Volar Distal Radius Plate Research Articles

Intraoperative evaluation of dorsal screw prominence after polyaxial volar plate fixation of distal radius fractures utilizing the Hoya view: a cadaveric study.

The irregular nature of the dorsal surface of the distal radius makes it difficult to detect prominent screws with volar plate fixation for distal radius fractures using standard fluoroscopic images. This study evaluates the accuracy of a new radiographic method, the Hoya view, for the assessment of dorsal cortical screw penetration with volar plate fixation. Eight cadaveric upper extremities underwent application of a volar distal radius plate with polyaxial locking screws placed distally. Utilizing a mini C-arm, lateral and Hoya views were obtained with notation of any dorsal cortical screw prominence. Dissection of the cadavers was then performed for direct visualization of screw prominence. The screws were then exchanged sequentially for screws 2-mm longer than their initial measurements with repeated imaging and direct visualization. The Hoya view revealed that 9.4% of the screws penetrated the dorsal cortex with an average screw prominence of 1.08mm (range 0.5-2mm). None of the six prominent screws were detected with lateral views. With the Hoya view, six of six prominent screws were identified. With locking screws exchanged for screws 2-mm longer, 76.6% of the screws had violated the dorsal cortex; of these, 24.5% were detected with lateral imaging versus 100% with the Hoya view. This study supports the intraoperative use of the Hoya view to evaluate screw length and dorsal cortical screw penetration in volar plate fixation of distal radius fractures. However, this view may be difficult to obtain in patients with limitations in elbow or shoulder range of motion.

Distal radius fixation through a mini-invasive approach of 15 mm. Part 1: feasibility study

The aim of this study was to determine the feasibility of a mini-approach for distal radius volar plating. A 15-mm incision was made in 11 cadaver wrists. A 41 mm length and 24 mm width plate was placed deep to the pronator quadratus then fixed using 2 K-wires. The 2 central epiphyseal screws were placed before pin removal, the lateral screws followed and finally the proximal ones. The number of control views needed was on average 1.9 mm, and the position of the plate was good in 10 cases and average in 1 case. The size of the incision after the operation was on average 16.3 mm. No complications were found. Our results show that volar plate fixation of distal radius fracture is feasible through a 15 mm approach. This approach is esthetic, respects noble structures and facilitates reduction due to ligamentotaxis.

Prospective Evaluation of Pronator Quadratus Repair Following Volar Plate Fixation of Distal Radius Fractures

To evaluate the efficacy of pronator quadratus (PQ) repair after volar plating of distal radius fractures. All consecutive distal radius fractures treated operatively with a volar plate during a 1-year period were assigned to receive a repair of the PQ versus no repair. Surgical exposure, reduction, and postoperative rehabilitation were equivalent in both groups. Clinical outcomes with a minimum follow-up of 12 months were assessed via range of motion; grip strength; Disabilities of the Arm, Shoulder, and Hand (DASH) scores; and visual analog scale (VAS) scores. A total of 60 consecutive distal radius fractures were treated operatively with a locking volar plate. Full follow-up data were available for 33 patients in the PQ repair group and 24 patients in the control group. At 12 months, the mean DASH score was 8 for the repair group and 5 for the control group. Range of motion at the wrist, grip strength, and VAS scores were also not significantly different between groups. In addition, we found no significant differences in any of the parameters at the 2-, 6-, or 12-week intervals, although we observed greater grip strength and wrist flexion in the repair group at 6 weeks. Reoperation was required for 4 patients in the repair group and 1 in the control group. Pronator quadratus repair after volar plating of a distal radius fractures did not significantly improve postoperative range of motion, grip strength, or DASH and VAS scores at 1 year. The rates of reoperation between groups were not significantly different.

