ZnO Tetrapods Research Articles

Characterization and photocatalytic properties of zno tetrapods synthesized by high-temperature pyrolysis

The presented work presents the structural and morphological characterization and the results of studies of luminescent, photocatalytic properties of ZnO tetrapods synthesized by the method of high-temperature pyrolysis. It has been shown that the morphology and structural parameters of ZnO tetrapods are determined by the location in the synthesis zone (correlated with the distance from the air inflow window). All samples were characterized by pseudo-three-dimensional morphology of tetrapods. A correlation was found between luminescent properties and photocatalytic activity of tetrapods. The highest photodegradation rates of methylene blue under ultraviolet radiation were demonstrated by ZnO tetrapods grown in the zones closest and farthest from the window (rate constants 54 × 10–3 min–1 and 50 × 10–3 min–1, respectively).

Effect of Nanostructure Morphology and Concentration on the Piezoelectric Performance of Flexible Pressure Sensor based on PVDFTrFE/ Nano-ZnO Composite Thin Film

Background: The development of high-performance piezoelectric pressure sensors with outstanding sensitivity, good linearity, flexibility, durability, and biocompatibility is of great significance for smart robotics, human healthcare devices, smart sensors, and electronic skin. Thus, considerable progress has been achieved in enhancing the piezoelectric property of PVDF-TrFEbased composite pressure sensors by adding various ZnO nanostructures in PVDF-TrFE polymer acting as a nucleating agent and dielectric material. Aims: In this work, flexible pressure sensors with a sandwich structure based on PVDFTrFE/ nano-ZnO composite sensing film were fabricated using a simple spin-coating method and post-annealing process, while electrospinning and high-voltage polarization processes were not adopted. Methods: Poly (vinylidene fluoride-trifluoroethylene) (PVDF-TrFE)/nano-ZnO composite films were prepared via spin coating to fabricate flexible piezoelectric pressure sensors. ZnO nanoparticles (ZnO NPs), tetrapod ZnO (T-ZnO) and ZnO nanorods (ZnO NRs) were used as nano-fillers for piezoelectric PVDF-TrFE, to enhance the beta-crystal ratio as well as the crystallinity of PVDF-TrFE. The structural and surface morphologies of the composite films were investigated using Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). Results: Among three different types of ZnO nanostructures with a concentration range (0-7.5 wt%), the sensor with 0.75 wt% ZnO NRs nanofiller exhibits a maximum output voltage of 1.73 V under an external pressure of 3 N and a maximum sensitivity of 586.3 mV/N at the range of 0-3 N. Further, the sensor can generate a clear piezoelectric voltage under bending and twisting deformation as well as compression and tensile deformation. Conclusion: To summarize, the addition of different concentrations of nano-ZnO can remarkably improve the piezoelectric performance of the composite sensor, and ZnO NRs can achieve better piezoelectric properties of the sensor as compared to ZnO NPs and T-ZnO. In addition, the sensor with 0.75 wt% ZnO NRs as nanofiller has the highest piezoelectric response, which is about 2.4 times that of the pure PVDF-TrFE sensor. It is demonstrated that the sensor has great potential applications in wearable health monitoring systems and mechanical stress measurement electronics.

Characterization and Photocatalytic Properties of ZnO Tetrapods Synthesized by High-Temperature Pyrolysis

Characterization and Photocatalytic Properties of ZnO Tetrapods Synthesized by High-Temperature Pyrolysis

Photoluminescence-based biosensor for the detection of antibodies against SARS-CoV-2 virus proteins by ZnO tetrapod structure integrated within microfluidic system

