Passive Wireless Sensor Research Articles

A Wireless Passive Pressure Microsensor Fabricated in HTCC MEMS Technology for Harsh Environments

A wireless passive high-temperature pressure sensor without evacuation channel fabricated in high-temperature co-fired ceramics (HTCC) technology is proposed. The properties of the HTCC material ensure the sensor can be applied in harsh environments. The sensor without evacuation channel can be completely gastight. The wireless data is obtained with a reader antenna by mutual inductance coupling. Experimental systems are designed to obtain the frequency-pressure characteristic, frequency-temperature characteristic and coupling distance. Experimental results show that the sensor can be coupled with an antenna at 600 °C and max distance of 2.8 cm at room temperature. The senor sensitivity is about 860 Hz/bar and hysteresis error and repeatability error are quite low.

Passive wireless antenna sensor for strain and crack sensing—electromagnetic modeling, simulation, and testing

This research investigates a passive wireless antenna sensor designed for strain and crack sensing. When the antenna experiences deformation, the antenna shape changes, causing a shift in the electromagnetic resonance frequency of the antenna. A radio frequency identification (RFID) chip is adopted for antenna signal modulation, so that a wireless reader can easily distinguish the backscattered sensor signal from unwanted environmental reflections. The RFID chip captures its operating power from an interrogation electromagnetic wave emitted by the reader, which allows the antenna sensor to be passive (battery-free). This paper first reports the latest simulation results on radiation patterns, surface current density, and electromagnetic field distribution. The simulation results are followed with experimental results on the strain and crack sensing performance of the antenna sensor. Tensile tests show that the wireless antenna sensor can detect small strain changes lower than 20 με, and can perform well at large strains higher than 10 000 με. With a high-gain reader antenna, the wireless interrogation distance can be increased up to 2.1 m. Furthermore, an array of antenna sensors is capable of measuring the strain distribution in close proximity. During emulated crack and fatigue crack tests, the antenna sensor is able to detect the growth of a small crack.

Metamaterial-inspired passive chipless radio-frequency identification and wireless sensing

The presented paper demonstrates how metamaterials with their unique properties and structures derived from metamaterials can offer solutions to overcome technical limitations of passive and chipless wireless sensor and RFID concepts. Basically, the metamaterial approach allows for miniaturization, higher sensitivity, and an extreme geometric flexibility. Miniaturization is certainly important for both, sensing and identification, while higher sensitivity is primarily applicable to sensors. The geometric flexibility is at first important for sensing since it allows for novel sensor concepts. But at least concerning buildup technology, also RFID concepts can benefit from this advantage. The presented examples of metamaterial-inspired passive chipless RFID and wireless sensing can be assigned to the following three categories: metamaterial resonator approaches, composite right/left-handed lines, and frequency-selective surfaces. In this paper, these different concepts are evaluated and discussed with regard to the metamaterial properties. Furthermore, criteria and figures of merit are given, which allow for a fair comparison of passive, chipless concepts and beyond. Finally, these criteria are applied to the presented sensor and identification concepts.

A wireless embedded passive sensor for monitoring the corrosion potential of reinforcing steel

Corrosion of reinforcing steel, which results in premature deterioration of reinforced concrete structures, is a worldwide problem. Most corrosion sensing techniques require some type of wired connection between the sensor and monitoring electronics. This causes significant problems in their installation and long-term use. In this paper we describe a new type of passive embeddable wireless sensor that is based on an LC coil resonator where the resonant frequency is changed by the corrosion potential of the reinforcing steel. The resonant frequency can be monitored remotely by an interrogator coil inductively coupled to the sensor coil. The sensor unit comprises an inductive coil connected in parallel with a voltage dependent capacitor (varactor) and a pair of corrosion electrodes consisting of a reinforcing steel sensing electrode and a stainless steel reference electrode. Change of potential difference between the electrodes due to variation of the corrosion potential of the reinforcing steel changes the capacitance of the varactor and shifts the resonant frequency of the sensor. A time-domain gating method was used for the interrogation of the inductively coupled corrosion sensor. Results of an accelerated corrosion test using the sensor indicate that the corrosion potential can be monitored with a resolution of less than 10 mV. The sensor is simple in design and requires no power source, making it an inexpensive option for long-term remote monitoring of the corrosion state of reinforcing steel.

