Wall Protection Research Articles

Experimental Study of Used Wind Turbine Blades for Their Reuse in Slope and Trench Protection.

This article presents the results of an experimental study carried out to assess the possibility of using waste wind turbine blades as retaining wall structures for slopes and trenches. The use of Vestas and LM-type blades as retaining wall components was assumed, based on 'columns' made of Vestas-type closed profiles filled with concrete and 'slabs' of fragments extracted from LM-type blades. The results of the tests and comparisons of the displacement and strain values of the components obtained using different measurement methods are presented in this paper. The force-strain and force-displacement relationships obtained from the tests were used to validate numerical models of slope protection walls and excavations designed from used wind turbine blades. According to our research, there is a high degree of variability in the strength parameters and deformation of the composite elements made from the wind turbine blades. Therefore, in the case of this type of material, characterized by a significant variation in carrying capacity, deformability, and the nature of the failures, the use of different measurement methods makes it possible to obtain much of the data necessary for assessing the reusability of wind turbine blades in building.

Mapping Sliding Ferroelectricity in Bulk (PbS)1.11VS2 Crystals

The recent discovery of sliding ferroelectricity opens up the field of 2D ferroelectricity. However, the limitation to switching the polarization due to the topological protection of the domain walls limits the potential of these heterostructures. Here, the switching of sliding ferroelectric bulk misfit layer compound (PbS)1.11VS2 crystals is studied using switching spectroscopy piezoresponse force microscopy. A large number of measured hysteresis loops can be efficiently analyzed using unsupervised machine‐learning tools. Different switching behavior of the domains is observed on different types of domain structures, and it is shown that full domain switching can be observed for the right type of dislocation structure in the PbS layer.

A cell membrane-targeted photosensitizer for cancer photodynamic therapy and dynamic ablation process tracking

Photodynamic therapy (PDT) uses photosensitizer (PS) to generate reactive oxygen species (ROS) under light to trigger cell apoptosis in cancer treatment. Organelle-targeted PS can effectively enhance the efficacy of phototherapy by specifically destroying subcellular organelles. The cell membrane, as an important organelle, is the “protective wall” of cells maintaining the integrity and normal life activities of cells. The damage to cell membranes is fatal to cells. However, utilizing functional PS to achieve cell membrane-targeted PDT, and realize real-time and accurate in situ reporting of cell membrane damage and monitoring of the treatment process, are challenging tasks. In this work, we prepared a photosensitizer (2TPAO) with aggregation-induced emission (AIE) characteristics, good water solubility, strong near-infrared fluorescence, and the capability for specific imaging of cell membranes. Moreover, 2TPAO could effectively produce ROS under visible light irradiation and achieve photodynamic ablation of tumor cells and tumors. Meanwhile, during PDT, the fluorescence changes of 2TPAO indicated the destruction of cell membranes, allowing intuitive determination of the phototherapy results. Therefore, 2TPAO is an effective cell membrane-targeted PS for cancer PDT.

Support Vector Machine Framework for Detecting Ambiguous Contours of Space Debris Cloud

Operational spacecraft are prepared for collisions with space debris by installing protective walls (bumpers). A group of vaporized and liquefied microparticles generated by debris collisions is called a debris cloud. To evaluate the protective performance of bumpers, it is important to measure the spread velocity and angle of the debris cloud. However, debris cloud images exhibit ambiguous contours of debris clouds. Consequently, measurement errors in the spread velocity and spread angles occur because of the observer’s subjectivity. Commonly used derivative-based methods can detect steep contours; however, they cannot detect ambiguous contours such as those of debris clouds. In this study, a method for uniquely detecting the ambiguous contours of a debris cloud based on supervised machine learning and a continuous wavelet transform (CWT) is proposed. Feature points that indicate candidate points of the debris cloud contour are extracted using a method based on CWT. Four types of specific features for debris cloud contours were assigned to the feature points. Supervised machine learning using a support vector machine can detect the debris cloud contours. The proposed method enables the evaluation of the ambiguous contours of a debris cloud and the protection performance of a bumper without observer subjectivity.

