X-ray Phase Imaging Research Articles

Development of 1-D X-ray beam diffuser for multilayer monochromator and its application to X-ray phase tomography

Development of 1-D X-ray beam diffuser for multilayer monochromator and its application to X-ray phase tomography

Density of fresh wall of acute aortic dissection with synchrotron-based x-ray phase tomography.

The mechanisms behind the onset of acute aortic dissection have not been fully elucidated. We developed dynamic Synchrotron-based X-ray phase tomography to quantitatively study the dynamics of biological samples and applied it to the fresh aortic wall in acute type-A aortic dissection. Fresh, ring-shaped aortas undergoing aortic repair in acute type-A aortic dissection were measured in a container filled with normal cold saline within 24 hours of surgery. As a control, we obtained five formalin-fixed normal ascending aortas from autopsies (female : 2, 59.7 (SD : 5.5) years). To evaluate the quantitative morphological change, we estimated the density at five each step stretched by 2 mm per step. The fresh specimens were analyzed pathologically about the area ratio of elastic fibre. Samples were obtained from five patients (1 man and 4 women, 59.4 (SD: 8.7) years) The overall density of the tunica media in the fresh aorta was 1.062(SD : 0.006) g/cm3 and differed significantly between the dissected and non-dissected portion (1.05(SD : 0.004) vs 1.066(SD : 0.004) g/cm3, respectively; p = 0.0122). When the fresh aortic wall was stretched and became thinner, the density of the tunica media remained unchanged. Compared with pathological findings, area ratio of the elastic fibre of the tunica media were lower in non-dissected portion than normal (48.6 (SD : 7.1) % v.s 60.5 (SD : 5.7) %, p < 0.001). Dynamic-XPCT can trace the deformation process that occurs in situ in fresh aorta in acute type-A aortic dissection. We confirmed that densitometric property of the aortic wall in acute type-A aortic dissection was unchanged during the stretching process.

High resolution X-ray phase contrast imaging for non-destructive testing of composite materials

X-ray imaging is widely used in non-destructive testing dedicated to industry, medical or security domain. In aircraft production, the aerospace industry increasingly integrates carbon fibre reinforced polymers (CFRP), which may develop defects from operational wear, like lightning strikes. To robustly characterize density changes resulting from induced lightning damage in CFRP, multilateral shearing interferometry (MLSI) – a phase imaging technique – have been incorporated on a X-ray laboratory bench. Indeed, such method provides higher contrasts than X-ray attenuation imaging for composite materials and brings complementary information of the imaged sample. However, extracting the phase signal requires conditions of the imaging system and algorithmic strategies, which can lead to the emergence of artifacts in phase images. This thesis work involved the characterisation of these artifacts in the context of MLSI applied to X-ray phase imaging, as well as the development of tracking methods and corrective strategies.

Transport-of-intensity model for single-mask x-ray differential phase contrast imaging

X-ray phase contrast imaging holds great promise for improving the visibility of light-element materials such as soft tissues and tumors. The single-mask differential phase contrast imaging method stands out as a simple and effective approach to yield differential phase contrast. In this work, we introduce a model for a single-mask phase imaging system based on the transport-of-intensity equation. Our model provides an accessible understanding of signal and contrast formation in single-mask x-ray phase imaging, offering a clear perspective on the image formation process, for example, the origin of alternate bright and dark fringes in phase contrast intensity images. Aided by our model, we present an efficient retrieval method that yields differential phase contrast imagery in a single acquisition step. Our model gives insight into the contrast generation and its dependence on the system geometry and imaging parameters in both the initial intensity image as well as retrieved images. The model validity as well as the proposed retrieval method are demonstrated via both experimental results on a system developed in house as well as Monte Carlo simulations. In conclusion, our work not only provides a model for an intuitive visualization of image formation but also offers a method to optimize differential phase imaging setups, holding tremendous promise for advancing medical diagnostics and other applications.

