Water Load Research Articles

Design of Integrated Energy–Water Systems Using Automated Targeting Modeling Considering the Energy–Water–Carbon Nexus

The swift expansion of the global population and economy has spurred growing requirements for energy and water in recent decades. Inefficient energy and water consumption, however, has led to an increase in CO2 emissions. Hence, the socio-economic development of a country must consider the interconnections between energy, water and carbon, as there are mutual dependencies among these three elements. This work considers the nexus between energy, water and carbon in the design of integrated energy–water systems using a new automated targeting modeling (ATM) framework. ATM incorporates the advantages of the insight-based Pinch method and a mathematical programming approach to provide visual understanding for a thorough analysis of the problem while guaranteeing accurate solutions. Minimum targets of power and water based on the integrated network operation were established by the ATM, with corresponding carbon emissions. A specific goal of annual carbon emissions reduction was set as the constraint and the ATM optimized the capacities of the components in the system accordingly to achieve minimum overall cost. The application of ATM on an industrial plant case study shows that a target of 45% reduction in the carbon discharge amount was achieved by shifting to greener fuel in the energy system at a minimum overall cost increase of 0.45% only. The framework can assist users in meeting power and water loads in their plant while planning for the appropriate decarbonization efforts at the minimum possible cost.

Probing the friction mechanism of diamond-like carbon films in aqueous environments based on molecular dynamics simulations

Abstract The frictional behavior of diamond-like carbon (DLC) films in an aqueous environment is of tremendous interest. To compare the impacts of the quantity of water molecules, sliding velocity, and loading on the friction behavior of DLC films, a molecular model of DLC films in an aqueous environment was built. The results show that the DLC film under high load and high sliding velocity leads to severe friction behavior, but the water molecules can prevent the occurrence of this severe friction behavior. Also increasing the number of water molecules can effectively reduce the increase in friction during the running-in stage and keep it at a low value. The primary explanation is that if there are enough water molecules, they will create a stable water film at the friction interface and prevent large-scale contact and distortion between the upper and lower DLC films, significantly reducing friction.

Drowning Prevention should be a Public Health Issue in Nepal

Nepal is prone to a range of natural disasters; earthquakes being the most widely recognised one. However, many people are at risk of drowning as the floodings in the autumn of 2024 showed, but this is not recognised enough as a serious public health risk in Nepal. Drowning relates to everyday activities such as bathing and swimming and should be treated as a social and public health problem. The United Nations, particularly the World Health Assembly, has called its member states for accelerating action on drowning prevention. This mini review paper considered literature covering drowning in children in Nepal and Bangladesh over the past decade. It outlines some of the key drowning risks and the need for active prevention with reference to some tested drowning prevention interventions in neighbouring countries in South Asia. Many of such interventions have been designed and implemented in Bangladesh, a densely populated countries with a load of water. It has one of the highest rates of drowning, especially among children in the world. Next, the paper highlights some on-going research in this field, especially our newly started research project in Bangladesh, which is aimed at the prevention of drowning in children under two. Finally, the paper concludes with some of the lessons Nepal can learn in this area from its neighbours.

Nature of Reactive Sites in TS-1 from 15N Solid-State NMR and Ti K-Edge X-Ray Absorption Spectroscopic Signatures Upon Pyridine Adsorption.

Ti-containing zeotypes, notably titanosilicalite-1 (TS-1), are prominent examples of heterogeneous catalysts that have found applications in selective oxidation processes with hydrogen peroxide. Despite extensive characterization studies including using various probe molecules to interrogate the nature and the local environment of Ti sites, their detailed structure (as well as reactivity) remains elusive. Here, we demonstrate that using low temperature 15N magic angle spinning (MAS) ssNMR spectroscopy of adsorbed pyridine on TS-1 combined with Ti K-edge XANES on a range of samples (dehydrated, hydrated, contacted with H2O2 and pyridine) provides unique information regarding the Ti sites, highlighting their reactivity and dynamic nature. While dehydrated TS-1 shows only Lewis acid sites, the presence of H2O generates Brønsted acid sites, whose amount correlates with water loading. Moreover, the methodology─based on 15N ssNMR and Ti K-edge XANES─applied to a library of samples with various Ti-loadings and absence of extraframework TiO2 also enables quantification of the amount of Lewis acid sites and to establish a structure-activity descriptor (ratio of pyridine adsorbed on silanols vs titanium). Complementary analysis including computational modeling reveals that the reaction of Ti sites with H2O generates an acidic bridging silanol Ti-(OH)-Si, upon hydrolysis of one Ti-O-Si linkage, where Ti expands its coordination from four to pentacoordinated according to XAS.

