Voltage Multiplier Cell Research Articles

Analysis and implementation of modified quadratic boost high-gain converter using voltage multiplier cell

Analysis and implementation of modified quadratic boost high-gain converter using voltage multiplier cell

Ultra-high voltage gain achieved with quadratic DC/DC converter design

This work introduces a novel DC/DC converter with an incredibly high voltage gain, specifically designed for renewable energy generating systems. The proposed circuit features a coupled inductor integrated with a quadratic boost circuit and a voltage multiplier cell to achieve a substantial step-up in voltage gain. Ultra-high voltage gain, minimum reverse recovery in diodes, low voltage stress on switching devices, continuous input current, and a shared ground between the input source and output load are some of this topology’s key features. The coupled inductor design reduces power dissipation in magnetic components by distributing the high DC source current with an additional input inductor. Additionally, regenerative clamp circuits alleviate voltage stresses on power switches during simultaneous switching. Theoretical analysis covering the operating principle, steady-state behavior, and efficiency is discussed in detail. An evaluation of the suggested topology’s performance is conducted using a 250-W, 25-V/400-V lab prototype.

An ultra-high gain boost converter with low switching stress for integrated multi-energy storage systems

In this paper, a high-gain low-switching-stress coupled-inductor with high voltage step-up voltage multiplier cells quadratic boost converter (VMC-QBC) is proposed. The turn ratio of the coupled inductors and the switch duty cycle increase the dynamic gain, and the two degrees of freedom adjustment and modularity of the voltage multiplier cells (VMC) make the structure more flexible. The use of the same drive signal for both switches makes control easier. While achieving multi-stage boosting and multiplication boosting from low to medium duty cycle, the passive clamping circuit absorbs the energy leaked by the coupled inductor, thus reducing the stress on the switching tube and alleviating the diode reverse recovery problem. A non-ideal model with parasitic parameters is developed to analyse the real voltage gain and the converter losses to give design guidelines. A 300 W prototype is designed and tested. The state space model of the converter is established and the working principle is analysed. Compared to other high-gain quadratic boost converters, the proposed converter has continuous input current, common ground characteristics, and high voltage gain at low to medium duty cycles to accommodate integrated multi-energy storage systems.

Design of a high voltage gain converter using coupled inductor with reduced voltage stress for photovoltaic energy based systems

This paper presents the design and analysis of a high voltage gain converter utilizing a coupled inductor with reduced voltage stress, specifically for photovoltaic energy-based systems. The proposed converter employs a two-winding coupled inductor and voltage multiplier cells to achieve an increase in output voltage while mitigating voltage stress across semiconductor components. Additionally, the voltage multiplier cells function as voltage clamps for the power switch, further enhancing the converter's performance. The converter features a single switch design, which simplifies control, reduces cost, and improves reliability. Key advantages of the converter include a low component count, a common ground between input and output ports, and high efficiency. The converter's performance is thoroughly investigated through mode analysis and steady-state analysis. Comparative evaluations with similar converters are conducted to highlight the benefits and performance of the proposed design. To validate the theoretical analysis, a 125 W prototype with 26 V input and 200 V output voltages operating at a 50 kHz switching frequency is developed, and experimental results are presented, demonstrating the effectiveness and practicality of the proposed high voltage gain converter.

An improved voltage gain bidirectional DC/DC converter based on voltage multiplier cell for electric vehicle application

ABSTRACT The global energy crisis has raised environmental concerns, leading governments to invest in renewable energy and address electric vehicle (EV) and hybrid EV (HEV) difficulties. One of the main challenges is the interface between the energy storage system and the DC-link of the three-phase inverter. For this aim, an improved voltage gain bidirectional DC/DC converter based on a voltage multiplier cell (VMC) is proposed in this paper, which acts like a high boost converter when the energy storage system is powering the EV and a buck converter when regenerative braking is required. The proposed bidirectional converter has advantages like low device account, simple structure, reduced switching power losses, high voltage gain, common ground, and increased efficiency. An output voltage of 10 times the input voltage in boost mode is provided by the proposed converter. Also, the proposed converter can generate a voltage 0.26 times lower than the input voltage in buck mode. The operating principle and comparative analysis with other existing converters are presented. Moreover, the efficiency calculation is discussed by assuming the non-ideal parameters. The proposed converter has a maximum efficiency of 97.78%. Finally, a 500 W simulation prototype is implemented in PSIM software to confirm the theoretical analysis.

