Wide Range Of Clock Frequencies Research Articles

Resistance of the Montgomery Ladder Against Simple SCA: Theory and Practice

The Montgomery kP algorithm i.e. the Montgomery ladder is reported in literature as resistant against simple SCA due to the fact that the processing of each key bit value of the scalar k is done using the same sequence of operations. We implemented the Montgomery kP algorithm using Lopez-Dahab projective coordinates for the NIST elliptic curve B-233. We instantiated the same VHDL code for a wide range of clock frequencies for the same target FPGA and using the same compiler options. We measured electromagnetic traces of the kP executions using the same input data, i.e. scalar k and elliptic curve point P, and measurement setup. Additionally, we synthesized the same VHDL code for two IHP CMOS technologies, for a broad spectrum of frequencies. We simulated the power consumption of each synthesized design during an execution of the kP operation, always using the same scalar k and elliptic curve point P as inputs. Our experiments clearly show that the success of simple electromagnetic analysis attacks against FPGA implementations as well as the one of simple power analysis attacks against synthesized ASIC designs depends on the target frequency for which the design was implemented and at which it is executed significantly. In our experiments the scalar k was successfully revealed via simple visual inspection of the electromagnetic traces of the FPGA for frequencies from 40 to 100 MHz when standard compile options were used as well as from 50 MHz up to 240 MHz when performance optimizing compile options were used. We obtained similar results attacking the power traces simulated for the ASIC. Despite the significant differences of the here investigated technologies the designs’ resistance against the attacks performed is similar: only a few points in the traces represent strong leakage sources allowing to reveal the key at very low and very high frequencies. For the “middle” frequencies the number of points which allow to successfully reveal the key increases when increasing the frequency.

The Demonstration of S2P (Serial-to-Parallel) Converter with Address Allocation Method Using 28 nm CMOS Technology

To improve the performance of analog, RF, and digital integrated circuits, the cutting-edge advanced CMOS technology has been widely utilized. We successfully designed and implemented a high-speed and low-power serial-to-parallel (S2P) converter for 5G applications based on the 28 nm CMOS technology. It can update data easily and quickly using the proposed address allocation method. To verify the performances, an embedded system (NI-FPGA) for fast clock generation on the evaluation board level was also used. The proposed S2P converter circuit shows extremely low power consumption of 28.1 uW at 0.91 V with a core die area of 60 × 60 μm2 and operates successfully over a wide clock frequency range from 5 M to 40 MHz.

A Direct Mapped Method for Accurate Modeling and Real-Time Simulation of High Switching Frequency Resonant Converters

This article presents a direct mapped method (DMM) for real-time simulation of high switching frequency resonant converters. The DMM links state variables to diode statuses and provides an exact and noniterative solution to network equations. The proposed method is implemented on field programmable gate array (FPGA) to simulate an LLC converter with switching frequencies ranging up to 500 kHz. The best reported implementations of DMM achieve a 25-ns simulation time-step for a wide range of clock frequencies, ranging from 40 to 320 MHz.

Ultra-low power dissipation of improved complementary pass-transistor adiabatic logic circuits based on FinFETs

With the technology scaling down, low power dissipation has become one of the research focuses in the field of integrated circuit design. Various types of adiabatic logics have been invented for low-power applications. However, the expanding leakage current degrades the performance of conventional adiabatic logics. In this article, a novel improved complementary pass-transistor adiabatic logic (ICPAL) based on fin-type field-effect transistor (FinFET) devices with ultra-low power dissipation has been presented. The proposed ICPAL takes full advantage of different FinFET operating modes, that is, shorted-gate mode, independent-gate mode, and low-power mode, to make a tremendous reduction in power dissipation. For explication and verification, the power dissipation of different ICPAL standard cells has been investigated and compared with other types of adiabatic circuits based on FinFETs. The results show that the ICPAL circuits have ultra-low power dissipation in a wide range of clock frequencies(30–800 MHz) under the condition of similar number of transistors, and the average reduction in power dissipation is about 23.1%, 75.0%, and 50.0% relative to 2N-2N2P, improved pass-transistor adiabatic logic, and complimentary pass-transistor adiabatic logic, respectively. Furthermore, ICPAL supports a better pre-evaluation of system power dissipation in VLSI design and has an intrinsic characteristic for the resistance to some types of side channel attacks.

A CMOS 1<tex>$times$</tex>–16<tex>$times$</tex>Speed DVD Write Channel IC

Optical recording demands a meticulous write strategy to control the laser beam power and regulate the phase change layer temperature tightly. The width, height, and delay of a string of short pulses applied to the laser diode need to be adjusted in fine steps, and the writing speed varies widely per applications. A multi-phase phase-locked loop (PLL) tracks a wide range of clock frequencies, and provides a low-jitter time base for write pulses. With two enabling circuit concepts, PLL loop filter voltage folding/unfolding and switch-in of parallel MOS resistors in delay cells, it is possible to operate a PLL to cover a frequency range spanning over three octaves with one VCO. A 10-stage differential VCO is phase-locked to the input channel clock ranging from 26 to 420 MHz (1/spl times/-16/spl times/ DVD speed), and its 20-phase outputs are used to generate write pulses. The pulsewidth and delay are programmed with 120 /spl plusmn/ 40 ps time resolution. The prototype chip fabricated in 0.35 /spl mu/m CMOS occupies 3.5/spl times/3.3 mm/sup 2/, and consumes 294 mW at 3.3 V.

A predictive synchronizer for periodic clock domains

An adaptive predictive clock synchronizer for systems on chip incorporating multiple clock domains is presented. The synchronizer takes advantage of the periodic nature of clocks in order to predict potential conflicts in advance, and to conditionally employ an input sampling delay to avoid such conflicts. The result is conflict-free synchronization with maximal throughput and minimal latency. The adaptive predictive synchronizer adjusts automatically to a wide range of clock frequencies, regardless of whether the transmitter is faster or slower than the receiver. The synchronizer also avoids sampling duplicate data or missing any input. A novel method is presented for formal treatment of synchronizers and metastability. Correct operation of the synchronizer is formally proven and verified.

A programmable clock generator that uses noise shaping and its application in switched-capacitor filters

A programmable digital clock generator that produces a wide range of clock frequencies with fine resolution is described. The clock generator consists of a noise-shaping control loop and a number-controlled oscillator. The generated clock has a time-varying period. When this clock is used as the sampling clock in a switched-capacitor filter (SCF) to set its frequency response, the time-varying period causes nonuniform sampling, which is acceptable under certain conditions that are described. Measured performance of a 2-/spl mu/m CMOS implementation of the clock generator is presented. Also, measured data for the clock generator driving two SCF's are reported.< <ETX xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">&gt;</ETX>

Operation of three-phase charge-coupled devices with two-level clocking waveforms

Both theoretical and experimental investigations of three-phase C.C D.'s have been carried out. The results of these investigations show that when these devices are driven by two-level clock pulses with linear edges backwards flow loss is an important loss mechanism. The exact value of the transfer inefficiency is strongly influenced by the clock voltage turn-off time with longer turn-off times giving, in general, lower inefficiencies. It has also been shown that the transfer inefficiency is a function of the charge-packet size and that for a given turn-off time the transfer inefficiency is independent of frequency over a wide range of clock frequencies.