Von Mises Stress Research Articles

Biomechanical characteristic differences of two new types of intramedullary nail devices in the treatment of comminuted intertrochanteric fractures of femur: a comparative study based on finite element analysis

ObjectiveGiven the recent application of two new types of intramedullary nail devices in the treatment of comminuted femoral intertrochanteric fractures (CFIFs), there is still a lack of deep understanding and comparative evaluation of their biomechanical properties. Therefore, this study aims to systematically compare the advantages and disadvantages of these two new devices with traditional proximal femoral nail antirotation (PFNA) and InterTan nails in the fixation of CFIFs through finite element analysis.MethodsBased on the validated finite element model, this study constructed an accurate CFIFs model. In this model, PFNA, InterTan nails, proximal femoral bionic nails (PFBN), and new intramedullary systems (NIS) were implanted, totaling four groups of finite element models. Each group of models was subjected to simulation tests under a vertical load of 2100 N to evaluate the displacement and Von Mises stress (VMS) distribution of the femur and intramedullary nail devices.ResultsUnder a vertical load of 2100 N, a comparative analysis of the four finite element models showed that the NIS device exhibited the most superior performance in terms of peak displacement, while the PFNA device performed relatively poorly. Although the NIS device had the highest peak stress in the femur, it had the smallest peak displacement of both the femur and intramedullary nail devices, and the peak stress was mainly concentrated on the lateral side of the femur, with significantly lower stress in the proximal femur compared to the other three intramedullary nail devices. In contrast, the PFBN device had the lowest peak stress in the femur, and its peak displacement of both the femur and intramedullary nail devices was also less than that of PFNA and InterTan nails.ConclusionThis study demonstrates that in the treatment of CFIFs, PFBN and NIS devices exhibit superior biomechanical performance compared to traditional PFNA and InterTan nail devices. Especially the NIS device, which can achieve good biomechanical results when fixing femoral intertrochanteric fractures with missing medial wall. Therefore, both PFBN and NIS devices can be considered reliable closed reduction and internal fixation techniques for the treatment of CFIFs, with potential clinical application value.

Influence of tool rotational speed in butt-joint friction stir welding (FSW): a thermo-mechanical simulation of AA6061

Friction Stir Welding (FSW) is a solid-state welding technique that involves joining two pieces of material by rotating a non-consumable pin at high RPM. This rotation generates heat through friction between the tool and the plates, enabling the welding process without the need for filler metal. Invented by the British Welding Institute (TWI) in 1991, FSW is renowned for creating strong welds and is widely used in the automotive and aerospace industries, in those industries the aluminum alloys are indispensable due to their unique combination of properties. This study focuses on how variations in rotational speed influence temperature distribution, the width of the heat-affected zone, and Von-Mises stress distribution in welded aluminum alloy 6061 sheets, this research aims to provide a comprehensive understanding of these effect, therefore the findings are expected to contribute to optimizing FSW parameters and enhancing weld quality. The analysis was conducted using the finite element method and ALTAIR software.

FINITE ELEMENT SIMULATION OF LOW-RISE SCHOOL BUILDING MODEL WITH SEISMIC LOADS INPUT

Earthquake impacts on buildings have garnered increased attention as Malaysia experiences seismic activities, notably from nearby regions like Sumatra and within areas such as Sabah. Despite this, current Malaysian design guidelines, such as BS 8110, do not fully incorporate seismic loads. This study addresses this gap by examining the structural performance of a scaled 1:8 model of a three-storey, low-rise school building under various peak ground accelerations (PGA) from 0.1g to 1.0g. Utilizing ABAQUS finite element simulation and time-history analysis, we evaluated the seismic responses, including local deformations, von Mises stress, and principal stresses. Key findings reveal a maximum structural displacement of 10.22 mm at 1.0g PGA, with significant stress concentrations observed at the column footings, highlighting critical areas for design improvement in seismic resilience.

