Working Angle Research Articles

Further investigations of a radiation detector based on ionization-induced modulation of optical polarization

Optical property modulation induced by ionizing radiation is a promising approach for ultra-fast, lower time jitter detection of photon arrival time. If successful, this method can be utilized in time-of-flight positron emission tomography to achieve a coincidence time resolution approaching 10 ps. In this work, the optical property modulation based method is further developed with focus on a detection setup based on two crossed polarizers. Previous work demonstrated that such an optical setup could be utilized in radiation detection, though its detection sensitivity needed improvement. This work investigates the angle between polarizers and electric field distribution within the detection crystal to understand and improve the detection sensitivity of an optical polarization modulation based method. For this work, cadmium telluride (CdTe) was studied as the detector crystal . The ‘magic’ angle (i.e. optimal working angle) of the two crossed polarizers based optical setup with CdTe were explored theoretically and experimentally. The experimental results show that the detection sensitivity could be improved by around 10% by determining the appropriate ‘magic’ angle. We then studied the dependence of detection sensitivity on electric field distribution as well as on the bias voltage across the detector crystal using CdTe crystals. The experimental results show that a smaller electrode on the detector crystal, or a more concentrated electric field distribution could improve detection sensitivity. For CdTe, a detector crystal sample with 2.5 mm × 2.5 mm square electrode has twice the detection sensitivity of a detector crystal with 5 mm × 5 mm square electrode. Increasing the bias voltage before saturation for CdTe could further enhance the modulation strength and thus, the sensitivity. Our investigations demonstrated that by determining the proper working angle of polarizers and bias electrical distribution to the detector, we could improve the sensitivity of the proposed optical setup.

Investigation Toiler Weld Blank of SSM 2024 Aluminum Alloys by Friction Stir Welding Joint

The objective of this research was to investigate variables that affected the adhesion of the welded joints for TWBs with FSW in the SSM 2024 aluminum alloys. The results clearly showed that there was a good adhesion of the samples in every experiment. Longitudinal voids can also been found on the top surface of some variables. The average size of cross-links structure of Al2Cu phase (β phase) in SZ, broken into smaller pieces, was around 4 to 7 μm and evenly mixed with alpha phase (α phase). The effect of fracture of Al2Cu phase promoting better mechanical properties. The appropriate tensile strength from the experiment came from variables at the work angle at 15o, rotation speed at 2720 rpm, and welding speed 60 mm/min which provided maximum tensile strength value at 205.0 MPa and the maximum average hardness at 132.4 HV, higher than the weld region. The assessment results showed that the differences in welding variables resulted in different mechanical properties.

Global optimization-based reference star differential imaging for high-contrast exoplanet imaging survey

ABSTRACT We propose a data reduction approach called global optimization-based reference star differential imaging (G-RDI), which can be used for exoplanet imaging survey, where large numbers of target stars from the same young stellar association are imaged and where no field rotation is needed. One of the unique features of our G-RDI is that we select reference stars from other scientific target stars in the same stellar association to optimize for high-contrast imaging with a target star, which maximizes the observational efficiency and also delivers good performance to remove the speckle noise so that high contrast is achievable even at a small inner working angle (IWA) to the host star of being imaged. We proposed the G-RDI that is optimized for high-contrast exoplanet imaging at a small IWA and to provide a contrast that is significantly better than the current reference star differential imaging (RDI) method. In addition, we also propose the use of multiple reference stars and found that our G-RDI can further deliver better performance in that case. The result was compared with other exoplanet data reduction techniques, including the traditional RDI, and it indicated that our G-RDI with two reference stars can significantly improve the contrast performance at a small IWA with a high observational efficiency – two critical features that current data reduction techniques cannot offer. This approach could be used with both equatorial and alt-azimuth mount telescopes, and provides a new option for future exoplanet imaging surveys with high observational efficiency at a small IWA.