This paper reports on development of an optical biosensor for the detection of antibodies against SARS-CoV-2 virus proteins in blood serum. ZnO nanotetrapods with high surface area and stable room temperature photoluminescence (PL) were selected as transducers. Structure and optical properties of the ZnO tetrapods have been studied by XRD, SEM and Raman spectroscopy. Crystallinity, dimensions and emission peaks of the ZnO tetrapods were determined. The ZnO tetrapods were fixed on glass chip. Silanization of ZnO tetrapods surface resulted in forming of functional surface groups suitable for the immobilization of bioselective layer. Two types of recombinant proteins (rS and rN) have been used to form bioselective layer on the surface of the ZnO tetrapods. Flow through microfluidic system, integrated with optical system, has been used for the determination of antibodies against SARS-CoV-2 virus proteins present in blood samples. The SARS-CoV-2 probes, prepared in PBS solution, have been injected into the measurement chamber with a constant pumping speed. Steady-state photoluminescence spectra and photoluminescence kinetics have been studied before and after injection of the probes. The biosensor signal has been tested to anti-SARS-CoV-2 antibodies in the range of 0.001 nM–1 nM. Control measurements have been performed with blood serum of healthy person. ZnO-SARS-CoV-2-rS and ZnO-SARS-CoV-2-rN biosensors showed high stability and sensitivity to anti-SARS-CoV-2 antibodies in the range of 0.025–0.5 nM (LOD 0.01 nM) and 0.3–1 nM (LOD 0.3 nM), respectively. Gibbs free energy of interaction between ZnO/SARS-CoV-2-rS and ZnO/SARS-CoV-2-rN bioselective layers with anti-SARS-CoV-2 antibodies showed −35.5 and −21.4 kJ/mol, respectively. Average detection time of biosensor integrated within microfluidic system was 15–20 min. The detection time and pumping speed (50 μL/min) were optimized to make detection faster. The developed system and ZnO-SARS-CoV-2-rS nanostructures have good potential for detection of anti-SARS-CoV-2 antibodies from patient's probes.

Controlling bacterial growth and inactivation using thin film-based surface acoustic waves.

Formation of bacterial films on structural surfaces often leads to severe contamination of medical devices, hospital equipment, implant materials, etc., and antimicrobial resistance of microorganisms has indeed become a global health issue. Therefore, effective therapies for controlling infectious and pathogenic bacteria are urgently needed. Being a promising active method for this purpose, surface acoustic waves (SAWs) have merits such as nanoscale earthquake-like vibration/agitation/radiation, acoustic streaming induced circulations, and localised acoustic heating effect in liquids. However, only a few studies have explored controlling bacterial growth and inactivation behaviour using SAWs. In this study, we proposed utilising piezoelectric thin film-based SAW devices on a silicon substrate for controlling bacterial growth and inactivation with and without using ZnO micro/nanostructures. Effects of SAW powers on bacterial growth for two types of bacteria, i.e., E. coli and S. aureus, were evaluated. Varied concentrations of ZnO tetrapods were also added into the bacterial culture to study their effects and the combined antimicrobial effects along with SAW agitation. Our results showed that when the SAW power was below a threshold (e.g., about 2.55 W in this study), the bacterial growth was apparently enhanced, whereas the further increase of SAW power to a high power caused inactivation of bacteria. Combination of thin film SAWs with ZnO tetrapods led to significantly decreased growth or inactivation for both E. coli and S. aureus, revealing their effectiveness for antimicrobial treatment. Mechanisms and effects of SAW interactions with bacterial solutions and ZnO tetrapods have been systematically discussed.

Gas-Sensing Properties and Mechanisms of 3D Networks Composed of ZnO Tetrapod Micro-Nano Structures at Room Temperature.

Metal oxide semiconductors (MOSs) hold great promise for electronic devices such as gas sensors. The utilization of ZnO as a conductometric gas sensor material can be traced back to its early stages; however, its application has primarily been limited to high-temperature environments. A gas sensor based on highly porous and interconnected 3D networks of ZnO tetrapod (ZnO-T) micro-nano structures was fabricated via an easy chemical vapor deposition (CVD) method. Homemade instruments were utilized to evaluate the gas-sensing of the sample at room temperature. It exhibited good gas-sensing at room temperature, particularly with a response of up to 338.80% toward 1600 ppm ethanol, while also demonstrating remarkable repeatability, stability, and selectivity. Moreover, the unique gas-sensing properties of ZnO-T at room temperature can be reasonably explained by considering the effect of van der Waals forces in physical adsorption and the synergistic effect of carrier concentration and mobility. The aforementioned statement presents an opportunity for the advancement of gas sensors utilizing ZnO at room temperature.

