Norway Spruce Wood Research Articles

The Effect of the Loading Frequency on the Dynamic Bending Strength of Spruce Wood.

Wood is increasingly being used in construction as an alternative to steel and concrete. As wood is an inhomogeneous material, this has a strong effect on its static and dynamic properties. When timber is used as a load-bearing component, there is a possibility that it will be exposed to unfavourable weather conditions (wind) or dynamic environments (vibrations), leading to fatigue of the material. In this article, the effects of load frequency and load magnitude on the durability of Norway spruce wood (Picea abies) were investigated. The frequencies of 5 and 10 Hz were compared at three load levels of 70%, 80% and 90% of the static breaking force. The research results show that the load magnitude has a major influence on the dynamic strength at the same fatigue frequency. Each increase in load means a lower dynamic strength of the spruce, which is reflected in the load cycles achieved. In addition, the dynamic properties of spruce wood deteriorate with an increasing loading frequency, which is more pronounced at higher loading forces. These test results are the basis for determining the Wöhler curve, which is required as input data for the material properties in numerical calculations to determine the durability of the material.

From deadwood to forest soils: quantifying a key carbon flux in boreal ecosystems

Deadwood represents a dynamic carbon pool in forest ecosystems where microbial decomposition causes fluxes of CO2 to the atmosphere through respiration and organic carbon to the soil through leakage and fragmentation. This study characterises different stages of deadwood of Norway spruce (Picea abies). 35 Norway spruce trees were sampled and categorized on a 0–5 decay scale. For the 14 trees in classes 0–3, two stem discs were collected from two heights. For the 21 trees in classes 4 and 5, a single sample per tree was taken, because decay was relatively uniform throughout the stem. The relative amount of hemicellulose and cellulose declined moderately from decay class 1 to 3 and substantially from decay class 3 to class 4 but small amounts were still present in decay class 5. The relative lignin proportion increased substantially from decay class 3 to 4 and dominated in decay class 5. Relative carbon content increased from 50 to 56% during the decomposition process due to the increasing accumulation of lignin residuals being a typical signature of brown rot decay. A laboratory experiment including three species of brown rot fungi verified decomposition close to 70% of Norway spruce biomass and resulted in 55% carbon content. This was similar to the carbon content in decay class 4 and 5. A novel approach is presented to quantify the carbon flux from deadwood to the soil. First, we calculated the residual proportion of carbon in decayed wood compared to the initial carbon content of live trees. Subsequently, we extended the calculation to determine the amount of remaining carbon from non-decayed wood that was transferred to the soil during each decay class. The approach showed that Norway spruce wood decomposition under field conditions transfers at least 39–47% of the initial wood carbon to the soil carbon pool, depending on soil type. This strengthens the previously under-communicated fact that the carbon flux from deadwood to soil is higher from brown rot decomposition in boreal forests than the corresponding carbon flux in temperate and tropical forests where deadwood is more influenced by white rot fungi.

Interspecies Interactions in Dual Cultures of Selected Fungi Species and Their Influence on the Decomposition of Scots Pine and Norway Spruce Wood Substrates

Interspecies Interactions in Dual Cultures of Selected Fungi Species and Their Influence on the Decomposition of Scots Pine and Norway Spruce Wood Substrates

Advanced Molecular Dynamics Model for Investigating Biological-Origin Microfibril Structures.

Understanding the atomic-scale structure of wood microfibrils is essential for establishing fundamental properties in various wood-based research aspects, including moisture impact, wood modification, and pretreatment. In this study, we employed molecular dynamics simulations to investigate the arrangement of wood polymers, including cellulose, hemicellulose, and lignin, with a primary focus on the composition of softwood, specifically Norway Spruce wood. We assessed the accuracy of our molecular dynamics model by comparing it with available experimental data, such as density, Young's modulus, and glass transition temperature, which ensures the reliability of our approach. A key aspect of our study involved modeling the active sorption site for water interaction with wood polymers. Our findings revealed that the interaction between water and hemicellulose, particularly within the hemicellulose-cellulose interphase, was the most prominent binding site. This observation aligns with prior research in this field, further strengthening the validity of our results.