Illegal luxuritecture: How the super-rich in Hong Kong land grab and unlawfully expand their luxury living spaces

This article introduces the concept of ‘illegal luxuritecture’ – illegal luxury architecture – to capture the way a minority of super-rich expand their living environments without planning permissions, sometimes through land grabs of government land. Typically, illegal housing is associated with the urban poor, but it is argued that through elite capture, unauthorised building works (UBWs) have also been utilised by the super-rich. This article focusses on Hong Kong where a number of illegal luxuritectural structures came to light after September 2023 when the most severe rainstorm since records began in the 19th century caused the collapse of unauthorised building works. Illegal luxuritectural construction involves illegally altering building foundations and sometimes flood protection walls, causing destabilisation of soil and creating landslides. Although failure to comply with Building (Planning) Regulations and the Buildings Ordinance is a criminal offence which can result in fines or imprisonment, findings suggest that a minority of the elite class tends to ignore these regulations. This is because, the fines for unauthorised building works are relatively small in relation to the high value of the property or the rental income generated, and prison sentences are almost never imposed. This article contributes to the current academic discussions on the super-rich in general and the housing of the global super-rich in particular.

Coupling study of onboard power generation system of Magnetohydrodynamics enhanced Brayton Cycle

Closed cycle power generation systems offer a possible solution to meet the high electricity needs of hypersonic vehicles, but the power generation is limited by the finite cold source and cycle temperature. Introducing two-phase flow liquid metal (LM) MHD power generation based on Closed-Brayton-Cycle (CBC) is a potential solution that can enhance the thermal-electricity conversion process at the system level. However, it is difficult to reflect the complex coupling relationship between the power generation system and the vehicles propulsion system and the limitations of finite cold sources by relying only on ideal system analysis, especially the contradiction between the void fraction and the mass flow of working fluid after the introduction of LMMHD power generation. The study utilizes a multi-dimensional model to evaluate the performance of the CBC enhanced by multi-stage LMMHD generators coupled with hydrocarbon fuel scramjet. The multi-stage mixing-separation LMMHD generator is proposed to decouple the void fraction of the MHD channel and the wall cooling process, and control the void fraction by change number of stages. The calculation result indicate that the void fraction significantly affects the overall power generation performance, including output power, performance boundary, etc. Increasing the void fraction is beneficial, and the optimal void fraction is 0.65. At the same Mach number, the fuel cooling capacity available to the system increases with the fuel equivalence ratio, resulting in higher total power output. The maximum Mach number for thermal protection of the combustor walls alone may surpass 9.5. For gas void fractions of 0.35/0.5/0.65, the maximum power generation reaches 182.8/167.1/156.9 kW, respectively. The novel system is compared with other advanced thermal-electricity conversion cycles under nearly the same conditions and demonstrated clear performance advantages.

LiDAR-Based Urban Three-Dimensional Rail Area Extraction for Improved Train Collision Warnings.

The intrusion of objects into track areas is a significant issue affecting the safety of urban rail transit systems. In recent years, obstacle detection technology based on LiDAR has been developed to identify potential issues, in which accurately extracting the track area is critical for segmentation and collision avoidance. However, because of the sparsity limitations inherent in LiDAR data, existing methods can only segment track regions over short distances, which are often insufficient given the speed and braking distance of urban rail trains. As such, a new approach is developed in this study to indirectly extract track areas by detecting references parallel to the rails (e.g., tunnel walls, protective walls, and sound barriers). Reference point selection and curve fitting are then applied to generate a reference curve on either side of the track. A centerline is then extrapolated from the two curves and expanded to produce a 2D track area with the given size specifications. Finally, the 3D track area is acquired by detecting the ground and removing points that are either too high or too low. The proposed technique was evaluated using a variety of scenes, including tunnels, elevated sections, and level urban rail transit lines. The results showed this method could successfully extract track regions from LiDAR data over significantly longer distances than conventional algorithms.

Mechanical strategies supporting growth and size diversity in Filamentous Fungi.

