Yttrium Aluminum Garnet Research Articles

Pilot Study to Demonstrate Improvement in Skin Tone and Texture by Treatment with a 1064 nm Q-Switched Neodymium-Doped Yttrium Aluminum Garnet Laser.

The 1064 nm Q-switched neodymium-doped yttrium aluminum garnet (QS Nd:YAG) laser was developed to treat unwanted pigmentation in the skin such as lentigines caused by photoaging, and tattoos from dye/ink insertion. This laser has also been used for non-ablative epidermal rejuvenation (skin toning). To evaluate changes in skin tone, skin texture and overall improvement after a series of treatments with the QS Nd:YAG laser. Participants received seven full-face treatments with M22 or Stellar M22, a 1064 nm QS Nd:YAG laser, at 2-week intervals. The investigators and participants evaluated the improvement in skin tone and texture at 1, 3 and 6 months after the last treatment. Patient satisfaction, patient discomfort, downtime and adverse events were recorded. Histological changes in the treated area were also evaluated. Thirteen women with a median age of 45 years (range, 34-61 years) were included in the study. The majority of the participants (53.9%) had skin type VI. One month after the last treatment session, 38% of participants reported good to very good improvement. This value increased to 100% participant improvement at both the 3-month and 6-month follow-up visits. The reduction in melanin index and the histological analysis demonstrated that the laser procedure contributed to a reduction in epidermal melanin content. Treatments were not associated with high levels of pain or discomfort. The most common immediate post-treatment response was erythema and edema. Most participants were satisfied with the resulting treatment outcome. Skin treatment with the 1064 nm QS Nd:YAG laser module on the M22 and Stellar M22 devices, using a large spot size, low fluence, moderately high repetition rate, improves skin tone and texture in patients with skin types II-VI.

Novel 532-nm Q-switched Nd: YAG laser for the treatment of melasma and rejuvenation: a prospective, randomized controlled comparison with 1,064-nm Q-switched Nd: YAG laser.

Melasma is a common pigmentary and photoaging disorder. Although various treatments, including 1,064-nm Q-switched neodymium-doped yttrium aluminum garnet (QS-Nd: YAG) laser toning, are available for melasma, results are often unsatisfactory. We aimed to determine the efficacy and safety of 532-nm QS-Nd: YAG laser (shortwave toning) in patients with melasma and facial rejuvenation. Fifty-two patients were recruited to receive either 1,064-nm QS-Nd: YAG laser or 532-nm QS-Nd: YAG laser every 2 weeks for 8 sessions and a 2-month follow-up visit in a randomized controlled double-blinded study. The primary outcome measure was the Melasma Area and Severity Index (MASI) score. Dermoscope and high-frequency ultrasound (HFUS) were used to assess the improvement of melasma and photoaging. 532-nm QS-Nd: YAG laser achieved significantly higher improvement in the MASI score (P = 0.000). The Dermoscopic melasma score (DMS) displayed significant change and confirmed the improvement. HFUS showed a significant decrease in the thickness of the subepidermal low-echogenic band (SLEB) and increases in dermal thickness and dermal density in both groups (P = 0.000 for all). The rate of very satisfied responses was significantly higher in the 532-nm laser group (P = 0.001). There was no significant difference in the visual analog scale pain assessment score (P = 0.248) and recurrence rate (P = 0.734) between the two groups. 532-nm QS-Nd: YAG laser (shortwave toning) proved to be an effective and safe treatment for melasma and rejuvenation. Shortwave toning was significantly better for pigmentation clearance, while 1,064-nm laser showed better improvement in skin rejuvenation.

The Efficacy of Different Laser Applications on Dentin Sealing in Preventing Discoloration Induced by Mineral Trioxide Aggregate.

