Filter Bandwidth Research Articles

Wavelength-Switchable Ytterbium-Doped Mode-Locked Fiber Laser Based on a Vernier Effect Filter

A wavelength-switchable ytterbium-doped mode-locked fiber laser is reported in this article. Two Mach–Zehnder interferometers (MZIs, denoted as MZI1, MZI2) with close free spectral ranges (FSRs) are connected in series to form a Vernier effect sensor. By utilizing the filtering effect of the Vernier effect sensor, the wavelength-switchable output of an ytterbium-doped mode-locked fiber laser is realized. When the 3 dB bandwidth of the Vernier effect filter is set to be 5.31 nm around 1073.42 nm, stable dissipative solitons are obtained. Stretching MZI1 horizontally, the central wavelengths of the pulses can be switched among 1073.42 nm, 1055.38 nm, and 1036.22 nm, with a total tunable central wavelength range of 37.2 nm. When the 3 dB bandwidth of the Vernier effect filter is set to be 4.07 nm, stable amplifier similaritons are obtained. Stretching MZI1 horizontally, the central wavelengths of the pulses are switchable among 1072.71 nm, 1060.15 nm, 1048.92 nm, and 1037.26 nm, with a total tunable central wavelength range of 35.15 nm. Compared with traditional fiber interference filters, the Vernier effect filter has a higher sensitivity, making wavelength switching more convenient and providing a wider tuning range for the ytterbium-doped mode-locked fiber laser.

Performance Comparison of Seed Generation Techniques of Stimulated Brillouin Scattering-Based Microwave Photonics Amplifier and Filter

This work presents a Brillouin amplification performance comparison of seed generation techniques using double-sideband suppressed carrier (DSB-SC) and single-sideband suppressed carrier (SSB-SC) modulations. The SSB-SC is obtained using an optical bandpass filter (OBPF) and in-phase and quadrature Mach-Zehnder modulator (IQ-MZM). All three techniques provide high amplification performance with optical signal-to-noise ratio (OSNR) enhancement of 37.47 dB, 33.14 dB, and 32.67 dB using DSB-SC, SSB-SC/OBPF, and SSB-SC/IQ-MZM, respectively. The best seed generation technique is using the DSB with a signal amplification of 62.47 dB. The technique presents ~4 dB higher OSNR enhancement due to the dual-energy transfer obtained from the beating process of the DSB than SSB. A ~3 dB OSNR reduction is found when pump linewidth (LW) was changed from 1kHz to 50 MHz, which suggests using a low-cost pump source whenever the OSNR reduction is not critical. The work also shows that the three techniques required 10 dBm stimulated Brillouin scattering threshold (SBST) to stimulate the process. An additional analysis of DSB-SC shows that a high-carrier suppression during the seed generation technique using MZMs is insignificant to the amplification performance. The high-carrier suppression produces a high seed signal power that distorts the Brillouin gain spectrum (BGS) and the pump depletion region, hence reducing the Brillouin gain (BG). Since carrier suppression is not a primary consideration, a cost-effective MZM with a modest extinction ratio requirement is allowed. The relaxed requirement of the pump’s linewidth and MZM’s extinction ratio suggest a cost-effective development of the SBS-based optical amplifier with narrow filter bandwidth.

