Water Spray System Research Articles

Planning And Installation of Water Spray System in The Underground for The Fire Hazard Prevention in PC. GKBI Production Unit

Fire is a serious risk that can cause great losses, both moral and material. This study evaluates fire prevention and control at PC. GKBI Medari, which recently experienced a major fire due to lack of fire detection. Using the AS/NZS 4360: 2004 method, nine hazards with high, medium, and low risks were found. In the underground area of the cambric factory, there are deficiencies in the existing fire extinguishing system, especially in dealing with invisible fires. Hot and dirty air is sucked and channelled through PVC ducts to the air filter, but this system is not effective in extinguishing fires. This study recommends the installation of water spray at several underground points to improve fire protection.

Improvement of aerosol spray scavenging efficiency by pre-injecting electrically charged water mist

Efficient aerosol scavenging is crucial for gas purification to reduce environmental pollution in various chemical industries. In nuclear reactor decommissioning, especially for damaged reactors after severe accidents like Fukushima Daiichi, controlling radioactive aerosol generation and dispersion is essential. Radioactive aerosols sizing from 0.1 to 1 μm are expected during containment cleaning and fuel debris retrieval processes. To ensure safe decommissioning and mitigate environmental radioactivity, a containment water spray system is used for aerosol scavenging. However, conventional water spray has low efficiency for these submicron aerosols. Our recent experiments at UTARTS demonstrated that pre-injection of water mist enhances scavenging efficacy by increasing aerosol size and hydrophilicity through aerosol-mist agglomeration prior to spraying. On this basis, in this study, we introduced an innovative method using electrically charged water mist, which significantly facilitates aerosol-mist agglomeration through additional electrostatic coagulation, further improving scavenging efficacy (maximum 35 % in current configurations). The present experimental results attained under various mist conditions and charging configurations provided insights into optimizing the mist charging system. Our developed technology is expected to be useful in radioactive aerosol control during damaged reactor decommissioning and has potential applications in other environmental chemical engineering processes.

Rancang Bangun Kontrol Pemadam Kebakaran Menggunakan Sensor MQ-2 dan Flame Sensor 5 Channel Berbasis Fuzzy Logic

Fire is an event that often occurs due to human negligence. Losses from fire include damage to goods, business delays and can even cause loss of life. For early handling of fires, a "Fire Fighting Control Design Using MQ-2 Sensor and Fuzzy Logic Based 5 Channel Flame Sensor" has been created. This tool uses the MQ-2 sensor to detect gases related to fires, such as hydrocarbon gas. A 5 channel flame sensor is used to detect flames. The predetermined fuzzy logic rules will be used to control the fire extinguisher and implemented using the Arduino Atmega 2560 microcontroller as the brain of the system. Next, the microcontroller will send a control signal to the 12V DC pump output as a water spray system to deal with fires. The test results of this system show that the tool can detect early fire hotspots and respond well to fire extinguishing according to the fuzzy rule decisions carried out by testing the tool with 30 fire spots at different distances.

Strategies, challenges, and outcomes of heat stress resilience in sub-Saharan African community-based cattle feedlots: a systematic review.

In sub-Saharan Africa, cattle feedlots face a significant challenge in dealing with heat stress. However, there is a lack of inclusive strategies for resilience in these situations. The aim of this systematic review is to investigate the strategies, challenges, and outcomes related to heat stress resilience in community-based cattle feedlots in sub-Saharan Africa. The PRISMA approach, which is a method for reporting systematic reviews and meta-analyses, was used to identify, screen, and analyze 30 peer-reviewed articles published over the last 20 years from Google Scholar and Scopus. The review found that key strategies to mitigate heat stress include providing shade through natural and artificial means, ensuring constant access to cool, clean water using water spraying systems and cooling ponds, and implementing nutritional adjustments such as high-energy feeds and electrolyte supplements. Additionally, genetic selection for heat-tolerant breeds and management practices like adjusting feeding times and improving ventilation were found to be effective in dealing with heat stress. In particular, local germplasm and genetic traits of cattle in sub-Saharan Africa play a crucial role in heat stress resilience. Indigenous breeds, which have adapted to the region's harsh climate over centuries, exhibit traits such as higher heat tolerance, better water-use efficiency, and improved feed conversion rates under heat stress conditions. This genetic resilience can be enhanced through targeted breeding programs aimed at amplifying these beneficial traits. Implementing these strategies resulted in improved cattle health and productivity, as evidenced by enhanced weight gain, better reproductive performance, and lower mortality rates. The socio-economic benefits of these strategies included reduced economic losses and increased farmer incomes, which in turn contributed to improved community health and nutrition. However, the review also identified significant challenges, including financial constraints, limited access to knowledge and training, and cultural resistance. To address these barriers, the review recommends increased investment in affordable cooling technologies, farmer education, and community-based initiatives. Additionally, leveraging the genetic strengths of local cattle breeds should be prioritized to maximize the effectiveness of heat stress resilience strategies.