The aim of this in vitro study was to evaluate the effect of the pre-application of a dentin-bonding agent and the application of different lasers on the prevention of tooth discoloration caused by mineral trioxide aggregate (MTA) in the presence of blood. Sixty extracted human anterior teeth were selected, with root lengths standardized to 10 mm and root canals shaped using Gates-Glidden drills #3 to #5. The samples were divided into six groups (n = 10): Group 1 with no surface treatment and Groups 2 to 6 with Optibond universal adhesive and Neodymium yttrium aluminum garnet (Nd:YAG), Erbium yttrium aluminum garnet (Er:YAG), Erbium-chromium-yttrium-scandium-gallium-garnet (Er:Cr:YSGG), and diode laser applications, respectively. Root canals were filled with fresh human blood, and ProRoot MTA and a collagen barrier were then placed. Color changes were measured with a spectrophotometer at 0, 7, 30, 90, and 180 days post MTA placement. Color differences (∆E) were analyzed using a two-factor mixed-design ANOVA with the Sidak method (p = 0.05). All treatment groups exhibited discoloration above the acceptability threshold. Although all treatment approaches exhibited less color change compared to the control group (p < 0.05), there was no significant difference among them in terms of preventing color change (p > 0.05). It was determined that none of the methods could guarantee 100% prevention of discoloration caused by MTA-blood contact.

Efficacy and safety of bipolar fractional radiofrequency vs. 2940-nm Er:YAG ablative fractional laser in striae distensae treatment: A split abdomen study.

Striae distensae (SD) is a challenging cosmetic condition. Ablative fractional laser (AFL) is an effective method for treating SD. Recently, fractional radiofrequency (FRF) has been shown to be a promising treatment for SD; however, few studies have shown the differences between FRF and AFL in the treatment of SD. This study aimed to evaluate and compare the clinical efficacy and safety of bipolar FRF with 2940-nm erbium yttrium aluminum garnet (Er:YAG) AFL in the treatment of SD. Twenty volunteers with abdominal SD were enrolled in this study. One half of the abdomen was treated with 2940-nm Er:YAG AFL, whereas the other half was treated with bipolar FRF, with three sessions at 4-week intervals. Photographic evaluations of clinical improvement were conducted by two independent investigators before and after treatment, and the patients provided self-assessments. Two participants underwent three punch biopsies, one before treatment and two obtained from bilateral representative skin lesions on the abdomen 3 months following the final treatment. Clinical improvements were observed in SD on both sides of the abdomen after the two treatments. Post-treatment skin biopsies revealed increased thickness in the epidermis and dermis, and higher collagen and elastin density compared to those at the baseline. No statistically significant differences were observed in the clinical outcomes between the two treatment approaches. The efficacy and safety of bipolar FRF treatment are comparable to those of 2940-nm Er:YAG AFL treatment, providing an alternative and effective treatment for SD.

Direct observation and measurement of circumlental space and its relation to anterior chamber angle characteristics in iridotomized phakic eyes with primary angle closure disease

Primary angle closure disease (PACD) is a major cause of blindness worldwide. It has a high prevalence in East Asia, especially in China, which leads to a higher incidence of blindness than open-angle glaucoma. The aim of this study was to directly observe the circumlental space (CLS) in laser peripheral iridotomized eyes with PACD and to determine whether this structure plays a role in the pathogenesis of PACD. Fifty eyes of 50 patients with PACD, who had received laser peripheral iridotomy performed with neodymium:yttrium–aluminum-garnet were recruited from glaucoma clinics from March 2021 to May 2022, including 17 primary angle closure suspect (PACS), 16 primary angle closure (PAC) and 17 primary angle closure glaucoma (PACG). They were classified into two groups based on whether the ciliary process and the crystalline lens equator were in contact using slit-lamp photograph: the attached group and the unattached group. The demographic, clinical characteristics and anterior segment parameters measured from ultrasound biomicroscopy were compared between the attached group and the unattached group. Thirty-three eyes were assigned to the attached group and 17 eyes belonged to the unattached group. In the unattached group, the mean CLS was 0.10 ± 0.07 mm. No significant differences were identified between the different diagnosis groups in age, sex, best-corrected visual acuity, intraocular pressure, white-to-white, axial length, central corneal thickness, anterior chamber depth, flat keratometry, steep keratometry or iridotomy diameter (p > 0.05). The unattached group had shorter trabecular-ciliary process distance (p = 0.021) and larger ciliary process area (p = 0.001) compared with the attached group. Small CLS and its potential effect (partial ciliary block) might be considered as one of the mechanisms of PACD.

