Channel Walls Research Articles

Anomalous Heat Transfer Enhancement in Separated Flow over a Zigzag-Shaped Dense Package of Inclined Grooves in a Channel Wall at Different Temperature Boundary Conditions

Anomalous Heat Transfer Enhancement in Separated Flow over a Zigzag-Shaped Dense Package of Inclined Grooves in a Channel Wall at Different Temperature Boundary Conditions

Drag reduction in a minimal channel flow with scientific multi-agent reinforcement learning

We study drag reduction in a minimal turbulent channel flow using scientific multi-agent reinforcement learning (SMARL). The flow is controlled by blowing and suction at the wall of an open channel, with observable states derived from flow velocities sensed at adjustable heights. We explore the actions, state, and reward space of SMARL using the off-policy algorithm V-RACER. We compare single- and multi-agent setups, and compare the identified control policies against the well-known mechanism of opposition-control. Our findings demonstrate that off-policy SMARL reduces drag in various experimental setups, surpassing classical opposition-control by up to 20 percentage points.

A study of continuous double diffusive convection of binary liquid in an alloy form by employing Lapwood-Brinkman model with cross diffusion effect.

In this paper we study the effect of DuFour and Soret on linear double diffusive convection of binary liquid in a two dimensional rectangular channel filled with anisotropy porous material using Lapwood-brinkman model with cross diffusion effect. Darcy model without a time derivative is used in the momentum equation. Linear stability assessment is used to investigate the walls of channels that are heated and salted from below due to Soret and DuFour effects. The anisotropic parameters, the solute Rayleigh number, and the impacts of Soret and DuFour on the onset of convection are examined and same is plotted graphically.

Numerical Study of Convection Heat Transfer with Confinement Around a Square Cylinder Submerged in a Water-Based Nanofluid

The novelty of this work lies in the comprehensive investigation of Forced convection heat transfer a square cylinder inclined at 45° using CuO nanofluid employing a single phase approach. A heated square cylinder with constant wall temperature boundary condition, subjected to a flowing nanofluid between two parallel walls, undergoes a laminar, steady and two-dimensional flow within a Reynolds number range of 1 < Re > 40. To obtain solutions for the flow and energy transfer, a Finite Element Method (FEM) is employed to numerically solve the governing differential equations and boundary conditions. The objective of this work is to highlight the effects of Reynolds number (Re), confinement ratio (λ), volume concentration (Φ) and diameter of nanoparticles (dnp) on fluid flow and heat transfer characteristics of nanofluid. To capture the effect of Φ and dnp in nanofluid, the thermo-physical-properties of CuO nanofluid are determined experimentally. In the results, at Re = 40, a secondary separation zone (recirculation zone) is observed near the surface of the channel wall. The drag coefficient value rises as the Φ increases and the vdnp decreases, regardless of other factors such as Re and λ. Conversely, as the confinement ratio and volume fraction of nanoparticles increase, the average Nusselt number also rises, while maintaining a constant value of Re and dnp. In contrast, the size of the nanoparticles exhibits an inverse relationship with the average Nusselt number. The study contributes to the understanding of nanofluid behavior and provides practical insights for applications, supported by correlations and Artificial Neural Network predictions (Parrales et al.).

Anchoring thiol-rich traps in 1D channel wall of metal-organic framework for efficient removal of mercury ions

Anchoring thiol-rich traps in 1D channel wall of metal-organic framework for efficient removal of mercury ions

Characteristics of planar buoyant jets and plumes in a turbulent channel crossflow from direct numerical simulations