Effect of physicochemical properties on critical sinking and attachment of respirable coal mine dust impacting on a water surface

Respirable coal mine dust (RCMD) inhalation is identified as the main cause of the resurgence of coal worker’s pneumoconiosis (CWP) since the mid-1990s. At present, the predominant dust control technology is the water spray system. However, in practice, the capture efficiency of RCMD by this technology is relatively low. To understand the capturing mechanism and develop improvement strategies, this research is focused on the surface chemistry study of RCMD and its impact on a water surface using a dynamic model. Proximate analysis, chemical, and mineral composition of a run-of-mine (ROM) coal sample from Appalachian region were analyzed using a proximate analyzer, Inductively Coupled Plasma Mass Spectrometry (ICP-MS), and X-ray Diffraction (XRD), respectively. Contact angles were measured by capillary rise test using the Washburn equation. Based on the dynamic model, the effects of particle size, density, contact angle, and surface tension on the critical sinking were investigated. It was pointed out in this work that reducing surface tension, in turn, decreases contact angle, which has been neglected in the literature. Regime maps for different minerals were created and showed that organic matter has the highest critical velocity due to its low density and high contact angle. Reducing water surface tension to the critical solid surface tension of coal around 30 mN/m could maximize the attachment efficiency. Scaling laws, constructed by force balance, led to the criteria of critical sinking: Ucr∼61-cosθ2D+1γlvρlR, i.e., Wecr∼121-cosθ2D+1. A semi-empirical formula for critical velocity was obtained by fitting the simulation data, Ucr=1.0961-cosθ2D+1γlvρlR. Attachment efficiency was defined and formulated as Pa=U02Ucr2=We0Wecr, establishing relationships between attachment efficiency and the physicochemical properties of RCMD and water droplets.

Experimental study on fire extinguishing performance of typical large space fires on ships

ABSTRACT A reliable fire extinguishing system is an effective measure to reduce the risk of ship fire. Based on a typical large space cabin platform, the experiments on the fire extinguishing performance of different fire extinguishing systems (high-expansion foam, aqueous film-forming foam and water spray) against oil pool fire (6 MW) and wood stack fire (0.3 MW) were carried out. The results show that for oil pool fire, the fire extinguishing performance of aqueous film-forming foam system is higher than that of high-expansion foam system. The fire extinguishing performance of high-expansion foam system is significantly affected by the relative location of high-expansion foam generator, fire source and obstacle. For wood stack fire, the fire extinguishing performance of water spray system is the best, and the fire extinguishing time is only 25 s, followed by the aqueous film-forming foam system (54 s) and the high expansion foam system (66 s).

Solar Panel Cleaning System with Voltage Drop Detection

bstract: This research suggests a unique voltage drop sensor and LDR (light-dependent resistor) based solar panel dust removal detecting system. Whereas the voltage drop sensor gauges the voltage differential between the solar panel's input and output, the LDR sensor counts the amount of light reflected from the panel's surface. The system is able to precisely identify the existence of dust and assess its level of intensity by evaluating the aggregated data from these sensors. Afterwards, an automatic dust removal device, like a water spray system or robotic brush, can be started using this information. The suggested method improves the overall performance and lifespan of solar photovoltaic systems by providing an automated, economical, and efficient alternative for the removal of dust from solar panel

Autonomous Vehicle for Fire detecting and Extinguishing

— Our project presents an innovative solution for fire detection and extinguishing through an autonomous rover system. Leveraging fire sensors integrated with a node MCU, the system swiftly identifies fire outbreaks and transmits alerts to the rover via the ThingSpeak cloud platform. Upon receipt of the alert, the rover activates a buzzer for immediate local notification and dispatches alerts through a dedicated mobile application, ensuring rapid response from relevant personnel. Employing a line follower mechanism, the rover autonomously navigates towards the fire-affected area. Equipped with a water spraying system, the rover efficiently extinguishes flames, minimizing water wastage and enhancing firefighting effectiveness. This approach significantly reduces response time, enhancing safety across diverse environments. The system's ability to optimize resource utilization and automate firefighting procedures makes it adaptable to various settings, including industrial facilities, urban areas, and remote locations. Overall, our autonomous rover system represents a substantial advancement in firefighting technology, offering swift and efficient fire detection and extinguishing capabilities to mitigate fire hazards effectively. Keywords— NodeMCU, Rover, Flame Sensors, Servomotor, L293d motor drivers, Li-ion batteries