Passive Inclination Sensor Based on a Patch Antenna with a Reconfigurable Water Load.

In order to ensure the safety and preserve the value of historical buildings, inclination is an essential parameter during the continuous structural health monitoring process. However, the wire and price of a traditional sensor limit application. This paper proposes a low-cost inclination sensor based on a patch antenna with a reconfigurable water load. Only the water directly on the antenna is considered effective. The different volume of the effective water load, which is determined by the inclination of the attached surface, will affect the effective permittivity of the dielectric plate of the patch antenna, further causing a variation in the resonant frequency. Therefore, the proposed antenna sensor can monitor the inclination of the attached surface by interrogating the resonant frequency. The working mechanism is first clarified by theoretically investigating the relationship between the dielectric properties and the inclination of the covering medium. The antenna sensor is then simulated using High-Frequency Structure Simulator ver.15 (HFSS 15), which helps to determine geometric parameters and confirm accuracy and sensitivity. An experiment has been conducted based on the design verified in the simulation. The inclination detection shows a correlation coefficient of 0.9771 with a sensitivity of 7.92 MHz/°, indicating a potential for real application.

Efficient sulfur accumulation in biological desulfurisation and denitrification induced by microbial and chemical interactions

ABSTRACT Efficient accumulation of sulfur from simultaneous desulfurisation denitrification process can achieve high economic and environmental benefits. This work aims to study the effect of product accumulation on elemental sulfur production and understand its potential mechanism. The addition of the intermediate product thiosulfate and the final product sulfate during the reaction led to an increase in the production of biological elemental sulfur ( S bio 0 ). The effect is mainly reflected in the efficient accumulation effect of S bio 0 at high sulfide loads. When the sulfide feed water load was 300 mg/L, the S bio 0 production reached 65.94 mg/L in 24 h with the addition of 30 mg/L thiosulfate and 20 mg/L sulfate, which was 3.11 times higher than that of the control group. The addition of sulfate increased the content of aromatic protein I and aromatic protein II, and accelerated the propagation of Thiobacillus denitrificans, whose viable bacterial amount was 1.12–2.98 times higher than that of the control group. On the one hand, low-dose sulfate induced Thiobacillus denitrificans to participate in the sulfur-producing reaction ( S 2 − → S bio 0 ) more quickly by accelerating the propagation of the strains in the pre-reaction stage. On the other hand, the addition of sulfate shifted the overall reaction equilibrium to the left and inhibited the formation of thiosulfate, thus accelerating the accumulation of S bio 0 in the whole reaction stage. This study would provide guidance for artificially promoting efficient sulfur accumulation in desulfurisation denitrification treatments.

Simulation of lunar soil compressive strength performance test based on grey correlation analysis