Optical verification experiments of sub-scale starshades

Starshades are a leading technology to enable the detection and spectroscopic characterization of Earth-like exoplanets. In this paper we report on optical experiments of sub-scale starshades that advance critical starlight suppression technologies in preparation for the next generation of space telescopes. These experiments were conducted at the Princeton starshade testbed, an 80 m long enclosure testing 1/1000th scale starshades at a flight-like Fresnel number. We demonstrate 1e-10 contrast at the starshade's geometric inner working angle across 10% of the visible spectrum, with an average contrast at the inner working angle of 2.0e-10 and contrast floor of 2e-11. In addition to these high contrast demonstrations, we validate diffraction models to better than 35% accuracy through tests of intentionally flawed starshades. Overall, this suite of experiments reveals a deviation from scalar diffraction theory due to light propagating through narrow gaps between the starshade petals. We provide a model that accurately captures this effect at contrast levels below 1e-10. The results of these experiments demonstrate that there are no optical impediments to building a starshade that provides sufficient contrast to detect Earth-like exoplanets. This work also sets an upper limit on the effect of unknowns in the diffraction model used to predict starshade performance and set tolerances on the starshade manufacture.

Multilevel Hemilaminotomy Windows for the Surgical Management of Spinal Epidural Lipomatosis Causing Syringomyelia: Technical Note and Literature Review

Spinal epidural lipomatosis (SEL) is the excessive accumulation of extradural adipose tissue. Severe cases could result in myelopathy, and very rarely, in syringomyelia formation. Surgery has been associated with high morbidity and mortality, and no proven long-term benefits. The objective was to provide a technical description of an efficient and cost-effective procedure for multilevel thoracic decompression without requiring spinal instrumentation. A technique of multilevel hemilaminotomy windows is described in a patient with severe thoracic SEL causing syringomyelia. A 3-dimensional spine model was created to illustrate the technique and working angles. We performed a literature review by searching PubMed, Ovid Embase, and Scopus electronic databases with the predetermined inclusion criteria of cases with spinal lipomatosis and a fluid cavity within the spinal cord. The patient's deficit and syringomyelia resolved postoperatively. A review of the literature revealed only 3 cases of syringomyelia secondary to SEL. Syringomyelia expansion occurred in all cases leading to progressive neurologic decline, and surgery with removal of the excessive adipose tissue resolved the syringomyelia and improved the neurologic functioning in all cases. This technique of multilevel alternating hemilaminotomy "windows" allows for safe and effective decompression and resection of the excessive adipose tissue with reduced operative time and without requiring spine instrumentation. The technique maintains the integrity of the posterior column, thus reducing the risk of postdecompression deformity. Careful bipolar electrocoagulation of internal vertebral veins and meticulous hemostasis is key for minimizing the intraoperative blood loss and avoiding postoperative hematoma formation.

A Smart Operator Assistance System Using Deep Learning for Angle Measurement

Manual workstations play a critical role in flexible assembly lines by enabling human responses to reconfiguration that is faster than machine responses. As a result, human is more adaptive and sometimes unreplaceable by machines in complex assembly. However, with the increasing complexity of tasks, product quality has become highly susceptible to human error due to increments in operators’ cognitive load. One of the errors that affect assembly quality is the operator’s use of a handheld tool with an unfavorable working angle when handling the workpiece. In this case, an assistive mechanism to remind workers about the wrong working angle is necessary to support the process. To this end, this study proposes an angle monitoring system to inspect the working angle of handheld tools and provide feedback in real time with minimal interruption to the assembly process. The proposed system consists of an angle measurement model and an action recognition model, which are both built using deep-learning-based object detection algorithm. Besides, the system was designed with flexibility that it is applicable to different tools and assembly tasks. A case study on fastening a high-end graphical processing unit card is investigated to evaluate their performance. Results show 95.83% and 99.83% accuracies of the models. In practice, the proposed study is expected to facilitate assembly quality by preventing the failure of angle-related operations in a timely and reliable manner.