Bulk acoustic wave—Solidly mounted resonator with a-SiOCN:H as low-Z material

Bulk acoustic wave (BAW) filters have been proven to be of high demand in today's low power RF front-ends for mobile communication devices. Within the launch of 5G applications worldwide, especially in the region of new radio (nr-1) up to 6 GHz, defined frequency bands require filters of wide bandwidths, while simultaneously featuring steep edges and high out-of-band rejection. Due to the coexistence with 4G LTE (long term evolution) wireless standards as well as advanced data transfer concepts such as carrier aggregation, the increasing complexity of antenna systems forces the implementation of highly selective acoustic filters. In contrast to the widely used surface acoustic wave (SAW) technology, BAW filters appear with superior performance for frequencies above 1 GHz. This work describes the fabrication of a BAW-solidly mounted resonator (BAW-SMR) with a tailored material system of a-SiOCN:H as a low impedance (low-Z) material integrated within its acoustic Bragg mirror. A direct comparison to the widely used low-Z material of SiO2 with an acoustic impedance of around 13 MRayl is demonstrated by two equal resonator stacks by replacing only the uppermost low-Z thin film of the acoustic reflector. A single-mask design was chosen with platinum as a bottom electrode to ensure the most equal growth conditions for the piezoelectric aluminum nitride (AlN) layers on both reflectors’ surfaces featuring either the tailored a-SiOCN:H or standard SiO2. The a-SiOCN:H thin films were deposited by plasma-enhanced chemical vapor deposition and the according acoustic impedance was priorly depicted to 7.1 MRayl, which could be exploited to achieve an increase in the effective coupling coefficient beyond 7% as well as a resonator bandwidth of more than 60 MHz.

Error rates of optically pre-amplified PPM wireless systems with coding and arbitrary optical filter response

We present novel results for the uncoded and coded bit-error probability (BEP) of optically pre-amplified pulse-position modulation (PPM) wireless systems. For uncoded systems, a novel analytic method for the evaluation of the BEP is derived. The method takes into account the non-ideal optical filter response and utilizes a finite Karhunen–Loève series expansion to calculate the BEP. Using the proposed approach, it is possible to accurately evaluate the PPM BEP for arbitrarily shaped filters where the well-established χ2 method only provides approximate results. Considering a Lorentzian filter response, the discrepancy between the two methods amounts to 0.5 dB in a variety of filter bandwidths and PPM modulation orders. The Lorentzian filter response was chosen as an illustrative practical example whose series can be calculated analytically. The proposed method is also valid for any type of optical filter for which the Karhunen–Loève series expansion can be calculated analytically or numerically. Due to the finite number of terms that are required irrespective of the signal energy level, the proposed method can also be applied without loss of accuracy to assess the system performance under the effects of turbulence and adverse weather conditions. For coded systems with Lorentzian filters, Monte-Carlo simulations are utilized to evaluate the BEP performance of the 5G LDPC codes, and it is demonstrated that they impart an energy gain up to 3.3 dB for 4–PPM and 2.3 dB for 16–PPM at a target BEP of 10−5. The optimal code rates are also discussed for several combinations of the optical filter bandwidth and PPM modulation order and it is shown that in almost all of the cases the optimal code rate is 11/13. Moreover, the sum-product and min-sum decoders perform within 0.1 dB from each other for the best code rates, which points towards the utilization of the min-sum decoder in all settings, since its operation does not require knowledge of the filter parameters. Finally, the comparison between the coded systems with Lorentzian and ideal passband filters exhibits the same 0.5 dB discrepancy that was observed for uncoded systems.

Detecting Instantaneous Tidal Signals in Ocean Models Utilizing Streaming Band‐Pass Filters

AbstractThrough the implementation of a streaming filter, output of numerical ocean simulations can be band‐pass filtered at tidal frequencies while the model is running, yielding time series of sinusoidal motions consisting of tidal signals in the filter's target frequency band. The filtering algorithm is developed from a system of two ordinary differential equations that represents the motion of a damped harmonic oscillator. The filter's response to a broadband input signal is unity at its target frequency but vanishes toward the low and high frequency limits. The decay of the filter response is controlled by a dimensionless parameter, which determines the filter's bandwidth. As a result, the filter allows signals within a small frequency band around its target frequency to pass through, while blocking signals outside of its target frequency band. In this work, the filtering algorithm is implemented into the barotropic solver of the Modular Ocean Model version 6 (MOM6) for determining the instantaneous tidal velocities of the semi‐diurnal and diurnal tides. Utilizing the filters, the frequency‐dependent internal wave drag is applied to the semi‐diurnal and diurnal frequency bands separately. The simulation results suggest that the performance of the algorithm is consistent with the filter transfer function in Fourier space. Potential applications of the algorithm also include de‐tiding the model output for nested regional ocean models, especially those for the purpose of operational forecasting.