Single shot machine learning based phase retrieval for the X-ray phase imaging

Single shot machine learning based phase retrieval for the X-ray phase imaging

Modulation transfer function (MTF) evaluation for x-ray phase imaging system employing attenuation masks

Objective. Attenuation masks can be used in x-ray imaging systems to increase their inherent spatial resolution and/or make them sensitive to phase effects, a typical example being Edge Illumination x-ray phase contrast imaging (EI-XPCI). This work investigates the performance of a mask-based system such as EI-XPCI in terms of Modulation Transfer Function (MTF), in the absence of phase effects. Approach. Pre-sampled MTF measurements, using an edge, were performed on the same system implemented without masks, with non-skipped masks and finally with skipped masks (i.e. masks in which apertures illuminate every other pixel row/column). Results are compared to simulations and finally images of a resolution bar pattern acquired with all the above setups are presented. Main results. Compared to the detector’s inherent MTF, the non-skipped mask setup provides improved MTF results. In comparison to an ideal case where signal spill-out into neighbouring pixels is negligible, this improvement takes place only at specific frequencies of the MTF, dictated by the spatial repetition of the spill-out signal. This is limited with skipped masks, which indeed provide further MTF improvements over a larger frequency range. Experimental MTF measurements are supported through simulation and resolution bar pattern images. Significance. This work has quantified the improvement in MTF due to the use of attenuation masks and lays the foundation for how acceptance and routine quality control tests will have to be modified when systems using masks are introduced in clinical practice and how MTF results will compare to those of conventional imaging systems.

Organomorphic Silicon Carbide Reinforcing Preform Formation Mechanism

Development of the organomorphic ceramic-matrix composites (CMCs), where the reinforcing preform is built using polymer fibers subject essentially to hot pressing, was motivated by a desire to obtain much higher structural uniformity as well as to reduce the number of the process steps involved in the production of CMCs. This paper addresses the peculiarities of the organomorphic silicon carbide preform formation process. Using X-ray phase analysis, tomography, mass and IR spectroscopy, and thermomechanical and X-ray microanalysis, both the properties of the initial fibers of polycarbosilane (PCS)—the silicon carbide fiber precursor—and their transformation in the preform while heated to 1250 °C under constant pressing at 10–100 kPa were studied. Analysis of the data obtained showed the organomorphic SiC preform relative density at a level of 0.3–0.4 to be ensured by self-bonding of the silicon carbide preform, resulting from the fact that during the low-temperature part of pyrolysis, easily polymerizing substances are released leaving a high coke residue, thus cementing the preform. Another possible factor of SiC framework self-bonding is the destruction of the polymer fibers during pyrolysis of various PCS preforms differing in their methylsilane composition (for example, dimethylsilane), where deposition of silicon carbide on the contacting fibers starts as early as at 450–500 °C.

Simulation Study of Sub-Period Super-Resolution X-ray Phase Imaging with Triangular Phase Grating

X-ray phase contrast image has higher sensitivity to materials with light elements than the conventional absorption contrast. Phase image measurement technique using diffraction gratings can be used in the laboratory. Furthermore, X-ray phase microscope using the diffraction gratings has been also developed. However, phase measurement with diffraction gratings has a drawback that the spatial resolution is limited to the grating period. To overcome this problem, a scanning system using a triangular phase grating has recently been proposed, which is expected to archive a large field of view and a high spatial resolution. This study aims to investigate the feasibility of the system and a deep understanding of the optical system by simulation.

Dynamical X-ray phase imaging of polymer materials under laser engraving

X-ray phase imaging provides higher sensitivity to polymer materials made of light elements than the sensitivity provided by conventional X-ray transmission imaging that relies on absorption contrast. High-speed X-ray phase imaging has recently been studied using pink-beam synchrotron radiation and a Talbot interferometer to enable dynamic observation. In this study, we adopted high-speed X-ray phase imaging for the inner visualization of polymer materials under laser engraving. A sequence of phase-stepping-based phase imaging with a temporal resolution of 5 ms was established by synchronizing an X-ray detector with the linear motions of a grating and a sample. The laser and X-ray paths were aligned orthogonally, and the engraving region was observed from the material surface in the depth direction, in which ablation followed by bubble formation with a certain time delay was demonstrated.