Flexible Extrinsic Parameter Calibration for Multicameras With Nonoverlapping Field of View

In many measurement applications using multicameras, there is often a nonoverlapping field of view (nFOV) between multicameras. It benefits greatly from having all of the cameras unified in a single coordinate frame by means of common spatial constraints. However, it is very difficult to establish common spatial constraints for accurate and quick calibration of the extrinsic parameters between multicameras in the case of long working distance, asymmetric working angle, or limited working space. To overcome these issues, we propose a flexible calibration method using a camera rig, which can be easily modeled as a hand–eye calibration problem and solved by only several sets of calibration images. To further improve the calibration accuracy, the camera intrinsic parameters, lens distortion coefficients, and extrinsic parameters are optimized simultaneously, similar to binocular calibration. However, this causes calculation instability of multiparameters. We extend the epipolar constraint to two images with an nFOV and add it into the optimization objective function together with the reprojection error, which ensures the basic consistency of intrinsic parameters before and after optimization, and reduce the fluctuation caused by the number of images involved in calibration. Experiments and application have proved that the proposed new methods are feasible and effective.

Transpars approach for L5-S1 foraminal and extra-foraminal lumbar disc herniations: technical note.

The short pars and the narrowed surgical corridor for far lateral L5S1 herniation make the transpars approach challenging. The aim of this study is to determine the feasibility, efficacy, and safety of the transpars microscopic approach for the treatment of L5-S1 foraminal and extraforaminal lumbar disc herniation. From 2015 to 2019, patients with L5-S1 far lateral lumbar disc herniation were prospectively recruited. Drug intake, working days lost, NRS-leg, NRS-back, nerve-root palsy, Oswestry disability-index, Macnab criteria were recorded before surgery and at follow-up. Patients were seen at 1-6-12 months after surgery. Lumbar dynamic X-rays were performed at 6-12 months after surgery and again at 2-4 years after surgery. Key-steps of surgery are described. Fourteen patients were enrolled. NRS-leg and NRS-back scores significantly improved (from 7.93 to 1.43 and from 3.2 to 0.6, respectively; P<0.0001). Oswestry Score significantly decreased (from 63.14 to 19.36 at 12 months; P<0.0001). L5 Root palsy improved in all cases (from 3.72/5 to 5/5; P<0.0001). At 12-months, excellent or good outcome (Macnab criteria) was achieved in 12 (85.7%) and 2 (14.3%) patients, respectively. All patients who were not retired returned to work within 30 days after surgery. No recurrence, instability or re-operations occurred. The trans pars microscopic approach is feasible, safe, and effective for L5-S1 foraminal and extraforaminal disc herniation. During surgery, the key-point is the oblique working angle, directed caudally, parallel to L5 pedicle. The iliac crest does not seem to constitute an obstacle.

Primary Repair of Posteriorly Located Anterior Skull Base Dural Defects Using Nonpenetrating Titanium Clips in Cranial Trauma.

Objective Primary repair of posteriorly located anterior skull base (ASB) dural defects following cranial trauma is made difficult by narrow operative corridors and adherent dura mater. Inadequate closure may result in continued cerebrospinal fluid (CSF) leak and infectious sequelae. Here, we report surgical outcomes following the use of nonpenetrating titanium microclips as an adjunctive repair technique in traumatic anterior skull base dural defects extending from the olfactory groove to the tuberculum sellae. Methods All trauma patients who underwent a bifrontal craniotomy from January 2013 to October 2019 were retrospectively reviewed. Patients with ASB defects located at posterior to the olfactory groove were analyzed. Patients with isolated frontal sinus fractures were excluded. All patients presented with CSF leak or radiographic signs of dural compromise. Patients were divided according to posterior extent of injury. Patient characteristics, imaging, surgical technique, and outcomes are reported. Results A total of 19 patients who underwent a bifrontal craniotomy for repair of posteriorly located ASB dural defects using nonpenetrating titanium microclips were included. Defects were divided by location: olfactory groove (10/19), planum sphenoidale (6/19), and tuberculum sellae (3/19). No patients demonstrated a postoperative CSF leak. No complications related to the microclip technique was observed. Clip artifact did not compromise postoperative imaging interpretation. Conclusion Primary repair of posteriorly located ASB dural defects is challenging due to narrow working angles and thin dura mater. Use of nonpenetrating titanium microclips for primary repair of posteriorly located dural defects is a reasonable adjunctive repair technique and was associated with no postoperative CSF leaks in this cohort.