Wireless overhead line temperature sensor based on RF cavity resonance

The importance of maximizing power transfer through overhead transmission lines necessitates the use of dynamic power control to keep transmission line temperatures within acceptable limits. Excessive conductor operating temperatures lead to an increased sag of the transmission line conductor and may reduce their expected life. In this paper, a passive wireless sensor based on a resonant radio frequency (RF) cavity is presented which can be used to measure overhead transmission line temperature. The temperature sensor does not require a power supply and can be easily clamped to the power line with an antenna attached. Changing temperature causes a change of cavity dimensions and a shift in resonant frequency. The resonant frequency of the cavity can be interrogated wirelessly. This temperature sensor has a resolution of 0.07 °C and can be interrogated from distances greater than 4.5 m. The sensor has a deviation from linearity of less than 2 °C.

A Wireless Passive Sensor for Temperature Compensated Remote pH Monitoring

Temperature must be accounted for in order to provide accurate measurements in electrode-based pH sensors. We present an integrated wireless passive sensor for remote pH monitoring employing temperature compensation. The sensor is a resonant circuit consisting of a planar spiral inductor connected in parallel to a temperature-dependent resistor (thermistor) and a voltage-dependent capacitor (varactor). A pH combination electrode consisting of an iridium/iridium oxide sensing electrode and a silver/silver chloride reference electrode, is connected in parallel with the varactor. A potential difference change across the electrodes due to pH variation of the solution changes the voltage-dependent capacitance and shifts the resonant frequency, while temperature of the solution affects the resistance and changes the quality factor of the sensor. An interrogator coil is inductively coupled to the sensor inductor and remotely tracks the resonant frequency and quality factor of the sensor. The sensor is calibrated for temperature over a range of 25°C -55°C and pH over a 1.5-12 dynamic range. By employing temperature compensation, a measurement accuracy of less than 0.1 pH is achieved and the response time of the sensor is demonstrated to be less than 1 s. The sensor overcomes the pH measurement error due to the temperature dependence of electrode-based passive pH sensors and has applications in remote pH monitoring where temperature varies over a wide range.

Passive Wireless Sensor Platform Utilizing a Mechanical Resonator

This paper presents a new passive wireless sensor platform on the basis of the intermodulation communication principle. The platform utilizes a quartz crystal or other mechanical resonator and it enables a narrow bandwidth and ID-code to the sensor. A previously presented theory for predicting the intermodulation response of the sensor is elaborated and verified by a simulation. The concept is experimentally demonstrated at 1.2 GHz.

Nano Watt CMOS temperature sensor

In this paper, an ultra-low power embedded full CMOS temperature sensor based on sub-threshold MOS operation is designed in a 0.18 μm CMOS technology. It focuses on temperature measurement using the difference between the gate-source voltages of transistors operated in sub-threshold region that is proportional to absolute temperature. By using the proposed scheme the wide range supply voltage of 0.6---2.5 V with inaccuracy of +0.55 °C/V and total power consumption of merely 7 nW at 120 °C is achieved. The performance of the sensor is highly linear and the predicted temperature error is ±2 °C in the range of 10---120 °C. The sensor occupies a small area of 67 × 31 μm2. Ultra-low power consumption of the sensor illustrates proper operation for low power applications such as battery powered portable devices, passive RFID tags and wireless sensor network applications.