Orthogonal cutting of 3D printed multi-material workpiece: numerical investigation of machining forces, stress, and temperature distribution

AbstractWith the development of 3D metal printers for rapid prototyping and industrial component production, heightened attention was directed towards post-processing operations for achieving precise surface quality and geometrical tolerances for these components. This paper investigated the orthogonal cutting of multi-material 3D printed workpieces using a coated cutting tool through finite element simulation. The workpieces featured different horizontal and vertical arrangements of layers composed of aluminum 7075-T6 alloy (Al), stainless steel 316 low alloy (SS), and Ti6Al4V alloy (Ti). The study explored the impacts of multi-material composition, coating thickness, and the rake angle of the cutting tool on machining forces, stress distribution, temperature distribution, and chip formation geometry. The results revealed a bimodal chip morphology in the machining process of horizontally arranged SS layers combined with other alloys. The SS layer resulted in a relatively uniform chip formation, while layers with two other materials exhibited a serrated chip formation. In contrast, a discontinuous chip formed when combining Al and Ti materials, as well as in the horizontally arranged layers made of Al, SS, and Ti alloys. The cutting force increased by 2.26 times when cutting workpieces with the horizontal arrangement of SS and Al layers compared to those with a single Al material. For the horizontal and vertical arrangement of layers made of Al and SS, von Mises stress values over the edge of the coated cutting tool significantly increased where the tool contacted the SS layer. Additionally, the horizontal arrangement of layers made of Al and SS materials caused the coated cutting tool to exhibit an extensive temperature distribution, with the maximum recorded temperature reaching 1448 °K. Increasing coating thickness led to a decrease in maximum principal stress at the surface of the tool and a rise in temperature at the cutting edge of the insert.

Patient-specific finite element analysis of four different fixation methods for transversely unstable radial head fractures

Plate fixation is a common treatment option for radial head fractures (RHFs). Due to the benefits of less invasiveness and fewer complications of internal fixation, the application of small-diameter headless compression screws (HCSs) to treat RHFs has become a new trend. This study aimed to compare the mechanical stability of four distinct internal fixation protocols for transversely unstable RHFs via finite element analysis. Using computed tomography data from 10 patients, we developed 40 patient-specific FE models of transversely unstable RHFs fixed by parallel, crossed, and tripod HCSs and mini-T plate (MTP). Under simulated physiological loading of the elbow joint, the construct stiffness, displacement, and von Mises stresses were evaluated and verified by a biomechanical experiment. Under shear loading, the MTP group exhibited lower construct stiffness, larger displacement, and higher Von Mises stress than the HCSs group. The stiffness of tripod HCSs was greater than parallel and crossed screw fixation techniques. There was a strong relationship between apparent bone density and construct stiffness (R = 0.98 to 0.99). In the treatment of transversely unstable RHFs, HCSs have superior biomechanical stability than MTP. The tripod technique was also more stable than parallel and crossed fixation.

Development of an improved limit pressure solution for shape-distorted 90o pipe bends with through-wall circumferential cracks

PurposeThis paper presents the approximate limit pressure solution for shape-imperfect and through-wall circumferential cracked (TWCC) 90° pipe bends at the intrados region. Finite element (FE) limit analysis was used to estimate the limit pressure by considering the small geometrical change effects.Design/methodology/approachThree-dimensional (3D) geometric linear FE methodology was implemented to investigate the limit pressure of structurally deformed TWCC 90° pipe bends. The material considered in the analysis is elastic perfectly plastic (EPP). The limit pressure of TWCC shape-distorted pipe bends was predicted from the corresponding internal pressure when von-Mises stress was equal to or just exceeded the material’s yield strength for all the models. The theoretical solution which was published in the literature was used to evaluate the current FE approach.FindingsOvality Co and TWCC at the intrados region caused a considerable impact on pipe bends, while the thinning? Ct produced a negligible effect and hence was not included in the analysis. With the combined effect, the bend portion of pipe bend experiences substantial influence, and the TWCC effect consequently increases with 45o, 60o and 90o crack angles and decreases the limit pressure of pipe bends. An improved closed-form empirical limit pressure solution was proposed for TWCC shape-distorted pipe bends at the intrados region.Originality/valueIn the limit pressure analysis of 90° pipe bends, the implications of structural irregularities (ovality and thinning) and TWCC have not been examined and reported.