The stereotypical tip growth of filamentous fungi supports their lifestyles and functions. It relies on the polarized remodeling and expansion of a protective elastic cell wall (CW) driven by large cytoplasmic turgor pressure. Remarkably, hyphal filament diameters and cell elongation rates can vary extensively among different fungi. To date, however, how fungal cell mechanics may be adapted to support these morphological diversities while ensuring surface integrity remains unknown. Here, we combined super-resolution imaging and deflation assays to measure local CW thickness, elasticity and turgor in a set of fungal species spread on the evolutionary tree that spans a large range in cell size and growth speeds. While CW elasticity exhibited dispersed values, presumably reflecting differences in CW composition, both thickness and turgor scaled in dose-dependence with cell diameter and growth speeds. Notably, larger cells exhibited thinner lateral CWs, and faster cells thinner apical CWs. Counterintuitively, turgor pressure was also inversely scaled with cell diameter and tip growth speed, challenging the idea that turgor is the primary factor dictating tip elongation rates. We propose that fast-growing cells with rapid CW turnover have evolved strategies based on a less turgid cytoplasm and thin walls to safeguard surface integrity and survival.

Methodology for shielding design and evaluation for container scanners.

There has been an increase in the use of high energy photon beam for container scanners in many countries for multi purposes such as detecting high atomic number materials which might be nuclear materials, drugs, high explosive materials and other contrabands etc. High energy photon beams generally 6 and 9 MV can be used for scanning such materials. However, it is important to ensure that radiation level beyond the container scanner installation is within the permissible dose limit specified by the national competent authority for the protection of public and radiation workers. In this paper, challenges in the biological shielding during the installation of high energy X-ray system for scanning vehicles containing suspected materials are discussed. The purpose of the present study is to develop a methodology for shielding design and evaluation for container scanner installations. The basic concept pertaining to shielding evaluation of radiotherapy installations provided in National Council on Radiation Protection and Measurements (NCRP)/International Atomic Energy Agency (IAEA) reports are referred, and appropriately used to calculate optimized shielding thicknesses requirements for container scanner installation. Workload is estimated based on number of containers scanned, machine ON time and dose rate at 1m. The shielding evaluation includes use of beam stopper in the primary beam, scattering by heterogeneous metallic scrap materials or any other suspected materials contained in the vehicle and their impact on the thickness of shielding walls. A model lay out plan to be used for installation of container scanner is developed. A methodology for shielding evaluation for various protective walls and ceiling of this model is also discussed. The study provides basic requirement for designing a structural room for installing 9MV container scanner from radiological safety view point.

Membangun Tembok Perlindungan Hak Asasi Manusia di Era Kejahatan Lintas Negara

Transnational crime is increasingly widespread in the era of globalization, presenting new challenges in protecting human rights (HAM). This article discusses the need to build a strong wall of human rights protection to combat transnational crime. Transnational crimes such as human trafficking, drug trafficking and terrorism have grown rapidly in the era of globalization. These crimes not only harm the affected countries, but also threaten the human rights of the victims. Transnational crime presents several challenges in protecting human rights. First, its cross-border nature makes law enforcement complicated. Second, the victims of these crimes are often intimidated and do not have access to justice. Third, the lack of international cooperation in fighting transnational crime. To overcome these challenges, it is necessary to build a strong human rights protection wall. Building a wall to protect human rights is a common task for all countries in the world. With strong cooperation and commitment, we can combat transnational crime and protect the human rights of victims.