Luminescence and Photocatalytic Properties of ZnO Tetrapods

Luminescence and Photocatalytic Properties of ZnO Tetrapods

Laser additive manufacturing of shape memory biopolymer bone scaffold: 3D conductive network construction and electrically driven mechanism

IntroductionThe electro-actuated shape memory polymer scaffold has gained increasing attentions on the utilization of minimally invasive surgery for bone defect repair, which requires to construct an efficient conductive network to accomplish electrical-to-thermal conversion from conductive fillers to the entire matrix evenly. ObjectivesIn this study, multiwall carbon nanotube (MWCNT) was convective self-assembled on the ZnO tetrapod (t-ZnO) template, where MWCNT was controlled to disperse uniformly and regulated to contact with each other effectively due to the immersion capillary force during the evaporation loss of the convective self-assembly process, leading to an interwoven layer on the t-ZnO surface. MethodsThe prepared t-ZnO@MWCNT assembly was embedded in the poly(L-lactic acid)/thermoplastic polyurethane (PLLA/TPU) scaffold fabricated via selective laser sintering to construct a 3D conductive MWCNT network for improving the electro-actuated shape memory properties. ResultsIt was observed that the interconnected MWCNT formed a 3D conductive network in the matrix without significant aggregation, which boosted the electrical-to-thermal properties of the scaffold, and the scaffold containing t-ZnO@MWCNT assembly possessed better electro-actuated shape memory properties with shape fixity of 98.0% and shape recovery of 98.8%. ConclusionThe scaffold exhibited improved electro-actuated shape memory properties and mechanical properties and the osteogenic inductivity was promoted with the combined effect of t-ZnO and electrical stimulation.

Oxygen Vacancies and Surface Wettability: Key Factors in Activating and Enhancing the Solar Photocatalytic Activity of ZnO Tetrapods.

This paper reports on the high photocatalytic activity of ZnO tetrapods (ZnO-Ts) using visible/solar light and hydrodynamic water flow. It was shown that surface oxygen defects are a key factor in the photocatalytic activity of the ZnO-Ts. The ability to control the surface wettability of the ZnO-Ts and the associated concentration of surface defects was demonstrated. It was demonstrated that the photocatalytic activity during the MB decomposition process under direct and simulated sunlight is essentially identical. This presents excellent prospects for utilizing the material in solar photocatalysis.

Photocatalytic degradation of different types of microplastics by TiOx/ZnO tetrapod photocatalysts

We investigated the use of titania coated ZnO tetrapods for photocatalytic degradation of two common types of microplastics, namely polyethylene (PE) microparticles and polyester (PES) microfibers. We found that the plastics morphology affects the rate of degradation, and that the use of electron scavengers is needed to maintain the reactivity of the photocatalysts over a prolonged period of time. Complete mass loss of PE and PES is achieved under UV illumination for 480 h and 624 h, respectively. In addition to pristine microplastics, the degradation of environmental microplastics sample (consisting primarily of polypropylene) was also demonstrated, though in this case longer degradation time (∼816 h) was needed to achieve complete mass loss of the samples.