Semi-automated finite element analyses of surgically treated acetabular fractures to investigate the biomechanical behaviour of patient-specific compared to conventional implants

BackgroundIn acetabular fracture surgery, understanding the biomechanical behaviour of fractures and implants is beneficial for clinical decision-making about implant selection and postoperative (early) weightbearing protocols. This study outlines a novel approach for creating finite element models (FEA) from actual clinical cases. Our objectives were to (1) create a detailed semi-automatic three-dimensional FEA of a patient with a transverse posterior wall acetabular fracture and (2) biomechanically compare patient-specific implants with manually bent off-the-shelf implants.MethodsA computational study was performed in which we developed three finite element models. The models were derived from clinical imaging data of a 20-year-old male with a transverse posterior wall acetabular fracture treated with a patient-specific implant. This implant was designed to fit the patient's anatomy and fracture configuration, allowing for optimal placement and predetermined screw trajectories. The three FEA models included an intact hemipelvis for baseline comparison, one with a fracture fixated with a patient-specific implant, and another with a conventional implant. Two loading conditions were investigated: standing up and peak walking forces. Von Mises stress and displacement patterns in bone, implants and screws were analysed to assess the biomechanical behaviour of fracture fixation with either a patient-specific versus a conventional implant.ResultsThe finite element models demonstrated that for a transverse posterior wall type fracture, a patient-specific implant resulted in lower peak stresses in the bone (30 MPa and 56 MPa) in standing-up and peak walking scenario, respectively, compared to the conventional implant model (46 MPa and 90 MPa). The results suggested that patient-specific implant could safely withstand standing-up and walking after surgery, with maximum von Mises stresses in the implant of 156 MPa and 371 MPa, respectively. The results from the conventional implant indicate a likelihood of implant failure, with von Mises stresses in the implant (499 MPa and 1000 MPa) exceeding the yield stress of stainless steel.ConclusionThis study presents a workflow for conducting finite element analysis of real clinical cases in acetabular fracture surgery. This concept of personalized biomechanical fracture and implant assessment can eventually be applied in clinical settings to guide implant selection, compare conventional implants with innovative patient-specific ones, optimizing implant designs (including shape, size, materials, screw positions), and determine whether immediate full weight-bearing can be safely permitted.

Influence of connection design and material properties on stress distribution and fatigue lifetime of zygomatic implants: A finite element analysis

Zygomatic implants (ZIs) were developed as a graftless alternative to rehabilitate severely reabsorbed maxillae. This study aims to employ three-dimensional finite element analysis (FEA) to simulate the impact of external hexagonal implant connection (EHC) and internal hexagonal implant connection (IHC) on the stress distribution and fatigue lifetime within the ZI systems using parameters defined in ISO 14801:2016. Two ZI assemblies (Nobel Biocare and Noris Medical) were scanned in a micro-CT scanner and reconstructed using Nrecon software. Three-dimensional models were generated by Simpleware ScanIP Medical software. All models were exported to FEA software (ABAQUS) and subsequently to a fatigue analysis software (Fe-safe). A compressive 150 N load was applied at a 40° angle on the cap surface. A 15 Hz frequency was applied in the in silico cyclic test. The implant components had material properties of commercially pure grade 4 titanium (CPTi) and Titanium-6Aluminum-4Vanadium alloy (Ti64). Von Mises stress data, contour plots, and fatigue limits were collected and analyzed. EHC models exhibited higher peak stresses in implant components for both materials compared to IHC models. However, simulated bone support results showed the opposite trend, with higher stresses on IHCthan EHC models. The fatigue analysis revealed that assemblies with both designs exceeded ISO 14801:2016 number of cycles limits using Ti64, while CPTi groups exhibited comparatively lower worst life-repeats. In conclusion, ZIs with IHC were found to have a more homogeneous and advantageous stress distribution within both materials tested. Ti64 demonstrates a prolonged service life for both design connections.

Comparison of stress distribution around splinted and nonsplinted implants with different crown height space in posterior mandible: A finite element analysis study.

