Industrial Water Treatment Research Articles

Phytoremediation of Wastewater Containing Lead and Manganese Ions Using Algae.

Heavy metal pollution of water from industrial discharge is a major problem worldwide. Thus, the quality of the environment and human health are severely affected. Various conventional technologies have been applied for water treatment, but these can be expensive, especially for industrial water treatment, and may have limited treatment efficiencies. Phytoremediation is a method that is successfully applied to remove metal ions from wastewater. In addition to the high efficiency of the depollution treatment, this method has the advantages of a low cost of the operation and the existence of many plants that can be used. This article presents the results of using algae (Sargassum fusiforme and Enteromorpha prolifera) to treat water containing manganese and lead ions. It was observed that maximum efficiencies for wastewater treatment were obtained when was used the algae Enteromorpha prolifera for a 600 min contact time period. The highest wastewater treatment efficiency obtained using Sargassum fusiforme was 99.46%.

Fiber-based super-bridging agents enable efficient contaminant removal via settling and screening: Impact on microplastics, textile fibers, and turbidity

The water treatment industry relies heavily on coagulation and flocculation processes. This technology requires large amounts of chemicals and large settling tanks for floc separation. The flocs formed during conventional treatment are small (<100 µm), which limit their removal by gravitational separation. To improve floc separation, fiber-based super-bridging agents have been added to the coagulation/flocculation process. When fibers were used in combination with a coagulant and flocculant, the flocs formed were 10 – 100 times larger, and settling was remarkably improved. The tested super-bridging agents also led to a 50 % reduction in demand for both the coagulant and flocculant. The use of super-bridging agents is an effective technique for reducing turbidity and improving the removal of emerging contaminants in both synthetic and natural surface water. Formation of very large flocs with fibers also allowed the replacement of settling by screening without any effect on removal of monitored contaminants. Fibrous treatment removed up to 78 % of turbidity when using a 5000 µm screen mesh size, compared to only 45 % with conventional treatment (coagulant and flocculant, no fibers). Super-bridging agents also drastically improved microplastic removal. The fibrous treatment removed 80 % of 15 µm polyethylene beads, compared to only 20 % with the conventional treatment. Such low removal indicates potential concerns regarding the effective removal of smaller microplastics in existing water treatment plants.

Designing of graphene oxide-induced p-NiO/n-MoO3 heterostructures for improved photocatalytic activity through plasmon-enhanced S-scheme mechanism and its biological and electrochemical performance.

An environmentally benign, economically advantageous microwave hydrothermal approach is used in synthesis of desirably tailored graphene oxide-induced p-NiO/n-MoO3 (GNM) heterostructures. Various analytical techniques such XPS, XRD, UPS, EIS, and Mott-Schottky were conducted to comprehend complete morphology and functioning of the novel ternary heterostructure photocatalysts. Also, SEM and HR-TEM images were presented for better interpretation. The strategic plasmonic step scheme (S-scheme) charge migration approach was used to describe the effective charge recombination process. Hydroxyl and oxide active species were corollaries of the reactive radical-scavenging experiments and electron spin resonance. The work function has been confirmed using ultraviolet photoelectron spectroscopy (UPS), which assessed an electron transfer between NiO and MoO3, yielding work function values of 6.32eV and 5.26eV, respectively. The cell apoptosis of the HeLa cell line approves the material's biocompatibility. Cyclic voltammetry and electrochemical impedance spectroscopy reveal electrochemical performance of GNM heterostructures. We anticipate our results would pave the way for current and future applications. In order to ensure eco-restoration such photocatalyst which are eco and cost friendly are synthesized. Assessment of pollutant risks presents the impact of them on human and terrestrial and aquatic animals. Sustainability of material is acknowledge as they use solar light for photocatalysis and dye degradation, and hence can be green material. One such material for the treatment of wastewater, dye-infused waters, and industrial water has been tailored, which is capable of dye degradation, heavy metal, and other pollutant removal. Very importantly, the synthesized material is a biocompatible one.