Detecting water ice in the permanent shadow area of the lunar south pole is an important task of China's Chang'e-7. For this purpose, a simulation study was carried out under the earth environment, and a test sample of polar water-containing simulated lunar soil was prepared. The mechanical properties of the lunar soil simulant were tested under ultra-low temperature conditions, and the changes in water content, relative density, temperature, loading rate, and base material ratio with compressive strength were analyzed. The results show that the compressive strength of the frozen lunar soil simulant increases with the increase of water content, increases with the increase of density, and increases with the decrease of temperature. It is less affected by the change of loading rate. The order of compressive strength affected by different base material ratios is: 100%anorthosite, <90%anorthosite, +10%basalt <70%, +30%anorthosite <100%, basalt, lunar soil simulant. Finally, the correlation between the basic physical properties of lunar soil simulant such as water content, relative density, temperature, loading rate, and ratio and compressive strength is explored through grey correlation analysis. The correlation order is: water content> density> temperature> ratio> loading rate. This paper prepared and tested the mechanical properties of hydrated lunar soil, and proposed a more systematic and standardized implementation plan. It serves as the basis for studying the properties of hydrated lunar soil in the polar region, and provides a theoretical basis and reference for subsequent lunar soil simulation research.

Dynamic tensile characteristics of an artificial porous granite under various water saturation levels

Underground rocks are generally subjected to water erosion and dynamic disturbances. To exclude the effect of clay minerals on the water–rock interaction mechanism, clay-free artificial porous rock (APR) was used to investigate the coupling effect of water saturation and loading rate on tensile behavior. Dynamic Brazilian disc experiments were performed on APR with six water saturation levels (100, 80, 60, 40, 20, and 0%) using a split Hopkinson pressure bar (SHPB) combined with a high-speed camera. The results indicated that the number of cracks in the APR specimens increased with the water saturation level during the dynamic damage process, with more radial cracks at the water saturation of 80–100%. The dynamic tensile strength (DTS) and dissipated energy density exhibited different change trends with water saturation levels under different loading rates and the rate dependence was most significant in the fully saturated state (100%). At lower loading rates, DTS initially decreased rapidly and then more slowly with increasing water saturation. At higher loading rates, DTS exhibited a ‘decrease then increase’ trend. Moreover, the water-affecting factor exhibited an overall decreasing trend with the loading rate and gradually converged to 1.0. These phenomena can be attributed to the interplay between the weakening and strengthening water-effect mechanisms based on the microstructure and water distribution in the APR specimens.

Mesoporous Silica Microparticle-Protein Complexes: Effects of Protein Size and Solvent Properties on Diffusion and Loading Efficiency.

Oral administration of protein-based therapeutics is highly desirable due to lower cost, enhanced patient compliance, and convenience. However, the harsh pH environment of the gastrointestinal tract poses significant challenges. Silica-based carriers have emerged as potential candidates for the delivery of protein molecules, owing to their tuneable surface area and pore volume. We explored the use of a commercial mesoporous silica carrier, SYLOID, for the delivery of octreotide and bovine serum albumin (BSA) using a solvent evaporation method in three different solvents. The loading of proteins into SYLOID was driven by diffusion, as described by the Stokes-Einstein equation. Various parameters were investigated, such as protein size, diffusion, and solubility. Additionally, 3D fluorescence confocal imaging was employed to identify fluorescence intensity and protein diffusion within the carrier. Our results indicated that the loading process was influenced by the molecular size of the protein as octreotide exhibited a higher recovery rate (71%) compared to BSA (32%). The methanol-based loading of octreotide showed uniform diffusion into the silica carrier, whereas water and ethanol loading resulted in the drug being concentrated on the surface, as shown by confocal imaging, and further confirmed by scanning electron microscopy (SEM). Pore volume assessment supported these findings, showing that octreotide loaded with methanol had a low pore volume (1.2cc/g). On the other hand, BSA loading was affected by its solubility in the three solvents, its tendency to aggregate, and its low solubility in ethanol and methanol, which resulted in dispersed particle sizes of 223 and 231μm, respectively. This reduced diffusion into the carrier, as confirmed by fluorescence intensity and diffusivity values. This study underscores the importance of protein size, solvent properties, and diffusion characteristics when using porous carriers for protein delivery. Understanding these factors allows for the development of more effective oral protein-based therapeutics by enhancing loading efficiency. This, in turn, will lead to advances in targeted drug delivery and improved patient outcomes.

Preparation, Swelling, and Drug Release Studies of Chitosan-based Hydrogels for Controlled Delivery of Buspirone Hydrochloride.