Design of low‐stress ultrahigh‐gain dc–dc converter with coupled inductor

AbstractThe dc–dc converter plays a vital role in renewable energy power generation systems. To enhance the boost range and supply stable output voltage for the power grid, This paper propose an improved low‐stress ultrahigh‐gain dc–dc converter. First, a voltage multiplier cell is designed stemming from a three‐winding coupled inductor and a switched capacitor (SC), which can obtain ultrahigh voltage gain. In the improved voltage multiplier cell, the number of semiconductor devices is reduced, resulting in a decrease in capacitor voltage stress. Moreover, a passive clamp circuit uses the new SC, which can suppress oscillation peak voltage and absorb the leakage energy of the coupled winding. Furthermore, we deduce the operating mode of the proposed converter . Compared with other advanced topologies, the proposed topology outperforms boosting capacity, component stress, and efficiency. To stabilize the output voltage, the converter is closed‐loop controlled. Finally, experiments on the 180 W prototype have demonstrated the reliability and effectiveness of the proposed topology.

A ZVS High Step-Up DC–DC Converter With Three-Winding Coupled-Inductor Assisted Voltage Multiplier Cell Suitable for Renewable Energy Systems

A ZVS High Step-Up DC–DC Converter With Three-Winding Coupled-Inductor Assisted Voltage Multiplier Cell Suitable for Renewable Energy Systems

A novel soft‐switching quadratic high voltage gain trans‐inverse DC/DC converter

AbstractThis paper suggests a new non‐isolated high step‐up DC/DC converter with soft‐switching performance and low input current ripple for renewable energy generation systems. In this introduced circuit, a three‐winding coupled‐inductor combined with a quadratic boost circuit and voltage multiplier cell to obtain high voltage gains. The advanced features of the proposed topology are its ultra‐high voltage gain, soft‐switching performance, low voltage stress across the switching components, continuous input current with low ripple, and the existence of a common ground between the input source and output load. Due to the partial trans‐inverse property in the suggested topology, higher voltage gains can be achieved under smaller turns ratios of the coupled in comparison to the other typical topologies, which leads to efficiency improvement. Moreover, in this introduced circuit, the voltage stress on the single power switch is mitigated using a regenerative clamp circuit. The theory and operating principle of the suggested converter, along with the steady‐state analysis and efficiency interpretation of the proposed converter are discussed in detail. Finally, to verify the theoretical analysis, a 200 W (25 V/400 V) sample prototype is established.

Interleaved High Voltage Gain DC-DC Converter with Winding-Cross-Coupled Inductors and Voltage Multiplier Cells for Photovoltaic Systems

An interleaved high voltage gain DC-DC converter with winding-cross-coupled inductors (WCCIs) and voltage multiplier cells is proposed for photovoltaic systems. The converter configuration is based on the interleaved boost converter integrating the diode-capacitor clamp circuits, the winding-cross-coupled inductors, and voltage multiplier cells to increase the voltage gain and reduce the semiconductor voltage stresses. The equal current sharing of two phases is achieved with the help of the winding-cross-coupled inductors. The converter achieves high voltage gain while operating at a proper duty ratio. The low-voltage-rated MOSFETs with low on-resistance are available to reduce the conduction losses due to the low switch voltage stress. The leakage energy of the coupled inductors is recycled such that the voltage spikes on the power switches are avoided. The input current ripple is decreased due to the interleaved operation. The operating principle and steady-state analysis of the proposed converter are proposed in detail. The design guidelines of the proposed converter are given. In addition, the closed-loop controlled system of the proposed converter is designed to diminish the effect of the variations in input voltage and load on the output voltage. Finally, the experimental results of a 1000 W converter prototype with 36 V input and 400 V output are given to validate the theoretical analysis and the converter performance.

A High Step-Up Resonant Converter Based on Current-Fed Voltage Multiplier Technique

An extendable non-isolated resonant dc-dc converter based on current-fed voltage multiplier (VM) technique is proposed in this paper for high step-up applications. These VM cells capacitors participate in a resonant network; therefore, no additional elements are required to provide a resonant tank circuit to realize soft switching conditions for power switches. Zero voltage switching (ZVS) and zero current switching (ZCS) conditions are realized here for switches and diodes, respectively. Consequently, MOSFETs dominant switching losses and the diodes reverse recovery problems are well overcome. Furthermore, the input source current waveform is continuous. Also, using the VM cells reduces the power devices voltage stresses. Accordingly, low voltage rating devices can be used, which reduce conduction losses and cost, and improve the converter efficiency. Also, by using more VM cells, the proposed converter can be used for high-voltage applications, without using extremely high duty cycle values to regulate the output voltage. The operation principles, steady-state analysis, design guidelines, and main characteristics of the proposed converter are given here, in detail. Finally, an 800 W prototype converter, with 80–100V input voltage and 2 kV output voltage, has been implemented to validate the given analyses, simulation results, as well as to show the proposed converter main advantages.