Contralateral Interhemispheric Transfalcine Transprecuneus Approach: Advancing Operative Angles to Deep-Seated Lesions

The reach to expose the peritrigonal/atrial territories poses special challenges. The highly functional overlying cortices and white matter tracts, such as the optic radiations lateral to the ventricle, postcentral gyrus laterally and more superficially, and the thalamus anteroinferiorly, constrain the surgical corridors to the atrium. Standard interhemispheric or transcortical approaches involve significant retraction and resection of the normal parenchyma. In this offering, the authors describe the contralateral posterior interhemispheric transfalcine transprecuneus approach (PITTA), which provides flexible working angles while protecting the functional brain tissues. In summary, the PITTA is founded on the concept of using a contralateral operative trajectory to augment a more tangential working angle to the more difficult-to-reach lateral target through a midline route. The PITTA emphasizes the importance of operative working angles (versus necessary operative space) through less disruptive exposures as a more viable parameter for achieving desirable results.

Rotor Position Alignment of FSTPI Based PMSM Drive Using Low Frequency Signal Injection

A PMSM drive with an incremental encoder or using sensorless control requires alignment to a predetermined rotor position (initial position) or initial rotor position detection at start-up. It is desired to lock the rotor to a known state (usually zero angle) at start-up if the initial rotor position detection is not available or difficult to obtain. In this work, a simple and proper zero angle initial rotor position alignment of four-switch three-phase (FSTP) inverter-based PMSM drive is proposed. Low-frequency voltage signal is applied to the d-axis voltage reference of the open-loop FSTPI based PMSM drive scheme without requiring complex trigonometric calculations, PI current regulators and current sensing. Therefore, fluctuated capacitor voltages at the DC-link are obtained allowing current flown through phase a locking the rotor with zero angle, properly. The proposed method has been implemented using a low-cost FSTP voltage source inverter (VSI) for PMSM drive with a floating-point TMS320F28335 DSP. The effectiveness and the feasibility of the proposed zero angle initial rotor position alignment method for PMSM driven by FSTP inverter have been demonstrated through experimental results.

Value of the surgeon\u2019s sightline on hologram registration and targeting in mixed reality

PurposeMixed reality (MR) is being evaluated as a visual tool for surgical navigation. Current literature presents unclear results on intraoperative accuracy using the Microsoft HoloLens 1®. This study aims to assess the impact of the surgeon’s sightline in an inside-out marker-based MR navigation system for open surgery.MethodsSurgeons at Akershus University Hospital tested this system. A custom-made phantom was used, containing 18 wire target crosses within its inner walls. A CT scan was obtained in order to segment all wire targets into a single 3D-model (hologram). An in-house software application (CTrue), developed for the Microsoft HoloLens 1, uploaded 3D-models and automatically registered the 3D-model with the phantom. Based on the surgeon’s sightline while registering and targeting (free sightline /F/or a strictly perpendicular sightline /P/), 4 scenarios were developed (FF-PF-FP-PP). Target error distance (TED) was obtained in three different working axes-(XYZ).ResultsSix surgeons (5 males, age 29–62) were enrolled. A total of 864 measurements were collected in 4 scenarios, twice. Scenario PP showed the smallest TED in XYZ-axes mean = 2.98 mm ± SD 1.33; 2.28 mm ± SD 1.45; 2.78 mm ± SD 1.91, respectively. Scenario FF showed the largest TED in XYZ-axes with mean = 10.03 mm ± SD 3.19; 6.36 mm ± SD 3.36; 16.11 mm ± SD 8.91, respectively. Multiple comparison tests, grouped in scenarios and axes, showed that the majority of scenario comparisons had significantly different TED values (p < 0.05). Y-axis always presented the smallest TED regardless of scenario tested.ConclusionA strictly perpendicular working sightline in relation to the 3D-model achieves the best accuracy results. Shortcomings in this technology, as an intraoperative visual cue, can be overcome by sightline correction. Incidentally, this is the preferred working angle for open surgery.