Electrodialysis Membrane Technology applied to MEG reclamation – a case study

At Beach Energy’s Otway Gas Plant (OGP) the mono-ethylene glycol (MEG) system salt concentration increased significantly following the commissioning of new subsea horizontally completed wells. Therefore, to de-risk future developments, which are anticipated to include similar wells, a salt removal strategy was implemented. The use of MEG for gas hydrate suppression in wet-raw gas subsea or onshore production pipelines is common across the oil and gas industry, with the MEG recycled using well-proven regeneration and/or reclamation technologies. The MEG extracts water that can contain residual salt and minerals, which over time accumulate in the MEG and can lead to several operational issues, including severe fouling in the MEG regeneration plant, production line blockages and production pipeline integrity concerns, such as accelerated corrosion. MEG reclamation is used to minimise salt accumulation and to date, the dominant technologies employed have been vacuum distillation or flash vaporisation. However, since early 2022, electrodialysis (ED) membrane technology has been deployed at the OGP in an effort to find a more cost-effective solution. The technology is proving a viable alternative to a traditional vacuum distillation reclaiming–regeneration process with energy savings of 17–28% for a hybrid ED-Regeneration process with significantly lower capital cost. This paper details the technical and operational challenges overcome to implement the ED reclamation technology in an industry with more stringent regulatory requirements when compared to typical ED applications (e.g. within the water treatment, pharmaceutical, and food and beverage industries), as well as present the main system performance outcomes following 6 months of operation.

Aqueous Phase from Hydrothermal Liquefaction: Composition and Toxicity Assessment

The main obstacle to the widespread use of hydrothermal liquefaction (HTL) for waste and wet biomass recycling is the formation of a significant amount of highly polluted wastewaters. This paper presents an analysis of the chemical composition and toxicity of aqueous phase from the HTL (HTL-AP) of primary and secondary sludge. It was shown that HTL-AP has a high level of organic pollution (total organic carbon (TOC) = 4.2–9.6 g/dm3, chemical oxygen demand (COD) = 7.9–14.0 g/dm3, BOD5 = 6.0–8.1 g/dm3) and high biological toxicity for traditional test organisms (so that dilution ratio, ensuring the death of no more than 50% of organisms (DR50), varied within 64.7–142.2 and 44.9–81.7 for Artemia salina and Paramecium caudatum, respectively). An analysis of HTL-AP composition with NMR-spectroscopy method allowed us to establish that the share of carbon in aliphatic chains was 34.05–41.82% and the content of carbon in carboxyl groups and aromatic rings was 26.42–34.44%. As a result, we can conclude that the main HTL-AP components are fatty carboxylic acids and their derivatives, aromatic carboxylic acids. The content of aldehydes, ketones, and lignin is less than 8%. Biological treatment of HTL-AP in a lab-scale aerobic reactor turned out to be successful, so average COD reduction was 67–95%. Sludge from an industrial waste water treatment plant (petrochemical sector) with a microorganism concentration of 2.7 g/dm3 was used as inoculum. HTP-AP was diluted 1:10 with tap water. The duration of the process was 18 h.

Stabilisation of evaporation and spray drying processes with municipal or reverse osmosis water as an entry point for chlorate during manufacture of skim milk powder

Chlorate is a concern in the food and beverage industry, associated with chlorine sanitisers in industrial processing and water treatment. This study monitored chlorate entry and accumulation points during skim milk evaporation and spray drying when using municipal and reverse osmosis water to stabilise processing equipment. Municipal water was associated with a 9.2 ± 1.7 and 6.6 ± 1.4 fold increase in chlorate on a dry matter basis during the initial transition from water to product for evaporation and spray drying, respectively. This was not observed when the equipment was stabilised with reverse osmosis water, but could vary depending on the time taken to stabilise processing equipment. Once equipment was in a steady state, there was no entry of chlorate into the finished product for processes stabilised using either water sources; the main points of concern are transitionary periods of operation linked to co-mixing of the product and water.

Remediation of Pb (II), Cd (II), and Zn (II) from aqueous solutions using porous (styrene-divinylbenzene)/Cu-Ni bimetallic nanocomposite microspheres: continuous fixed-bed column study.