Novel lanthanide-doped Y3-xNaxAl5-yVyO12 garnets: Synthesis, structural and optical properties

In this study the novel garnet-type Y2.47Na0.5Ln0.03Al5O12, Y2.97Ln0.03Al4.95V0.05O12, Y2.92Na0.05Ln0.03Al4.9833V0.0167O12 (Ln = Ce3+, Tb3+, Eu3+) phosphors were successfully synthesized by the sol-gel method for the first time. The structural, morphological and optical properties were characterized by using multiple characterization techniques. The XRD and FTIR results confirmed that all obtained phosphors are monophasic yttrium aluminium garnet compounds, i.e. the doping of Ce3+, Tb3+, Eu3+, Na+, V5+ ions does not induce any impurity phases, indicating the successful incorporation of these dopants into the YAG host. The formation of novel garnets was probed using 27Al, 51V, 23Na MAS NMR techniques. SEM micrographs revealed that almost in all cases, the surface of the obtained luminophores is porous and consists of homogeneously distributed irregular sphere-like shape particles, which tend to form larger agglomerates. The optical properties of obtained compounds were also investigated by recording their excitation and emission spectra and calculating the colour coordinates in the CIE 1931 colour space.

Effects of Nd: YAG LASER irradiation and O2 plasma on the adhesive performance of poly-ether-ether-ketone (PEEK)

PurposeTo evaluate the effects of neodymium-doped yttrium aluminum garnet (Nd: YAG) LASER irradiation and oxygen (O2) plasma on the adhesive performance of polyether ether ketone (PEEK) and resin adhesive. MethodsNd: YAG LASERs of varying powers and O2 plasma for different durations were used to modify PEEK. A total of 168 PEEK specimens were randomly divided into seven groups (n = 24/group): (A) Control group: untreated PEEK, (B) L0.75 group: PEEK modified with 0.75 W Nd: YAG LASER, (C) L1 group: PEEK modified with 1.0 W Nd: YAG LASER, (D) L1.25 group: PEEK modified with 1.25 W Nd: YAG LASER, (E) P15 group: PEEK modified with 15 min of O2 plasma, (F) P25 group: PEEK modified with 25 min of O2 plasma, and (G) P35 group: PEEK modified with 35 min of O2 plasma. The surface characteristics of the materials were comprehensively analyzed using a scanning electron microscope (SEM), profilometer, energy-dispersive spectrometer (EDS), and contact angle tester. The adhesive specimens were bonded with Variolink N resin adhesive in all groups and each group was further divided into two subgroups (n = 12/group): (a) water storage for 56 h at 37 °C and (b) thermal cycling 5000 times. Shear bond strength (SBS) was tested using a universal testing machine, and the fracture modes were observed using an automated chemiluminescence analysis system to assess the effects of Nd: YAG LASER and O2 plasma on the bond strength of PEEK to resin adhesive. ResultsBoth Nd: YAG LASER and O2 plasma treatments altered the surface characteristics of PEEK and significantly increased the SBS between PEEK and Variolink N resin adhesive. The L0.75 group (Nd: YAG LASER) and the P35 group (O2 plasma) achieved the highest SBS, respectively. Furthermore, the SBS of the L0.75 group was higher than that of the P35 group. Following thermal cycling, SBS values decreased compared to the water storage subgroups. The fracture modes of the specimens in each group were predominantly interfacial and mixed, with no cohesive fractures observed. ConclusionsNd: YAG LASER irradiation and O2 plasma treatments can improve the SBS between PEEK and resin adhesive, with the 0.75 W Nd: YAG LASER being the preferred treatment method.

Laser Technology Advancements in the Treatment of Benign Prostatic Hypertrophy.

Lasers have had a significant impact on the treatment of benign prostatic hypertrophy. This article attempts to distill the advancements in laser technology for the treatment of benign prostatic hypertrophy (BPH) into key and understandable points to help make this topic more accessible to urologists. The holmium:yttrium-aluminum-garnet (YAG) laser, one of the most significant lasers in the field of urology, has recently been improved with pulse modulating technology (Moses™ technology). New thulium:YAG technology allows both pulsed and continuous wave modes. The thulium fiber laser is one of the newer lasers to come to market and has been shown to have effective and safe outcomes. GreenLight™ lasers are predominantly used in photovaporization procedures and have also been studied extensively, although less in recent years. The modern urologist is fortunate to have many high-quality lasers and a wide variety of surgical techniques to choose from when treating BPH. Understanding the basic laser principles and applications will help urologists to select the best treatment options for their patients with BPH.