Tetrapodal textured Janus textiles for accessible menstrual health

Menstruating individuals without access to adequate hygiene products often improvise with alternatives that pose health risks and limit their participation in society. We describe here a menstrual hygiene product based on low-cost materials, which are integrated onto fabrics to imbue unidirectional permeability. Abody-facing "Janus" fabric top layer comprising ZnO tetrapods spray-coated onto polyester mosquito netting imparts hierarchical texturation, augmenting the micron-scale texturation derived from the weave of the underlying fabric. The asymmetric coating establishes a gradient in wettability, which underpins flash spreading and unidirectional permeability. The hygiene product accommodates a variety of absorptive media, which are sandwiched between the Janus layer and a second outward-facing coated densely woven fabric. An assembled prototype demonstrates outstanding ability to wick saline solutions and a menstrual fluid simulant while outperforming a variety of commercially alternatives. The results demonstrate a versatile menstrual health product that provides a combination of dryness, discretion, washability, and safety.

ZnO tetrapod morphology influence on UV sensing properties.

The aim of this work was to investigate how ZnO tetrapod (ZnO-T) morphology, structure, and surface charge properties (i.e. Debye length) influence their UV sensing properties, shedding light on the underlying photoresponse mechanisms. ZnO-Ts were synthesized and centrifuged to obtain three different fractions with tuned morphology, which were characterized by scanning electron microscopy, transmission electron microscopy, and high-resolution transmission electron microscopy microscopies, x-ray diffraction analysis, Brunauer-Emmett-Teller measurements, FTIR and UV-vis spectroscopies. ZnO-T UV sensors were fabricated and tested comparing among ZnO-T fractions and commercial ZnO nanoparticles. ZnO-T photoresponse was mostly influenced by ZnO-T leg diameter, with the optimal value close to the double Debye length. We also demonstrated how fractionating ZnO-Ts for morphology optimization can increased the responsivity by 2 orders of magnitude. Moreover, ZnO-T showed 3 orders of magnitude higher responsivity compared to commercial ZnO nanopowder. These results are beneficial for the engineering of efficient UV sensors and contribute to a deeper understanding the overall mechanism governing UV photoresponse.

Photocatalytic activity of ZnO nanomaterials with different morphologies

The influence of ZnO nanomaterial morphologies on their photocatalytic activity was studied. The ZnO nanobelts and the network of hexagonal disks were grown by pyrolysis in ammonium chloride. ZnO tetrapods were produced by plasma-assisted technology. The nanobelts and tetrapod arms were growing along the c-axis. The sidewalls of nanobelts comprise (21�1�0) and (011�0) plane, while the needle-shape arms of tetrapods are known to consist of altering {011�0} and semi-polar {101�1} facets. The hexagonal ZnO disks have exposed mainly (+0001) facets with the highest surface energy. They showed the highest photocatalytic activity for the degradation of methylene blue, dissolved in water to a concentration of 100 mg/L.

Surface Conversion of ZnO Tetrapods Produces Pinhole-Free ZIF-8 Layers for Selective and Sensitive H2 Sensing Even in Pure Methane.

As the necessary transition to a supply of renewable energy moves forward rapidly, hydrogen (H2) becomes increasingly important as a green chemical energy carrier. The manifold applications associated with the use of hydrogen in the energy sector require sensor materials that can efficiently detect H2 in small quantities and in gas mixtures. As a possible candidate, we here present a metal-organic framework (MOF, namely ZIF-8) functionalized metal-oxide gas sensor (MOS, namely ZnO). The gas sensor is based on single-crystalline tetrapodal ZnO (t-ZnO) microparticles, which are coated with a thin layer of ZIF-8 ([Zn(C4H5N2)2]) by a ZnO conversion reaction to obtain t-ZnO@ZIF-8 (core@shell) composites. The vapor-phase synthesis enables ZIF-8 thickness control as shown by powder X-ray diffraction, thermogravimetric analysis, and N2 sorption measurements. Gas-sensing measurements of a single microrod of t-ZnO@ZIF-8 composite demonstrate the synergistic benefits of both MOS sensors and MOFs, resulting in an outstanding high selectivity, sensitivity (S ≅ 546), and response times (1-2 s) to 100 ppm H2 in the air at a low operation temperature of 100 °C. Under these conditions, no response to acetone, n-butanol, methane, ethanol, ammonia, 2-propanol, and carbon dioxide was observed. Thereby, the sensor is able to reliably detect H2 in mixtures with air and even methane, with the latter being highly important for determining the H2 dilution level in natural gas pipelines, which is of great importance to the energy sector.