REAL TIME WIRELESS FIRE FIGHTING ROBOT

The Real-time Wireless Firefighting Robot is an innovative autonomous robotic system designed for effective fire response in hazardous environments. This robot integrates advanced technologies such as wireless communication, sensors, and real-time data processing to enhance firefighting capabilities. Equipped with a high-resolution camera, the robot can navigate through smoke-filled areas and transmit live video feeds to the control center. The wireless communication system enables seamless remote operation, allowing firefighters to assess the situation and make informed decisions. The robot's robust design and fire-resistant materials ensure its durability in high-temperature environments. Overall, the Live Wireless Firefighting Robot presents a cutting-edge solution for improving firefighting efficiency and reducing risks to human responders. This robot is equipped with advanced sensors for real-time fire detection and localization. Its wireless connectivity enables remote control and monitoring, allowing firefighters to operate it from a safe distance. The robot's mobility and agility enable it to navigate challenging environments, reaching areas that may be hazardous for humans. With a built-in water or foam spraying system, the robot can effectively suppress fires. Additionally, it incorporates live video streaming to provide a comprehensive view of the situation. The use of wireless technology not only facilitates seamless communication but also ensures quick response times, making this robot a valuable asset in firefighting scenarios, minimizing risks to human lives. Key Words: Fire Fighting Robot, Mobility, Live video feeds.

Enhancing the vaporization and secondary atomization of two-liquid droplets for fire suppression

Large-scale fires of various origins are most often contained and suppressed using fine water spray systems with a droplet size of 50–300 μm. Enhancing the extinguishing performance of these systems is an urgent task as this will reduce the amount of irreversible damage fires cause to forests, buildings, and compartments. Finer droplet size of the extinguishing liquid sprayed directly in the combustion zone prevents droplet entrainment, thus increasing the firefighting efficiency and reducing the extinguishing liquid consumption. However, too little is still known about alternative ways to intensify the vaporization and secondary atomization of fine water sprays in order to disrupt the chemical reactions responsible for combustion. Experimental findings on enhancing the secondary atomization and phase change of sprayed water with added vegetable oils for fire suppression are presented. Experiments on water droplets with sunflower, rapeseed, and tall oils were performed in the ethanol burner flame zone. The radii of two-liquid droplets were 0.85 ± 0.05 mm. The concentration of explosion-triggering additives to water was constant at 10 ± 2 vol.% in all the experiments. The addition of 10 vol.% rapeseed oil to water allows one to reduce the local gas temperature around the droplet up to 250 K in case of micro-explosion of an isolated droplet and up to 450 K in case of micro-explosion of a group of droplets. The experimental findings were processed to obtain approximations of the relationships established in the experiments: micro-explosion delay times, droplet lifetimes, and normalized evaporation surface area after breakup. A physical model is presented describing the processes involved in the experiments. An additional series of experiments involved suppressing a laboratory-scale wood crib fire using water and water/rapeseed oil emulsion to compare the fire suppression times and the extinguishing liquid consumption in both cases. The suppression times and the extinguishing liquid consumption were on average 15% lower when using a water/rapeseed oil emulsion compared with pure water. Practical recommendations are given on how to provide the intense disruption of extinguishing liquids with added vegetable oils to accelerate fire suppression. Two-liquid droplets exploding in the flame zone are established as a possible alternative to water capsules, extinguishing missiles, and cryogenic technologies for suppressing large-scale fires.