Grating-free quantitative phase retrieval for x-ray phase-contrast imaging with conventional sources

X-ray phase-contrast imaging can display subtle differences in low-density materials (e.g. soft tissues) more readily than conventional x-ray imaging. However, producing x-ray phase images requires significant spatial coherence of the beam which in turn requires highly specialized sources such as synchrotrons, small and low power microfocus sources, or complex procedures, such as multiple exposures with several carefully stepped precision gratings. To find appropriate approaches for producing x-ray phase-contrast imaging in a clinically meaningful way, we employed a grating-free method that utilized a low-cost, coarse wire mesh and simple processing. This method relaxes the spatial coherence constraint and allows quantitative phase retrieval for not only monochromatic but also polychromatic beams. We also combined the mesh-based system with polycapillary optics to significantly improve the accuracy of quantitative phase retrieval.

Element differentiation with a Hartmann- based X-ray phase imaging system

ABSTRACT Significant efforts are currently ongoing in X-ray imaging to provide multimodal imaging systems, targeting better sensitivity and specificity for both biomedical or non-destructive testing applications. Knowing the elemental composition of specific structures, such as breast microcalcifications in mammography, would help to differentiate malign and benign tumours. Standard X-ray Phase Contrast Imaging techniques provide only qualitative information on elements with similar absorption properties. However, their chemical composition can be determined from the measurement of the phase as it is directly related to the optical index of elemental materials. We will show new experimental results obtained with an X-ray phase imaging system based on a Hartmann mask. Early data treatment succeeded in retrieving both the real and imaginary parts of the refractive index. The system demonstrates the capability to discriminate materials based on elemental composition.

Oxysterol Compounds in Mouse Mutant αA- and αB-Crystallin Lenses Can Improve the Optical Properties of the Lens.

PurposeTo investigate how cataract-linked mutations affect the gradient refractive index (GRIN) and lens opacification in mouse lenses and whether there is any effect on the optics of the lens from treatment with an oxysterol compound.MethodsA total of 35 mice including wild-type and knock-in mutants (Cryaa-R49C and Cryab-R120G) were used in these experiments: 26 mice were treated with topical VP1-001, an oxysterol, in one eye and vehicle in the other, and nine mice were untreated controls. Slit lamp biomicroscopy was used to analyze the lens in live animals and to provide apparent cataract grades. Refractive index in the lenses of 64 unfixed whole mouse eyes was calculated from measurements with X-ray phase tomography based on X-ray Talbot interferometry with a synchrotron radiation source.ResultsHeterozygous Cryaa-R49C lenses had slightly irregularly shaped contours in the center of the GRIN and distinct disturbances of the gradient index at the anterior and posterior poles. Contours near the lens surface were denser in homozygous Cryab-R120G lenses. Treatment with topical VP1-001, an oxysterol, showed an improvement in refractive index profiles in 61% of lenses and this was supported by a reduction in apparent lens opacity grade by 1.0 in 46% of live mice.ConclusionsThese results indicate that α-crystallin mutations alter the refractive index gradient of mouse lenses in distinct ways and suggest that topical treatment with VP1-001 may improve lens transparency and refractive index contours in some lenses with mutations.

Bone hierarchical structure: spatial variation across length scales.

