Water Mist Suppression Research Articles

The Effects of Droplet Size and Injection Orientation on Water Mist Suppression of Low and High Boiling Point Liquid Pool Fires

This paper presents the results of an experimental parametric study of water mist suppression of large-scale liquid pool fires. The experiments were conducted with 50cm diameter pan heptane and JP8 pool fires. Mist was injected into the fire from the base at 90° and 45° and from the top at 90°. The results show that base injection of droplets enhanced their suppression effectiveness by as much as two times. Secondly, optimum suppression effectiveness is obtained with small droplets injected at the base of the fire. This is because the droplets evaporated quickly within the lower region of the fire where a greater effect of oxygen dilution and water vapor higher heat capacity is fully realized. Finally, a comparison of the results with the two fuels show that water mist is more effective in suppressing the JP8 fires than the heptane fires. It is concluded that the additional effects of direct surface cooling contributed significantly to the observed difference.

The Development of a CFD Based Simulator for Water Mist Suppression Systems: The Development of the Fire Submodel

The FIRE Detection and Suppression Simulation (FIREDASS) project was concerned with the development of water misting systems as a possible replacement for halon based fire suppression systems currently used in aircraft cargo holds and ship engine rooms. As part of this program of work, a computational model was developed to assist engineers optimize the design of water mist suppression systems. The model is based on Computational Fluid Dynamics (CFD) and comprised of the following components: fire model; mist model; two-phase radiation model; suppression model; detector/activation model. In this paper the FIREDASS software package is described and the theory behind the fire and radiation sub-models is detailed. The fire model uses prescribed release rates for heat and gaseous combustion products to represent the fire load. Typical release rates have been determined through experimentation. The radiation model is a six-flux model coupled to the gas (and mist) phase. As part of the FIREDASS project, a detailed series of fire experiments were conducted in order to validate the fire model. Model predictions are compared with data from these experiments and good agreement is found.

Simulation of water mist suppression of small scale methanol liquid pool fires

The focus of this paper is on numerical modeling of methanol liquid pool fires and the suppression of these fires using water mist. A mathematical model is first developed to describe the evaporation and burning of liquid methanol. The complete set of unsteady, compressible Navier–Stokes equations are solved along with an Eulerian sectional water mist model. Heat transfer into the liquid pool and the metal container through conduction, convection and radiation are modeled by solving a modified form of the energy equation. Clausius–Clapeyron relationships are invoked to model the evaporation rate of a two-dimensional pool of pure liquid methanol. The interaction of water mist with pulsating fires stabilized above a liquid methanol pool and steady fires stabilized by a strong co-flowing air jet are simulated. Time-dependent heat release/absorption profiles indicate the location where the water droplets evaporate and absorb energy. The relative contribution of the various suppression mechanisms such as oxygen dilution, radiation and thermal cooling is investigated. Parametric studies are performed to determine the effect of mist density, injection velocity and droplet diameter on entrainment and suppression of pool fires. These results are reported in terms of reduction in peak temperature, effect on burning rate and changes in overall heat release rate. Numerical simulations indicate that small droplet diameters exhibit smaller characteristic time for decrease of relative velocity with respect to the gas phase, and therefore entrain more rapidly into the diffusion flame than larger droplet. Hence for the co-flow injection case, smaller diameter droplets produce maximum flame suppression for a fixed amount of water mist.

99/02705 Some simple considerations on the turbulent mixing process in relation to flame-scaling

Froude-based scaling relationships had previously been theoretically extended to, and experimentally validated in the laboratory for, water mist suppression of fires in open environment and in enclosures, which were shown applicable to gas, liquid and solid combustible fires. Before applying these relationships to real-world settings, their applicability needs to be further evaluated for the intended protection. This paper presents such an evaluation on scaling water mist fire extinguishment in an industrial machinery enclosure. In this evaluation exercise, a full-scale water mist protection set-up tested for a 260-m3 machinery enclosure was selected as the benchmark. A ½-scale machinery enclosure test replica was then constructed, together with a ½-scale nozzle whose orifices were geometrically similar to those of the full-scale nozzle. Spray measurements indicated that the ½-scale spray closely met the scaling requirements, in terms of discharge K-factor, water mist flux, droplet velocity and droplet size distribution. Two spray fires and one pool fire, which were scaled with the respective full-scale fires, were used to challenge the water mist protection in the ½-scale enclosure. At least five replicated tests were conducted for each of the four tested fire scenarios. Overall, the instantaneous local gas temperature and oxygen concentration measured inside the ½-scale enclosure for each fire scenario agreed reasonably well with those measured at the corresponding locations inside the full-scale enclosure, meeting Froude modeling's requirement that scalar quantities be preserved in different scales. The fire extinguishment times obtained from the ½-scale tests for each fire scenario were also statistically consistent with that observed in the corresponding full-scale test. Based on the obtained results, it is concluded that, for machinery enclosures and other similar occupancies, the previously laboratory-validated scaling relationships for water mist fire suppression can be used to determine the fire extinguishing performance of a full-scale water mist protection in a ½-scale test facility.