The Development of Automatic Sprinkler System Concepts for Maritime Vehicle Carriers

Closed ro-ro spaces on maritime vehicle carriers are usually protected by a total-flooding carbon dioxide system. Such systems have many benefits, for example that there are no residues that can adversely affect the protected objects (in this case thousands of vehicles) and the agent is electrically non-conductive. However, there could be a considerable time delay from the start of a fire until the carbon dioxide system is discharged. Experience has shown that this delay time can cause significant fire damage and jeopardize the performance of the system. Within the EU funded LASH FIRE project, design and installation guidelines for supplementary automatic water-based fire sprinkler systems were developed. An important design feature is that the system automatically activates at an early stage of a fire. This would allow more time to fight the fire manually or to safely evacuate the space and discharge the CO2 system when the fire is controlled to one or a few vehicles instead of at a time when it has escalated in size. The work was partly based on a comprehensive literature review that identified relevant standards and information applicable to the design of automatic fire sprinkler and deluge water spray systems. Large-scale fire tests verified that the suggested system designs were able to provide control of realistic vehicle fires, including fires in passenger cars and a freight truck.

Molecular simulation study of the influence of different surfactants on the wetting characteristics of anthracite

The reduction of dust pollution in coal mines is of great importance both for protection of the environment and for the occupational safety and health of coal mine workers. The reduction of dust from anthracite has been a challenge due to its inherent hydrophobicity and high metamorphism. As a result, surfactants are commonly added to water to improve the wettability of coal, thereby improving the dust reduction efficiency of a water spray system. To clarify from a microscopic perspective the effect of different surfactants on the wettability of anthracite, models for the anthracite-surfactant-water system were established, and adsorption configuration, relative concentration distribution, and the diffusion coefficients of water molecules in the systems were thoroughly investigated with molecular simulations. The results showed the directional arrangement of surfactants in the simulation systems after 150 ps of equilibration, resulting in the reduced surface tension of the water-surfactant solution and enhanced wettability of anthracite. Along the (001) normal direction, the relative concentration of sodium dodecylbenzenesulfonate (SDBS) (15.32), the anthracite-water overlapping area, the diffusion rate of water molecules, and the activity (DSDBS = 0.97 × 10-8 m2·s−1) were maximized, indicating the excellent wettability effect of SDBS. The results of the study are of practical significance for improving the wetting effect of anthracite, improving the dust reduction efficiency, and safeguarding the occupational safety and health of personnel.

Preliminary design of the suppressive containment system based on HPR1000

The current HPR1000 has a high construction cost and weak economic competitiveness due to its complex system and large containment. This study proposes a conceptual design of an advanced containment system based on HPR1000, which aims at reducing the construction cost of nuclear power plants without reducing their safety. In the design, the In-containment Refueling Water Storage Tank (IRWST) and spray system were discarded, and the space of the double containment vessel was used to create an annular cavity pool (ACP). The transient pressurization in the containment caused in the early stages of the accident can be quickly suppressed by ACP instead of the traditional large-volume suppression concept. And due to the significant condensation of steam within the ACP water, the transportation of air into the ACP results in a reduction in the air mass fraction in the vicinity of the passive containment heat removal system (PCHR) located within the containment structure. This phenomenon subsequently leads to an enhancement in heat transfer performance. In addition, ACP also serves as the water source for the safety injection system, the reactor cavity water injection system, and the core replacement system. Compared with HPR1000, the system of the preliminary design has been greatly simplified, and the size of the containment vessel has been reduced by nearly 47%. The simulation of the large-break loss-of-coolant accident (LBLOCA) scenario has been conducted to examine the response of the containment system, specifically focusing on the performance of the safety injection system and suppression system. The results show that the integrity of the containment and core was ensured throughout the accident, and there was a safety margin.

Thermal Hydraulics Simulation of a Water Spray System for a Cooling Fluid Catalytic Cracking (FCC) Regenerator

Olefins are crucial building blocks for petrochemical industry, serving as raw materials for the production of various products such as plastics, synthetic fibers, detergents, solvents, and other chemicals. In FCC, heavy petroleum feedstocks are injected into a catalytic cracking unit, where they are mixed with a catalyst. The catalyst aids in breaking down the large hydrocarbon molecules into smaller fragments, including olefins like Propylene and Ethylene. These polymerization reactions occur at high temperatures. They demand that heat removal occurs as quickly as possible in order to control the reactor temperature and to avoid “hot spots” in the Regenerator or localized oxidation reactions (and to avoid creep rupture of the regenerator steel cladding). The cooling of the regenerator cladding surface can be achieved by impinging water droplets (spray), ejected from a spray nozzle. Spray cooling can provide uniform cooling and handle high heat fluxes in both a single phase and two phases. This research provides a thermal hydraulic design of regenerator spray cooling systems. In the framework of this research, Fire Dynamics Simulator (FDS) software was applied in order to simulate the temperature field and the water vapor mass fraction. A COMSOL Multiphysics finite element code was used in order to calculate the temperature field inside the regenerator cladding. The calculated surface temperatures and heat transfer convective coefficient, obtained using FDS software, were validated successfully against COMSOL numerical results and previous results in the literature. The numerical simulations were carried out for two cases. The first case was carried out at a distance of 0.5 m, and the second case was carried out at a distance of 0.2 m. A grid sensitivity study was carried out on the FDS model. Numerical integrations were carried out over time in order to calculate the average temperatures. The difference between these four average temperatures, calculated by applying different grids, is less than 7.4%. The calculated surface temperatures and heat transfer convective coefficient were validated successfully against COMSOL numerical results and previous research. It was shown that the calculated temperatures decrease in the second case. The water spray system managed to cool the steel wall more effectively as the water spray system approaches the steel cladding.

