NIR-II luminescence as the Sal B/Fe was destroyed by the ROS. On the other hand, the nanosystem could efficiently alleviate the oxidative stress of DILI via scavenging ROS thanks to the antioxidant properties of salvianolic acid B. Liver injury-related symptoms, including histopathological biochemical serological indicators, expression of SOD, GSH, and malondialdehyde were evidently mitigated.

Facile one-pot synthesis of niobium-containing carbon nitride and the catalytic application for synthesis of dimethyl carbonate

Dimethyl carbonate (DMC) is a building block in wide chemical-related fields and the transesterification of ethylene carbonate (EC) and methanol/ethanol is a sustainable route for the synthesis of DMC. Herein, in order to explore efficient heterogeneous catalysts, niobium-containing carbon nitride materials were synthesized by a convenient one-pot calcination method. By reserving the main chemical functionalities of carbon nitride, the Nb-CN composites contained both acidic and basic properties, and Nb can be dispersed by carbon nitride. In the transesterification of EC with methanol, under the reaction temperature of 140 °C and reaction time of 4 h, the conversion of EC and the selectivity of DMC reached 53.8% and 100%, respectively, and the activity of the catalyst did not decrease significantly after several recycling runs. Furthermore, the Nb-CN could promote transesterification reactions of other cyclic carbonate and alcohols.

Understanding contributions of zeolite surface hydroxyl groups over Au/USY in selective oxidation of aromatic alcohols

Metal-zeolites catalysts are of great importance in selective organic conversions. Zeolites possess features of highly-ordered porous network, adjustable acidic properties (Brønsted/Lewis), spatial nanoconfinement effects, unique shape selectivity and the strong (hydrothermal-) stability. The role of zeolite hydroxyl (z-OH) groups, such as bridging ones in Si-O(H)-Al (B acids) and terminal ones in Al-OH and Si-OH (silanols), in catalysis is an interesting topic, particularly when they are not catalytic active sites, while they affect the catalytic performances. This study comprehensively investigated series of Au/USY catalysts in the selective oxidation of benzyl alcohol to benzaldehyde and clarified the dominating contributions of Al-associated z-OH groups to affecting catalytic conversions and selectivity via altering the Si/Al ratio and reducing z-OH groups by amorphous silica species derived from diethoxydimethylsilane under high-temperature calcination. The catalysts were characterized by XRD, BET, TEM, XPS, UV/Vis, FT-IR and in-situ DRIFT to investigate crystal structures, textural properties, morphologies, size distribution, chemical state of gold, acidity, and adsorptive properties. The experimental results proved that zeolites with a higher amount of z-OH groups tuned by Si/Al ratios or by diethoxydimethylsilane silylation exhibited higher catalytic activity because of the adsorption effect. Finally, a possible mechanism was discussed based on the experimental results and literature.

Exploration of electronic and vibrational properties of sulfanilic acid through periodic and non-periodic DFT calculations.

The electronic, discrete water solvation, and vibrational properties of zwitterionic sulfanilic acid were thoroughly investigated using periodic and non-periodic DFT approaches. The periodic-DFT results, obtained by employing the PBE-TS functional (Perdew-Burke-Ernzerhof (PBE) functional with the Tkatchenko and Scheffler (TS) dispersion correction) were first presented in order to analyze the band structures of the studied crystal. An attentive reading of the predicted band structures has shown three lowest gap energies calculated at 4.23, 4.24, and 4.29eV arising from the Γ→Γ, Γ→Z, and Γ→S transitions, respectively. Then, non-periodic calculations were carried out, at the B3LYP-D3 level of theory (B3LYP functional with the D3 Grimme dispersion correction) in order to optimize the sulfanilic acid-(H2O)10 complex. Starting from the optimized structure, non-covalent interaction calculations were performed and the H-bonding, van der Waals, and steric effect interactions were identified. Finally, the PBE-TS calculations were strengthened by conducting anharmonic B3LYP-D3 calculations in order to achieve a complete decryption of the experimental IR spectrum of sulfanilic acid. The spectral analysis is not limited only to the interpretation of both the NH/CH stretching and fingerprint regions but also extended to the 1800-2600cm-1 region, which is characterized by a strong anharmonic effect. In the latter wavenumber region, the large experimental IR band centered at 1937cm-1 is reproduced theoretically employing the anharmonic B3LYP-D3 calculations. The similarity of this band with those usually considered as a fingerprint of zwitterionic amino acids is observed, and its origin is elucidated theoretically. In the vibrational spectroscopy field, the calculations presented in this study are probably the most appropriate for achieving vast analysis and accurate assignments of vibrational spectra of hydrogen bonding compounds recorded in the solid state. The periodic and non-periodic calculations were conducted within the Density Functional Theory (DFT) using the Generalized Gradient Approximation (GGA) at the PBE-TS level of theory and B3LYP-D3 functional with the 6-311++G(d,p) basis set, respectively. The PBE-TS and B3LYP-D3/6-311++G(d,p) calculations were performed using the CASTEP and Gaussian 09 programs, respectively. In addition, The non-covalent interactions were calculated by the Multiwfn 3.8 software. The obtained results for different calculations were visualized by employing the visualization tools in Materials Studio, GaussView, VMD, and Gnuplot programs.