The economic evaluation of timber obtained from Norway spruce and scots pine grown under different thinning regimes in Lithuania

ABSTRACT In Lithuania, no studies have determined the relationship between the quality and economic benefits of Norway spruce and Scots pine wood based on age, stand density, and various forest management technologies. This study aims to assess and compare the economic benefits of Norway spruce and Scots pine in stands of different initial densities, depending on different forest management measures. This study calculated different pre-commercial thinning intensities 4 times, 3 times, and 2 times and final thinning profitability by stand volume and wood quality parameters modulus of elasticity and bending strength. Moreover, thinning intensities included three initial stand densities of 3000–3100, 2000–2100, and 1000–1100 trees per hectare, and different thinning regimes when the stand was thinned from below at the age of 8–9, 15, 21, and 35 years. The results showed higher profitability in the pre-commercial thinning of low-intensity with higher frequency − 4 thinning operations over the 40 years. However, the high-thinning intensity − 2 thinning operations over 40 years – applied in young Norway spruce and Scots pine stands will reduce wood quality and profitability in the future. The study found that stand thinning of low intensity tends to improve wood quality and the profitability that depends on it. After assessing the wood quality, it turned out that the 40-year-old Scots pine trees were too young to harvest because of low wood quality. However, the timber from Norway spruce trees could be used profitably if there is a market demand.

Assessment of Fungal Resistance and Preservative Retention in Microwave-Pretreated Norway Spruce Wood

This study investigates the effectiveness of microwave treatment (MW) on the antifungal properties of Norway spruce wood and the leaching of preservatives. Given the environmental and health concerns about conventional wood preservatives, this study evaluates microwave treatment as a sustainable pretreatment to limit the leaching of preservatives from wood. In the experiment, wood samples were treated with microwaves at five different energy levels before being impregnated with copper–ethanolamine- and boron-based preservatives. We assessed preservative retention by leaching tests and assessed the resistance of the wood to fungal attack. The results show that MW treatment improves the uptake and fixation of preservatives, reduces leachability, and significantly improves the durability of an otherwise perishable wood against fungal attack. This study emphasises the potential of microwave treatment for wood preservation. It offers an environmentally friendly approach to extending the life of wood products while maintaining their protective properties against decay.

Probing the complexity of wood with computer vision: from pixels to properties.

We use data produced by industrial wood grading machines to train a machine learning model for predicting strength-related properties of wood lamellae from colour images of their surfaces. The focus was on samples of Norway spruce (Picea abies) wood, which display visible fibre pattern formations on their surfaces. We used a pre-trained machine learning model based on the residual network ResNet50 that we trained with over 15 000 high-definition images labelled with the indicating properties measured by the grading machine. With the help of augmentation techniques, we were able to achieve a coefficient of determination (R2) value of just over 0.9. Considering the ever-increasing demand for construction-grade wood, we argue that computer vision should be considered a viable option for the automatic sorting and grading of wood lamellae in the future.

The Possibility of Using Non-Native Spruces for Norway Spruce Wood Replacement—A Case Study from the Czech Republic

European forests are facing ongoing climate change, and certain tree species are being critically impacted. The Norway spruce (Picea abies (L.) Karst.) is one of the most sensitive species to climate fluctuations, a fact manifesting itself through massive dieback resulting in a lack of high-quality timber and timber market destabilization. Therefore, the possibility of wood substitution with non-native spruce species, namely, black spruce (Picea mariana (Mill.) Britt., Sterns, et Poggenburg), Serbian spruce (Picea omorika (Pančić) Purk.), and blue spruce (Picea pungens Engelm.), under the specific conditions of forest reclamations with great potential for future afforestation was tested. Wood density, modulus of rupture, and modulus of elasticity were used to evaluate wood quality in comparison with native Norway spruce. The results confirmed that only the Serbian spruce reached the quality of Norway spruce and even exceeded it in terms of wood density (P. omorika 525 kg·m−3 vs. P. abies 517 kg·m−3) and exhibited comparable parameters with regard to other properties. The density of the other species was significantly lower for blue spruce (476 kg·m−3) and black spruce (468 kg·m−3). A similar trend was found for other wood parameters, which confirmed that Norway spruce quality was nearly comparable with that of Serbian spruce. On the other hand, black spruce and blue spruce did not match the quality of Norway spruce. The within-stem variability of the properties tested was low for all the spruce species examined. In conclusion, the Serbian spruce showed great potential for future usage in forest management and is one of the possible methods of Norway spruce replacement in times of unprecedented forest disturbances under the effects of global climate change.