Highly-hydrophobic, transparent, and durable coatings based on ZnO tetrapods with diamond-like carbon nanocomposite

This study investigates the wettability of ZnO tetrapod (ZnO-T) coatings in relation to surface morphology and protective diamond-like carbon nanocomposites with SiOx (DLC:SiOx) film parameters. Randomly distributed ZnO-Ts with different leg lengths were observed to have varying degrees of wettability, which also changed keeping samples in the dark at room temperature. DLC:SiOx films significantly increase the hydrophobicity of ZnO-T coatings, and their thickness influences the surface roughness and hydrophobicity of the coating, moreover DLC:SiOx films show protection not only from the abrasion but also passivate the ZnO-T coatings from light-induced effects. The results indicate that the largest size ZnO-T fraction with a 40 nm thickness of DLC:SiOx film can provide the best hydrophobicity represented by a water contact angle of 148°, while the smallest ZnO-T fraction with a 120 nm thickness of DLC:SiOx film can provide better mechanical durability. We expect that the detailed analysis of ZnO-T coatings with protective DLC:SiOx films conducted in this study will be advantageous for other nanostructures with protective coatings application in wettability control.

ZnO UV sensor photoresponse enhancement by coating method optimization

Modern high-performance photodetector research is driven by the need to simultaneously improve multiple parameters, but also fit the decreasing size of electronics and maintain low production price. Here, we demonstrated how our synthesized ZnO tetrapod (ZnO-T) nanostructure was deposited on electrodes with variating gap by four coating methods including drop casting, microdrop casting, spray coating and slot-die coating with the same thickness. Optimizing the inter-electrode gap and coating method the record IUV/IDark ratio per unit area value of 8.73 × 106 was obtained. The fastest rise time 0.78 s and fastest decay time 0.94 s were obtained by slot-die coated sensors. High photoresponse of ZnO-Ts, the inter-electrode gap size influences formation of ZnO-T microstructure during coating process and morphology influence on photoresponse was explained. We demonstrate that even with the same optimized ZnO-T nanostructures photoresponse can be improved by 2 orders of magnitude. Our work shows the importance of coating morphology and inter-electrode gap optimization.

Electron paramagnetic resonance

We have studied literature from investigation of the impact of Mechanothermal effects in the creation of defect structures in dispersed systems after prolonged mechanical treatment of ZnO powders. This work illustrates some potential applications of electron paramagnetic resonance. EPR application beginning of a variety of paramagnetic processes is based on the knowledge that this centre happens when some materials are mechanically treated. These facilities can act as EPR sondes of various thermal processes that appear when systems are being mechanically treated consisting of ZnO.Zn was evaporated in air, dry and humid argon flow, and dry and humid nitrogen flow to create Zno tetrapod nanostructures. SEM, X-ray diffraction, photoluminescence, photoluminescence excitation (PLE) spectroscopy (at various temperatures), and electron paramagnetic resonance (EPR) spectroscopy at −160 ℃ and room temperature have all been used to explore the characteristics. It is discovered that the fabrication conditions have a considerable impact on the acquired EPR and PL spectra. while some of the samples exhibit a g = 1.96 EPR signal. We used microwave processing to create and mix ZnO nanoparticles (ZnO-NPs) with various amounts of graphene oxide (GO) (10 %, 20 %, and 30 %).The process delivered evenly distributed ZnO-NPs onto and between the rGO layers.(GZCs). The UV–vis absorption, PL emission, defect states of the ZnO, EPR signals, photo-electrochemical reaction, and charge transfer properties were all influenced by the annealing temperature and graphene oxide content. The GZCs' HRTEM microscopy pictures revealed interpenetrating structures and vacancy flaws that were easily seen. The findings showed that following hybridization with GO, the defect sites (Zn interstitials, oxygen vacancy, ionised oxygen vacancy, and oxygen interstitials) greatly decreased. The GZC-10photo-conversion 10 %'s efficiency(ŋ= 13.1 × 10-3%) We have studied literature from Ref.[1]which show that.