Characterization of SiCN Ceramic Material Dielectric Properties at High Temperatures for Harsh Environment Sensing Applications

A novel method is presented in this paper to precisely characterize the dielectric properties of silicon carbon nitride (SiCN) ceramic materials at high temperatures for wireless passive sensing applications. This technique is based on a high quality factor (Q) dielectrically loaded cavity resonator, which allows for accurate characterization of both dielectric constant and loss tangent. The dielectric properties of SiCN ceramics are characterized from 25 °C to 1000 °C. Two different metallization processes are implemented for the measurements with the highest temperatures of 500 °C and 1000 °C, respectively. A custom-made thru-reflect-line calibration kit is used to maximize the measurement accuracy at every temperature point. It is observed that the dielectric constant and loss tangent of the SiCN sample without Boron doping increase from 3.707 to 3.883 and from 0.0038 to 0.0213, respectively, when the temperature is raised from 25 °C to 500 °C, and for the SiCN with Boron doping (SiBCN), the dielectric constant and loss tangent increase from 4.817 to 5.132 and from 0.0020 to 0.0186, respectively, corresponding to the temperature ranging from 25 °C to 1000 °C. Experimental uncertainties for extracted er and tanδ are no more than 0.0004 and 0.0001, respectively. The temperature dependency of Si(B)CN dielectric properties, as well as the dielectrically loaded cavity resonator structure, provides the basis for the development of wireless passive temperature sensors for high-temperature applications.

A Review of Passive Wireless Sensors for Structural Health Monitoring

Wireless sensors for Structural Health Monitoring (SHM) is an emerging new technology that promises to overcome many disadvantages pertinent to conventional, wired sensors. The broad field of SHM has experienced significant growth over the past two decades, with several notable developments in the area of sensors such as piezoelectric sensors and optical fibre sensors. Although significant improvements have been made on damage monitoring techniques using these smart sensors, wiring remains a significant challenge to the practical implementation of these technologies. Wireless SHM has recently attracted the attention of researchers towards un-powered and more effective passive wireless sensors. This article presents a review of some of the underlying technologies in the field of wireless sensors for SHM - with a focus on the research progress towards the development of simple, powerless, yet effective and robust wireless damage detection sensors. This review examines the development of passive wireless sensors in two different categories: (1) use of oscillating circuits with the help of inductors, capacitors and resistors for damage detection; and (2) use of antennas, Radio Frequency Identification (RFID) tags and metamaterial resonators as strain sensors for wireless damage monitoring. An assessment of these electromagnetic techniques is presented and the key issues involved in their respective design configurations are discussed.

A Wireless Inductive-Capacitive Resonant Circuit Sensor Array for Force Monitoring

A wireless passive sensor array based on inductive-capacitive (LC) resonant circuits capable of simultaneously tracking two points of force loading is described. The sensor consisted of a planar spiral inductor connected to two capacitors forming a resonant circuit with two resonant frequencies. When a load was applied to one or both of the parallel plate capacitors, the distance between the plates of the capacitor was altered, thus shifting the observed resonant peaks. Testing illustrated that applied loading to a particular capacitor caused a significant shift in one of the resonant peaks and also a smaller shift in another resonant peak. This interdependence resulted from each capacitive element being connected to the same inductive spiral and was accounted for with a developed analysis algorithm. To validate the experimental observation, a circuit simulation was also generated to model the sensor behavior with changing force/displacement. The novelty of this system lies not only in its wireless passive nature, but also in the fact that a single LC sensor was fashioned to detect more than one point simultaneously.