Improving Accuracy and Confidence in Distal Radius Volar Plate Screw Placement through Supplemental Radiography: Examining Specialty, Education, and Experience Levels

The purpose of this study was to assess the extent to which a supplemental radiographic view increases accuracy and confidence ratings when determining screw placement in volar plating of distal radius fractures for evaluators of different specialties and experience levels. Thirty-four distal radius fractures treated with volar plate fixation were imaged using standard AP and lateral, and supplemental lateral tilt views. Each case was then evaluated for penetration of distal screw tips into the articular space. Sixty-five physicians then completed a two-phase analysis and survey of these cases. In the first phase, presentation consisted only of AP and lateral views; in the second, the lateral tilt view was added. Participants were asked to determine whether distal screws penetrated the joint and rate their confidence in the determination. Assessments were scored for correctness; changes in accuracy and confidence levels between phases were analyzed using paired t tests. Comparisons between groups were performed by ANOVA. Supplementation increased accuracy and confidence in all position, specialty, and experience groups. Confidence scores were significantly higher following evaluation of three views versus two views. Residents exhibited the greatest improvements in accuracy and confidence. For first-phase (standard view) assessments, accuracy scores were significantly better for attendings with less than 10years post-fellowship experience than those with more. A supplemental view of the distal radius combined with AP and lateral views significantly improves the ability of all evaluators, regardless of specialty or training level, to correctly assess placement of fixation screws. The greatest improvements are seen for resident trainees.

Accuracy of Distal Radius Positioning Using an Anatomical Plate

Over the past decade, several anatomical plates have been introduced to improve the result of open reduction and internal fixation of the distal radius. Using 3-dimensional imaging techniques, the authors studied the accuracy and reproducibility of distal radius positioning using anatomical plates.Distal radius fractures and the correction of these fractures were simulated with plastic bone models of radii. The authors simulated a defect by removing an arbitrary wedge shape from the artificial radii. Two surgeons corrected these fractures by placing 2 anatomical plate types according to the plate manufacturers' instructions. The residual positioning errors of the distal segment in relation to the unaffected radii were determined using 3-dimensional imaging and were compared with naturally occurring bilateral radius differences in healthy individuals. In many cases, positioning does not agree with differences based on bilateral asymmetry in healthy patients.This study indicated the accuracy of anatomical plates. Positioning an anatomical plate may lead to considerable residual errors in individual patients. Volar distal radius plate shapes differ among plate manufacturers. Therefore, one plate may perform better than another in an individual.

The Effects of Pronator Quadratus Repair on Outcomes After Volar Plating of Distal Radius Fractures

The purpose of this study was to evaluate forearm rotation after volar plating of the distal radius fractures with and without pronator quadratus repair. This was an institutional review board-approved retrospective review of prospectively collected data. The study was conducted at an Academic Medical Center. Over a 5-year period, 606 patients with distal radius fractures (OTA classifications 23-A through 23-C) were enrolled in an institutional review board-approved, prospectively collected, distal radius database. One hundred and seventy-five patients underwent open reduction and internal fixation with volar plating. Of these, 112 patients had complete 1-year follow-up (6 weeks, 3, 6, and 12 months) and were included in this study. Volar plating of the distal radius was performed with pronator quadratus repair (group A), versus volar plating without pronator quadratus repair (group B). Surgeries in group A were performed by a fellowship trained hand surgeon utilizing volar plates from Depuy Orthopedics (Warsaw, IN), whereas the surgeries in group B were performed by a fellowship trained orthopedic trauma surgeon utilizing volar plates from Stryker (Mahwah, NJ). Primary outcomes include forearm range of motion. Secondary outcomes include grip strength, pain levels, functional outcomes (DASH scores), radiographs, and complications. Baseline and demographic characteristics of the patients were similar between the 2 groups. There was no difference in mean pronation (P = 0.08) at 1 year. Among secondary analyses, radial deviation was significantly different (P = 0.03); however, pain (P = 0.13) and DASH scores (P = 0.14) were not. The only patient that requested plate removal had the pronator repaired (group A). We conclude that there is no advantage in repairing the pronator quadratus during volar plating of distal radius fractures. Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