Water spray effects on fire smoke temperature distribution beneath a symmetrical V-shaped tunnel ceiling

The coupling effects of the double-slope stack effect, the thermal buoyancy induced by the V-shaped tunnel fire and the drag force generated by the water spray system alter fire smoke flow regulation compared to fire smoke flow in a horizontal tunnel. By numerical simulation, this work investigates the effect of water spray flow rate (0 L/min – 600 L/min), atomization angle (0–150°) and the length within fire source and the grade change point (0–120 m) on smoke temperature distribution beneath a symmetrical V-shaped ceiling. The findings indicate that the cooling effect on smoke temperature can be significantly improved by increasing the rate of water spray flow, while water spray increasing angle and tunnel slope have little contribution to the cooling smoke temperature. Thus an improved ceiling smoke temperature distribution model is proposed by importing the flow rate, angle coefficients and tunnel slope. As the fire source distance from the grade change point increases, stack effect on fire smoke flow could be categorized into three zones, which are the double-slope control zone, the transition zone and the single-slope control zone, which causes that downstream smoke temperature become higher gradually than the upstream one, while the smoke temperature difference tends to stabilize at the single-slope control stage. Finally, a global ceiling smoke temperature distribution in the symmetrical V-shaped tunnel installed a water spray system is established by introducing fire source distance coefficients.

High-Speed Laser Drilling for Dental Implantation: Ablation Process and Applicator Technology

Abstract Conventional mechanical drilling for implant placement is limited to specific geometry and orientation, resulting in incorrect positioning and inadequate anchoring in thin or porous bone. This study presents the development of a laser-based ablation process and an applicator technology for precise and fast laser drilling in the oral cavity. For the process development, a CO2 laser with a wavelength of 10.6 μm was used. Pulse durations between 10 μs and 400 μs were investigated for fast laser drilling with low thermal impact. For efficient ablation and cooling of the bone tissue, we applied a fine water spray. The laser applicator is designed with an integrated scanning module, focusing optics and a compact water spray system with three spray nozzles in the applicator tip. The geometry of the cavities was analyzed using digital microscopy and scanning electron microscopy, allowing to measure the ablated volume and depth as well as investigating the bone microstructure. This study demonstrates a laser ablation process capable to generate cavities with an ablation rate of 1.75mm3/s which is about 80% higher than previously reported. At this ablation rate the melted zones were smaller than 30 μm. This paper demonstrates a concept for a dental laser drilling system with a fast ablation process and a highlyintegrated applicator for treatment in the oral cavity.

A comprehensive evaluation of water spray system on transparent roof towards optimal operation schedule

Indoor overheating induced by transparent roofs sharply increases the building energy consumption. Water spray offers a potential solution but requiring effective strategy to balance cooling effects and cost-effectiveness. Aiming at a spray system installed on transparent roof (63.2 × 24.6 m) of a mixed-use building in Guangzhou, China, this study provides a comprehensive evaluation of multiple strategies including continuous and intermittent operation with different spray/interval time. In sunny weather, continuous spray reduces the exterior, interior surface temperature, and long-wave radiation by 17.5 °C, 9.6 °C, and 66.3 W/m2, respectively. Besides, the indoor air temperature, globe temperature, and mean radiant temperature are also lowered by 4.4, 5.2, and 5.7 °C, respectively. Comparatively, the intermittent spray produces worse cooling effect, the reduction of exterior, interior surface temperature, and long-wave radiation are 9.4–15.9 °C, 4.1–7.8 °C, and 24.1–47.7 W/m2, respectively. The intermittent operating conditions, sorted according to the exterior surface temperature reduction, are ranked as 30/10 > 20/10 > 10/10 > 10/50 > 10/20 min, with the cooling effect not decreasing linearly with interval time, but increasing monotonically with spray time. The air conditioning electricity saved by continuous spray is higher than that by intermittent spray, but the water pump electricity and water consumptions are higher as well. Technical-economy evaluation indicates that water consumption is primary cost factor in spray systems and intermittent spray with 10/50 min is the optimal scenario. This study provides insights into the economical and efficient operation of transparent roof spray system, and lays a foundation for its smart control.