Miniaturized filter with harmonic suppression characteristics by embedding microstrip resonators in half‐mode substrate‐integrated waveguide resonant cavities

AbstractA novel filter design is proposed that employs harmonic rejection characteristics based on half‐mode substrate‐integrated waveguide resonance cavities and microstrip resonators. The objective is to expand the filter's blocking bandwidth and reduce the filter's size. The filter employs two half‐mode substrate‐integrated waveguide resonant cavities, which serve to effectively reduce the size of the filter. Moreover, the higher‐order modes TE201 and TE202 are unable to propagate within the resonant cavities. The suppression of the TE102 mode is achieved by setting the coupling window between the resonant cavities at the weakest field strength of this mode. Concurrently, two microstrip resonators are integrated into the coupling window, thereby enabling the realization of a fourth‐order filter response with only two resonant cavities. The filter was processed and measured, and the results were found to be in good agreement with the simulation. It is proved that the design method proposed in this paper is feasible.

Design and fabrication of lithium niobate asymmetrical mode resonators toward C-band and Ku-band

Abstract This work presents a laterally excited bulk wave resonator (XBAR) based on the suspended Z-cut lithium niobate thin film. In order to systematically analyze the influence of geometric structure on the performance of resonators, including electromechanical coupling coefficient (kt 2) and quality factor (Q), the pitch of inter-digital transducers and lateral reflective boundary width (D) were optimized via finite element analysis simulation. Besides, the XBARs with the broadband piston mode structure (BPM-XBAR) were further studied, and the transverse displacement was weakened after optimization, hence enhancing the Q value of the targeted mode. Consequently, the fabricated devices exhibited first order asymmetrical (A1) mode resonance at 5.87 GHz with kt 2 of 12.98% and Q of 218, a nearly 70% increase in Q value. The third order asymmetrical (A3) mode resonance occurred at 17.18 GHz with kt 2 of 7.91%. The above devices have the potential to construct large bandwidth and low loss filters toward the C-band and Ku-band.

Low noise signal processing for electrochemical biosensor using narrow bandwidth filter

Abstract Biosensor has an important role in several domains, including medical and environmental applications. The improvement of biosensor measurement system therefore offers a better measurement quality. The objective of this work is the development of the signal processing of electrochemical biosensor for advanced analysis and use. The noise of electrochemical sensor is considered rather higher than the other sensor due to many factors such as electrode area, solution velocity, and particle size in solution, which affect adsorption-desorption process. Moreover, the sensor signal processing also makes contribution to noise level. Therefore, it must be reduced and suppressed to obtain better measurement result. In this paper, a bandwidth optimisation method is proposed and used to improve measurement quality. The system is realized with a transimpedance circuit and low-pass and high-pass filter, so that it offers low noise characteristics. The developed proposed system has provided better improvement than the standard electrochemical biosensor system. The noise of the system can be suppressed to be lower up to 14.3% of the standard transimpedance circuit. This development is promising to give better biosensor measurement.

Characteristics study of a dual-wavelength polarization filter based on gold-filled square lattice photonic crystal fiber

This study proposes a polarization filter based on gold-filled photonic crystal fiber (PCF) with a square lattice structure. Utilizing the finite element method (FEM), the filtering characteristics of the model were numerically simulated. The dispersion relation and loss characteristics of this structure were analyzed, and the optimal structural parameters were obtained through structural adjustments. Furthermore, the performance of the filter was evaluated under a 2% variation in manufacturing tolerances for gold film thickness (), air hole spacing (), and air hole diameters () and (). Results indicated that at the 1310 nm and 1550 nm communication windows, the confinement losses of the filter were 1354.6 dB/cm and 869.04 dB/cm, respectively, while the losses for the -polarization were merely 16.97 dB/cm and 0.98 dB/cm. When the filter length was set to 0.5 mm, the maximum extinction ratios (ERs) for the two windows reached 588.2 dB and 370.6 dB, and the filter bandwidth extended to 640 nm. Moreover, the characteristics of the filter under manufacturing tolerances were computed, revealing that the filter’s performance remained stable and feasible despite manufacturing errors. The proposed rectangular gold-coated PCF is anticipated to have broad applications in optical fiber communication and optical information processing.