The purpose of this finite element analysis (FEA) study was to analyze the stress distribution on prosthetic components of splinted and nonsplinted prostheses, bone, and implants with different crown height space (CHS). Mandibular posterior segment was modeled with no resorption at the second premolar site and various amounts of resorption (0, 3, 6, and 9mm) at the first molar site. Two adjacent implants (Straumann bone level implants, 4.1 mm×8mm) were placed; at the second premolar site, the crown height was 8mm and at the first molar site, the crown height varied (8, 11, 14, and 17mm), depending on the amount of resorption. Both splinted and nonsplinted crowns were designed. Vertical and oblique loads of 400 N were applied to the crowns. von Mises stress was used to evaluate the stress distribution in the implant complex and maximum principal stress was used to evaluate the stress in the bone. When oblique forces were applied, the highest von Mises stresses were observed for nonsplinted crowns in the 17mm CHS group. The maximum principal and minimum principal stresses observed in bone under oblique loading increased with increased CHS for nonsplinted restorations. Crown height affected the amount of stress in bone and implant components. When the crown height difference between two adjacent implants increases, splinting may be crucial.

Effect of Sclerosis Bands in Femoral Head Necrosis on Non-Vascularized Fibular Grafting-A Finite Element Study.

Femoral head necrosis is a challenging condition in orthopaedics, and the occurrence of collapse is an important factor affecting the prognosis of femoral head necrosis. Sclerosis bands are known to influence the collapse of the femoral head, yet there is a lack of research on the biomechanical role of sclerosis bands in non-vascularized fibular grafting surgery. This study aims to evaluate the biomechanical impact of sclerosis bands in femoral head necrosis and their role in non-vascularized fibular grafting surgery (NVFG) using finite element analysis. We constructed 11 finite element models based on CT scan data of a normal hip joint, simulating different sclerosis band thicknesses and defect scenarios. The models were analyzed for changes in femoral head displacement and von Mises stress. We constructed a hip joint model based on CT data from a normal hip joint, and after reconstruction, assembly, and optimization using 3-matic. We created five groups consisting of 11 finite element analysis models of the hip joint. Mesh partitioning and mechanical parameter settings were performed in ANSYS. The changes and differences in femoral head displacement and von Mises stress of these models were analyzed. Increasing sclerosis band thickness led to reduced peak displacement of the femoral head by 28.6%, 42.9%, and 47.6%, and increased surface von Mises stress by 28.3%, 13.8%, and 13.0%, respectively. Post-surgery, peak displacement decreased in all groups compared to pre-surgery levels. Increasing sclerosis band thickness post-surgery resulted in decreased maximum von Mises stress of the femoral head by 13.9%, 3.0%, and 8.1%. Defect volume in the defect groups correlated with increased peak displacement of the femoral head by 10.0%, 30.0%, and 100.0%, and increased surface maximum von Mises stress of the femoral head by 9.3%, 14.0%, and 15.1%. Sclerosis band formation exacerbates von Mises stress concentration on the femoral head surface. However, thicker sclerosis bands improve post-NVFG stability and mechanical performance. Larger anterior lateral sclerosis band defects significantly compromise postoperative stability, increasing the risk of collapse. Protecting the anterior lateral sclerosis band during NVFG surgery is crucial.

Biomechanical difference analysis of new and classic intramedullary nail devices in the treatment of basal femoral neck fractures: finite element analysis

ObjectiveThere is currently a lack of in-depth comparative evaluation regarding the biomechanical properties of novel intramedullary nail devices in the treatment of basal femoral neck fractures (BFNF). This study aims to utilize finite element analysis to compare the performance differences of two novel devices with traditional PFNA and InterTan nails in the fixation of BFNF.MethodsBased on a validated finite element model, this study constructed an accurate BFNF model and implanted four different intramedullary nail devices: PFNA, InterTan nail, PFBN (proximal femoral biomimetic nail), and NIS (novel intramedullary system). Under a vertical load of 2100N, the displacement and Von Mises stress (VMS) distribution of each group of models were evaluated through simulation testing.ResultsUnder a load of 2100N, the PFBN device exhibited the best performance in terms of displacement and peak stress, while PFNA performed poorly. The peak displacement of the NIS device was lower than that of PFNA and InterTan nails, while the peak stress of the InterTan nail was lower than that of PFNA and NIS.ConclusionThe PFBN device demonstrates stronger load-bearing and shear-resistant properties in the treatment of BFNF, and the NIS device also shows significant improvement in stability. Therefore, both the PFBN and NIS devices are reliable internal fixation techniques for the treatment of CFIFs, with potential clinical application prospects.