Discrete element method (DEM) simulation to improve performance of a mouldboard skimmer

Historically, most mouldboard plough research has been focused on improving the performance of the mouldboard itself, with very little focus on other plough components such as the skimmer. The skimmer is a critical additional component of the overall mouldboard plough which affects its performance in the field. The skimmer has a significant effect on the ability of the plough to bury topsoil and surface residues and there is a need to understand the effect of speed, depth and critical working angles on both forces and soil movement. Soil bin and analytical studies by Saunders (2002) investigated the potential to improve soil-skimmer interaction. Recent studies have shown that discrete element method (DEM) has the potential to predict both tillage forces and soil movement of tillage implements. In this study experimental and analytical work carried out by Saunders (2002) was replicated using a DEM simulation. A good correlation was obtained between the measured and predicted draught (R2 = 0.9) forces, furrow area (R2 = 0.68) and maximum soil throw (R2 = 0.77) while a fair correlation was obtained between measured and predicted and vertical forces (R2 = 0.5). It was also found that better draught force prediction can be obtained using DEM than with an analytical method. Results of the study showed that DEM has potential to accurately model tillage forces and soil movement and guide improvements to skimmer working angles.

Glancing Angle Deposition and Growth Mechanism of Inclined AlN Nanostructures Using Reactive Magnetron Sputtering

Glancing angle deposition (GLAD) of AlN nanostructures was performed at room temperature by reactive magnetron sputtering in a mixed gas atmosphere of Ar and N2. The growth behavior of nanostructures shows strong dependence on the total working pressure and angle of incoming flux. In GLAD configuration, the morphology changed from coalesced, vertical nanocolumns with faceted terminations to highly inclined, fan-like, layered nanostructures (up to 38°); while column lengths decreased from around 1743 to 1068 nm with decreasing pressure from 10 to 1.5 mTorr, respectively. This indicates a change in the dominant growth mechanism from ambient flux dependent deposition to directional ballistic shadowing deposition with decreasing working pressures, which is associated with the change of energy and incident angle of incoming reactive species. These results were corroborated using simulation of metal transport (SiMTra) simulations performed at similar working pressures using Ar and N separately, which showed the average particle energy and average angle of incidence decreased while the total average scattering angle of the metal flux arriving at substrate increased with increasing working pressures. Observing the crystalline orientation of GLAD deposited wurtzite AlN nanocolumns using X-ray diffraction (XRD), pole-figure measurements revealed c-axis &lt;0001&gt; growth towards the direction of incoming flux and a transition from fiber-like to biaxial texture took place with increasing working pressures. Under normal deposition conditions, AlN layer morphology changed from {0001} to {101¯1} with increasing working pressure because of kinetic energy-driven growth.

The Transpalpebral Versus the Transciliary Variant of the Supraorbital Keyhole Approach: Anatomic Concepts for Aneurysm Surgery.