Er:YAG Laser Alleviates Inflammaging in Diabetes-Associated Periodontitis via Activation CTBP1-AS2/miR-155/SIRT1 Axis.

Periodontitis is a significant health concern for individuals with diabetes mellitus (DM), characterized by inflammation and periodontium loss. Hyperglycaemia in DM exacerbates susceptibility to periodontitis by inducing inflammaging in the host immune system. The use of erbium-doped yttrium-aluminum-garnet laser (ErL) in periodontitis treatment has gained attention, but its impact on diabetic-associated periodontitis (DP) and underlying mechanisms remain unclear. In this study, we simulated DP by exposing human periodontal ligament fibroblasts (PDLFs) to advanced glycation end products (AGEs) and lipopolysaccharides from P. gingivalis (Pg-LPS). Subsequently, we evaluated the impact of ErL on the cells' wound healing and assessed their inflammaging markers. ErL treatment promoted wound healing and suppressed inflammaging activities, including cell senescence, IL-6 secretion, and p65 phosphorylation. Moreover, the laser-targeted cells were observed to have upregulated expression of CTBP1-AS2, which, when overexpressed, enhanced wound healing ability and repressed inflammaging. Moreover, bioinformatic analysis revealed that CTBP1-AS2 acted as a sponge for miR155 and upregulated SIRT1. In conclusion, ErL demonstrated the ability to improve wound healing and mitigate inflammaging in diabetic periodontal tissue through the CTBP1-AS2/miR-155/SIRT1 axis. Targeting this axis could represent a promising therapeutic approach for preventing periodontitis in individuals with DM.

Effects of Various Laser Treatments on Surface Characterization and Repair Bond Strength of Zirconia-Reinforced Lithium Silicate Ceramics.

To evaluate the effects of two different lasers and their use in combination with hydrofluoric acid (HF) etching on the surface roughness of zirconia-reinforced lithium silicate (ZLS) ceramics and their shear bond strength (SBS) to composite resin. The five study groups were as follows: (1) Group H = HF etching; (2) Group N = Nd:YAG (neodymium: yttrium-aluminum-garnet) laser; (3) Group NH = Nd:YAG laser + HF gel; (4) Group E = Er:YAG (erbium: yttrium-aluminum-garnet) laser; and (5) Group EH = Er:YAG laser + HF gel. Surface roughness was assessed using a noncontact profilometer, and SBS tests were conducted with a universal testing machine. The mean SBS values were 16.23 ± 1.77 MPa for Group H, 17.1 ± 1.65 MPa for Group N, 16.65 ± 1.11 MPa for Group NH, 8.08 ± 1.12 MPa for Group E, and 11.58 ± 0.82 MPa for Group EH. There were significant differences between groups E and EH (P < .001) but no significant differences (P > .05) among the other groups. Clinicians may prefer Nd:YAG laser or the combination of Nd:YAG and HF to intraorally repair fractured areas.

The spectrally resolved photoluminescence decay in YAG:Er, ZnO and SiO2 crystals

We present an optical setup for measuring spectrally resolved photoluminescence (PL) mean decay time using conventional UV LED with sinusoidal excitation and a phase shift method. The phase sensitive detection was applied on the Er-doped yttrium aluminium garnet single crystal (YAG:Er, grown by the micro-pulling-down method) and hydrothermally grown zinc oxide micro-crystallites (ZnO). Commercial ZnO and silicon oxide (SiO2) microcrystalline powders were measured for comparison. SiO2 powder was annealed in O2 plasma at 500 °C for cleaning. While YAG:Er shows well resolved greenish PL peaks with mean decay time about 15 μs related to the Stark splitting of Er3+ (4f11) states and ZnO micro-powder broad reddish PL with similar PL decay time, the plasma treated SiO2 powder shows weak bluish defect-related PL with significantly faster mean decay times below 100 ns.