An Improved High Gain Continuous Input Current Quadratic Boost Converter for Next–Generation Sustainable Energy Application

With the rapid transformation from fossil fuel-based energy systems to renewable-based energy systems the application of a high gain boost DC-DC converter is becoming the main attraction due to its wide range of numerous applications. This specific study presents an improved high gain non isolated quadratic boost DC-DC converter (QBC) with voltage gain three times of the quadratic boost converter. The proposed non-isolated category topology is the modified version of the quadratic boost converter where the 2nd inductor of the QBC is replaced by a voltage multiplier cell (VMC) and a switch capacitor network is integrated with the VMC to increase the voltage gain as well as to reduce the switch’s voltage stress. Moreover, the continuous input current and common ground feature of this proposed circuit configuration have shaped its potential application by making it advantageous over other non-isolated based high gain boost converters. To support its feasibility a rated power of 150 W prototype is developed after validating the results by Plecs software. The voltage gain offered by this proposed circuit configuration is justified by experimental results and the software simulation. A comprehensive analysis and components design is also formulated and documented in this study.

A high step-up soft-single switched converter with three coupling inductors

ABSTRACT This paper presents a new high voltage gain converter, which bases on the incorporation of the voltage multiplier cell and the switched coupled inductor technique, having low voltage stress on the switch, which is far from the output voltage. The presented topology is well suited for high step-up applications. By integrating coupled inductors and voltage multiplier cell techniques, a high step-up voltage gain is achieved. All of the semiconductor devices are switched under soft switching conditions, which reduces the switching losses significantly. The switch turns on at ZCS and turns off at ZVS. All diodes have soft-switching features and their reverse recovery problem is obviated due to the leakage inductance. The operation principles and theoretical analysis of proposed converter are presented in details. At the end, the experimental results have been taken from a laboratory prototype rated at 100 W, input voltage of 24 V, output voltage of 300 V, and switching frequency of 100 kHz.

An analytical design and analysis of a high gain switched inductor voltage multiplier cell power converter

The proposed modified higher gain boost converter employs switched Inductor and multiplier cell-based voltage boosting techniques, as the paper represents. This converter is modelled to enhance the static gain and efficiency. As the designed topology has an incessant source current at its input side, it is ideal for solar PV applications. With a power capacity of 100 W, the proposed topology is designed to work on 24 V source input and 200 V load/output voltage. The load voltage is maintained by a PI controller, which achieves the highest efficiency of 92% under rated load conditions. The converter’s transient performance with the controller is investigated under various situations, including supply voltage variation, reference voltage variation, and load power variation. Finally, the designed converter’s experimental model is created to evaluate the simulated and conceptual results.

High Voltage Step-Up Boost Converter Based on a Three-Winding-Coupled Inductor With Voltage Multiplier Cell

High Voltage Step-Up Boost Converter Based on a Three-Winding-Coupled Inductor With Voltage Multiplier Cell

Ultra-High Gain Quadratic DC-DC Topology Using Two-Winding Coupled Inductors With Voltage Multiplier Cells

Ultra-High Gain Quadratic DC-DC Topology Using Two-Winding Coupled Inductors With Voltage Multiplier Cells

Design and Analysis of a New High Step-Up Converter Using Switched-Inductor-Capacitor Voltage Multiplier Cells for Photovoltaic Application

Design and Analysis of a New High Step-Up Converter Using Switched-Inductor-Capacitor Voltage Multiplier Cells for Photovoltaic Application

An ultra‐high voltage gain interleaved converter based on three‐winding coupled inductor with reduced input current ripple for renewable energy applications

AbstractThis article proposes an interleaved high step‐up DC–DC converter topology designed for renewable energy applications, featuring an ultra‐high voltage conversion ratio. The converter employs an interleaved structure, resulting in a low peak‐to‐peak ripple in the input source current, which is particularly advantageous for solar PV sources. To enhance the output voltage, the topology utilizes voltage multiplier cells (VMC) and coupled inductor techniques. Two coupled inductors with three windings are integrated into the proposed topology, with the secondary and tertiary windings combined with VMC. This combination effectively reduces the maximum voltage stress across power switches, enabling the use of low‐rated and cost‐effective power switches for implementation. The article offers comprehensive operation modes and steady‐state analyses to demonstrate the converter's performance. A comparison is made between the suggested structure and other similar converter topologies. To validate the mathematical analysis, a 200‐W prototype is constructed, operating at a frequency of 25 kHz and achieving a voltage conversion range of 20 to 409 V. The experimental results are presented to support the findings.