Analysis of Heterostructure Formation of Abnormally Oriented Grains in Sputter-Deposited AlScN Films and Its Impact on Bulk Acoustic Wave Devices.

The presence of abnormally oriented grains (AOGs) in sputter-deposited aluminum scandium nitride (AlScN) films significantly degrades their physical properties, compromising the performance of bulk acoustic wave (BAW) devices. This study utilizes first-principles calculations to reveal that in tetrahedral wurtzite AlScN film-doped Sc atoms tend to aggregate at the second nearest-neighbor positions, forming dense ScN octahedral structures. The rock-salt (RS) ScN continued to grow due to further Sc aggregation. However, due to inadequate scandium flux, embryonic RS structures cannot be sustained, resulting in the nucleation of AOGs at the (111) faces of the octahedral ScN structure. Electron microscopy studies indicated that AOGs possess wurtzite structures and originate at tilted grain boundaries. These boundaries were characterized as RS ScN with more Sc atoms. This corroborated the theoretical predictions. BAW resonators and filters fabricated from sputter-deposited AlScN films demonstrate that AOGs degraded the piezoelectricity of AlScN, reducing the resonator's electromechanical coupling coefficient (Keff2). Measurements showed that AOG density increased from edge to center of the 8 in. wafer, resulting in a 3% decrease in average Keff2 in the resonators and a 137 MHz decrease in the filter bandwidth at 5 dB.

Design of highly efficient filtering power amplifier with a wideband response for sub-6 GHz 5G applications

This paper presents the design of a filtering power amplifier (PA) with extra-high power-efficiency and wide bandwidth. To accomplish this, a novel approach is adopted by utilizing a wideband bandpass filter (BPF) as the output matching network (OMN) for the PA. The BPF compromises two paths, where each path consisting of two identical coupled lines that are interconnected to form a ring structure. The suggested configuration eliminates the need for a conventional OMN by integrating the input port of the filter with the drain node of the transistor, resulting in reduced size and losses and improved amplifier performance. The filter concept is illustrated using coupling matrix synthesis. A proof-of-concept filtering PA has been designed using a commercially available 10 W GaN HEMT. This amplifier was designed to operate in the frequency range of 3.0–5.0 GHz, yielding a fractional bandwidth of 50 %. According to achieved results, the drain efficiency and output power are 43.8–70.5 % and 40.2–41.8 dBm, respectively. As a result, the suggested filtering PA demonstrates significant performance in terms of filter bandwidth response and power amplification. Additionally, the proposed filtering PA has a broad operational bandwidth of 3.0–5.0 GHz, which covers the 5G New Radio (NR) n77 (3.3–4.2 GHz), n78 (3.3–3.8 GHz), and n79 (4.4–5.0 GHz) frequency bands.

Modified central frequency mode decomposition for the fault diagnosis of rotating machinery

Abstract Central frequency mode decomposition (CFMD) is a promising tool for complex mechanical signal processing. Some characteristics of CFMD are disclosed by performing a detailed discussion on its decomposing theory in this study. As a result, three deficiencies of CFMD are found through the analysis of characteristics, including the low accuracies of detected central frequencies (CFs), the too wide bandwidth of filters, and the excessive number of the decomposed modes. To address these issues, a modified CFMD (MCFMD) method is proposed for enhancing its performance of fault diagnosis. First, an exchange weighting function is defined to improve the accuracies of detected CFs. Then, the combination of the detected CFs and the separating information of modes is used to optimize the structures of filters for excluding the interferential information as much as possible. Furthermore, the number of the decomposed modes are compressed based the properties of the fault-related modes to facilitate the implementation of the diagnosis tasks. Lastly, a product envelope spectrum is introduced for further enabling the fault characteristic frequency in the extracted fault-related modes to be more prominent while suppressing other noises. Analysis results verified the effectiveness of the MCFMD and its superiority over some existing advanced methods in the fault diagnosis of rotating machinery.