Distal radius measurements and efficacy of fixed-angle locking volar plates

For surgical treatment of unstable distal radius fractures, fixed-angled locking volar plate fixation is becoming popular nowadays because of some advantages over other surgical techniques. In this article, we discuss the fitting of fixed-angle locking volar plates to the distal radius in relation to the changes in the distal radial angles. First, we took conventional radiography images of 18 dried radii and later we measured the palmar subchondral angle, dorsal subchondral angle, mid-subchondral angle, and palmar cortical angle using lateral radiography. According to the measurements, the volar subchondral angles (alpha) ranged from 10.2 degrees to 28.1 degrees, the middle subchondral angles ranged from 55.9 degrees to 93.2 degrees, the dorsal subchondral angles ranged from 77 degrees to 109.6 degrees, and the volar cortical angles ranged from 134.5 degrees to 158.4 degrees. Although fixed-angle locking volar plates are accepted as anatomical, our measurements showed that volar cortical angles and the subchondral angles are variable. Therefore, the term "anatomic distal radius volar plate" should be discussed.

Sternal Fixation with Nonspecific Plate

The aim of the present study was to fixate displaced sternum fractures with a nonspecific plate, without a sternotomy procedure. Between May 2010 and December 2011, 15 patients with sternal fractures were included in this study. We performed fixation for 8 of 15 sternal fracture patients. Posteroanterior and lateral chest x-rays and computed tomography were taken for diagnosis of sternal fractures. Our surgical indications were severe pain, dislocationoverlapping of sternal edges, and thoracic wall instability. Locked volar distal radius plates were used for the sternal fixation. After fixation of sternum with plate, the sternum was stable in all 8 patients.There were no complications intra- or postoperatively. Sternal union was observed for all. Pain relief was determined dramatically. Locked volar distal radius plates can be used for displaced sternal fractures.It is an alternative and successful method for sternal fractures.

Carbon fiber reinforced PEEK Optima—A composite material biomechanical properties and wear/debris characteristics of CF-PEEK composites for orthopedic trauma implants

BackgroundThe advantageous properties of carbon fiber reinforced polyetheretherketone (CF-PEEK) composites for use as orthopedic implants include similar modulus to bone and ability to withstand prolonged fatigue strain. MethodsThe CF-PEEK tibial nail, dynamic compression plate, proximal humeral plate and distal radius volar plate were compared biomechanically (by four-point bending, static torsion of the nail, and bending fatigue) and for wear/debris (by amount of the debris generated at the connection between the CF-PEEK plate and titanium alloy screws) to commercially available devices. ResultsFour-point bending stress of the tibial nail and dynamic and distal radius plates yielded characteristics similar to other commercially available devices. The distal volar plate bending structural stiffness of the CF-PEEK distal volar plate was 0.542Nm2 versus 0.376Nm2 for the DePuy's DVR anatomic volar plate. The PHILOS proximal humeral internal locking system stainless steel plate was much stronger (6.48Nm2) than the CF-PEEK proximal humeral plate (1.1Nm2). Tibial nail static torsion testing showed similar properties to other tested nails (Fixion, Zimmer and Synthes). All tested CF-PEEK devices underwent one million fatigue cycles without failure. Wear test showed a lower volume of generated particles in comparison to the common implants in use today. InterpretationThus, these tested implants were similar to commercially used devices and can be recommended for use as implants in orthopedic surgery.