The staining influence of iron (II) sulphate on Norway spruce wood

The staining influence of iron (II) sulphate on Norway spruce wood The paper presents the results ofresearch on the colour change of Norway spruce (Picea abies L.) wood under the influence of iron (II) sulphatewater solution at three different concentrations (1%, 2%, 3%). The tests were perfomed wood showing defectstypical of coniferous wood. The aim was to determine the possibility of increasing the usefulness of wood withdefects (blue stain, reactive wood). Measurements of color parameters and their changes based on the CIELabcolor space were carried out. The influence of natural weathering on further staining effect was also determined.On the basis of the tests carried out, it was shown that iron (II) sulphate causes greying of Norway spruce (Piceaabies L.) wood and that the concentration of the solution does not have a major effect on color changes. The surfaceof the aged wood was clearly stained and darkened, with the greatest difference in the samples modified with a3% solution.

Mechanical Performance of Heat-Treated Norway Spruce (Picea abies) Wood

In this study, the mechanical characteristics of Norway spruce wood (Picea abies) from Bosnia and Herzegovina were investigated by thermal treatment at three different temperatures (specifically, 180, 190, and 210°C) and treatment durations (namely, 2, 3, and 4 hours). For this purpose, the maximum 4-point bending force, the modulus of elasticity in bending, the compression strength parallel to the grain, and the compression strength perpendicular to the grain in treated and untreated specimens were evaluated. Results indicated that the relationship between temperature and duration modification affects the mechanical properties of wood specimens. The results revealed that the relationship between temperature and duration modification influenced the mechanical properties of the wood samples. Specifically, in terms of compression strength, it was observed that the heat-treated specimens exhibited improved mechanical properties compared to the unmodified specimens. However, for the maximum 4-point bending force and modulus of elasticity, the results indicated a decrease in mechanical properties.

Effects of different pressures and veneer moisture content in adjacent layers on properties of PUF bonded plywood

In practice, for the manufacture of plywood, the veneer is usually dried to a moisture level suitable for bonding. However, anatomical differences within and between veneer sheets are a significant factor and some of them may contribute to significant differences in moisture content (MC). The novelty of this work was to study the possibility of using wood veneers of different MC in adjacent layers in one structure of plywood panels and how this affects the physical and mechanical properties of the panels. The Norway spruce (Picea abies L. Karst) wood veneers with mean MC approximately of 2%, 5% and 7% and phenol-urea-formaldehyde (PUF) resin were used in the experiments. The five-layers plywood panels were manufactured at the two pressing pressures of 0.8 MPa and 1.2 MPa. There was no significant difference in the bending and bonding properties, but only wood failure as measured on bonding specimens which showed higher average values on specimens manufactured with high pressure during hot pressing. Higher differences in MC of each veneer with constant MC of the veneer stack didn’t worse bending and bonding properties of plywood.

Dendrochemical indicators of tree rings reveal historical soil acidification in Swiss forest stands