Buspirone is used for the management of depression and anxiety disorders. Due to its short half-life and low bioavailability, it requires multiple daily doses and is associated with some side effects. This study aimed to develop chitosan-based hydrogels as drug-controlled release carriers. The objective of this study is to prepare chitosan-based hydrogels as controlled release carriers in order to overcome the side effects of buspirone HCl and improve patients' compliance and their life quality. Polymer chitosan was polymerized with two monomers, acrylic acid and itaconic acid, to synthesize pH-sensitive hydrogel. The Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis were performed to confirm the structure formation and thermal stability. Water penetration capability and loading of the drug were performed by porosity and drug loading studies. The swelling and dissolution tests were performed to analyze the pH-sensitive nature of the developed hydrogels. FTIR, TGA, and DSC demonstrated that the chitosan-based hydrogels were successfully prepared. An increase in water penetration and drug loading into the hydrogel network was seen with the high incorporation of chitosan, acrylic acid, and itaconic acid. The swelling and dissolution studies revealed that prepared hydrogel offered the greatest swelling and drug release at a high pH of 7.4. The swelling and drug release from the hydrogel were affected by the concentrations of the incorporated contents. A controlled release of the drug was achieved by using chitosan-based hydrogel as a delivery carrier compared to commercial tablets of buspirone. The results showed that the developed chitosan-based hydrogel can be considered one of the most suitable drug carrier systems for the controlled delivery of buspirone.

CFD-FEM simulation of hydroelastic responses and slamming loads of a bow-flare ship advancing in head regular waves

ABSTRACT In this paper, the global motions and wave loads on a large bow-flare ship with the effect of hydro-elasticity, including whipping and springing, are numerically simulated by a CFD-FEM two-way coupled method. The simulation results of ship motions and wave loads by employing the numerical method are demonstrated by verification and validation studies including comparison with tank model experiment results. Additionally, the presented method is applied to study the motions, wave loads and slamming loads of the ship in different wave conditions. The vertical bending moment and vertical shearing force of different frequency components and their distribution along ship length are studied. The characteristics of slamming pressure and green water loads and their spatial distribution are studied. The simulation results indicate that the present numerical method well reproduces ship seakeeping and hydro-elasticity and has potential application values in the design and evaluation of ship wave loads.

Effects of Water Mist on the Initial Evolution of Turbulent Premixed Hydrogen/Air Flame Kernels

In this study, a series of carrier-phase direct numerical simulations are conducted on spherical expanding premixed hydrogen/air flames with liquid water addition. An Eulerian–Lagrangian approach with two-way coupling is employed to describe the liquid–gas interaction. The impacts of preferential diffusion, the equivalence ratio, water loading, and the initial diameter of the water droplets are examined and analyzed in terms of flame evolution. It is observed that liquid water has the potential to influence flame propagation characteristics by reducing the total burning rate, flame area, and burning rate per unit area, attributed to flame cooling effects. However, these effects become discernible only under conditions where water evaporation is sufficiently intense. For the conditions investigated, the influence of preferential diffusion on flame evolution is found to be more significant than the interaction with liquid water. The results suggest that due to the slow evaporation rate of water, which is a result of its high latent heat of evaporation, the water droplets do not disturb the initial flame kernel growth significantly. This has implications for water injection concepts in internal combustion engines and for explosion mitigation.

Study on energy consumption and failure mechanism of water-saturated coal sample during impact cracking