Volar versus dorsal latest-generation variable-angle locking plates for the fixation of AO type 23C 2.1 distal radius fractures: A biomechanical study in cadavers

IntroductionAnatomicaly preformed variable-angle locking plates are technologically mature and appear to be optimal for the fixation of distal radius fractures. However, there is still much argument about whether volar plating is equivalent to dorsal (buttressing) plating, especially in the management of intra-articular extension fractures. This biomechanical study was performed to determine, in a simple intra-articular fracture model, whether dorsal or volar plate constructs would be more stable. Materials and methodsSix pairs of fresh frozen radii were examined with dual-energy absorptiometry (DXA) to determine their bone mineral density (BMD). An AO type 23 C2.1 fracture was created. Volar fixation was with a 2.4mm Variable-Angle LCP Two-Column Volar Distal Radius Plate; dorsal fixation was with two orthogonal 2.4mm Variable-Angle LCP Dorsal Distal Radius Plates (both devices: Synthes, Oberdorf, Switzerland). Biomechanical testing used a proven protocol involving static tests of stiffness, and a cyclic test to obtain range of motion (ROM), maximum deformation, and subsidence data. ResultsNone of the constructs failed during biomechanical testing. The two groups (volar and dorsal plating, respectively) did not differ significantly in terms of initial (pre-cyclic-testing) and final (post-cyclic-testing) stiffness. Equally, there was no significant difference between the subsidence values in the two groups. The post-cyclic-testing ROM was significantly greater in the dorsal-plate group as compared with the volar-plate group. The volar constructs showed a significant decrease in the ROM between pre- and post-cyclic testing. ConclusionBiomechanically, volar plating with a modern variable-angle locking plate is equivalent to dorsal plating with two modern variable-angle locking plates.

Volar long locking compression plate fixation for distal radius fractures with metaphyseal and diaphyseal extension

Comminuted distal radial fractures with metaphyseal and diaphyseal extension are uncommon and remain a challenge to treat. The purpose of this study was to assess the radiographic and functional outcomes of treatment with the volar long locking compression plate (LCP) system for distal radius fractures with metaphyseal and diaphyseal extension. This retrospective study was performed on 22 consecutive patients who were treated with open reduction and internal fixation with the application of a 2.4-mm-extra-long LCP volar distal radius plate. Patients were evaluated based on clinical signs and radiography studies. The average time to fracture union was 16 weeks. The volar tilt was restored to a mean of 10.1°. The radial length and radial inclination were restored to a mean of 12.8 mm and 23.6° at final follow-up, respectively. The mean loss of radial length was -1.0 mm at final follow-up as compared with the contralateral extremity. The average ulnar variance was positive 0.1 mm at final follow-up with a congruent distal radioulnar joint. The degree of collapse after fixation between immediate postoperative and final follow-up visit was -0.1 mm. Using the demerit-point system of the Gartland and Werley rating system, 14 results were rated as excellent, 5 as good and 1 as fair. DASH scores averaged 10.1 points. Based on our experience, the volar long LCP is useful in the management of comminuted fractures of the distal radius, in which there is proximal extension into the diaphysis and can avoid or minimize the complications of external fixation or dorsal bridging distraction plate.

The Effects of Screw Length on Stability of Simulated Osteoporotic Distal Radius Fractures Fixed With Volar Locking Plates

Volar plating for distal radius fractures has caused extensor tendon ruptures resulting from dorsal screw prominence. This study was designed to determine the biomechanical impact of placing unicortical distal locking screws and pegs in an extra-articular fracture model. We applied volar-locking distal radius plates to 30 osteoporotic distal radius models. We divided radiuses into 5 groups based on distal locking fixation: bicortical locked screws, 3 lengths of unicortical locked screws (abutting the dorsal cortex [full length], 75% length, and 50% length to dorsal cortex), and unicortical locked pegs. Distal radius osteotomy simulated a dorsally comminuted, extra-articular fracture. We determined each construct's stiffness under physiologic loads (axial compression, dorsal bending, and volar bending) before and after 1,000 cycles of axial conditioning and before axial loading to failure (2 mm of displacement) and subsequent catastrophic failure. Cyclic conditioning did not alter the constructs' stiffness. Stiffness to volar bending and dorsal bending forces were similar between groups. Final stiffness under axial load was statistically equivalent for all groups: bicortical screws (230 N/mm), full-length unicortical screws (227 N/mm), 75% length unicortical screws (226 N/mm), 50% length unicortical screws (187 N/mm), and unicortical pegs (226 N/mm). Force at 2-mm displacement was significantly less for 50% length unicortical screws (311 N) compared with bicortical screws (460 N), full-length unicortical screws (464 N), 75% length unicortical screws (400 N), and unicortical pegs (356 N). Force to catastrophic fracture was statistically equivalent between groups, but mean values for pegs (749 N) and 50% length unicortical (702 N) screws were 16% to 21% less than means for bicortical (892 N), full-length unicortical (860 N), and 75% length (894 N) unicortical constructs. Locked unicortical distal screws of at least 75% length produce construct stiffness similar to bicortical fixation. Unicortical distal fixation for extra-articular distal radius fractures should be entertained to avoid extensor tendon injury because this technique does not appear to compromise initial fixation. Using unicortical fixation during volar distal radius plating may protect extensor tendons without compromising fixation.