Research on fence protection for liquid hydrogen leakage in the storage tank area

Hydrogen energy is an important carrier for energy terminals to achieve green and low-carbon transformation, but hydrogen safety remains a bottleneck for its large-scale commercial development. This study conducts numerical simulation of hydrogen leakage accidents in liquid hydrogen refueling stations, analyzes the shortcomings of protective walls in the safety aspect, and proposes the use of fences for protection. The results show that although the protective walls can prevent the cold hydrogen gas from diffusing outside the storage tank area, it greatly increases the duration and final dissipation time. Then gas cloud is prone to accumulate in corners. The fences can alter the turbulent field around the storage tank area, accelerate the heat exchange between cloud and air, and promote buoyancy. The promoting effect of fences on turbulence is most evident under windy conditions, especially outside the fence. Results indicate that the 3 cm and 4 cm fences have the best effect. Compared with the protective wall case, under windy conditions, the dissipation time of flammable clouds in the corner of the 3 cm fence is reduced by 8 s, while the 4 cm fence is reduced by 7 s. It should be noted that under wind conditions, the dilution time outside the 3 cm fence decreases by 21 s, while the 4 cm fence decreases by 35 s. Under windy conditions, there is a uniformly concentrated strong turbulent flow field near the 3 cm fence.

Lysine methyltransferase 2 plays a key role in the encystation process in the parasite Giardia lamblia

Histone post-translational modifications are extensively studied for their role in regulating gene transcription and cellular environmental adaptation. Research into these modifications has recently begun in the protozoan parasite Giardia lamblia, focusing on histone-modifying enzymes and specific post-translational changes. In the transformation from the trophozoite to the cyst form in the life cycle of this parasite, significant morphological and genetic alterations occur, culminating in the synthesis of cyst wall proteins responsible for forming the protective cyst wall. It has been previously demonstrated that histone deacetylation is required during encystation and that the enzyme lysine methyltransferase 1 is involved in the upregulation of encystation. Our study aims to extend the analysis to lysine methyltransferase 2 (GlKMT2) function. For this, two constructs were generated: one that downregulate the expression of GLKMT2 via antisense (glkmt2-as transgenic cells) and the other overexpressing GlKMT2 (glkmt2-ha transgenic cells). We found that the glktm2-as transgenic cells showed an arrest in progress at the late encystation stage. Consequently, the number of cysts produced was lower than that of the control cells. On the other hand, we found that the overexpression of GlKMT2 acts as a negative mutant of the enzyme. In this way, these glktm2-ha transgenic cells showed the same behavior during growth and encystation as glkmt2-as transgenic cells. This interplay between different enzymes acting during encystation reveals the complex process behind the differentiation of the parasite. Understanding how these enzymes play their role during the encystation of the parasite would allow the design of inhibitors to control the parasite.

ROUTE OF SOUTH SECTION OF BUDVA BYPASS - REVIEW OF PRELIMINARY DESIGN OF ORGANIZATION AND TECHNOLOGY CONSTRUCTION

<p class="ABSTRACT">The Budva bypass, spanning approximately 30 kilometers, is divided into three distinct sections: North, Middle, and South. The Terms of reference required the preparation of a Preliminary design for the construction elements of all structures along the section and route. The Southern section, which is the subject of this article, begins at the end of the Middle section in Vrijesno. The route of the Southern Section goes through the hilly hinterland above the Budva coast, from Kamenovo to Petrovac. In Petrovac, it is connected to the main road M-2 Petrovac-Sotonići-Virpazar via the intersection "Petrovac". The total length of the Southern section is 8.56km. There are five bridges and one tunnel in this route. There are, also, retaining structures and slope protection, conection routes and deviations, one interchange, and noise protection walls on this section of bypass. In this article, parts of Preliminary Design of organization and technology construction are showned. Network plan structure, approximate estimation of the duration of the works, approximate cost estimation, and approximate cash flow estimation during construction are presented.</p>

Theoretical Analysis of Drilling Unloading and Pile-Side Soil Pressure Recovery of Nonsqueezing Pipe Piles Installed in K0-Consolidated Soils