A novel multi-input medium-gain DC-DC boost converter with soft-switching performance

This paper proposes a new non-isolated dual-input zero-voltage switching (ZVS) dc-dc boost converter with medium voltage gain. Two input ports of the converter are current-fed and suitable for a unidirectional dc power source, and a chargeable dc energy storage. The proposed converter basic circuit composed of three cascaded power switches, which at their connection points join to the converter three inductors and a switched capacitor voltage multiplier (VM) cell is accompanied. Using this VM cell the converter voltage gain achieves two times of that in the conventional boost converter and also half voltage stress across the power switches. Through the converter two input inductors powers from a unidirectional source (like PV) and a chargeable battery source can be accepted. Taking a triangular resonant current at the switching frequency, the converter third inductor aids to reach ZVS for the power switches. The converter power switches turn-on with ZVS and the power diodes stop conducting with ZCS in all operation conditions. As a result, low switching power losses, reduced reverse recovery issue, and high efficiency are accessible especially for higher input and output powers. The converter power switches are switched in PWM manner with two individual duty ratios, allowing to regulate the output voltage and control the extracted power from the input unidirectional port. The proposed circuit has been analyzed in detail to find its different operating modes, determine its capacitor currents, estimate its power losses components and design its control system. Behavior of the proposed system is also examined by a low-power laboratory prototype tested under four different practical operation conditions. The proposed converter benefits from simple and compact structure, current-fed input ports, low number of power switches and magnetic elements, low voltage stress across the power switches, medium voltage gain and high efficiency.

Enhanced quadratic DC–DC boost converters with super‐wide voltage gain ranges and ultra‐low voltage stress for renewable energy systems

AbstractAs the promising and ideal clean energies, wind and solar energy systems are in desperate need of high‐performance DC–DC converters to realize efficient and reliable energy transformation. Conventional DC–DC converters for renewable energy systems will work at extreme duty cycles and affect the system efficiency and reliability owing to their limited voltage gains and high‐voltage stress. In this paper, by adopting the hybrid voltage multiplier cells, two enhanced quadratic boost converters (EQBCs) which are highly desirable for renewable energy applications are proposed and analyzed. The EQBCs possess super‐wide voltage gain ranges and ultra‐low voltage stress; therefore, small duty cycle conditions can be achieved and components with low‐rated voltages can be chosen to decrease system volumes and increase system efficiencies. Besides, the EQBCs possess continuous input currents, which can realize small input current ripples and avoid the serious effect of pulsating current on the input sources. What's more, stable output voltages and simple controller circuits are realized by the EQBCs because of the common grounded structures of the input terminal, the single active switch and the output terminal. Detailed principle analyses, parameter designs, performance comparisons and experimental prototypes are conducted to verify the characteristics and feasibilities of the EQBCs.

Contribution to the Development of a Smart Ultrasound Scanner: Design and Analysis of the High-Voltage Power Supply of the Transmitter

A smart ultrasound scanner plays an important role in the transition to point-of-care imaging. DC–DC bipolar converters are essential in the generation of the ultrasound burst signal as they power the piezoelectric transducer. The conventional bipolar converter has minimal output gain and high-voltage stress, and the longer duty cycle on the semiconductors produces high conduction losses and reduces the efficiency of the system. The transmitter supply voltage is minimal, necessitating the use of high-gain bipolar converters. This proposed study is concerned with the development of an improved high-output voltage gain symmetric bipolar DC–DC converter topology which may be suitable for applications such as powering a smart ultrasound scanner transmitter. The proposed converter combines the conventional single-ended primary inductor converter (SEPIC) with a voltage multiplier cell (VMC) to improve voltage gain, transistor duty cycle, efficiency, and reliability. The present study describes the working principle of the proposed converter. The analysis of the voltage gain is carried out in continuous current mode (CCM) and discontinuous current mode (DCM), taking into account the nonidealities of the device. The simulation of the proposed system is carried out in the numerical environment Matlab/Simulink in order to verify its characteristics. A prototype model is realized and the experimental study presented validates the theoretical arguments and simulations. Due to the advantages of continuous input current, self-balancing bipolar outputs, and small component size, the proposed converter is a suitable choice for smart ultrasound transmitters.