AbstractThis paper is motivated by an interest in understanding the characteristics of buoyant fluids discharged from the bottom wall of channels, such as encountered during tunnel fires or in river effluent discharge. Direct numerical simulation is used to model the upward release of a planar buoyant jet or plume from the bottom wall of a channel into an incoming turbulent crossflow. The well-studied jet-in-crossflow with only a momentum source is simulated first, and subsequently, fixing the incoming Reynolds number, buoyancy source as heat flux is added alongside varying momentum source, with two cases where only a buoyancy source is present. Appropriate five non-dimensional parameters relevant for this flow are defined, of which three are fixed and two—source to channel momentum ratio and Richardson number—are varied. The changes in turbulence characteristics as the buoyant jet or plume evolves downstream are presented. In all cases with buoyancy, except for the pure jet case, the plume is initially confined to the lower half of the channel before it suddenly lifts to the top half, an effect that occurs at an increasingly smaller downstream distance with increasing buoyancy, and dividing the flow into a near and far field. The distributions of mean and Reynolds stresses in the near and far field of the source are reported, and it is found that the channel flow becomes more turbulent downstream of the source, and further, the turbulent vertical temperature flux switches sign from near to far field owing the a change in the mean temperature gradient sign. From the input parameters and using the integrated temperature equation a reasonable estimate of the far field mean channel temperature can be obtained by a reference temperature based on the heat conservation that includes the convective and diffusive source heat flux. A monotonic behaviour of the back-layering distance is also observed a function of this reference temperature, which was difficult to obtain with the two specified non-dimensional parameters.

Droplet motion in a microchannel: The influence of electrokinetic effects at liquid-liquid interfaces

The electrokinetic effects at fluid interfaces can be utilized for droplet manipulation and separation in water, showing promising applications in areas such as oil-water separation and liquid-liquid extraction. In this study, numerical simulations are employed to investigate the impact of electrokinetic effects at the droplet surface and the horizontal interface between a non-conductive liquid and water on the electrokinetic velocity of a droplet within a microchannel. The findings indicate that as the magnitude of the negative zeta potential intensifies at the horizontal liquid-liquid interface, the flow velocity of non-conductive liquid gradually decreases and reverses direction when the zeta potential of the interface exceeds that of the channel wall. Conversely, the flow velocity of water continues to rise, resulting in an increased droplet movement velocity in water. The study also reveals that a lower water height and a greater non-conductive liquid height lead to faster water flow velocity and, consequently, a swifter droplet movement velocity. Additionally, the dynamic viscosity of the droplet has minimal impact on its electrokinetic velocity.

IMPACT OF SOLID BOUNDARIES AND VISCOSITY OF THE MEDIUM ON THE CONTRIBUTION OF THE INERTIAL AND VORTEX COMPONENTS OF THE NORMAL FORCE OF A ROTATING PLATE. PART 2

Within the framework of the improved method of discrete vortices, generalized for viscous media, a method has been developed for determining the contribution of forces of inertial, vortex and circulation nature to the normal force of a plate moving in a stationary viscous boundless medium accord- ing to an arbitrary law, in the presence of a wall and in a channel. The developed method was tested for the case of instantaneous angular start of the plate and subsequent constant angular speed of rotation (Wagner's problem) in a viscous boundless medium, in the presence of a wall and in a channel, in laminar and turbulent modes. The application of approximate analytical formulas for the components of the induced velocity from a discrete vortex in a viscous medium near the wall and in the channel made it possible to obtain velocity fields that visualize two vortices separated from the edges of the plate and the dynamics of their dispersion in laminar and turbulent regimes of rotation of the plate near the wall and in the channel. The inertial- vortical nature of the normal force of the plate (with the dominance of inertial forces) is confirmed, which rotates after an instantaneous start with the separation of the flow from both its edges, regardless of the presence of solid boundaries and laminar or turbulent flow regimes. It was found that in the case of the laminar regime, the effect of the presence of the wall on the reduced inertial component of the normal force of the plate is insignificant, but the influence of the channel leads to a faster departure of the laminar vortex from the moving edge of the plate, which leads to a gradual increase in the contribution of the inertial component of the normal force of the plate up to 100 % and more when turning the plate perpendicular to the channel walls. Approximately the same happens in the case of the absence of solid boundaries, when a turbulent vortex of a larger size and intensity than the corresponding laminar one moves away from the moving edge of the plate.

An Enhanced Temperature Control Approach to Simulate Profile Extrusion.