The deposition of acidifying nitrogen and sulphur compounds from agriculture and fossil fuel combustion has drastically altered the chemical balance of forest soils in many regions of the world, leading to soil acidification with negative impacts on nutrient availability and thus also on tree vitality. The change of nutrient concentrations in the soil solution can be assessed by long-term investigations, however meaningful indicators, reflecting environmental changes, are needed to compare the current nutrient status with past values. We used dendrochemical indicators in stem wood of different tree species to access the impact of acidifying depositions on soil quality and tree nutrition. We selected 328 stem wood samples from 96 trees of Norway spruce (Picea abies), European beech (Fagus sylvatica), Sessile oak (Quercus petrea) and English oak (Quercus robur) from 22 forest sites, which are part of the long-term Intercantonal Forest Observation Program in Switzerland. Four time periods of 20 years were defined according to the emissions of air pollutants between 1910 and 2017. Our results showed a trend of increasing Al concentrations in tree rings of spruce peaking in the most recent time period (2000–2017). Mn and Ca concentrations in spruce and beech wood have decreased significantly throughout the time period 1910–2017. These dendrochemical indicators depended on the soil pH, with higher Al and lower Mn and Ca concentrations for soils with a low pH (pH<4.2). In oak trees the observed dendrochemical changes are confounded with dendrochemical differences between heartwood and sapwood. K and Mg showed inconsistent patterns in all three tree species, which are probably caused by translocation within the stem discs. With the use of piecewise structural equation models (SEM) we highlighted the direct and indirect influences of N deposition on element concentrations in stem wood. The data suggest a relation between increased N deposition and lower base saturation values in the forest soils for all three tree species, which were linked to higher Al concentrations in spruce and lower Mn concentrations in spruce and beech. The relation between Al concentrations in tree rings of Norway spruce and measured base saturation was used to reconstruct past soil base saturation values. It revealed a progressive soil acidification in the long-term forest observation sites. These reconstructed base saturation values were further used to validate modelled values from dynamic biogeochemical models such as SAFE/ForSAFE. This comparison pointed out possible shortcomings such as the lack of organic complexation in those models. Taken together, our analyses showed that element concentrations of Al, Mn, Ca in Norway spruce and European beech stem wood were suitable dendrochemical indicators of environmental change due to soil acidification, as they reflect both direct and indirect effects of air pollutants and chemical soil properties.

Wood Fiber from Norway Spruce—A Stand-Alone Growing Medium for Hydroponic Strawberry Production

There is an increased interest in the hydroponic production of strawberries in protected cultivation systems, and it is, therefore, urgent to develop new, more sustainable growing media alternatives. This study investigated the physical properties of wood fiber produced from Norway spruce (Picea abies (L.) H. Karst.) and peat:wood fiber substrate blends as well as the performance of the wood fiber in comparison to the industry standards, i.e., peat and coconut coir in the cultivation of hydroponic strawberry. Tray plants of the June-bearing strawberry (Fragaria × ananassa Duch.) cultivar ‘Malling Centenary’ were transplanted into five different growing media: a peat (80%) and perlite (20%) mixture, stand-alone (100%) coconut coir and three stand-alone (100%) Norway spruce wood fiber substrates (including coarse textured fibers with compact and loose packing density and compacted fine-textured fibers). Ripe strawberries were harvested and registered throughout the production season. The overall marketable yield was comparable across all the tested growing media; however, after 4 weeks of harvest, both coarse wood fiber and fine wood fiber showed better fruiting performance than the peat-perlite mixture. A trend for earlier berry maturation was observed for all wood fiber-based substrates. Plant parameters recorded after the end of production showed that plant height, number of leaves, and biomass production were higher in coarse wood fiber than in the peat-perlite mixture. Moreover, plants grown in wood fiber-based substrates had less unripe berries and flowers not harvested in comparison to both the peat and coir treatments.

Analysis of Cutting Forces in Cross-Sawing of Wood: A Study of Sintered Carbide and High-Speed Steel Blades