Improving the performance of indirect evaporative cooler for energy recovery from the perspective of nozzle configuration: A CFD model analysis

As a sustainable cooling technology, indirect evaporative cooling (IEC) has been widely recognized as an effective means of achieving carbon neutrality based on its low energy consumption and high efficiency in central air conditioning (AC) systems of buildings. In contrast to the conventional arrangement, IECs as heat recovery units are often arranged in a diamond shape inside the air handling units (AHUs) of data centers (DCs), an approach that facilitates the flexible use of space and integration within the units in a more compact form. The use of CFD simulations allows an integrated analysis of the coupling of hydrodynamic, thermal and mass properties helps to improve the evaporation performance of IECs. In this study, a 3D simulation model of a diamond-shaped IEC containing the water spray system was developed to compare and analyze the air-water arrangement options in IEC systems currently used in DCs, and the corresponding characteristics are explored from the perspective of CFD techniques to determine the effect of nozzle configurations on the formation and evaporation of water film within the wet channels. Then, parametric analysis of nozzle setup schemes based on performance metrics showed that the nozzle arranged in top-side configuration and paired with the air-water counterflow form had the best performance, with 59.2% and 27.4% improvement in water film coverage area and temperature drop, respectively, over the worst scheme (bottom configuration) at a water supply flow rate of 65 L/s. Finally, the effectiveness of the enhanced approach was simulated and analyzed for hydrophilic and fiber coatings, and it was found that the water film coverage increased by 14.5% and 31.6%, respectively, while the coefficient of performance (COP) increased by 7.4% and 16.1%.

Experimental evaluation of a water spray system for semi-outdoor spaces: Analysis of the effect of the operational parameters

As a consequence of climate change, urban overheating has increased in all the cities of the world during the last decades. It is therefore paramount to counteract such effect by promoting the use of effective solutions to mitigate overheating at a micro-scale level. In this work, a modular experimental setup based on a water spray system was designed, realized and tested to evaluate its thermohygrometric performance in semi-outdoor spaces such as bus/train/taxi stops, street resting stations and corner shops. The setup allows to vary three operational parameters: (a) the height of the nozzles from the ground; (b) the presence of an upper shielding to reduce the impact of solar radiation; (c) the presence of a side shielding to reduce the impact of wind speed. The combination of the operational parameters allowed to evaluate the performance of five configurations for the water spray system. Several performance indexes were calculated to assess the impact of each operational parameter. It was found that the best configuration guarantees a −20% reduction of dry-bulb temperature, and the minimum specific water and electricity consumptions of the system are 0.020L/m2 and 0.150Wh/m2, respectively. Also, the presence of the side shielding is the parameter that mostly influences the performance of the system, followed by the height of the nozzles, while the presence of the upper shielding has a minor effect. These operational parameters, however, increase relative humidity inside the nebulization volume; it is therefore important to verify if undesired wet conditions are reached.

Indoor Fire Simulation in Low-Rise Teaching Buildings Based on BIM–FDS

School buildings gather a large number of underage students, and the disastrous consequences of fire in such buildings are very serious, which is one of the key concerns of society in fire prevention and control. This study takes a “[” type kindergarten teaching building as the background and constructs a BIM–FDS building fire simulation model to reveal the fire smoke dispersion law under the coupling of the typical building structure and fire protection systems. The results show that the stairwells on both sides of the “[” type building are the main channels for the diffusion of fire smoke, and the asymmetry of the stairwell structure will cause apparent differences in the diffusion of smoke. Using the natural smoke exhaust in the stairwells of low-rise buildings does not aggravate the spread of smoke in the building and is conducive to smoke emissions. The high-pressure water mist system is superior to the water spray system in fire extinguishing and controlling room temperature. While it reduces smoke exhaust performance, it does not adversely affect personnel evacuation. This study systematically reveals the law of diffusion of fire smoke from “[”-type teaching buildings, which can support the design of similar building structures, ventilation, fire protection, and the formulation of fire escape plans.