Editorial letter to: Incidence of Ureteric Strictures Following Ureteroscopic Laser Lithotripsy: Holmium: YAG Versus Thulium Fiber Laser.

Dear Editor, The original paper by Ahmad Para S et al1 analyzed the incidence of ureteral strictures following holmium: yttrium aluminum garnet (Ho:YAG) and thulium fiber laser (TFL) endocorporeal laser lithotripsy (ELL) for ureteral stones. The authors should be commended for their work because this is the first prospective randomized controlled trial comparing the ureteric stricture rates between these 2 laser technologies for ELL. This study concluded that the TFL had a higher incidence of ureteral strictures than the Ho: YAG laser. Our editorial letter aims to clarify and highlight some key points.

Narrow‐linewidth injection‐locked Ho:YAG laser by using thulium‐doped fiber laser as pumping source

AbstractWe demonstrated a narrow‐linewidth Ho:yttrium aluminum garnet (YAG) injection‐locked laser by using a 1908 nm thulium‐doped fiber laser as a pumping source to generate 2.09 μm single‐frequency pulses. A compact single‐longitudinal‐mode nonplanar ring oscillator (NPRO) based on Ho:YAG material with a beam quality factor of 1.01 at the central wavelength of 2090.91 nm was considered as the seed source. In the experiment, the pulse energy of 3.6 mJ with a pulse width of 161.6 ns from single‐frequency Ho laser was achieved at a pulse repetition frequency (PRF) of 100 Hz. The linewidth of the single‐frequency pulse spectrum monitored through the heterodyne method was approximately 1.9 MHz at the lowest Ho laser energy.

Material Analysis of Explanted Calcified Silicone Intraocular Lenses in Association with Asteroid Hyalosis.

The aim of this study was to analyze posterior surface opacification in explanted silicone intraocular lenses (IOLs) with clinicopathologic correlation to asteroid hyalosis. In a laboratory setup, 12 explanted silicone IOLs underwent laboratory analyses, including light microscopy, scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy for elemental composition (EDX). Relevant clinical data were obtained for each case, including gender, age at IOL implantation, dates of implantation and explantation, as well as history of neodymium-dopped yttrium aluminum garnet (Nd:YAG) laser treatments or other opacification removal attempts. High-resolution optical coherence tomography (OCT) images were obtained in vitro with an anterior segment OCT device (Anterion, Heidelberg Engineering, Heidelberg, Germany). Calcification located at the posterior optic surface of each lens was identified through SEM and EDX analyses, revealing deposits composed of hydroxyapatite. In all cases, IOL polishing using Nd:YAG laser had been attempted prior to IOL exchange. The clinical functional data showed that this type of IOL opacity led to increase in straylight and subjective symptoms of glare. Silicone IOLs can develop posterior surface calcification in eyes with asteroid hyalosis. There are mechanical techniques of cleaning the IOL surface but in many cases, IOL explantation is the only sustainable way to reduce the patients' straylight levels and glare symptoms. Due to the risk of posterior surface calcification, silicone IOL implantation should be avoided in eyes with asteroid hyalosis.

Are there sex-based disparities in cataract surgery?

To investigate sex-based differences in the occurrence of intra-operative and post-operative complications and associated visual outcomes following cataract surgery. This was a retrospective study of patients who had phacoemulsification cataract surgery at the University of Colorado School of Medicine. Data collected included the patient's health history, ocular comorbidities, operative and post-operative complications, and the post-operative best corrected visual acuity (BCVA). The data were analyzed using univariate and multivariable logistic regression with generalized estimating equations to account for the correlation of some patients having two eyes included in the study. A total of 11 977 eyes from 7253 patients were included in the study. Ocular comorbidities differed by sex, with males having significantly higher percentages of traumatic cataracts (males 0.7% vs females 0.1%), prior ocular surgery (6.7% vs 5.5%), and mature cataracts (2.8% vs 1.9%). Conversely, females had significantly higher rates of pseudoexfoliation (2.0% vs 3.2%). In unadjusted analysis, males had higher rates of posterior capsular rupture (0.8% vs 0.4%) and vitreous loss (1.0% vs 0.6%), but this difference was not significant after adjustment for confounders. Males had a significantly increased risk of post-operative retinal detachment, but in multivariable analysis this was no longer significant. Males were significantly less likely to undergo post-operative neodymium-doped yttrium aluminum garnet (Nd:YAG) laser capsulotomy for posterior capsule opacification (OR=0.8, 95%CI=0.7-0.9, P=0.0005). The BCVA was slightly worse for males pre-operatively; but post-operatively, both sexes exhibited similar visual acuity of Snellen equivalent 20/25. The study finds that in a cohort of patients presenting for cataract surgery, sex differences exist in pre-operative comorbidities and surgical characteristics that contribute to higher rates of some complications for males. However, observed surgical complication rates exhibit almost no difference by sex after adjusting for pre-operative differences and post-operative BCVA is similar between sexes.