To uncover the mechanism of energy dissipation in coal samples when subjected to both water and dynamic load, the damage patterns and energy absorption properties of coal samples in their natural and saturated states were investigated and analyzed through Hopkinson impact experiments. The results of the study show that the mass and wave velocity of the natural coal samples show an increasing trend when they are saturated with water. And the mass and wave velocity increase by 6.35 % and 21.42 % respectively. The coal sample's level of fragmentation and dynamic strength exhibited a positive correlation with the velocity (1 m/s-5.69 m/s) of impact. When subjected to dynamic loads, both natural and water-saturated coal samples primarily undergo splitting, fracturing, and crushing. Compared with natural coal samples, saturated water coal samples show greater degree of crushing and lower mechanical strength. The dynamic strength of saturated coal sample at 5.25 m/s (15.66 MPa) decreased by 33.86 % compared with that at 5.69 m/s (23.68 MPa). The mean size of particles in coal samples, both in their natural state and when saturated with water, had an linear reduction relationship with impact speed. Conversely, the fractal dimension, which represents dissipation, had a direct relationship with impact speed. The fractal dimensions of dry and saturated coal samples are distributed in the ranges of 1.56–2.08 and 1.65–2.1, respectively. And the dissipative energy of natural coal samples between 1.09 m/s and 5.67 m/s is about 0.039 J/cm3-0.175 J/cm3, and that of saturated coal samples between 1 m/s and 5.25 m/s is about 0.034 J/cm3-0.088 J/cm3. The surface energy of coal samples was analysed and calculated, and an energy consumption prediction model was proposed to predict the energy consumption of coal samples after dynamic crushing.

Tempo-spatial Variations in Nitrogen and Phosphorus Loads in Jianli-Hankou Reach of the Middle Yangtze River During the Past 20 Years

Ammonia nitrogen （NH4+-N） and total phosphorus （TP） were the major control pollutants in the Yangtze River Basin. Based on measured data from 2003 to 2020, the temporal and spatial variations in concentrations and fluxes of NH4+-N and TP in the Jianli to Hankou （JL-HK） reach of the Middle Yangtze River were studied, and the impacts of flow-sediment factors, tributary inflows, and others on variations in NH4+-N and TP fluxes were discussed. The results showed that： ① In recent years, NH4+-N and TP concentrations in the mainstream have declined significantly, with annual NH4+-N and TP concentrations at each monitoring station in 2020 averagely decreasing by 41% and 34% compared to those in 2003, respectively. Spatially, NH4+-N and TP concentrations decreased and then increased along the mainstream. NH4+-N and TP concentrations of tributary inflows, which include the Dongting Lake and Han River, were generally lower than that of the mainstream. The multi-year average values of NH4+-N and TP concentrations were both averaged at 0.12 mg·L-1 in the mainstream and were averaged at 0.11 mg·L-1 and 0.09 mg·L-1 in the tributary inflows. ② The flux differences between the upper and lower sections net of tributary confluences showed that NH4+-N and TP fluxes were lost in the Jianli to Luoshan （JL-LS） sub-reach and increased in the Luoshan to Hankou （LS-HK） sub-reach in most years. NH4+-N and TP fluxes decreased in the JL-LS sub-reach, which was related to the lower NH4+-N and TP concentrations in lateral inflows, such as Dongting Lake, and thus lowered the NH4+-N and TP concentrations in the mainstream. The LS-HK sub-reach showed the opposite trends, and the water and sediment loads increased in this sub-reach. Across the whole JL-HK reach, TP flux as well as water and sediment loads were recharged along the reach, whereas NH4+-N flux was reduced greatly, which could be attributed to the pollution abatement conducted in the Yangtze River Basin, which mainly focused on NH4+-N. ③ The correlation analysis results showed that NH4+-N fluxes had the strongest correlation with NH4+-N concentrations but not significantly correlated with discharges and sediment transport rates, indicating that NH4+-N was mainly controlled by point source pollution in the study reach. TP fluxes had higher correlations with discharges and sediment transport rates in high flow level periods, and the correlations between TP fluxes and TP concentrations were better in low flow level periods, reflecting that point source pollution contributed more to TP in dry seasons compared to flood seasons.