Bimetallic nanoparticles (BNPs) have been used as a new line of defence against heavy metal contamination among several types of nanoparticles (NPs) due to their enhanced, synergistic activity. In this study, we investigated the adsorption behaviour of porous (styrene-divinylbenzene)/CuNi bimetallic nanocomposite (P(St-DVB)/CuNi BNC) in a continuous flow fixed-bed column and its ability to remove Pb (II), Cd (II), and Zn (II) ions from aqueous solutions. We examined how the initial metal concentration, flow rate, and bed height affected the adsorption characteristics. Experimental results confirmed that the adsorption capacity increased with increase in influent metal concentration and bed height and decreased with increase in flow rate. The breakthrough and the column kinetic parameters were successfully predicted with three mathematical models: Thomas, Yoon-Nelson, and Adams-Bohart models. Both Thomas and Yoon-Nelson models showed good agreement with the experimental results for all the operating conditions. Successful desorption of heavy metals from the P(St-DVB)/CuNi BNC was performed using 0.5 M NaOH solution, and it showed good reusability of the adsorbent during four adsorption-desorption cycles. The results show that P(St-DVB)/CuNi BNC are effective and low-cost adsorbents, and they can be used in real-time large-scale industrial water treatment processes for the removal of heavy metals.

Inhibition Effect of Pseudomonas stutzeri on the Corrosion of X70 Pipeline Steel Caused by Sulfate-Reducing Bacteria.

Microbiologically influenced corrosion (MIC) is a common phenomenon in water treatment, shipping, construction, marine and other industries. Sulfate-reducing bacteria (SRB) often lead to MIC. In this paper, a strain of Pseudomonas stutzeri (P. stutzeri) with the ability to inhibit SRB corrosion is isolated from the soil through enrichment culture. P. stutzeri is a short, rod-shaped, white and transparent colony with denitrification ability. Our 16SrDNA sequencing results verify the properties of P. stutzeri strains. The growth conditions of P. stutzeri bacteria and SRB are similar, and the optimal culture conditions are about 30 °C, pH 7, and the stable stage is reached in about seven days. The bacteria can coexist in the same growth environment. Using the weight loss method, electrochemical experiments and composition analysis techniques we found that P. stutzeri can inhibit the corrosion of X70 steel by SRB at 20~40 °C, pH 6~8. Furthermore, long-term tests at 3, 6 and 9 months reveal that P. stutzeri can effectively inhibit the corrosion of X70 steel caused by SRB.

Value Chain Analysis of Rice Industry by Products in a Circular Economy Context: A Review

The quantity of organic waste generated by agricultural sectors is continually increasing due to population growth and rising food demand. Rice is the primary consumable food in Asia. However, many stakeholders follow a linear economic model such as the “take–make–waste” concept. This linear model leads to a substantial environmental burden and the destruction of valuable resources without gaining their actual value. Because these by-products can be converted into energy generating and storage materials, and into bio-based products by cascading transformation processes within the circular economy concept, waste should be considered a central material. This review examines the composition of rice straw, bran, and husks, and the procedures involved in manufacturing value-added goods, from these wastes. Moreover, starting with an extensive literature analysis on the rice value chains, this work systematizes and displays a variety of strategies for using these by-products. The future development of agricultural waste management is desirable to capitalize on the multi-functional product by circulating all the by-products in the economy. According to the analysis of relevant research, rice straw has considerable potential as a renewable energy source. However, there is a significant research gap in using rice bran as an energy storage material. Additionally, modified rice husk has increased its promise as an adsorbent in the bio-based water treatment industry. Furthermore, the case study of Sri Lanka revealed that developing countries have a huge potential to value these by-products in various sectors of the economy. Finally, this paper provides suggestions for researchers and policymakers to improve the current agriculture waste management system with the best option and integrated approach for economic sustainability and eco- and environmental solution, considering some case studies to develop sustainable waste management processes.

Rapid, Highly-Efficient and Selective Removal of Anionic and Cationic Dyes from Wastewater Using Hollow Polyelectrolyte Microcapsules

Herein, poly (allylamine hydrochloride) (PAH)/ poly (styrene sulfonic acid) sodium salt (PSS) microcapsules of (PAH/PSS)2PAH (P2P MCs) and (PAH/PSS)2 (P2 MCs) were obtained by a layer-by-layer method. The P2 MCs show high adsorption capacity for Rhodamine B (642.26 mg/g) and methylene blue (909.25 mg/g), with an extremely low equilibrium adsorption time (~20 min). The P2P MCs exhibited high adsorption capacities of reactive orange K-G (ROKG) and direct yellow 5G (DY5G) which were 404.79 and 451.56 mg/g. Adsorption processes of all dyes onto microcapsules were best described by the Langmuir isotherm model and a pseudo-second-order kinetic model. In addition, the P2P MCs loaded with reactive dyes (P2P-ROKG), could further adsorb rhodamine B (RhB) dye, and P2 MCs that had adsorbed cationic MB dyes could also be used for secondary adsorption treatment of direct dye waste-water, respectively. The present work confirmed that P2P and P2 MCs were expected to become an excellent adsorbent in the water treatment industry.