Effect of Distal Radius Volar Plate Position on Contact Pressure Between the Flexor Pollicis Longus Tendon and the Distal Plate Edge

Some clinical studies have suggested that distal radius plates placed distal to the watershed line have the potential to impinge on the traversing flexor tendons. However, the validity of this theory remains unclear. The purpose of this study was to evaluate the quantitative effect of volar plate position on flexor pollicis longus (FPL) tendon friction by measuring the contact pressure between the FPL tendon and the distal edge of the locking plate. We used 7 fresh cadaveric upper extremities without wrist osteoarthritis or any deformity. External loads of 1.5 and 3.0 kgf were applied to the FPL tendon to simulate the pinch function of the thumb. A distal radius volar plate was applied to these cadaveric specimens in various positions relative to the watershed line. We measured contact pressure between the distal plate edge and the FPL tendon using a thin flexible pressure sensor and compared it among various positions of the volar plate for wrist extension angles of 0°, 30°, and 60° and ulnar deviation angles of 0° and 20°. Under the 30° or 60° wrist extension condition, contact pressure significantly increased when the distal plate edge was placed distal to the watershed line, compared with when it was placed proximal to or at the watershed line. Our quantitative results support the theory that plates placed distal to the watershed line have the potential to impinge on the traversing FPL tendon, even when a radius fracture heals anatomically. This study clarifies a mechanism of FPL tendon irritation after volar plate fixation for distal radius fractures.

Removal of Locked Volar Plates After Distal Radius Fractures

We present our experience with removal of locked volar distal radius plates and screws and note the indications for removal, types of plates removed, completeness of hardware removal, and complications occurring during plate removal. We reviewed all distal radial volar locking plates removed at our institution from 2004 to 2009. A total of 28 patients operated on by 5 hand surgeons were identified. We gathered information regarding the incidence of successful removal of hardware and operative findings in cases of difficult removal of hardware. A total of 28 patients (16 women, 12 men) underwent removal of locked volar distal radius plates from 2004 to 2009. The mean length of implantation was 63 weeks (range, 3-223 wk). Reasons for removal of hardware included tenosynovitis, tendon rupture, pain, and prominent or intra-articular hardware. Of 28 cases of locked volar plate removal, 2 had complications. In the first case, a screw was cross-threaded in an earlier generation DVR Hand Innovations plate implanted in 2003. The plate and screw were removed by rotating them out as 1 unit. In the second case, in which the current generation DVR Hand Innovations plate was implanted in 2007, the recess in the screw head had been stripped on insertion. The plate was cut and the remaining fragment of plate and screw were removed together. Despite these difficulties, hardware was successfully removed completely in 28 patients. This case series highlights the result that all removals of locked volar plates were successful. There were 2 complications, and strategies for removal are described. Therapeutic IV.