Thermoplastic extrusion, a widely used method for processing thermoplastic materials, requires precise temperature control to ensure product quality. However, existing computer-aided engineering tools often oversimplify the temperature distribution calculations, leading to additional discrepancies between simulations and the actual processes. This study introduces a novel multi-region modeling approach to address this issue. By employing realistic temperature control conditions, the methodology overcomes the limitations of current numerical modeling tools. The key contributions include the development of a transient, incompressible, non-isothermal solver integrated into the OpenFOAM computational library and the implementation of a specialized boundary condition that emulates Proportional-Integral-Derivative (PID) control using real-time thermocouple measurements. The findings highlight temperature deviations at the flow channel walls and total pressure drop while demonstrating a smaller impact on velocity and flow uniformity at the outlet under steady-state conditions. This research substantially advances the understanding of thermal dynamics in extrusion processes, offering crucial insights for enhancing temperature control and laying the groundwork for more effective and precise operational strategies.

Modelling Turbulent Flow of Superfluid 4\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{4}$$\\end{document}He Past a Rough Solid Wall in the T=\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$T =$$\\end{document} 0 Limit

We present a numerical study, using the vortex filament model, of vortex tangles in a flow of pure superfluid 4\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^4$$\\end{document}He in the T=0\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$T = 0$$\\end{document} limit through a channel of width D=1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$D = 1$$\\end{document} mm for various applied velocities V. The flat channel walls are assumed to be microscopically rough such that vortices terminating at the walls are permanently pinned; vortices are liberated from their pinned ends exclusively through self-reconnection with their images. Sustained tangles were observed, for a period of 80 s, above the critical velocity Vc∼0.20\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$V_c \\sim 0.20$$\\end{document} cm s-1=20κD\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{-1} = 20 \\frac{\\kappa }{D}$$\\end{document}. The coarse-grained velocity profile was akin to a classical parabolic profile of the laminar Poiseuille flow, albeit with a nonzero slip velocity ∼\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\sim$$\\end{document} 0.20 cm s-1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{-1}$$\\end{document} at the walls. The friction force was found to be proportional to the applied velocity. The effective kinematic viscosity was ν′∼0.1κ\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\ u ' \\sim 0.1\\kappa$$\\end{document}, and effective Reynolds numbers within Re′<200\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\mathrm {Re'} < 200$$\\end{document}. The fraction of the polarised vortex length varied between zero in the middle of the channel and ∼\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\sim$$\\end{document} 60% within the shear flow regions ∼D/4\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\sim D/4$$\\end{document} from the walls. Therefore, we studied a state of statically polarised ultraquantum (Vinen) turbulence fuelled at short length scales by vortex reconnections, including those with vortex images due to the relative motion between the vortex tangle and the pinning rough surface.

Impact of entropy generation and temperature gradient heat source on Couette flow in a permeable magnetic field

AbstractThis research paper focused on investigating the influence of various factors on steady Couette flow beneath a permeable bed. Factors studied included aligned magnetic field, thermal radiation, temperature gradient heat source, viscous dissipation, and Joules dissipation. The momentum and energy equations governing flow and heat transmission were analytically solved to predict the generation of entropy. The findings were visually presented through graphical representations, which effectively demonstrated the effect of these factors on the fluid's velocity, temperature, entropy production, and Bejan number. In addition, the shear stress and rate of heat transfer coefficient at the channel walls were computed and their behavior was documented in tables to provide further insights.

Enhancing the Cooling Efficiency of Aluminum-Filled Epoxy Resin Rapid Tool by Changing Inner Surface Roughness of Cooling Channels.