Cвободно-радикальная привитая сополимеризация акриламида, 2-акриламидо-2-метилпропансульфоната натрия и хитозана

The method presents obtaining hydrosoluble graft copolymer of complicated structure based on сhitosan, acrylamide (AM), sodium 2-acrylamido-2-methylpropane sulfonic (АМPS-Na) in order to obtain flocсulant which is resistant to salt of transition metals and heat temperature, and in order to use it as a reagent for oil production processes. The obvious advantages of this copolymer can be attributed to its biodegradation due to inclusion of a biopolymer into the composition of the copolymer, which is important for the preservation of ecology, and efficiency of its synthetic analogues. The graft copolymerization acrylamide and sodium 2-acrylamido-2-methylpropane sulfonic onto active sites of chitosan has been performed under condition of high concentration monomers in nitrogen atmosphere using combined initiator system of complex composition under the following order monomers [АА]&gt;[АМПС-Na]. Kinetic study of graft copolymerization has been carried out using thermometry methods. Attempts have been made to describe mathematically the reaction of graft monomers АM and АМPS-Na onto chitosan. The IR spectra analysis of copolymers has been carried out. The study of reaction rate and molecular characteristics of synthesized copolymers has been conducted under changing concentration of chitosan, monomers, ratio components of the initiator system and reaction temperature during synthesis. It has been determined that the averaged energy activation of copolymerization reaction was in the range of reaction temperature 10–25°С. Molecular composition and proposed structure of the grafted copolymers have been determined by the results of viscosity and sedimentation analysis. The results of this study allow to obtain grafted copolymers with specified properties and structure to use them in such areas as sewage and industrial water treatment and mineral industry.

Use of Zebrafish Embryos To Reproduce Human Norovirus and To Evaluate Human Norovirus Infectivity Decay after UV Treatment.

This study reports an essential improvement of the method for replication of human norovirus (HNoV) with the use of zebrafish (Danio rerio) embryos. With three HNoV genotypes and P-types GII.2[P16], GII.4[P16], and GII.17[P31], we demonstrated that this tool had higher efficiency and robustness than the zebrafish larvae as reported previously. When zebrafish larvae were injected with virus (1.6 ± 0.3 log genome copies/10 larvae), a significant increase of virus genome copies was detected at 2 days postinfection (dpi; 4.4 ± 0.8 log genome copies/10 larvae, P < 0.05) and the viral loads started to decrease gradually from 3 dpi. In comparison, when the viruses were injected into the zebrafish embryos, significant virus replication was noticed from 1 dpi and lasted to 6 dpi (P < 0.05). The virus levels detected at 3 dpi had the highest mean value and the smallest variation (7.7 ± 0.2 log genome copies/10 larvae). The high levels of virus replication enabled continuous passaging for all three strains up to four passages. The zebrafish embryo-generated HNoVs showed clear patterns of binding to human histo-blood group antigens (HBGAs) in human saliva by a simple saliva-binding reverse transcription-quantitative PCR (RT-qPCR). Last, in a disinfection study, it was shown that a dose of 6 mJ/cm2 UV254 was able induce a >2-log reduction in HNoV infectivity for all three HNoV strains tested, suggesting that HNoVs were more UV susceptible than multiple enteric viruses and commonly used HNoV surrogates as tested before. IMPORTANCE HNoVs are a leading cause of gastroenteritis outbreaks worldwide. The zebrafish embryo tool as developed in this study serves as an efficient way to generate viruses with high titers and clean background and a straightforward platform to evaluate HNoV inactivation efficacies. It is expected that this tool will not only benefit epidemiological research on HNoV but also be used to generate HNoV inactivation parameters which are highly needed by the water treatment and food industries.