Drilling with prestressed concrete (DPC) pipe pile is a nonsqueezing pile sinking technology, employing drilling, simultaneous pile sinking, a pipe pile protection wall, and pile side grouting. The unloading induced by drilling, the pipe pile supporting effect, and the dissipation of the negative excess pore-water pressure after pile sinking, all of which have significant effects on the recovery of soil pressure on the pile side, are the main concerns of this study, which aim to establish a method to reasonably evaluate the timing selection of pile side grouting. The theoretical solutions for characterizing the unloading and dissipation of the negative excess pore-water pressure are presented based on the cylindrical cavity contraction model and the separated variable method. By inverse-analyzing the measured initial pore pressure change data from borehole unloading, initial soil pressures on the pile side of each soil layer are determined using the presented theoretical solutions. Then, the presented theoretical solutions were verified through a comparative analysis with the corresponding measured results. Moreover, by introducing time-dependent coefficients αt1 and αt2 to characterize the pore pressure dissipation and rheology effects, the effects of the negative excess pore-water pressure dissipation on the pile-side soil pressure recovery are discussed in detail.

Cold plasma‐assisted extraction of anthocyanin from purple corncobs and its antioxidant activity

AbstractIn this study, a novel radio‐frequency cold plasma‐assisted extraction (CPAE) process was developed for the extraction of anthocyanins from a type of agricultural biomass waste, purple corncob. The effects of cold plasma pretreatment on anthocyanin extraction were investigated, and this process was further optimized using response surface methodology. The components of purple corncob anthocyanins (PCAs) were analyzed by super‐high performance liquid chromatography‐mass spectrum. The antioxidant activity of PCAs was evaluated through 2,2‐diphenyl‐1‐picrylhydrazyl (DPPH) and 2′‐azinobis‐(3‐ethylbenzthiazoline‐6‐sulfonate) (ABTS) scavenging capacity assays in vitro and physiological behaviors in vivo for Caenorhabditis elegans. The results showed that the optimal conditions of cold plasma pretreatment were discharge power 127 W, working pressure 150 Pa, and the treatment time 75 s. The maximum yield of PCAs was about 4.05 ± 0.05 mg/g corncob, much higher than that of the conventional solvent extraction and ultrasonic‐assisted extraction. PCAs were mainly composed of pelargonidin‐3‐galactoside (66.02 wt.%), cyanidin‐3‐galactoside (25.95 wt.%), cyanidin (8.02 wt.%), and petunidin‐3‐galactoside (0.02 wt.%). The extracted anthocyanins reflected the superior antioxidant activity. In terms of in vitro antioxidant ability, the half maximal inhibitory concentration (IC50) of PCAs for DPPH and ABTS were slightly lower than those of ascorbic acid. Meanwhile, C. elegans exhibited positive effects on several physiological behaviors by feeding PCAs, including a 29.25% increase in lifespan, and increases in antioxidant capacity, superoxide dismutase, and catalase (CAT) activity of 26.28%, 28.93%, and 22.24%, respectively. The CPAE process is therefore a highly competitive candidate for the realization of industrial PCAs extraction, combining some additional advantages of cold plasma treatment such as green process, low cost, short treatment time, and scale‐up production.Practical applicationsAgricultural biomass wastes (e.g., corncob, straws, and husks) contain a large number of high value‐added natural active ingredients (e.g., polysaccharides, anthocyanins, and polyphenols). However, a highly efficient extraction of these natural active ingredients is always sought, as the protection of lignocellulosic cell walls hinders the extraction of intracellular products. In this work, the cold plasma‐assisted extraction (CPAE) process showed a comparatively higher anthocyanin yield than the conventional solvent extraction and ultrasonic‐assisted extraction processes. This was due to the fact that the high‐energy helium plasma attack readily broke down the lignocellulosic structure of the plant cell walls, resulting in the rapid release of intracellular purple corncob anthocyanins into the extraction medium. This study suggests that the CPAE process will become an emerging application for the industrial extraction of high value‐added natural active ingredients from agricultural biomass wastes.