ZnO Tetrapods for Label-Free Optical Biosensing: Physicochemical Characterization and Functionalization Strategies

In this study, we fabricated three different ZnO tetrapodal nanostructures (ZnO-Ts) by a combustion process and studied their physicochemical properties by different techniques to evaluate their potentiality for label-free biosensing purposes. Then, we explored the chemical reactivity of ZnO-Ts by quantifying the available functional hydroxyl groups (-OH) on the transducer surface necessary for biosensor development. The best ZnO-T sample was chemically modified and bioconjugated with biotin as a model bioprobe by a multi-step procedure based on silanization and carbodiimide chemistry. The results demonstrated that the ZnO-Ts could be easily and efficiently biomodified, and sensing experiments based on the streptavidin target detection confirmed these structures' suitability for biosensing applications.

Building of soft-hard compound brush in porous PVA/NH2@TAtZnO plural gel and the high-efficiency anti-interference removal on Pb(II)

In order to promote the heavy metal ions removal of porous gel adsorbent and protect the adsorbent from other pollutants in wastewater, the tetrapod ZnO whiskers (tZnO) modified by amino-chain brush was introduced into the polyvinyl alcohol (PVA) matrix to prepare the PVA/NH2@TAtZnO composites with brush structure for toxic Pb(II) removal. The adsorption property, adsorption process and adsorption mechanism were studied by adsorption isotherms, adsorption kinetics, adsorption thermodynamics, SEM-EDS analysis and XPS analysis. And the anti-interference ability and anti-interference mechanism were researched by SEM-EDS analysis and XPS analysis. It was found that the PVA/NH2@TAtZnO composites displayed a soft-hard compound pore-brush structure and showed a good selective adsorption on Pb(II). The research of isotherms and kinetics indicated that the adsorption process was fitted well to Langmuir model and pseudo-second-order model, respectively, and the research of thermodynamics revealed the endothermic nature. The adsorption mechanism was inferred as the combination of predominant chemisorption and subsidiary physisorption. Comparing with the neat PVA matrix, the PVA/NH2@TAtZnO composites displayed a good anti-interference property on Pb(II) adsorption and showed an alleviative clogging pore-canal structure in the wastewater with SiO2 NPs or PAC flocculants. The anti-interference intensity ΔQ and anti-interference factor χ were proposed to reflect the anti-interference ability of this adsorbent which was promoted with the increasing amino brush length or density. By the analysis of SEM-EDS and XPS, the anti-interference mechanism was explored as the steric-hinerance effect of tZnO hard brush to suspended SiO2 NPs pollutant and the coordination effect of functional amino soft brush to soluble PAC pollutant. Besides, the prepared PVA/NH2@TAtZnO adsorbent possessed a good reusability under multiple adsorption-desorption processes and also presented a well applicability in real water matrix. The research indicated the huge potential of prepared PVA/NH2@TAtZnO adsorbent in heavy metal ions removal.

Влияние морфологических и структурных параметров тетраподов ZnO на их активность в реакции фотокаталитической деградации ципрофлоксацина

The influence of morphological and structural parameters of microdimensional tetrapods ZnO on their activity in the reaction of photocatalytic degradation of ciprofloxacin under the influence of UV light has been studied. The greatest activity (velocity constant 25.5 · 10-3 min-1) was demonstrated by unalloyed ZnO tetrapods obtained in the presence of Au in the initial charge, which had the smallest geometric parameters. The photocatalytic activity of tetrapods is explained by the highly defective structure of their near-surface layers. Photoactive microsize tetrapods ZnO, synthesized by the carbothermal method, can be used in the mineralization of toxic organic compounds.