An attention-neural-processes approach to reconstructing unsteady water load for seaplanes

The distribution of holographic unsteady water load offers important information for evaluating the hydrodynamic performance of seaplanes. However, traditional tank test is limited by the number of sensors that can be deployed on the bottom of hull, thus only providing sparse data for estimating load distribution and leading to inaccurate evaluation of seaplane performance. To achieve accurate and rapid reconstruction of holographic load distribution, a machine learning load-reconstruction model based on Attention Neural Processes is proposed. This model performs spatiotemporal modeling of seaplane water load utilizing sparse sensor data. It directly learns the load patterns across multiple time steps and employs Attention modules to capture the spatial distribution of load. Comparisons with alternative methods demonstrate the model's superior ability to simultaneously capture spatial and temporal dependencies of the unsteady load data. In addition, the model's robust generalization capability is also validated by reducing the number of sensors in the training data. The results indicate that the proposed model exhibits high prediction efficiency, accuracy, and generalization for the reconstruction of unsteady water load distribution, which is of great significance for comprehensively evaluating the hydrodynamic performance of seaplanes.

Evaluation of the mechanical properties of stiffened composite panels under consideration of water load

Abstract To meet the strength evaluation requirements of a typical stiffened composite panel of the lower fuselage of a new generation amphibious aircraft underwater load, the experimental testing technique and finite element analysis method were investigated. Firstly, according to the loading and support requirements of the typical stiffened composite lower fuselage panel, a testing device for combined axial and pneumatic loading was designed and developed. Then, a finite element model of the stiffened composite plate and the combined load testing device were created. Based on the experiments and finite element analysis, the static strength of the stiffened composite plate was verified to meet the load-bearing capacity requirements, and the strain behavior during loading was determined. Compared with the experimental results, the maximum strain error at the skin is 6.16%, and the maximum strain error at the stiffener is -11.6%. This confirms the effectiveness of the finite element model and also confirms that the test technique and equipment can accurately simulate in-plane axial loading and out-of-plane water loading. Finally, based on the validated finite element model, the load-bearing capacity of the stiffened composite panel under combined loads was predicted.

Inducible deletion of the prostaglandin EP3 receptor in kidney tubules of male and female mice has no major effect on water homeostasis.

The prostaglandin E2 (PGE2) receptor EP3 has been detected in the thick ascending limb (TAL) and the collecting duct of the kidney, where its actions are proposed to inhibit water reabsorption. However, EP3 is also expressed in other cell types, including vascular endothelial cells. The aim here was to determine the contribution of EP3 in renal water handling in male and female adult mice by phenotyping a novel mouse model with doxycycline-dependent deletion of EP3 throughout the kidney tubule (EP3-/- mice). RNAscope demonstrated that EP3 was highly expressed in the cortical and medullary TAL of adult mice. Compared with controls EP3 mRNA expression was reduced by >80% in whole kidney (RT-qPCR) and nondetectable (RNAscope) in renal tubules of EP3-/- mice. Under basal conditions, there were no significant differences in control and EP3-/- mice of both sexes in food and water intake, body weight, urinary output, or clinical biochemistries. No differences were detectable between genotypes in handling of an acute water load or in their response to the vasopressin analog 1-deamino-8-d-arginine-vasopressin (dDAVP). No differences in water handling were observed when PGE2 production was enhanced using 1% NaCl load. Expression of proteins involved in kidney water handling was not different between genotypes. This study demonstrates that renal tubular EP3 is not essential for body fluid homeostasis in males or females, even when PGE2 levels are high. The mouse model is a novel tool for examining the role of EP3 in kidney function independently of potential developmental abnormalities or systemic effects.NEW & NOTEWORTHY The prostanoid EP3 receptor is proposed to play a key role in the kidney tubule and antagonize the effects of vasopressin on aquaporin-mediated water reabsorption. Here, we phenotyped a kidney tubule-specific inducible knockout mouse model of the EP3 receptor. Our major finding is that, even under physiological stress, tubular EP3 plays no detectable role in renal water or solute handling. This suggests that other EP receptors must be important for renal salt and water handling.