High-temperature corrosion resistance of Fe–Cr–Mo amorphous coating for water wall protection of USC boiler

High-temperature corrosion resistance of Fe–Cr–Mo amorphous coating for water wall protection of USC boiler

Feasibility of Urban-Based Climate Change Adaptation Strategies in Urban Centers of Southwest Ethiopia: From Local Climate Action Perspective

This study identified the practices of adaptation strategies to climate change in Jimma, Bedelle, Bonga, and Sokorru urban centers using a survey of 384 households, 55 key informant interviews, 4 focus group discussions, and field observations. A cross-sectional study design was employed from 2019 to 2021. The adaptive capacity of municipalities to reduce climate extreme events was rated as poor by the majority (51%), mostly reactive measures (76%). The climate hazards identified in four urban centers were riverine and flash floods, urban heat waves, landslides, and windstorms. The urban households practiced lifestyle modification, reduce paved surfaces, the use of air conditioner, planting trees, and multiple windows. The adaptation strategies practiced by municipalities include the relocation of prone areas, the support of basic amenities, the construction of protection walls, diversion ditches, the clearance of waterways and rivers, greenery, and park development. The adaptation actions were constrained by a lack of awareness, commitment, cooperation and coordination, adaptive capacity, and participation. Gray/physical infrastructures (costly but important) as adaptation actions were hampered by the low municipal capacity. We recommend that urban authorities should incorporate climate change adaptation strategies into urban planning and development proactively to ensure future resilient climate smart urban centers of southwest Ethiopia.

Closed-form P-I diagram based on flextural and shear failure for ptotective wall

Protective walls are crucial structures in mitigating damage from explosions, particularly in environments such as gas refueling stations. However, evaluating their performance typically involves intricate numerical analyses to derive Pressure-Impulse (P–I) diagrams. This paper presents a novel closed-form solution for deriving P–I diagrams specifically tailored for protective walls, considering flexural and shear resistance. By assuming perfect plastic resistance, the proposed solution offers an efficient alternative to numerical analysis, particularly beneficial in preliminary design stages. The validity of the closed-form solution is demonstrated through comparisons with numerically derived P–I diagrams, showing promising results across various design parameters. This approach enhances the accessibility and ease of designing protective walls for blast resistance, contributing to improved safety measures in critical infrastructure.

Thermal-hydraulic and structural analyses of an additive manufactured panel mock-up for Wendelstein7-X

After the successful short pulse operation phase 1 (OP1) of the stellarator Wendelstein 7-X with maximal plasma energies of 200 MJ, the upcoming long pulse OP2 aims at stepwise higher energies up to 18 GJ. A series of the stainless steel wall protection panels is positioned behind the divertor pumping gaps for average stationary heat loads of 100 kW/m². These panels were produced by electron beam welding of stainless steel parts to build the housing of the cooling channels. This technology was more demanding than foreseen due the complicated 3D weld seams required by the shaping of the panels. An innovative technology which is more adapted to the panel geometry is additive manufacturing. It intends to bring significant advantages by printing the housing as a single piece without welds.The paper introduces the thermal-hydraulic and structural analyses of an additive manufactured panel mock-up performed with ANSYS V2022R2. The purpose of the calculation is to compare the thermal, hydraulic and structural performance of the improved design based on additive manufacturing and the present one. The welding process dictated the design of the cooling channel that induced local recirculation areas, additional local pressure drops, non well cooled areas for weld seams integration. In addition the weld strength assessment required special codes and methods, which cost more time and efforts. Without these constraints, additive manufacturing offers the opportunity of more freedom for the design of the cooling channel to reach better heat transfer performance of the panel.

The application of flexible and porous concrete structures in training works and scour protection

Concrete armour units such as Xbloc have been applied as armour layer for breakwaters and bank protections for years. These smartly shaped blocks were invented to offer efficient protection at more exposed locations by applying blocks that work together with neighbouring units to withstand high wave loads (Interlocking). Also material use was lowered since steeper slopes could be realized compared to conventional rock structures. Xstream and Xstone can be applied in a large range of applications that are traditionally built with loose rock, pitched rock or smooth block revetments such as: - Bed protection (e.g. offshore wind foundations) - River training works - Detached breakwaters - Quay wall protection in harbours - Revetment structures This abstract elaborates on why flexible and porous structures made of these small-scale [0.2 – 0.6m] concrete armour units are an interesting, low CO2 and eco-friendly alternative for bed protections and river training works.