Frequency selective surface based passive wireless sensor for structural health monitoring

Wireless sensor networks or ubiquitous sensor networks are a promising technology giving useful information to people. In particular, the chipless passive wireless sensor is one of the most important developments in wireless sensor technology because it is compact and does not need a battery or chip for the sensor operation. So it has many possibilities for use in various types of sensor system with economical efficiency and robustness in harsh environmental conditions. This sensor uses an electromagnetic resonance frequency or phase angle shift associated with a geometrical change of the sensor tag or an impedance change of the sensor. In this paper, a chipless passive wireless structural health monitoring (SHM) sensor is made using a frequency selective surface (FSS). The cross type FSS is introduced, and its SHM principle is explained. The electromagnetic characteristics of the FSS are simulated in terms of transmission and reflection coefficients using simulation software, and an experimental verification is conducted. The electromagnetic characteristic change of the FSS in the presence of mechanical strain or a structural crack is investigated by means of simulation and experiment. Since large-area structures can be covered by deploying FSS, it is possible to detect the location of any cracks.

A SU-8-Based Microfabricated Implantable Inductively Coupled Passive RF Wireless Intraocular Pressure Sensor

With the growing demand in noncontact detection of human diseases, this paper presents an implantable passive wireless pressure sensor using an inductively coupled wireless sensing technique, particularly designed to monitor the intraocular pressure (IOP) of glaucoma patients. The microfabricated IOP sensor consists of a planar spiral gold coil inductor, a two-parallel-gold-plate (metal-insulator-metal) capacitor, and a SU-8 pressure-sensitive diaphragm. The IOP sensor is fully encapsulated inside biocompatible SU-8 stacking layers to isolate the IOP sensor from the biological tissue medium environment. By measuring the impedance phase dip frequency shift from the external coil, the IOP signal can be obtained through the implanted IOP sensor. The optimized size of the manually wound external coil was investigated. The readout distance is up to 6 mm from the implanted sensor. Characterization results show that the microfabricated IOP sensor has relatively high sensitivities-7035 ppm/mmHg in air and 3770 ppm/mmHg in saline medium-with pressure resolution lower than 1 mmHg, which is adequate for IOP monitoring application.

Resonant Coupling of a Passive Inductance-Capacitance-Resistor Loop in Coil-Based Sensing Systems

An inductance-capacitance-resistor (LCR) loop is composed, by connecting an inductive coil with a capacitance element end by end. Without any electric connection with other circuits, higher quality factor can be easily obtained. The loop is inserted into the electromagnetic coupling path of coil-based sensing system, such as the case of eddy-current sensor. When the system is working at the natural resonant frequency of the loop, the coupling efficiency and, therefore, the sensing performance could be improved significantly. Protocol systems, simulating the operation cases of wireless passive sensor and eddy current proximity sensor, are constructed and tested experimentally. The results indicate that, in case of coil-coupled wireless passive sensing system, the received signal's amplitude is enlarged remarkably with a coaxially inserted LCR loop. Moreover, when the loop is coaxially placed on top of the sensing coil of eddy current sensor, not only higher sensitivity and resolution, but also larger monotonic detection range could be achieved.

Passive Wireless Temperature Sensor Based on Time-Coded UWB Chipless RFID Tags

In this paper, an RF identification sensor system is developed. It comprises passive sensors and an ultra-wideband (UWB) reader. The sensors are based on time-coded chipless tags. They consist of an UWB antenna connected to a delay line that is, in turn, loaded with a resistive temperature sensor. This sensor modulates the amplitude of the backscattered signals as a function of the temperature. The sensor tags are identified by changing the length of the delay line. In this paper, the operation principle and design of time-coded tags is presented and the integration of sensors in these tags is addressed. In addition, two measurement techniques are compared to implement the UWB reader. The first one is based on frequency sweeping and uses a vector network analyzer. The second one is based on a low-cost UWB radar. A full characterization of the sensor system is provided.

Magnetoelastic resonance sensor for remote strain measurements

A low cost passive wireless strain sensor is proposed. The basis of the sensor is formed by two softmagnetic magnetostrictive ribbons. The first magnetostrictive ribbon transforms mechanical stress into a stress dependent magnetic field. The second ribbon senses this field by magnetoacoustic oscillations. The resonance frequency directly depends on the applied mechanical stress. For the proposed sensor, a gauge factor Gf, which is defined as the relative change of the resonance frequency divided by the strain ɛ, of Gf = 380 is obtained. This is significantly higher than the gauge factor of standard metal foil strain gages.