Improving the stability and reactivity of SAPO-11 catalyst for gas-phase beckmann rearrangement by a simple and effective alkali-treated approach

ε-Caprolactam (CPL) is an important organic chemical raw material for preparing nylon-6 fiber and polyamide engineering plastics. Traditional production technology based on concentrated sulfuric acid leads to serious environmental pollution. Herein, we develop an economical and environmentally friendly strategy based on SAPO-11 molecular sieve as catalyst to produce CPL. Importantly, alkali engineering strategy to treat SAPO-11 molecular sieve was profited to remove the framework P and increase much Si island edge structures, consequently formatting the larger mesopores and enhancing the acidic properties, thus the catalytic performance and stability of the catalyst were significantly improved. Compared with the original SAPO-11, SAPO-11-TH had outstanding catalytic performance, the conversion of CHO and the selectivity for CPL were still more than 92% and 87% respectively when the reaction continuous reacted for 5 h at 6 h−1 weight hourly space velocity (WHSV). Interestingly, we found that the reactants can complete the conversion within an extremely short residence time (0.86 s), thereby obtaining higher spatiotemporal yields. What else, the catalyst obtained from simple calcination still exhibited excellent catalytic performance. We provide a facile, intriguing and scalable approach to treat catalyst SAPO-11 molecular sieve to form larger mesopores and high acidic strength that can be applied in the many catalytic fields.

Synthesis and Analysis of Novel Hyaluronic Acid-Based Dual Photocrosslinkable Tissue Adhesive: An In Vitro Study.

Background Tissue adhesives are mainly used for aiding in the attachment of adjacent tissues or to nearby hard tissue surfaces. They promote the natural healing processes of the tissues, especially for less painful closure, simple application, no need for sutures following surgery, and localized drug release. This study aimed to synthesize and assess the properties of hyaluronic acid (HA)-based, dual photocrosslinkable tissue adhesive. Materials and methodology N-hydroxysuccinimide (NHS), 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide (EDC), HA, and polymethylmethacrylate, which served as a photoinitiator, were combined to synthesize a tissue adhesive. The prepared formulation was characterized, and its biocompatibility was assessed. Results Surface morphology, mechanical properties, and biological properties of the HA adhesive were comparable to those of conventional fibrin glue. Scanning electron microscopy (SEM) analysis showed the average size of the molecules, 10-25 mm in diameter, and also showed a smooth and nonporous surface. The specimens experienced maximum compressive stress of 0.06 ± 0.02 MPa, compressive strain of 3.07 ± 2.02, and a compressive displacement at break of 3.04 ± 1.23 mm, with a maximum force of 2.33 ± 0.07 N at break. The cytotoxicity assay results for HA and fibrin glue are almost equal. Conclusion HA-based photocrosslinkable tissue adhesive could be a potential biomaterial in various applications in the field of medicine, especially in soft tissue management.

Chronotropic and vasoactive properties of the gut bacterial short-chain fatty acids in larval zebrafish.

Short-chain fatty acids (SCFAs) produced by the gut bacteria have been associated with cardiovascular dysfunction in humans and rodents. However, studies exploring effects of SCFAs on cardiovascular parameters in the zebrafish, an increasingly popular model in cardiovascular research, remain limited. Here, we performed fecal bacterial 16S sequencing and gas chromatography/mass spectrometry (GC-MS) to determine the composition and abundance of gut microbiota and SCFAs in adult zebrafish. Following this, the acute effects of major SCFAs on heart rate and vascular tone were measured in anesthetized zebrafish larvae using fecal concentrations of butyrate, acetate, and propionate. Finally, we investigated if coincubation with butyrate may lessen the effects of angiotensin II (ANG II) and phenylephrine (PE) on vascular tone in anesthetized zebrafish larvae. We found that the abundance in Proteobacteria, Firmicutes, and Fusobacteria phyla in the adult zebrafish resembled those reported in rodents and humans. SCFA levels with highest concentration of acetate (27.43 µM), followed by butyrate (2.19 µM) and propionate (1.65 µM) were observed in the fecal samples of adult zebrafish. Immersion in butyrate and acetate produced a ∼20% decrease in heart rate (HR), respectively, with no observed effects of propionate. Butyrate alone also produced an ∼25% decrease in the cross-sectional width of the dorsal aorta (DA) at 60 min (*P < 0.05), suggesting compensatory vasoconstriction, with no effects of either acetate or propionate. In addition, butyrate significantly alleviated the decrease in DA cross-sectional width produced by both ANG II and PE. We demonstrate the potential for zebrafish in investigation of host-microbiota interactions in cardiovascular health.NEW & NOTEWORTHY We highlight the presence of a core gut microbiota and demonstrate in vivo short-chain fatty acid production in adult zebrafish. In addition, we show cardio-beneficial vasoactive and chronotropic properties of butyrate, and chronotropic properties of acetate in anesthetized zebrafish larvae.

Pharmacological Properties of Acetylsalicylic Acid and its Complex with Glycyrrhizic Acid as a Promising Dosage form (Review)

Pharmacological Properties of Acetylsalicylic Acid and its Complex with Glycyrrhizic Acid as a Promising Dosage form (Review)