Reliability analysis of 50000 kN hydraulic support test bench under shrinkage test conditions

The large mining-height hydraulic support test-bed serves as a crucial tool for heavy hydraulic support factory inspections and type testing. With the successful development of the ZY29000/45/100D hydraulic support, the need for a large high-mining hydraulic support test-bed has become evident. This paper combines the theory of rigid-flexible coupling in virtual prototypes and ADAMS multi-body dynamic simulation technology to analyze the strength of the 50,000 kN hydraulic support test-bed. ANSYS classic modules were employed to address the flexibility of key components within the test-bed. The fatigue life of the test-bed was analyzed using NSOFT software, the von Mises yield criterion, and the Goodman modified curve. The S-N curve of material parameters for the test-bed components was used to conduct a shrinkage test. The results indicate that the lowest position is the most vulnerable during the shrinkage test. Among the key components, the stress on the pin bearing is 356.6 MPa, which is 167.9 %, 123.3 %, and 41.6 % higher than that of the pillar, movable beam, and base, respectively. The fatigue life of the base under low, medium, and high shrinkage conditions is1.1×107, 4.0×108, and 1.7×108, with damage values of 8.8×10-8, 2.5×10-9, and 5.7×10-9, respectively. The base’s life under low shrinkage conditions is the shortest, followed by that under high shrinkage conditions. These research findings provide technical guidance and an optimization foundation for the successful development of a 50000 kN hydraulic support test-bed. They also offer a new method and approach for analyzing and predicting the fatigue life of key components in large-scale industrial and mining equipment operating under complex conditions, with promising practical applications.

Comparative Biomechanical Study of Different Screw Fixation Methods For Minimally Invasive Hallux Valgus Surgery: A Finite Element Analysis

BackgroundThere are different screw configurations utilised for minimally invasive hallux valgus (HV) deformity despite limited biomechanical data assessing the stability and strength of each construct. We aimed to compare the strength of various screw configurations for minimally invasive HV surgery using finite element analysis (FEA). MethodsA FEA model was developed from a CT of a female with moderate HV deformity. Five screw configurations utilizing one or two bicortical or intramedullary screws were tested. Stress analysis considered osteotomy displacement, maximum and minimum principal stresses, and von Mises stress for both implants and bone for each screw configuration. ResultsFixation with two screws (one bicortical and one intramedullary) demonstrated the lowest values for osteotomy displacement, minimum and maximum total stress, and equivalent von Mises stress on the bone and screws in both loading conditions. ConclusionThe optimal configuration when performing minimally invasive surgery for moderate HV is one bicortical and one intramedullary screw. Level of evidenceLevel III

Comparative Evaluation of Stress Distribution and Deformation in Class II Cavities Restored With Two Different Biomimetic Restorative Materials: A Three-Dimensional Finite Element Analysis.

Aim This study aims to comparatively evaluate the stress distribution and deformation in class II cavities restored with EverX posterior and ActivaTMBioactive restorative material using three-dimensional finite element analysis. Methods On a mandibular first molar tooth model, features of a class II mesio-occlusal cavity were designed. Following the application of EverX Posterior and ActivaTMBioactive, the model was subjected to a 600 N static occlusal load. Three-dimensional finite element analysis was used to analyze the distribution of occlusal stresses among the remaining components and restorative materials. von Mises and maximum principal stresses were evaluated and compared. Results von Mises and maximum principal stresses of ActivaTMBioactive components were higher compared to the control group and EverX Posterior model. ActivaTMBioactive restorations had absorbed more stresses within the material rather than distributing it to enamel and dentin than EverX Posterior material. Also, deformation was extremely high in the ActivaTMBioactive model, which may be because of less stiffness of the material. Conclusion EverX posterior has a higher capacity to bear stresses in stress-bearingareas than ActivaTMBioactive Restorative.