In low-pressure wax injection molding, cooling time refers to the period during which the molten plastic inside the mold solidifies and cools down to a temperature where it can be safely ejected without deformation. However, cooling efficiency for the mass production of injection-molded wax patterns is crucial. This work aims to investigate the impact of varying surface roughness on the inner walls of the cooling channel on the cooling efficiency of an aluminum-filled epoxy resin rapid tool. It was found that the cooling time for the injection-molded products can be determined by the surface roughness according to the proposed prediction equation. Employing fiber laser processing on high-speed steel rods allows for the creation of microstructures with different surface roughness levels. Results demonstrate a clear link between the surface roughness of cooling channel walls and cooling time for molded wax patterns. Employing an aluminum-filled epoxy resin rapid tool with a surface roughness of 4.9 µm for low-pressure wax injection molding can save time, with a cooling efficiency improvement of approximately 34%. Utilizing an aluminum-filled epoxy resin rapid tool with a surface roughness of 4.9 µm on the inner walls of the cooling channel can save the cooling time by up to approximately 60%. These findings underscore the significant role of cooling channel surface roughness in optimizing injection molding processes for enhanced efficiency.

MHD peristaltic two-phase Williamson fluid flow, heat and mass transfer through a ureteral tube with microliths: Electromagnetic therapy simulation

The ureter typically experiences a frequency of one to five peristaltic contractions per minute. However, it is important to note that these contractions can be disrupted by various physical and mechanical irritants. Ionic contents in the urine make it electrically conducting and responsive to electromagnetic body forces. MHD can be deployed in bio magnetic therapy to control or mitigate symptoms associated with peristaltic pumping in the urinary system. This article therefore focuses on the hydromagnetic effects on flow patterns of urine with debris (monoliths). The mechanism of urine flow is largely coordinated by the kidneys. The flow inside the ureter is interrupted by microliths, which are generated by the sedimentation of excretory products. To simulate this, a two-phase formulation is adopted, comprising the electromagnetic urological viscous fluid phase and the particulate phase for solid grains. The peristaltic propulsion of two-phase liquid in the ureter is simulated as a sinusoidal wave propagation of incompressible non-Newtonian fluid. The Williamson viscoelastic model is deployed for the rheology. Heat transfer is also included with Soret thermo-diffusion and viscous heating effects. Long wave and low Reynolds number approximations are employed based on lubrication theory. The mass, momentum, energy and concentration conservation equations with associated boundary conditions are rendered non-dimensional via appropriate scaling transformations. A numerical solution is achieved via BVP4C MATLAB quadrature. Graphical visualizations of the velocity, temperature and concentration (solid grains) are given for the influence of suspension parameter ( ζ ), Hartmann number (M), Prandtl number (Pr), Weissenburg number (We), particle volume fraction (C), Eckert number (Ec), Soret number (Sr), Schmidt number (Sc). The novelty of the present work is therefore the simultaneous consideration of a generalized two-phase model, wall slip, non-Newtonian characteristics, cross diffusion, viscous dissipation, mass diffusion, magnetic body force and curvature effects in peristaltic urological transport, which has not been undertaken previously. The detailed simulations reveal that the flow velocity is reduced due to the presence of solid particles and the channel curvature, in comparison to the flow in an unobstructed channel devoid of solid particles. Enhancing the hydrodynamic slip parameter speeds up the movement of particles and fluid near the channel walls, boosts wall skin friction, raises pressure difference in the pumping area, and amplifies bolus magnitudes.The rise in peristaltic pumping results in a reduction in solid particle concentration, which is significant phenomena.This theoretical approach may aid in treating conditions such as Urinary Tract Infections (UTIs). The computations effectively demonstrate that significant manipulation of urological pumping characteristics can be achieved with an electromagnetic field. Some new features of two-phase ureteral dynamics are highlighted as relevant to magnetic therapy techniques, which may be beneficial to clinicians.

Experimental conditions for efficient retention of vascular endothelial cells on channel wall using lipid bubbles and acoustic interference

In order to fabricate multi-layered artificial blood vessels, bubble-surrounded cells were retained on the wall in a flow channel using the phase sweeping of interferential acoustic field. First, spatial distribution of acoustic intensity was defined to evaluate retention performance. Comparing between various acoustic fields, we found appropriate acoustic intensity for retention of the cells. Next, phase sweeping of the acoustic field was conducted to increase the retained area of the cells by varying sweep velocity, sweep direction, and the amplitudes of sound pressure. As the result, an interferential acoustic field with a balanced sound pressures of 200 kPa-pp at a sweep velocity of 100 mm s−1, which was 10 times higher than the flow, and the sweep direction against the flow, obtained a retained area 1.6 times larger than that without sweeping. We will apply the conditions based on the results for the future 3D fabrication of artificial blood vessels.