Effect of Communication Range with Node Coop-eration in Wireless Passive Sensor Networks

Node cooperation is considered in this paper in the existence of two relaying protocols i.e. “Amplify and Forward (AF)” also called “Store and Forward (SF)” and the second relaying protocol is “Decode and Forward”. The two stated protocols are different from each other and perform different operations on received data before retransmitting to next hop. Also the selection of each protocol is varying in accordance to the distance of a sensor node from the destination node (RF source). It is suggested in this literature that a relay node close to the source node will employ Decode and Forward and if it is close to the destination node, then Amplify and Forward will be employed. This work is achieved by first modelling an empirical system consists of single relay, source and destination. And the two relaying protocols (SF and DF) were modelled and implemented. This approach is then extended for three relay nodes and the two sets of relaying nodes were implemented again on every single node and then the output performances were compared. Finally using analytical approach, the communication range or the capacity of RF source to charge the sensor nodes in certain area was also evaluated and it is considered that the relay nodes within the prescribed range are successfully charged in charging stage. And in communication stage, the relay node was allowed to keep at various distances from the source node and evaluate the performance of each relaying protocol on a particular distance from source and destination.

Effect of Channel Coding With Node Cooperation for Wireless Passive Sensor Networks

The Passive sensor nodes are operated in a very low power regime i.e. -10dBm to -30dBm. Due to this fact, there is a high chance of data to be lost or severely corrupted due to overcome of noisy environment. In order to tackle this problem it was suggested that node cooperation is able to combat this. Node cooperation is very helpful in order to take the data node by node until to the final destination, rather to send directly from source to destination. This work is achieved by first modelling an empirical system consists of single relay, source and destination. And the two relaying protocols (SF and DF) were modelled and implemented. This approach is then extended for three relay nodes and the two sets of relaying nodes were implemented again on every single node. The output performances were compared, and further improvement was seen by channel coding.

Determination of RF Source Power in WPSN Using Modulated Backscattering

A wireless sensor network (WSN) is a wireless network consisting of spatially distributed autonomous devices using sensors to cooperatively monitor physical or environmental conditions, such as temperature, sound, vibration, pressure, motion or pollutants, at different locations. During RF transmission energy consumed by critically energy-constrained sensor nodes in a WSN is related to the life time system, but the life time of the system is inversely proportional to the energy consumed by sensor nodes. In that regard, modulated backscattering (MB) is a promising design choice, in which sensor nodes send their data just by switching their antenna impedance and reflecting the incident signal coming from an RF source. Hence wireless passive sensor networks (WPSN) designed to operate using MB do not have the lifetime constraints. In this we are going to investigate the system analytically. To obtain interference-free communication connectivity with the WPSN nodes number of RF sources is determined and analyzed in terms of output power and the transmission frequency of RF sources, network size, RF source and WPSN node characteristics. The results of this paper reveal that communication coverage and RF Source Power can be practically maintained in WPSN through careful selection of design parameters

Passive wireless structural health monitoring sensor made with a flexible planar dipole antenna

Cheap and efficient wireless sensors have been widely studied by electronics and communication technology development. In this paper, a flexible planar dipole antenna based passive wireless strain sensor has been investigated. The planar dipole antenna is designed for X band and made on a flexible polymer substrate using a conventional photolithography process. The fabricated dipole antenna is attached to a nonmetallic cantilever beam and monitors its bending strain. Mechanical strain and load impedance of the dipole antenna can change its resonance frequency, return loss and reflected signal. The return loss and reflected signals of the dipole antenna sensor are characterized by using a network analyzer. The strain sensitivity of the sensor is proportional to the return loss variation with the bending strain of the cantilever beam. The magnitude of reflected signals increases as the bending strain increases.