Biomechanical differences of three cephalic fixation methods for patients with basilar invagination and atlantoaxial dislocation in the setting of congenital atlas occipitalization: a finite element analysis

Background contextIn cases of basilar invagination-atlantoaxial dislocation (BI-AAD) complicated by atlas occipitalization (AOZ), the approach to cranial end fixation has consistently sparked debate, generally falling into two categories: C1–C2 fixation and occipitocervical fixation. Several authors believe that C1–C2 fixation carries a lower risk of fixation failure than occipitocervical fixation. PurposeTo study the biomechanical differences among 3 different cranial end fixation methods for BI-AAD with AOZ. Study designThis was a finite element analysis. Patient sampleA 35-year-old female patient diagnosed with congenital BI-AAD and AOZ. Outcome measuresrange of motion (ROM), peak von Mise stress (PVMS), cage micro-subsidence, cage micro-slippage MethodFour finite element models were constructed, including unstable group (BI-AAD with AOZ), C1 lateral mass screw group, occipital plate group, occipitocervical rod group. The flexion and extension (FE), lateral bending (LB) as well as axial rotation (AR) were simulated under a torque of 1.5 Nm. Parameters include C1–C2 ROM, PVMS on screw-rod construct, cage micro-subsidence, cage micro-slippage. ResultsThe ROM of the C1 lateral mass screw group was smaller than that of the other fixation groups in LB and AR, but not FE. Compared with the occipitocervical rod group, the ROM in LB and AR of the occipital plate group was higher, but not in FE. The PVMS of C1 lateral mass screw group was significantly higher than that of the other groups. The ROM and PVMS of the occipitocervical rod group were in between the other 2 groups. Regarding the screws at the cranial end, the PVMS of the 4-screw occipitocervical rod group was significantly lower than that of the other groups. In general, the cage micro-motion follows the ascending order: C1 lateral mass group < occipitocervical rod group < occipital plate group. ConclusionIn cases of BI-AAD with AOZ, the C1 lateral mass screw group provided the least ROM and cage micro-motion, but the screw-rod PVMS was the largest. The advantage of occipital plate fixation lies in the lowest screw-rod PVMS, but the ROM and cage micro-motion is the highest. Four-screw fixation at the cranial end of occipitocervical rod group helps to reduce the PVMS and may prevent screw failure at the cranial end.

Topology Optimization Driven Bone-Remodeling Simulation for Lumbar Interbody Fusion.

This study proposes a numerical approach for simulating bone remodeling in lumbar interbody fusion (LIF). It employs a topology optimization method to drive the remodeling process and uses a pixel function to describe the structural topology and bone density distribution. Unlike traditional approaches based on strain energy density or compliance, this study adopts von Mises stress to guide the remodeling of LIF. A novel pixel interpolation scheme associated with stress criteria is applied to the physical properties of the bone, directly addressing the stress shielding effect caused by the implanted cage, which significantly influences the bone remodeling outcome in LIF. Additionally, a boundary inverse approach is utilized to reconstruct a simplified analysis model. To reduce computational cost while maintaining high structural resolution and accuracy, the Scaled Boundary Finite Element Method (SBFEM) is introduced. The proposed numerical approach successfully generates results that closely resemble human lumbar interbody fusion.

Evaluation of the forces applied by rubber dam clamps on mandibular first molar teeth with different endodontic access cavities: a 3D FEA study.

This study aimed to examine the effect of the force applied by rubber dam clamps made from different materials on mandibular first molar teeth with various designs of endodontic access cavities using finite element analysis. A intact tooth (IT) and seven different endodontic access cavities namely, a traditional endodontic cavity (TRADAC), a guided endodontic cavity (GEC), a conservative endodontic cavity (CAC), an ultra-conservative access cavity (UAC), a truss access endodontic cavity (TRSAC), a mesial caries access cavity (MCAC), and a distal caries access cavity (DCAC), along with two different clamp finite element models, were created. The clamp models were made of polyether ether ketone (PEEK) and stainless steel (SS). The forces applied by the clamps were calculated based on the axial section distance of the tooth, and these forces were applied to the contact areas on the tooth. Stress distribution models were calculated using maximum von Mises (vM) stress. The lowest vM stress under the forces applied by the SS and PEEK clamps was found in the IT model (80.914 MPa) with the PEEK clamp. The highest vM stress was found in the DCAC model (759.49 MPa) applied with the SS clamp. The forces applied by SS clamps resulted in higher vM stress values in every cavity design than those applied by PEEK clamps. PEEK clamps generated less force than SS clamps. However, clinicians should follow various isolation strategies (clamp made of different materials, split dam, etc.) according to different cavity types of the tooth.