This research deals with the processing of wood using a circular saw, which is associated with several risks and factors that affect the wood-splitting process. One of them is the wear of the teeth of the saw blade that change the magnitude of the cutting forces. The aim of this study is to compare real measured values and theoretical values when processing Norway spruce wood using two types of saw blades, i.e., sintered carbide (SC) and high-speed steel (HSS), with a diameter of 600 mm and 54 and 56 teeth, respectively. Experimental measurements were carried out on a special test device with the possibility of moving the tested wood into the cutting devices and a simple saw blade replacement system. The results of the contributions show significant differences, based on defined factors which represent the cutting and feed speed, which are supported by FEM analysis of cutting forces in the process of cutting wood—when changing the design of the saw blade. The results of the experiment show that the cutting conditions (cutting speed and feed speed) do not have a significant effect on the size of the cutting forces. The theoretical and real stress values for HSS discs ranged from 14 to 22 MPa. Significantly larger differences were recorded for discs with SC, where the real values of the maximum stresses were around 14 MPa and the theoretical ones around 25 MPa. When cutting spruce with a disc with SC slices, the maximum values of the theoretical cutting forces were in the range of 76 to 94 N and the maximum values of the measured cutting forces were in the range of 40 to 44 N.

Energy value of silver fir (Abies alba) and Norway spruce (Picea abies) wood depending on the degree of its decomposition by selected fungal species

Negative environmental impacts related to climate change and social pressure to raise the rotation age of forests contribute to the quality deterioration of harvested wood, including its decomposition by fungi. This paper presents the results of laboratory experiments investigating the decomposition of Norway spruce (Abies alba) and silver fir (Picea abies) wood by selected species of decay fungi: Hericium flagellum and Bondarzewia mesenterica (causing white rot) as well as Rhodofomes roseus (causing brown rot). The decay process affects wood density, elemental composition, net calorific value, as well as the amount and price of the energy contained in the wood. Wood density was measured conventionally using an electronic caliper and laboratory balance. Energy parameters were determined using elemental analyzer and combustion calorimeter. Wood decay was found to adversely affect energy content per unit of wood at a given volume, thus leading to higher prices per unit of energy. Over the 120 days of the experiment, wood parameters were not affected considerably by Hericium flagellum or Bondarzewia mesenterica. Of the three examined fungal species, Rhodofomes roseus caused the highest weight loss of wood and the greatest decrease in its oven-dry density (spruce - a decrease from 409 to 214 kg m−3; fir - a decrease from 420 to 306 kg m−3), unfavorably reducing energy content per 1 m3 of wood (spruce – decrease by 3.8 GJ m−3; fir – decrease by 2.3 GJ m−3) and raising the unit price of energy.

Impact of Wood Age on Termite Microbial Assemblages.

The decomposition of wood and detritus is challenging to most macroscopic organisms due to the recalcitrant nature of lignocellulose. Moreover, woody plants often protect themselves by synthesizing toxic or nocent compounds which infuse their tissues. Termites are essential wood decomposers in warmer terrestrial ecosystems and, as such, they have to cope with high concentrations of plant toxins in wood. In this paper, we evaluated the influence of wood age on the gut microbial (bacterial and fungal) communities associated with the termites Reticulitermes flavipes (Rhinotermitidae) (Kollar, 1837) and Microcerotermes biroi (Termitidae) (Desneux, 1905). We confirmed that the secondary metabolite concentration decreased with wood age. We identified a core microbial consortium maintained in the gut of R. flavipes and M. biroi and found that its diversity and composition were not altered by the wood age. Therefore, the concentration of secondary metabolites had no effect on the termite gut microbiome. We also found that both termite feeding activities and wood age affect the wood microbiome. Whether the increasing relative abundance of microbes with termite activities is beneficial to the termites is unknown and remains to be investigated. IMPORTANCE Termites can feed on wood thanks to their association with their gut microbes. However, the current understanding of termites as holobiont is limited. To our knowledge, no studies comprehensively reveal the influence of wood age on the termite-associated microbial assemblage. The wood of many tree species contains high concentrations of plant toxins that can vary with their age and may influence microbes. Here, we studied the impact of Norway spruce wood of varying ages and terpene concentrations on the microbial communities associated with the termites Reticulitermes flavipes (Rhinotermitidae) and Microcerotermes biroi (Termitidae). We performed a bacterial 16S rRNA and fungal ITS2 metabarcoding study to reveal the microbial communities associated with R. flavipes and M. biroi and their impact on shaping the wood microbiome. We noted that a stable core microbiome in the termites was unaltered by the feeding substrate, while termite activities influenced the wood microbiome, suggesting that plant secondary metabolites have negligible effects on the termite gut microbiome. Hence, our study shed new insights into the termite-associated microbial assemblage under the influence of varying amounts of terpene content in wood and provides a groundwork for future investigations for developing symbiont-mediated termite control measures.