Device Testing: High-Efficiency and High-Uniformity Microwave Water Treatment System Based on Horn Antennas

Microwave heating has excellent potential for applications in wastewater treatment. This study proposes a highly efficient continuous liquid-phase microwave heating system to overcome the problems of low treatment capacity, low dynamic range of loads, and insufficient heating uniformity of the existing equipment. First, a quarter-wavelength impedance-matching layer improves heating efficiency, and the heating uniformity has been enhanced by horn antennas. Second, an experimental system is developed. The simulation and experimental results are consistent, with the microwave system achieving over 90% energy utilization for different thicknesses and concentrations of salt water. Finally, simulations are performed to analyze microwave efficiency and heating uniformity at different flow rates, salinities, dielectric properties, and sawtooth structures. The system can efficiently heat loads with a wide range of dielectric properties, including saline water. Generally, when the permittivity varies from 10 to 80, and the loss tangent varies dynamically from 0.15 to 0.6, more than 90% of microwave efficiency and excellent temperature distribution (The coefficient of temperature variation COV &lt; 0.5) can be achieved. The system’s modular design enables scaling up to further boost processing capacity. Overall, the system provides high-throughput, high-efficiency, high-uniformity, and large-dynamic-range microwave water treatment, which has promising applications in industrial water treatment.

Subcritical Water Treatment for Valorization of the Red Algae Residue after Agar Extraction: Scale-Up from Laboratory to Pilot Plant.

The feasibility of industrial subcritical water treatment on Gelidium sesquipedale residue through scaling up from the lab to pilot system in discontinuous mode (geometric scale-up factor = 50), at 130 and 175 °C (5% biomass), was investigated. The maximum volumes of the reactors were 500 mL at the lab-scale and 5 L at the pilot-scale system. At 175 °C, faster extraction/hydrolysis was observed for the pilot plant, but maximum yields were similar: 71.4 and 78.6% for galactans, 9.8 and 10.4% for glucans, and 92.7 and 86.1% for arabinans in pilot scale and lab scale, respectively, while the yields for proteins accounted nearly 40%. The highest yields for amino acids were observed for the smallest ones, while lower yields were determined for polar amino acids. The total phenolic content and color intensity progressively increased along time at lab scale, while a plateau was reached at the pilot level. Lower extraction yields but reproducible results were obtained at 130 °C. Finally, the pilot scale was essayed at a higher biomass loading (15%), and successful results were obtained, supporting the feasibility of the scaling-up process.

Removal of natural organic matter from surface water sources by nanofiltration and surface engineering membranes for fouling mitigation – A review

Given that surface water is the primary supply of drinking water worldwide, the presence of natural organic matter (NOM) in surface water presents difficulties for water treatment facilities. During the disinfection phase of the drinking water treatment process, NOM aids in the creation of toxic disinfection by-products (DBPs). This problem can be effectively solved using the nanofiltration (NF) membrane method, however NOM can significantly foul NF membranes, degrading separation performance and membrane integrity, necessitating the development of fouling-resistant membranes. This review offers a thorough analysis of the removal of NOM by NF along with insights into the operation, mechanisms, fouling, and its controlling variables. In light of engineering materials with distinctive features, the potential of surface-engineered NF membranes is here critically assessed for the impact on the membrane surface, separation, and antifouling qualities. Case studies on surface-engineered NF membranes are critically evaluated, and properties-to-performance connections are established, as well as challenges, trends, and predictions for the field's future. The effect of alteration on surface properties, interactions with solutes and foulants, and applications in water treatment are all examined in detail. Engineered NF membranes containing zwitterionic polymers have the greatest potential to improve membrane permeance, selectivity, stability, and antifouling performance. To support commercial applications, however, difficulties related to material production, modification techniques, and long-term stability must be solved promptly. Fouling resistant NF membrane development would be critical not only for the water treatment industry, but also for a wide range of developing applications in gas and liquid separations.

Just Suspended Speed Simulation in Torus Reactor Using Multiple Non-Linear Regression Model

In the chemical and water treatment industries, it is necessary to achieve maximum contact between the solid and liquid phase, thus promoting the mass and heat transfer, to obtain a homogeneous solution. Increasing stirring speed is the most recommended solution in different types of reactors: stirred tank, column, and tubular. However, this inadvertently increases the energy consumption of the industry. Determination of the minimum speed, labeled the just suspended speed (Njs) and crucial to attaining homogeneity, has been widely investigated. Numerous studies have been carried out to assess formulas for determining the solid particle speed in various reactor types. Given the limitations of the existing formulations based on a generalization of a unique equation for computing Njs for all soil classifications, it appears that most formulas can only approximate complex phenomena that depend on several parameters. A novel formula was developed, and the results given in this paper demonstrate the effectiveness of generating significant uncertainties for the estimation of Njs. The purpose of this study was the elaboration of experiment-based data-driven formulas to calculate Njs for different particle size classes. Nonlinear multiple regression (MNLR) models were used to generate the new formulas. The gradient descent optimization algorithm was employed to solve the hyperparameters of each novel equation, utilizing supervised learning. A comparison of the data indicated that the unique formulas presented in this study outperformed empirical formulas and provide a useful means for lowering energy consumption, while increasing the heat and mass transfer in torus type reactors.