A finite element analysis on the indication for extracting partially impacted mandibular third molars considering mandibular trauma

BackgroundPatients presenting with partially impacted lower third molars (M3) have a higher likelihood of experiencing angle fractures while simultaneously decreasing the risk of condylar fractures. However, the specific biomechanical mechanism responsible for this occurrence remains unclear. Moreover, there is an ongoing debate regarding whether the removal of M3s might actually increase the risk of condylar fractures. This study aimed to evaluate how the presence of M3s influences mandibular fractures resulting from blows to the symphysis and lateral mandibular body, and to determine the indication for extracting M3s in such cases.MethodsModels of the mandible with a partially M3-impacted model (M3I), M3-extracted model (M3E), and M3-absent model (M3A) were generated using a computer. A traumatic blown force of 2000 N was applied to the symphysis and the right body of the mandible. Von Mises and principal stresses were analyzed, and failure indexes were determined. Two cases of mandibular linear fractures were chosen for model verification and interpretation.ResultsWhen force was applied to the symphysis, the condylar region exhibited the highest stress levels, while stress in the mandibular angle region was much less regardless of the M3 state. On applying the force to the right mandibular body, stress in the condylar region decreased while stress in the mandibular body increased, especially in the blown regions. Impacted tooth or cavity formation post-M3 extraction led to uneven stress distribution on the blown side of the mandible, increasing the risk of mandibular angle fractures. In cases where M3 was absent or the extraction socket had healed, stress from lateral traumatic blown force was evenly distributed along both the inner and outer oblique lines of the mandible, thereby reducing the risk of mandibular fractures.ConclusionsThe reduced risk of condylar fractures in patients with partially impacted lower M3s and mandibular angle fractures is mainly due to lateral blows on the mandible, which generate less stress in the condylar region than blows on the mandibular symphysis, rather than being caused by the M3 itself. Extraction of the lower M3 can decrease the risk of mandibular fractures, with a minor influence on condylar fractures.

A multifaceted approach using RVE homogenization methodology for identification of elastoplastic behavior of steel matrix composite: Application to deep-drawing process

The integration of cutting-edge materials and computational methods is now essential in contemporary engineering, especially in sectors where a deep comprehension of the mechanical behavior of reinforced composite materials is crucial. In this context, steel matrix composites, enhanced with reinforcing elements like TiB2, have garnered attention due to their potential for superior mechanical properties and wide-ranging applications. This article explores an innovative computational framework based on the Representative Volume Element (RVE) concept to examine the elastoplastic properties of a ferritic steel matrix reinforced with ceramic particles (TiB2). The finite element analysis (FEA) is performed with periodic boundary conditions (PBCs) to apply the specified loading to the RVE. As a first endeavor, the developed multi-faceted approach provides a broader perspective on shear behavior and the elastoplastic composite’s properties of Fe-TiB2 for various reinforcement volume fractions. Then, the focus of this study lies in its application to the deep-drawing process, a critical manufacturing operation with significant implications in industries such as automotive and aerospace. The established approach for homogenizing elasto-plastic Fe-TiB2 composites is applied to analyze the influence of reinforcement variation on several critical aspects during the deep-drawing process, including formability, forming force, Von Mises stress distribution, and logarithmic strain.

Adaptive circumferential distance location of the laser energy beam in the laser-assisted turning of Al/SiC metal matrix composites

Laser-assisted turning (LAT) involves locally heating a rotating workpiece using a focused laser beam before the removal of material. A key aspect in optimising productivity with laser-assisted turning is understanding the thermal relationship between laser heating, the improved material removal rate, and machinability. Consequently, in this paper, a thermal heating and laser-assisted turning finite element model and experiments were conducted to assess the machinability of an Al/SiCp MMC workpiece, considering the circumferential location of the laser beam from the cutting point. The results confirm that laser power and cutting velocity influence the temperature profile from the laser spot to the tool point and the heat-affected depth. Positioning the cutting tool closer to the laser spot effectively reduces the Von Mises stress during cutting at higher cutting temperatures. At the same time, the experiment indicates an increased risk of directly heating the tool, which can affect the integrity of the cutting tool. The work further reveals that at specified cutting velocities, lower specific cutting energy improves the tool condition and surface quality of the machined parts. Based on a range of material removal rates and laser-specific energy density, a new criterion for optimal laser-tool circumferential distance was determined. Establishing this distance can act as a guide for the laser-assisted turning of Al/SiCp metal matrix composites and potentially other materials.