Rotational Fluoroscopy Assists in Detection of Intra-Articular Screw Penetration During Volar Plating of the Distal Radius

Rotational Fluoroscopy Assists in Detection of Intra-Articular Screw Penetration During Volar Plating of the Distal Radius

Rupture of flexor tendon as the complication of volar distal radius plate

Rupture of flexor tendon as the complication of volar distal radius plate

TFCC Reattachment After Traumatic DRUJ Instability

With current trends favoring open reduction with internal fixation for distal radius fractures, distal radius-ulnar joint instabilities that were once clinically silent as a result of prolonged immobilization are now being recognized as a significant cause of morbidity. Arthroscopic management has proven to be both an effective and technically challenging treatment for triangular fibrocartilage complex (TFCC) tears. TFCC reattachment offers a safe, reproducible means of managing acute posttraumatic distal radioulnar join (DRUJ) instability after distal radius volar plating. With this technique, 30 patients at an average of 43 months were examined for continued DRUJ instability, range of motion, and radiographic evaluation for radius union, posttraumatic DRUJ arthritis, and hardware failure. Postoperative Gartland scores showed 88.6% excellent, 5.7% good, and 5.7% fair results. We conclude TFCC reattachment is a safe and effective alternative for treatment of acute DRUJ instability after open reduction with internal fixation of the distal radius, especially when equipment or experience does not support arthroscopic treatment.

Risk Factors for Complications of Distal Radius Volar Plating: Level 2 Evidence

Risk Factors for Complications of Distal Radius Volar Plating: Level 2 Evidence

Hand Numbness and Carpal Tunnel Syndrome after Volar Plating of Distal Radius Fracture

We report the incidence of late onset post-operative carpal tunnel syndrome (late carpal tunnel syndrome) and late median nerve neuropathy after volar plating of distal radius fracture by conducting a retrospective study on volar plating for distal radius fracture performed during 2002 to 2006. Two hundred eighty-two volar plating were performed for acute distal radius fracture after exclusion. Post-operative hand numbness occurred in 24 patients of which nine had carpal tunnel syndrome. Thus, the incidence of late carpal tunnel syndrome was 3.2% (9/282). Of the eight (8/24, 33%) patients with post-operative hand numbness that failed to respond to conservative treatment, five had carpal tunnel release and three had neurolysis of median nerve at distal forearm. All had clinical improvement except in one patient. The incidence of late carpal tunnel syndrome after volar plating of distal radius in the present series is similar to the prevalence of carpal tunnel syndrome in general population. The incidence is low compared with other series, regardless of treatment method (conservative treatment, volar or dorsal plating). The outcome of post-operative hand numbness is generally favourable.

Functional results and complications of locked distal radius volar plates

Introduction and purpose In the last few years, there has been increased aggressiveness in the treatment of distal radius fractures by means of internal fixation. Locked plates prevent metaphyseal collapse even in the presence of osteoporotic or comminuted bone; they also maintain reduction and allow early motion. Nevertheless, there is as yet not enough evidence as to what may be the best way of treating this fracture. Our purpose is to assess our functional results and the complications that can arise from the use of distal radius locked plates. Materials and methods This is a retrospective study of 145 unstable distal radius fractures treated by means of a locked volar plate, with a mean follow-up of 28 months. AO (Association for the Study of Osteosynthesis) and Fernandez’ classifications were used to assess the presence of osteoporosis, need for a graft, difference between healthy and fractured hand in terms of mobility, the radiographic measurements and the functional PRWE (Patient-Rated Wrist Evaluation) test and any potential complications. A statistical analysis was carried out. Results 95 patients were analyzed. Mean PRWE score was 13 points. A significant relation was found between motion and functional result. A graft was used in 3 patients and there were no cases of pseudoarthrosis or metaphyseal collapses. Eight percent of patients presented with some serious complication (algodystrophy, chronic pain, malunion). Conclusions Locked plates can be regarded as an alternative to the treatment of unstable distal radius fractures. They provide good functional results and few complications, they minimize the need for grafting and they allow early mobilization even in the presence of osteoporotic and comminute bone.