Prediction of quality characteristics of micro-channels by deep learning algorithm during laser transmission ablation of PMMA

Underwater laser transmission micro-channelling of thick transparent polymethyl methacrylate (PMMA) using a neodymium-doped yttrium aluminium garnet (Nd: YAG) laser is the focus of this study. Experiments are conducted to determine the effect of three significant variables, namely pulse frequency, lamp current, and cutting speed, on heat-affected zone (HAZ) width, cut depth, and kerf width. Experiments are designed systematically utilising the full factorial design method. The purpose of constructing empirical models, specifically non-linear ones, is to establish and clarify the relationship between control factors and corresponding responses. A feed forward backpropagation neural network (FF-BPNN) is employed for predicting the measured response. Additionally, an assessment is made between the FF-BPNN results and the values predicted by the model. On the basis of the anticipated results, it can be concluded that the FF-BPNN model is preferable in predicting both the depth of cut and kerf width. In contrast, when specifically contemplating the measurement of HAZ width, the application of a non-linear model is more advantageous. As a measure of accuracy, the mean absolute error is computed for both the feedforward backpropagation neural network (FF-BPNN) and the nonlinear modelling technique.

Dodecahedron lattice of rattling phenomenon, and microwave dielectric properties of yttrium aluminum garnet ceramics and its application verification for Wifi6E/7 patch and 6G resonant antennas

In garnet phase ceramics Y2.9M0.1Al4.9Si0.1O12 (M = Mg2+, Co2+, Zn2+, Mn2+, Ca2+, Sr2+, Ba2+), rattling effects occur when M = Mg2+, Co2+, Zn2+, Mn2+ ions with smaller ionic radius (<1Å) occupy the dodecahedron lattice lattices. This results in an abnormally high dielectric constant, in contrast to the larger ionic radius (>1 Å) of M = Ca2+, Sr2+ and Ba2+, which deviate from the theoretical values calculated using the Clausius-Mosotti formula according to each ion’s polarizability. The optimal microwave dielectric properties for Y2.9Mg0.1Al4.9Si0.1O12 was obtained by sintering at 1575 °C for 5 h (Q×f = 51,382 GHz, εr = 9.74, and τf = −30.12 ppm/°C). Additionally, a thermal stable Y2.9Mg0.1Al4.9Si0.1O12-6 wt%TiO2 composite ceramic was developed. Based on this composite, a Wifi6E/7 patch antenna operating at 6.3 GHz and a millimeter-wave resonant antenna functioning at 27.1 GHz were designed and validated. This indicates the potential application prospects of garnet ceramics in 5G/6G radio communication technologies.

Analysis of aerosol generation during Er:YAG laser-assisted caries treatment: A randomized clinical trial.