Effects of Flow Pulsation and Surface Geometry On Heat Transfer Performance in a Channel with Teardrop-Shaped Dimples Measured by Transient Technique

Abstract This study focuses on the heat transfer performance of a pulsating flow over a channel surface with teardrop-shaped dimples. Heat transfer measurements were performed by a transient technique with compensation of three-dimensional heat conduction under a bulk Reynolds number of 25,000. Seven types of surfaces with the teardrop-shaped dimples were examined, where dimple arrangement (in-line/staggered) and inclination angle (0-60 deg) were varied. A pulsating flow with the Strouhal number of 0.15 was generated by vibrating a rubber film section on the channel wall using a vibration generator. The pulsation amplitude was evaluated by calculating the root-mean-square value of the phase averaged velocity. Two conditions of the pulsation amplitudes were examined (0.09 and 0.12 of mean velocity). The results showed that the surface-averaged Nusselt number and friction factor for the pulsating flow increased from those for the steady flow. The highest increases of the surface-averaged Nusselt number and heat transfer efficiency index appeared in the 30deg in-line arrangement, and those were 16.1% and 9.8%, respectively, at most as compared with the steady case. Due to the flow pulsation, the local Nusselt number was enhanced at the leading-edge region of the dimples, and supplementary RANS/URANS results showed that the flow separation size was shrunk by the flow pulsation there.

Numerical exploration of the peristaltic flow of MHD Jeffrey nanofluid through a non-uniform porous channel with Arrhenius activation energy

This article describes the peristaltic flow of a Jeffrey nanofluid through a vertical divergent channel subject to the impacts of thermal radiation, heat generation, activation energy, and an angled magnetic field. Coupled governing non-linear differential equations are obtained by approximating the system with the lubrication approximation. Further, distributions of the velocity, temperature, concentration, heat, and mass transfer rates at the channel wall are all calculated numerically. In addition, the consequences of pertinent physical parameters on the flow quantities are analyzed via tabular and graphical illustrations. It is noted that the velocity distribution exhibits an increasing behavior for thermal and solute Grashof numbers. Augmentation in axial velocity is noticed by escalating the values of the Hall current parameter. For greater values of the activation energy parameter, the concentration and mass transfer rate were elevated. The present study has a wide range of applications in biomedical engineering and environmental engineering.

P-702 Centrifugal Pump Damage Analysis Insights and Implications

Centrifugal pumps are widely used in industries for fluid transfer, operating on the rotation of an impeller driven by a prime mover. However, sudden performance drops and operational instability pose significant challenges, impacting overall system efficiency. Predictive maintenance relies on vibration analysis to assess rotating equipment condition, with vibration patterns indicating potential issues such as cavitation and corrosion. Prolonged cavitation leads to erosion of channel wall surfaces, resulting in structural damage. This study aims to address the knowledge gap in understanding the relationship between pump vibration, cavitation, and corrosion. Through comprehensive vibration analysis and examination of pump performance, our research identifies the mechanisms driving pump degradation. The findings highlight the critical role of predictive maintenance in mitigating pump failures and optimizing system performance. Highlights : Vibration analysis crucial for predictive maintenance: Identifying early signs of pump deterioration. Cavitation-induced erosion: Understanding the impact of prolonged cavitation on pump performance. Importance of proactive maintenance: Mitigating pump failures and optimizing system efficiency. Keywords : Centrifugal pumps, Vibration analysis, Cavitation, Corrosion, Predictive maintenance

Effects of Nanoparticle Wettability on the Meniscus Stability of Oil-Water Systems: A Coarse-Grained Modeling Approach.

