Wearable Robotic Arm Research Articles

Data fusion of multiple kinect sensors for a rehabilitation system.

Kinect-like depth sensors have been widely used in rehabilitation systems. However, single depth sensor processes limb-blocking, data loss or data error poorly, making it less reliable. This paper focus on using two Kinect sensors and data fusion method to solve these problems. First, two Kinect sensors capture the motion data of the healthy arm of the hemiplegic patient; Second, merge the data using the method of Set-Membership-Filter (SMF); Then, mirror this motion data by the Middle-Plane; In the end, control the wearable robotic arm driving the patient's paralytic arm so that the patient can interactively and initiatively complete a variety of recovery actions prompted by computer with 3D animation games.

自己身体拡張を実現する身体装着型三本目の腕の設計と制御

自己身体拡張を実現する身体装着型三本目の腕の設計と制御

軽量化と実用性を考慮した装着型ロボットアームの提案

軽量化と実用性を考慮した装着型ロボットアームの提案

A novel 3-DOF optical force sensor for wearable robotic arm

This paper presents a novel 3-DOF optical force sensor for the wearable robotic arm. Precise sensing of human motion is still a challenge. As human motion detection sensors are expected to generate the real time data, with simultaneous measurement of multiple degrees of freedom. The optical sensing is considered to be standard for monitoring the human motion. The optical sensor is consists of high speed camera with integrated DSP (Digital Signal Processor). The DSP use to detect the changes in the sequence of frames to calculate the direction and displacement of its motion in a plane. On the other hand optical sensor eliminates the requirement of being in contact with the subject. Hand is the end-effecter of the arm and can be controlled by a 3-DOF (degree of freedom) shoulder, 2-DOF elbow and 2-DOF wrist joint. In this paper we present a new technique to measure the human’s hand movement in 3 dimensions translation frame. An intelligent computational method for this sensory system to measure the applied force is also developed. The optical force sensor was calibrated and then several experiments were conducted to check the feasibility of sensory system with the wearable robotic arm.

Optimal Design of a Bio-Inspired Anthropocentric Shoulder Rehabilitator

This paper presents the design of a bio-inspired anthropocentric 7-DOF wearable robotic arm for the purpose of stroke rehabilitation. The proposed arm rehabilitator synergistically utilizes the human arm structure with non-invasive kinematically under-deterministic cable-driven mechanisms to form a completely deterministic structure. It offers the advantages of being lightweight and having high dexterity. Adopting an anthropocentric design concept also allows it to conform to the human anatomical structure. The focus of this paper is on the analysis and design of the 3-DOF-shoulder module, called the shoulder rehabilitator. The design methodology is divided into three main steps: (1) performance evaluation of the cable-driven shoulder rehabilitator, (2) performance requirements of the shoulder joint based on its physiological characteristics and (3) design optimization of the shoulder rehabilitator based on shoulder joint physiological limitations. The aim is to determine a suitable configuration for the development of a shoulder rehabilitator prototype.

Optimal Design of a Bio‐Inspired Anthropocentric Shoulder Rehabilitator

This paper presents the design of a bio‐inspired anthropocentric 7‐DOF wearable robotic arm for the purpose of stroke rehabilitation. The proposed arm rehabilitator synergistically utilizes the human arm structure with non‐invasive kinematically under‐deterministic cable‐driven mechanisms to form a completely deterministic structure. It offers the advantages of being lightweight and having high dexterity. Adopting an anthropocentric design concept also allows it to conform to the human anatomical structure. The focus of this paper is on the analysis and design of the 3‐DOF‐shoulder module, called the shoulder rehabilitator. The design methodology is divided into three main steps: (1) performance evaluation of the cable‐driven shoulder rehabilitator, (2) performance requirements of the shoulder joint based on its physiological characteristics and (3) design optimization of the shoulder rehabilitator based on shoulder joint physiological limitations. The aim is to determine a suitable configuration for the development of a shoulder rehabilitator prototype.