Maintaining biosafety in dental practice involves the effective elimination of aerosols produced during dental treatment. To assess the quantity of aerosols and aerobic bacteria in the air during the treatment of caries. The study involved 60 patients with a total of 60 molar teeth (n = 60) in the mandible who were divided into 2 groups based on caries treatment method. Group 1 (G1, n = 30) received treatment with a conventional dental turbine (W&H Synea TA-98LC; W&H, Burmoos, Austria), while group 2 (G2, n = 30) underwent treatment with an Er:YAG (erbium-doped yttrium aluminium garnet) laser (LightWalker, Fotona, Slovenia). Measurements of aerosol particles between 0.3 Ęm and 10.0 Ęm near the operatorfs mouth were taken using the PC200 laser particle counter (Trotec GmbH, Schwerin, Germany). The number of aerobic bacteria in the air was determined using 60 Petri plates with a microbiological medium (Columbia agar with 5% sheep blood) and the sedimentation method. A control group (G3) was established to measure initial aerosol levels and initial total number of bacteria colony-forming units (CFUs) before each treatment. In G1 (dental turbine), the median value of aerosol particles was 57,021 (42,564.67,568), while in G2 (Er:YAG laser), it was significantly lower at 33,318 (28,463.35,484) (p < 0.001). The median total bacteria count per cubic meter of air in G1 (conventional dental turbine + high volume evacuator (HVE)), G2 (Er:YAG laser + HVE) and G3 (control group before caries treatment) were 734 (420.988), 158 (96.288) and 48 (32.74), respectively, with a statistically significant difference between the groups (p < 0.001). The use of Er:YAG laser during caries treatment resulted in a 41.6% reduction in aerosol amounts and a 78.5% decrease in the total bacterial count (TBC) compared to treatment with a dental turbine.

Effects of the excitation wavelength and temperature on the zero-phonon emission lineofCr:YAG.

In this work, a detailed study was conducted of the temperature and excitation wavelength-dependent photoluminescence (PL) spectra of the chromium-doped yttrium aluminum garnet (Cr:YAG) transparent ceramic. Focusing on the two sets of zero-phonon lines (ZPLs) of the 2 E→4 A 2 transition in this material, the PL spectra are discovered to evolve significantly with respect to temperature and be highly dependent on the excitation wavelength. Compared to the continuous variation behavior with temperature, an increase in the excitation wavelength leads to a blueshift of the peak position within the regions of 450nm to 465nm, 465nm to 490nm, and 490nm to 500nm, and a sharp change in the PL position at the excitation wavelengths of 465nm and 490nm. The electron-phonon coupling (EPC) effect is believed to be more sensitive to the excitation wavelength. Different excitation wavelengths involve different electronic levels participating in the light emission processes, which explains the evolution behavior of the PL peak position with respect to the excitation wavelength. Moreover, the emergence of weak peaks next to the ZPLs at particular temperatures and excitation wavelengths is also observed. This work compares the influence of the temperature and excitation wavelength to the PL properties of the Cr:YAG transparent ceramic, which promotes an advanced understanding of the luminescence behavior of the Cr:YAG transparent ceramics.

Simultaneous label-free autofluorescence multi-harmonic microscopy driven by the supercontinuum generated from a bulk nonlinear crystal.

Nonlinear microscopy encompasses several imaging techniques that leverage laser technology to probe intrinsic molecules of biological specimens. These native molecules produce optical fingerprints that allow nonlinear microscopes to reveal the chemical composition and structure of cells and tissues in a label-free and non-destructive fashion, information that enables a plethora of applications, e.g., real-time digital histopathology or image-guided surgery. Because state-of-the-art lasers exhibit either a limited bandwidth or reduced wavelength tunability, nonlinear microscopes lack the spectral support to probe different biomolecules simultaneously, thus losing analytical potential. Therefore, a conventional nonlinear microscope requires multiple or tunable lasers to individually excite endogenous molecules, increasing both the cost and complexity of the system. A solution to this problem is supercontinuum generation, a nonlinear optical phenomenon that supplies broadband femtosecond radiation, granting a wide spectrum for concurrent molecular excitation. This study introduces a source for nonlinear multiphoton microscopy based on the supercontinuum generation from a yttrium aluminum garnet (YAG) crystal, an approach that allows simultaneous label-free autofluorescence multi-harmonic imaging of biological samples and offers a practical and compact alternative for the clinical translation of nonlinear microscopy. While this supercontinuum covered the visible spectrum (550-900 nm) and the near-infrared region (950-1200 nm), the pulses within 1030-1150 nm produced label-free volumetric chemical images of ex vivo chinchilla kidney, thus validating the supercontinuum from bulk crystals as a powerful source for multimodal nonlinear microscopy.