Effect of Seawater with Average Salinity on the Moisture Content, Ash Content and Tensile Strength of Some Coniferous Wood.

In this paper, the differences in mechanical strength tested during the static tensile and compression test of Scots pine (Pinus sylvestris L.), European larch (Larix decidua) and Norway spruce (Picea abies) wood exposed to continuous soaking in water with a salinity of 7‱ were determined. The value of salinity corresponded to the average salinity on the Polish Baltic coast. This paper also aimed to examine the content of mineral compounds absorbed during four cycles of two weeks each. The essence of the statistical research was to identify the effect of the mineral range compounds and salts depending on the mechanical strength of the wood. Based on the results of the experiments, it can be concluded that the medium used has a specific effect on the wood species' structure. The effects of soaking on the wood parameters depend obviously on the type of wood. A tensile strength test of pine, as well as the tensile strength other species, was enhanced by incubating it in seawater. A native sample's initial mean tensile strength was 82.5 MPa, which increased to 94.8 MPa in the last cycle. It was found that the larch wood had the lowest tensile strength difference (9 MPa) of the woods studied in the current study. Four to six weeks of soaking was necessary to notice an increase in tensile strength.

Impact of Norway spruce pre-degradation stages induced by Gloeophyllum trabeum on fungal and bacterial communities

In forest ecosystems, fungi are the key actors in wood decay. They have the capability to degrade lignified substrates and the woody biomass of coniferous forests, with brown rot fungi being common colonizers. Brown rots are typically involved in the earliest phase of lignocellulose breakdown, which therefore influences colonization by other microorganisms. However, few studies have focused on the impact of introducing decayed wood into forest environments to gauge successional colonization by natural bacterial and fungal communities following partial decay. This study aimed to address this issue by investigating the bacterial and fungal colonization of Norway spruce ( Picea abies ) wood, after intermediate and advanced laboratory-based, pre-decay, by the brown rot fungus Gloeophyllum trabeum . Using Illumina metabarcoding, the in situ colonization of the wood blocks was monitored 70 days after the blocks were placed on the forest floor and covered with litter. We observed significant changes in the bacterial and fungal communities associated with the pre-decayed stage. Further, the wood substrate condition acted as a gatekeeper by reducing richness for both microbial communities and diversity of fungal communities. Our data also suggest that the growth of some fungal and bacterial species was driven by similar environmental conditions.

Cellulose Nano Crystals (CNC) as Additive for a Bio-Based Waterborne Acrylic Wood Coating: Decay, Artificial Weathering, Physical and Chemical Tests.

Wood coatings prolong the service life of wood-based products, but they are usually of synthetic origin. The aim of the present article is to reduce the fossil-based compounds in a commercial waterborne acrylic coating by CNC addition and to test its performance. The coatings were applied on European beech and Norway spruce wood in order to test durability against Gloeophyllum trabeum (brown wood rot) and Trametes versicolor (white wood rot). Artificial weathering and blue stain, contact angle, physical tests (adhesion, impact and scratch test), chemical (FTIR) and morpho-anatomical analysis (SEM) were carried out. CNC addition increased viscosity, limiting the spreading of the coating into wood pores as visible after SEM observation, which reduced coating adhesion on the substrate. CNC improved fungal resistance as seen by a reduced mass loss and FTIR spectroscopy thanks to crosslinks formation, which reduced water sorption as well. Color change was not significant, and, on the other hand, glossiness was reduced but resulted as more homogeneous than control. CNC addition gave good results also in blue stain protection. CNC improved scratch resistance, but no visible change to impact was registered. CNC has promising results in coatings depending on wood and fungal species and presence of further commercial additives (biocides).

Volatile organic compounds emitted from Scots pine and Norway spruce wood

Volatile organic compounds emitted from Scots pine and Norway spruce wood