Bone is a complex hierarchical biomineralized material, which is special amongst biominerals because it is replete with cells, namely, osteocytes. While bone has been scrutinized for centuries, many questions remain open and new research hints that the ultrastructure of bone, encompassing both the bone matrix itself and the embedded cell network, is much more heterogeneous than hitherto realized. A number of these new findings have been made thanks to the enormous developments in X-ray imaging that have occurred in recent decades, and there is promise that they will also allow many of the remaining open questions to be addressed. X-ray absorption or phase imaging affords high three-dimensional (3D) resolution and allows traversing the length scales of bone all the way down to the fine details of the lacuno-canalicular network housing the osteocytes. Multimodal X-ray imaging provides combined information covering both the length scales defined by the size of the measured volume and tomographic resolution, as well as those probed by the signal that is measured. In X-ray diffraction computed tomography (XRD-CT), for example, diffraction signals can be reconstructed tomographically, which offers detailed information about the spatial variations in the crystallographic properties of the bone biomineral. Orientational information can be obtained by tensor tomography. The combination of both small-angle X-ray scattering (SAXS) and wide-angle X-ray scattering (WAXS) tensor tomography gives information on the orientation of bone nanostructure and crystals, respectively. These new technical developments promise that great strides towards understanding bone structure can be expected in the near future. In this review, recent findings that have resulted from X-ray imaging are highlighted and speculation is given on what can be expected to follow.

Analysis of Fiber Orientation and a Simulation of Damage Fracture Prediction Using an X-ray Phase Imaging Method for Discontinuous Carbon Fiber Random Laminated Molded Products

In chopped carbon fiber tape reinforced thermoplastic（CTT）material, the anisotropic region of fiber orientation after press molding often causes the degradation of mechanical properties and damage and fracture. This study explores means of obtaining the fiber shape and fiber orientation tensors from molded products and then predicting the CTT mechanical properties and damage fracture locations. Extensive fiber shape data obtained by X-ray CT image processing are analyzed using a simple method to create a fiber waviness model.The fiber orientation tensor of the molded product is obtained through X-ray phase imaging. The material properties of a finite element model with CTT are calculated and mapped from the fiber waviness model and orientation tensor, and damage fracture prediction is simulated. Results showed that the fracture positions of both the test and simulation agreed in specimens having large anisotropic regions. However, the specimens with small anisotropic regions did not match. Therefore, the images of strain distribution of the test piece under a tensile load were compared by cross-correlation. Results showed a large correlation between the tensile test and simulation results, thus confirmed the effectiveness of the simulation.

Single-exposure X-ray phase imaging microscopy with a grating interferometer.

The advent of hard X-ray free-electron lasers enables nanoscopic X-ray imaging with sub-picosecond temporal resolution. X-ray grating interferometry offers a phase-sensitive full-field imaging technique where the phase retrieval can be carried out from a single exposure alone. Thus, the method is attractive for imaging applications at X-ray free-electron lasers where intrinsic pulse-to-pulse fluctuations pose a major challenge. In this work, the single-exposure phase imaging capabilities of grating interferometry are characterized by an implementation at the I13-1 beamline of Diamond Light Source (Oxfordshire, UK). For comparison purposes, propagation-based phase contrast imaging was also performed at the same instrument. The characterization is carried out in terms of the quantitativeness and the contrast-to-noise ratio of the phase reconstructions as well as via the achievable spatial resolution. By using a statistical image reconstruction scheme, previous limitations of grating interferometry regarding the spatial resolution can be mitigated as well as the experimental applicability of the technique.

Element differentiation with a Hartmann based X-ray phase imaging system

Significant efforts are currently ongoing in X-ray imaging to provide multimodal imaging systems, targeting better sensitivity and specificity for both biomedical or non-destructive testing (NDT) applications. For example, in mammography, knowing the elemental composition of breast microcalcifications would help to differentiate malign and benign tumours. Standard X-ray Phase Contrast Imaging (XPCI) techniques provide only qualitative information of elements with similar absorption. However, their chemical composition can be determined from the measurement of the phase as it is directly related to the optical index of elemental materials. We will show new experimental results obtained with a novel X-ray phase imaging system based on a Hartmann mask. The system demonstrates capacity to discriminate and quantify the elemental composition. Early data treatment succeeded to retrieve both the real and imaginary parts of the index of refraction.