The supraorbital craniotomy (SOC) is classically performed through a skin incision in the patient's eyebrow. A variant with a skin incision in the patient's eyelid has become increasingly popular in recent years. To compare the transpalpebral and the transciliary variants of the SOC with regard to their potential role in aneurysm surgery. We carried out cadaveric dissections and virtual craniotomies on computerized tomography datasets. The skin incision, the craniotomy location and size, the working angles, and the achievable exposure of neurovascular structures were assessed and compared for both variants of the SOC. The skin incision measured 4 cm for the transpalpebral and 3 cm for the transciliary variant. The skin could be retracted 1.5 cm upward from the lower edge of the orbital rim with the transpalpebral and 2.5 cm upward with the transciliary variant. The craniotomy size was 2.5×1.5 cm for both variants, given that the transpalpebral variant included an orbital osteotomy. The bony opening in the transpalpebral variant was 1 cm more caudal; this restricted the craniocaudal working angles and, thereby, limited the achievable exposure of neurovascular structures in the paraclinoid area and along the sphenoid ridge. If the orbital rim and the anterior aspect of the orbital roof are removed, then the transpalpebral variant of the SOC enables a bony opening that is just as large as that of the transciliary variant. Nonetheless, the more caudal location of the bony opening alters the available working angles and may impede exposure of key structures during aneurysm surgery.

Standalone Totally Thoracoscopic Left Appendage Clipping: Safe, Simple, Standardized

Totally thoracoscopic standalone left atrial appendage exclusion has become a valid treatment option for stroke prevention in patients with a contraindication to anticoagulants. As with most other video-assisted surgeries, this procedure requires appropriate patient and port positioning to obtain the most advantageous working angles and standard thoracoscopic skills. Furthermore it is mandatory to have a closure device specifically designed for the appendage to guarantee efficacy and safety and to optimize surgical placement that allows the best clinical outcomes. Here we describe the surgical technique of a unilateral left-sided thoracoscopic approach for surgical exclusion of the appendage on the beating heart.

Performance limits of adaptive-optics/high-contrast imagers with pyramid wavefront sensors

ABSTRACT Advanced adaptive-optics (AO) systems will likely utilize pyramid wavefront sensors (PWFSs) over the traditional Shack–Hartmann sensor in the quest for increased sensitivity, peak performance and ultimate contrast. Here, we explain and quantify the PWFS theoretical limits as a means to highlight its properties and applications. We explore forward models for the PWFS in the spatial-frequency domain: these prove useful because (i) they emanate directly from physical-optics (Fourier) diffraction theory; (ii) they provide a straightforward path to meaningful error breakdowns; (iii) they allow for reconstruction algorithms with $O (n\, \log(n))$ complexity for large-scale systems; and (iv) they tie in seamlessly with decoupled (distributed) optimal predictive dynamic control for performance and contrast optimization. All these aspects are dealt with here. We focus on recent analytical PWFS developments and demonstrate the performance using both analytic and end-to-end simulations. We anchor our estimates on observed on-sky contrast on existing systems, and then show very good agreement between analytical and Monte Carlo performance estimates on AO systems featuring the PWFS. For a potential upgrade of existing high-contrast imagers on 10-m-class telescopes with visible or near-infrared PWFSs, we show, under median conditions at Paranal, a contrast improvement (limited by chromatic and scintillation effects) of 2×–5× when just replacing the wavefront sensor at large separations close to the AO control radius where aliasing dominates, and of factors in excess of 10× by coupling distributed control with the PWFS over most of the AO control region, from small separations starting with an inner working angle of typically 1–2 λ/D to the AO correction edge (here 20 λ/D).

Increasing the raw contrast of VLT/SPHERE with the dark hole technique

Context. Since 1995 and the first discovery of an exoplanet orbiting a main-sequence star, 4000 exoplanets have been discovered using several techniques. However, only a few of these exoplanets were detected through direct imaging. Indeed, the imaging of circumstellar environments requires high-contrast imaging facilities and accurate control of wavefront aberrations. Ground-based planet imagers such as VLT/SPHERE or Gemini/GPI have already demonstrated great performance. However, their limit of detection is hampered by suboptimal correction of aberrations unseen by adaptive optics (AO). Aims. Instead of focusing on the phase minimization of the pupil plane as in standard AO, we aim to directly minimize the stellar residual light in the SPHERE science camera behind the coronagraph to improve the contrast as close as possible to the inner working angle. Methods. We propose a dark hole (DH) strategy optimized for SPHERE. We used a numerical simulation to predict the global improvement of such a strategy on the overall performance of the instrument for different AO capabilities and particularly in the context of a SPHERE upgrade. Then, we tested our algorithm on the internal source with the AO in closed loop. Results. We demonstrate that our DH strategy can correct for aberrations of phase and amplitude. Moreover, this approach has the ability to strongly reduce the diffraction pattern induced by the telescope pupil and the coronagraph, unlike methods operating at the pupil plane. Our strategy enables us to reach a contrast of 5e−7 at 150 mas from the optical axis in a few minutes using the SPHERE internal source. This experiment establishes the grounds for implementing the algorithm on sky in the near future.