A novel narrowband MEMS filter with extensional mode resonators

This work proposes a novel electrostatic mechanically coupled narrowband filter based on width extensional mode (WEM) resonators. Rectangle plate WEM resonators have the potential for high quality factor (Q) and low motional resistance. The rectangle plate was slotted to reduce thermoelastic loss and optimize mode shape coefficient of WEMs. The Q values of coupled WEM resonators exceed 80,000, enabling a narrow bandwidth filter. A 3λ/4-length coupling beam filter (CBF) was demonstrated. The 3λ/4 coupling beam filter has a center frequency of 79.79 MHz and a bandwidth of 0.024 %. The CBF exhibits an impressive 26.39 dB stopband rejection and 6.97 dB insertion loss with 5.13 dB passband ripple. The MEMS filters presented in this work hold significant potential for applications in wireless communication systems.

Investigation on gain-managed nonlinearity in Mamyshev oscillators

Mamyshev oscillators and gain-managed nonlinear (GMN) amplifiers have the capability to generate high-power sub-50 fs pulses, but their close relationship has not been systematically investigated. In this paper, we numerically study the influence of gain-managed nonlinearity on the laser evolution and output characteristics of the Mamyshev oscillator. The impact of the gain fibre length, as well as the central wavelength and bandwidth of spectral filters on GMN evolution in the laser are investigated. The results indicate that optimizing these cavity parameters can lead to the GMN evolution, which can improve the output peak power by 1.5–4 times in Mamyshev oscillators.

Dual-window polarization filtering characteristics of rectangular photonic crystal fibers

This paper presents a photonic crystal fiber (PCF) polarization filter with a square array arrangement of gold film fillings, allowing for filtering at dual wavelengths. The paper analyzes the dispersion characteristics and loss properties of this structure and optimizes the structural parameters through adjustments to achieve the best performance. At 1310 nm, the confinement losses of x and y polarization fundamental modes are 903.54 dB/cm and 30.51 dB/cm, respectively; at 1640 nm, the confinement losses of y and x polarization fundamental modes are 479.02 dB/cm and 88.72 dB/cm, respectively. The corresponding filtering bandwidths are 390 and 350 nm, while the full width half maximum (FWHM) is 59.56 nm, indicating excellent selectivity and resolution of the filter. The performance metrics, such as confinement loss, extinction ratios, and bandwidth, are compared in the paper with those reported for other filters. Additionally, the study also analyzed the filter’s performance under varying manufacturing tolerances of gold film thickness and air hole diameter by 5%, revealing that the filter’s performance remains stable and feasible even in the presence of errors.

Fully tunable microwave photonic narrow bandpass filter using an on-chip dual-drive microring resonator

We propose and experimentally demonstrate a fully tunable microwave photonic narrow bandpass filter based on phase modulation to intensity modulation (PM-IM) conversion. In the filter implementation, an on-chip dual-drive microring resonator (MRR) is a key component. This resonator leverages a multimode waveguide to enable a high Q-factor. A metallic micro-heater and a lateral PN junction are simultaneously created for resonance wavelength tuning. When one driving signal is applied to the micro-heater, a large tuning range of the resonance wavelength is resulted; when another driving signal is applied to the PN junction, a fast tuning speed of the resonance wavelength is caused. By jointly using two different tuning mechanisms, the realized microwave photonic filter features a large frequency tuning range as well as a fast tuning speed. In addition, the filter bandwidth can also be tuned. A silicon-based dual-drive high-Q racetrack MRR chip is designed, fabricated, and evaluated. By incorporating the chip in a microwave photonic filter system, a bandpass filter with a narrow bandwidth of 1.27 GHz is achieved. An ultra-wide frequency tuning range from 3 to 51 GHz, an ultra-fast tuning speed less than 0.54 ns, and a tunable bandwidth from 1.27 to 4.47 GHz is experimentally demonstrated. This fully tunable filter offers significant potential in future radar and next-generation wireless communication applications.