Multi-Objective optimal scheduling of energy Hubs, integrating different solar generation technologies considering uncertainty

For a few decades, operators of energy systems have sought to achieve appropriate frameworks due to energy crises and rapid growth in energy requirements. In this regard, this study presents a multi-objective optimization model for an energy hub (EH) designed to manage a diverse energy portfolio. The EH receives electricity, natural gas, hydrogen, seawater, and solar energy as inputs, aiming to satisfy electricity, heating, and freshwater demands at the output port while considering a limited available area. The model incorporates the selection of the optimal solar energy technology (photovoltaics, parabolic dish, or parabolic trough collector) through a comprehensive evaluation encompassing technical, economic, and environmental aspects. To achieve optimal scheduling of the EH’s production units, the model factors in forecasts of solar energy availability alongside electrical, heat, and water load demands. The evaluation of the EH’s performance is conducted through a multi-objective framework considering social welfare, CO2 emissions, voltage stability margin (VSM), a newly proposed simplified fast temperature stability index (SFTSI), and a similarly novel simplified fast pressure stability index (SFPSI). The optimization problem is formulated within a MATLAB environment and solved using a multi-objective Archimedes optimization algorithm across five distinct case studies, each characterized by a varying designated area for solar energy generation. The effectiveness of the proposed model and optimization technique is validated through test systems, with the obtained results demonstrating significant improvements compared to a baseline scenario. These improvements include a 36.18% reduction in CO2 emissions, a 14.22% increase in total social welfare, and reductions in the average values of VSM, SFTSI, and SFPSI when incorporating all solar energy technologies.

3D Printed Concrete: Fresh and Hardened Properties

3D concrete printing (3D CP) is an advanced form of additive manufacturing (AM), that allows for the creation of complex geometrical structures using concrete. This technology has the potential to reduce construction time and labour costs while minimizing material waste. However, there are also challenges related to material properties, structural integrity, and standardization of construction practices. The primary challenge in developing 3D printable cementitious materials lies in engineering specific fresh properties that enable extrusion-based printing. Unlike cast concrete, where formwork provides dimensional stability during the printing process, the absence of formwork in 3D printing necessitates fresh mixtures with low-slump and high-thixotropy to be suitable for concrete 3D printing. Additionally, the orthotropic nature of the resulting 3D printed object due to the extrusion process impacts its mechanical properties. Therefore, this research aims to study the effect of water content and loading directions on 3D printed concrete. A pre-mix material from Sika was used in this study. Three mixes were prepared by using three different water to dry material (w/d) ratios, 0.140 l/kg, 0.145 l/kg and 0.150 l/kg. The experiments focused on analysing flowability, green strength, mechanical properties (compressive strength, flexural strength, and modulus of elasticity), water absorption, porosity, and chemical transformations at high temperatures through thermoanalytical measurement. The results showed that the mixture containing 0.145 l/kg (w/d) exhibited satisfactory 3D printability, optimal mechanical performance, lower porosities compared with mixtures 0.140 and 0.150, and same total porosity compared with cast specimen.

Perancangan Rangka Tandon Air Berkapasitas 1200 Liter Untuk Kebutuhan Pelaku Usaha Rumah Kost

The increasing public interest in the need for adequate housing, especially the boarding house business, is one of the facilities that has great opportunities every year. The need for clean water in a boarding house environment is a factor that needs to be considered because clean water is an important need in human life. The water reservoir frame design with a capacity of 1200 liters is an optimized solution to meet the daily water needs of boarding house residents. The aim of this research is to design a water reservoir frame for water loads and carry out structural calculations of the water reservoir frame in accordance with applicable safety and strength standards. The research methodology explains in detail the research method which includes time and place of research, tools and materials, research procedures and research flow diagrams. Weight of load to be supported by the structure = weight of tank + weight of water Specify tank Type = Penguin TB, 120 uk Capacity = 1200 Liters = 1.2 m3 Tank mass (mT) = 29 kg Total mass of external load (mtot) = tank mass + water mass Mtot= 29 kg + 1200 kg = 1229 kg Total weight (Wtot) Wtot = (mtot) × g, g= acceleration due to gravity (9.8 m/s2) Kata kunci: Water discharge, Frame Strength, Structural Strength, Steel Selection, Water Reservoir