Chronic Reducible Scapholunate Ligament Dissociation: A Simple Surgical Technique for a Complex Injury.

Report the outcomes following chondrectomy of scapholunate (SL) joint, temporary stabilization of the SL joint using Kirshner wires and extensor carpi radialis longus (ECRL) transfer to dorsal scaphoid pole to restore normal SL gap and correct dorsal intercalated ligament instability deformity. Retrospective case series of 11 patients with a mean age of 45 years were treated by the senior author 7 months after SL injury. The SL joint cartilage was removed, the SL joint was stabilized temporarily with 2 Kirshner wires for 8 weeks and ECRL tenodesis to scaphoid dorsally. Visual analog scale, disability of the arm, shoulder, and hand score, wrist flexion and extension range of motion, grip strength, return to work, SL gap, and SL angle were evaluated preoperatively and in last follow-up visit after the procedure. Modified Mayo score and complications were evaluated in the last visit. Average follow-up was 15.6 months. In the last follow-up, the average visual analog scale pain score improved significantly from 6.4 to 1.5. Average postoperative grip strength improved significantly compared with preoperative strength (41 to 56 Ib). Average disability of the arm, shoulder, and hand score improved significantly postoperatively (30 to 18 points). Average Mayo score was satisfactory in the last visit. Average SL gap reduced significantly from 4.1 to 2.8 mm and average SL angle decreased significantly from 82 to 62 degrees. Postoperative extension-flexion arc of motion significantly decreased compared with preoperative measurements. SL advanced collapse developed in 1 case after 15 months follow-up. All patients return to regular work at a mean of 16 weeks. Chronic reducible SL dissociation can be treated affectively with SL chonderectomy, temporary SL stabilization, and ECRL tenodesis to scaphoid to restore radiologic anatomy without compromising strength or work status. Therapeutic type IV.

Thermal Efficiency for Passive Solar Chimney with and Without Heat Storage material

In this study, a different design of passive air Solar Chimney(SC)was tested by installing it in the south wall of insulated test room in Baghdad city. The SC was designed from vertical and inclined parts connected serially together, the vertical SC (first part) has a single pass and Thermal Energy Storage Box Collector (TESB (refined paraffin wax as Phase Change Material(PCM)-Copper Foam Matrix(CFM))), while the inclined SC was designed in single pass, double passes and double pass with TESB (semi refined paraffin wax with copper foam matrix) with selective working angle ((30o, 45o and 60o). A computational model was employed and solved by Finite Volume Method (FVM) to simulate the air induced through the test room by SC effect. The governing equation of Computational Fluid Dynamic (CFD) model was developed by the effective heat capacity method equation to describe the heat storage and release from PCM-CFM. Practical and computational Results referred to increase in thermal conductivity of the paraffin wax that supported by CFM than 10 times, while the ventilation effect is still active for hours after sun set amount. The maximum ventilation mass flow rate with TESB collector was 36.651 kg/hr., when the overall discharge coefficient equals 0.371. Also, the experimental results referred to the best working angle range 45~60o, while the highest approaching temperature (between air and collector) was appeared for the double passes flat plate collector. Results gave higher heat storage efficiency 47% when the maximum solar radiation 780 W/m2 at 12.00 pm, and the energy summation through duration of charging time was 18460 kJ. Double passes SC at 60o angle presented the highest efficiency with value approaching to 73%, while TESB collector efficiency depicted highest efficiency value 70% at 12:00 pm.