A coarse-grained modeling approach is employed to probe the effect of nanoparticles and their wettability on the stability of the interface between two immiscible fluids. In this study, pure oil (dodecane) and water are placed side by side in a nanochannel, forming a meniscus. Homogeneous hydrophilic nanoparticles, Janus particles, and homogeneous hydrophobic nanoparticles are placed at the oil-water interface, and their dynamics are studied as they rearrange at the oil-water interface. The results show that when the water is set in motion, two instabilities occur: the formation of fingers and the detachment of water from the channel wall. It is observed that the formation of fingers is affected by the wettability of the nanoparticles. The second instability may lead to the formation of a drop that propagates through the channel. However, it is found that the wetting properties of the nanoparticles do not affect the critical flow rate for the detachment of the water from the wall. Therefore, detachment occurs at the same three-phase contact angle regardless of the nanoparticle wetting properties. These findings can be important for industrial applications such as enhanced oil recovery, separation technologies, and microfluidic and nanofluidic technologies.

Irreversibility estimation of MHD thermosolutal convection of Powell–Eyring fluid flow through an inclined microchannel

ABSTRACT Due to the impressive utility of the mass transport phenomena on microscales for various miniaturised devices, the theoretical and experimental studies in microchannel flows to analyse heat and mass transport find enormous interest in researchers. Investigations in microchannel flows have gigantic applications in biochips, drug delivery, and cooling of microchips. This article examines the combined heat and mass transport of Powell–Eyring fluid through a permeable inclined microchannel considering magnetism, thermo-diffusion, and Navier's slip effects under convective boundary conditions. To solve the nonlinear system numerically MATLAB bvp4c solver is employed. This analysis reveals that the entropy generation due to thermosolutal irreversibility is enhanced strictly with the thermo-diffusion effect and solutal Biot number. The Bejan number profile shows a dominating character of Reynold's number close to the upper channel wall and deteriorates with the immense solutal Grashoff number. Also, it achieves maximum and minimum values for the supreme thermal Biot number and Eckert number, respectively in the middle of the channel. The outcome of the study may provide significant insight into controlling flows through microchannels as well as manipulating microfluidic and biomedical devices for minimising energy loss and designing an efficient model for better thermal performance and transmission of chemical species.

A hydrodynamic-based dual-function microfluidic chip for high throughput discriminating tumor cells

A hydrodynamic-based microfluidic chip consisted of two function units that could not only separate tumor cells (TCs) from whole blood but also remove residual blood cells was designed. The separation of TCs was achieved by a straight contraction-expansion array (CEA) microchannel on the front end of the chip. The addition of contractive structure brought a micro-vortex like Dean vortex that promoted cell focusing in the channel, while when cells entered the dilated region, the wall-induced lift force generated by the channel wall gave cells a push away from the wall. As the wall-induced lift force is proportional to the third power of the cell diameter, TCs with larger diameter will have a larger lateral migration under the wall-induced lift force, realizing the separation of TCs from blood sample. Fluorescent particles with diameters of 19.3 μm and 4.5 μm were used to simulate TCs and red blood cells, respectively, to verify the separation capacity of the proposed CEA microchannel for particles with different diameter. And a separation efficiency 98.7% for 19.3 μm particles and a removal rate 96.2% for 4.5 μm particles was observed at sample flow rate of 10 μL min−1 and sheath flow rate of 190 μL min−1. In addition, a separation efficiency about 96.1% for MCF-7 cells (stained with DiI) and removal rates of 96.2% for red blood cells (RBCs) and 98.7% for white blood cells (WBCs) were also obtained under the same condition. However, on account of the large number of blood cells in the blood, there will be a large number of blood cells remained in the isolated TCs, so a purification unit based on hydrodynamic filtration (HDF) was added after the separation microchannel. The purification channel is a size-dictated cell filter that can remove residual blood cells but retain TCs, thus achieving the purification of TCs. Combined the CEA microchannel and the purifier, the microchip facilitates sorting of MCF-7 cells from whole blood with a separation rate about 95.3% and a removal rate over 99.99% for blood cells at a sample flow rate of 10 μL min−1, sheath flow rate of 190 μL min−1 and washing flow rate of 63 μL min−1.