Pollution and treatment of industrial waste water

Every year, a massive amount of wastewater is discharged into water bodies from various industries, and numerous processes are used to treat wastewater to reduce the number of pollutants. Industrial wastewater can be very different from sewage in terms of its discharge patterns and compositions. The overall scenario is not different for Bangladesh a developing country. Hence, the industrial wastewater treatment process has undergone modification as time passes newly discovered dangerous substances in the industrial wastewater treatment process worldwide. Multiple methods including conventional and advanced methods are upheld in this present paper with advantages and disadvantages also illustrated there. Besides, the potential for integrating two or more technologies to enhance treatment efficiency is also addressed. Considering low cost as well as maintenance purposes, among all the methods, hybrid or integrated technologies are found effective to reduce the contamination level of wastewater.

Copper Recovery from Aqueous Solutions by Hemp Shives: Adsorption Studies and Modeling

This article describes the performance of hemp shives, a co-product of the hemp industry, when used as an adsorbent to recover copper present in aqueous solutions by a batch method. Two materials provided by an industrial partner, namely water-washed hemp shives (SHI-W) and Na2CO3-activated shives (SHI-C), were studied. Two important variables in the water treatment industry, i.e., pH and ionic strength of the solution, were studied to evaluate their impact on the purification performance of the materials. The results obtained clearly indicated that the performance in terms of Cu removal obtained from the SHI-C material was significantly higher than that obtained with SHI-W, mainly due to the structural and chemical modifications after carbonate treatment. For each dose of this adsorbent, a percentage of recovery between 90 and 100% was achieved, independently of the pH value in the range 3–5. In the case of SHI-W, the highest values were between 60 and 75% and were both dependent on the pH and the dose used. SHI-C was also able to selectively remove 70% of copper in the presence of NaCl 1 M. The analysis of the isotherms indicated the presence of a complex adsorption mechanism that cannot be described by only one isotherm model.

Pd-ZnO nanoparticles decorated acid activated montmorillonite for the efficient removal of cationic dyes from water

Efficient adsorbent being the need of the hour for the effective removal of dye stuff from textile effluents, we herein report the synthesis of palladium intercalated zinc oxide nanoparticles decorated acid activated montmorillonite (Pd-ZnO@H+-Mt)nanocomposite using ion-exchange process followed by wet impregnation technique with Citrus limon leaf extract as reducing agent and its application as an efficient adsorbent for methylene blue (MB) and malachite green (MG) removal from water. The successful intercalation of Pd into the ZnO lattice was identified by band gap value calculated using UV-DR spectra. ATR FT-IR, XRD, SEM, TEM, TGA, BET, and XPS techniques confirmed the successful preparation of Pd-ZnO@H+-Mt nanocomposite. The synthesized Pd-ZnO@H+-Mt nanocomposite was then evaluated for efficient uptake of cationic dyes through batch adsorption experiments and thereby various parameters that influenced adsorption process were found. The experimental maximum adsorption capacity, qm of Pd-ZnO@H+-Mt for MB and MG dyes were 205 and 167 mg/g. The main driving force for the adsorption of MB and MG was identified to be the presence of mesopores, high specific area of Pd-ZnO@H+-Mt on acid activation, total pore volume and the presence of Pd-ZnO NPs on the surface which enhanced the negative charges of Mt surface thus facilitated better loading of dye molecules. Multilayer coverage of MB/MG molecules on Pd-ZnO@H+-Mt were evidenced through Freundlich isotherm model and experimental data of both MB and MG were described well by pseudo second-order kinetic model. The adsorption phenomenon was identified as feasible, spontaneous, and endothermic for MB adsorption while exothermic for MG adsorption. Moreover, the adsorbent could be recycled thrice. Thus, the synthesized Pd-ZnO@H+-Mt nanocomposite could be utilized effectively in industrial water treatment for the removal of dye stuff as adsorbent.

MOF@Cell: 3D printed biobased filters anchored with a green metal–organic framework for effluent treatment

Multifunctional, biobased materials applicable within water treatment industry, produced through additive manufacturing technology.