Development and Optimization of X-ray Phase Tomography with 10 μm Spatial Resolution

Development and Optimization of X-ray Phase Tomography with 10 μm Spatial Resolution

High-Sensitivity X-ray Phase Imaging System Based on a Hartmann Wavefront Sensor

The Hartman wavefront sensor can be used for X-ray phase imaging with high angular resolution. The Hartmann sensor is able to retrieve both the phase and absorption from a single acquisition. The system calculates the shift in a series of apertures imaged with a detector with respect to their reference positions. In this article, the impact of the reference image on the final image quality is investigated using a laboratory setup. Deflection and absorption images of the same sample are compared using reference images acquired in air and in water. It can be easily coupled with tomographic setups to obtain 3D images of both phase and absorption. Tomographic images of a test sample are shown, where deflection images revealed details that were invisible in absorption. The findings reported in this paper can be used for the improvement of image reconstruction and for expanding the applications of X-ray phase imaging towards materials characterization and medical imaging.

High-resolution and sensitivity bi-directional x-ray phase contrast imaging using 2D Talbot array illuminators.

Two-dimensional (2D) Talbot array illuminators (TAIs) were designed, fabricated, and evaluated for high-resolution high-contrast x-ray phase imaging of soft tissue at 10-20 keV. The TAIs create intensity modulations with a high compression ratio on the micrometer scale at short propagation distances. Their performance was compared with various other wavefront markers in terms of period, visibility, flux efficiency, and flexibility to be adapted for limited beam coherence and detector resolution. Differential x-ray phase contrast and dark-field imaging were demonstrated with a one-dimensional, linear phase stepping approach yielding 2D phase sensitivity using unified modulated pattern analysis (UMPA) for phase retrieval. The method was employed for x-ray phase computed tomography reaching a resolution of 3 µm on an unstained murine artery. It opens new possibilities for three-dimensional, non-destructive, and quantitative imaging of soft matter such as virtual histology. The phase modulators can also be used for various other x-ray applications such as dynamic phase imaging, super-resolution structured illumination microscopy, or wavefront sensing.

Phase and dark-field imaging with mesh-based structured illumination and polycapillary optics.

X-ray phase and dark-field (DF) imaging have been shown to improve the diagnostic capabilities of X-ray systems. However, these methods have found limited clinical use due to the need for multiple precision gratings with limited field of view or requirements on X-ray coherence that may not be easily translated to clinical practice. This work aims to develop a practicable X-ray phase and DF imaging system that could be translated and practiced in the clinic. This work employs a conventional source to create structured illumination with a simple wire mesh. A mesh-shifting algorithm is used to allow wider Fourier windowing to enhance resolution. Deconvolution of the source spot width and camera resolution improves accuracy. Polycapillary optics are employed to enhance coherence. The effects of incorporating optics with two different focal lengths are compared. Information apparent in enhanced absorption images, phase images, and DF images of fat embedded phantoms were compared and subjected to a limited receiver operator characteristic (ROC) study. The DF images of the moist and dry porous object (sponges) were compared. The mesh-based phase and DF imaging system constructs images with three different information types: scatter-free absorption images, differential phase images, and scatter magnitude/DF images, simultaneously from the same original image. The polycapillary optic enhances the coherence of the beam. The deblurring technique corrects the phase signal error due to geometrical blur and the limitation of the camera modulation transfer function (MTF) and removes image artifacts to improve the resolution in a single shot. The mesh-shifting method allows the use of a wider Fourier processing window, which gives even higher resolution, at the expense of an increased dose. The limited ROC study confirms the efficacy of the system over the conventional system. DF images of moist and dry porous object show the significance of the system in the imaging of lung infections. The mesh-based X-ray phase and DF imaging system is an inexpensive and easy setup in terms of alignment and data acquisition and can produce phase and DF images in a single shot with wide field of view. The system shows significant potential for use in diagnostic imaging in a clinical setting.