Generation and evolution dynamics of gain-guided dissipative solitons in a Tm-doped fiber laser

The generation of dissipative solitons from a mode-locked fiber laser can enhance emission energy, while the insertion of a bandwidth filter exposes the system to complexity. This study presents the first generation and evolution dynamics of gain-guided dissipative solitons (GGDSs) in Tm-doped fiber lasers exploiting the finite gain bandwidth. The results highlight the intricate interplay of finite gain bandwidth with dispersion and nonlinearity in governing the dynamics of GGDSs. An increase in pump power significantly broadens the emission spectrum, which in turn introduces the finite gain bandwidth to the generation of GGDSs. Consequently, linear chirp accumulates, promoting high-energy ultrashort pulse generation after external compression. However, an increase in round-trip group delay dispersion leads to a narrower spectral bandwidth, which can weaken the influence of the finite gain bandwidth, resulting in decreased soliton energy and broader pulse duration. The investigation of GGDS evolution dynamics within the cavity also provides us with a deeper insight into the characteristics of GGDS. Overall, this research offers important guidance for designing high-performance Tm-doped fiber lasers with simple structures that fully exploit the finite gain bandwidth.

A methodology for enhancing bandwidth with keeping steepness of the ladder filters exploiting acoustic‐wave‐lumped‐element resonators

AbstractA methodology to acquire a wide bandwidth and steep transition of a hybrid ladder filter with the acoustic‐wave‐lumped‐element‐resonators (AWLRs) structure is proposed. Different from previous works, a unit of the new AWLR structure with two lumped elements respectively in series and shunt is proposed. It can change both the series‐resonant frequency and the parallel‐resonant frequency of the acoustic wave (AW) resonator to enhance the bandwidth of the hybrid ladder filter. For the ladder structure, all the AW resonators possess the same resonant frequency and impedance. This ladder structure is also used to keep the steep transition of the hybrid filter. For the validations, two‐stage and four‐stage AWLRs‐based hybrid filters are designed, manufactured, and tested. They include (1) a two‐stage filter with an insertion loss (IL) of 0.9 dB, a fractional bandwidth (FBW) of 1.90kt2 (kt2 is the electromechanical coupling coefficient), a center frequency of 1249.3 MHz, and (2) a four‐stage filter with the IL of 1.3 dB, the FBW of 1.86kt2, the SF30 dB/3 dB (shape factor defined as 30‐dB bandwidth divided by 3‐dB bandwidth) of 2.52, the figure of merit (defined as FBW divided by SF30 dB/3 dB) is 0.74kt2 which is the best result, a center frequency of 1249.4 MHz.

Acoustic notch filter based on self-collimation sonic crystals

Utilizing the self-collimation effect in two-dimensional (2D) sonic crystals (SCs), we have proposed an acoustic notch filter which is composed of two perfect mirrors and a beam splitter. Numerical simulation shows that by properly designing the inside structure of the 2D SC, the self-collimated acoustic waves with a desired frequency can be trapped between the two mirrors, realizing the notch filtering function. Moreover, the frequency and bandwidth of the notch filter can be arbitrarily adjusted by changing the parameters of the internel structure, in a considerably broad band. Potential applications include acoustic communication and acoustic signal processing, especially for underwater circumstances.

A mechanically coupled MEMS filter with high-Q width extensional mode resonators

This work presents a novel radio frequency (RF) narrowband Si micro-electro-mechanical systems (MEMS) filter based on capacitively transduced slotted width extensional mode (WEM) resonators. The flexibility of the plate leads to multiple modes near the target frequency. The high Q-factor resonators of around 100 000 enable narrow bandwidth filters with small size and simplified design. The 1-wavelength and 2-wavelength WEMs were first developed as a pair of coupled modes to form a passband. To reduce bandwidth, two plates are coupled with a λ-length coupling beam. The 79.69 MHz coupled plate filter (CPF) achieved a narrow bandwidth of 8.8 kHz, corresponding to a tiny 0.011%. The CPF exhibits an impressive 34.84 dB stopband rejection and 7.82 dB insertion loss with near-zero passband ripple. In summary, the RF MEMS filter presented in this work shows promising potential for application in RF transceiver front-ends.