Vertical Extensions Research Articles

Impact of the geological structures on the groundwater potential using geophysical techniques in West Bani Mazar area, El Minia – Western Desert, Egypt

Establishment of the new agricultural projects in west Bani Mazar area, El Minia, Egypt needs a good knowledge about groundwater. Groundwater serves as the unique source of water supplies in the study area. Vertical Electrical Sounding technique is a convenient tool for groundwater exploration. This technique was utilized to illustrate the geoelectric succession, vertical and spatial extensions of the encountered layers, depth to water bearing layers and the structures affecting these layers. Profiling technique was carried out along a grid pattern using different half current electrode spacings (150 m, 300 m and 500 m) to clarify changes in resistivity values throughout the study area at different depths. Geoelectric layers B1 and B2 of the saturated zone are suitable for groundwater extraction in the study area. The resistivity values of the geoelectric layer B1 decrease towards the West direction, they decrease from 23.0 Ωm to 16.0 Ωm; and its thicknesses increase towards the SE direction from 12.0 m to 18.0 m. Whereas, the resistivity values of the geoelectric layer B2 decrease towards the NW direction from 40.0 Ωm to 26.5 Ωm; and its thicknesses vary from 34.0 m to 40.0 m. The depths to the upper surface of the water bearing layer B1 increase towards the NW direction from 44.0 m to 89.4 m. Based on the results obtained from the Vertical Electrical Soundings, four two-dimensional resistivity imaging profiles were measured at the selected sites. These 2-D resistivity profiles aim to determine depths to the water bearing layers, their thicknesses and the shallow structure. The inverted models of these profiles matched with the geoelectric sequence at these sites. In addition, a normal fault is detected at the northwestern part of the study area.According to the results obtained from this study it is clear that the groundwater in the area under consideration is occurred in the fractured limestone layers that belong to Eocene Age. Resistivity values of the water bearing layers increase with depth as a result of decreasing fracture density; and these values decreased towards the northwestern direction due to their proximity from the fault zone. The groundwater potential of these layers depends mainly on the lithologic composition and the geological structures affecting these layers. The secondary porosity of these limestone layers depends mainly on the degree of fracturing and fissuring. The proper sites to drill new productive wells were recommended, and the obtained data from drilling new well in the southeastern part of the study area coincide with the interpreted data of the different geophysical techniques.

Microscale characteristics of homogeneous freezing events in cirrus clouds

AbstractWe investigate homogeneous freezing of aqueous aerosol particles, a fundamental ice formation process in cirrus clouds. We estimate freezing time scales and vertical extensions of freezing layers, demonstrating that such freezing events are highly transient and localized. While time scales decrease with increasing vertical velocity driving ice nucleation, layer depths are weak functions of the vertical velocity. Our results are used to discuss possible effects of turbulent diffusion and entrainment‐mixing on homogeneous freezing in cirrus. Large turbulent diffusivity acts to broaden water vapor‐depleted freezing layers and facilitate sedimentation of freshly nucleated ice crystals out of them into ice‐supersaturated air. Homogeneous freezing events could be affected by microscale turbulence in episodes of intense turbulence dissipation rates, although such episodes are rare. We conjecture that freezing layers are broader in the case of heterogeneous ice nucleation and effects of sedimentation on nucleation increase in importance. Our findings point to the difficulty of inferring nucleated cirrus ice crystal numbers from measurements and place tight constraints on cirrus models with regard to spatial and temporal resolution.

Vertical Extension and Improving of Existing Buildings

Low-density urban models, widely diffused in Spain until 2008, have been strongly criticized because they produce a great strain on the land, high infrastructure costs, increasing maintenance expenses, energy waste and pollution from excessive transport, time wasted commuting and more bedroom communities. To counterbalance this effect, opponents are claiming for a review of the capacity that the conventional city, with its higher population density and mixed uses, may still possess. One possibility that has been explored is the vertical extension of buildings, which capitalizes on the remaining buildable space characteristic of many older buildings, and at the same time, refurbishes the housing block and improves standards of energy efficiency, safety and accessibility. The challenge is not only technical - it is clear what needs to be done and how to do it - but it is also social and fiscal; in other words, how do we get organized and how do we finance such a project? The preferred construction system for vertical extensions is industrialized and uses two main materials: steel and wood. The system involves the use of two-dimensional panels and 3D pods that, once completed in the factory, are transported to the worksite, lifted by a crane and installed on the roof of the building. From refurbishing the existing building to adding the new vertical extension, the entire operation takes four months. The experience of this vision and its application in the area of the Example in Barcelona, coming soon to other central neighborhoods in Spanish cities, allows us to present our first results: the detection of over 2,000 buildings with remaining buildable space, the need to vertically extend 50 buildings and our completed projects, in some cases already inhabited, of which half a dozen are currently undergoing environmental evaluation using our own tool.

Geophysical and hydrogeological investigation to study groundwater occurrences in the Taref Formation, south Mut area – Dakhla Oasis - Egypt

Integrated geophysical and hydrogeological techniques can give vital information about groundwater occurrence in the south Mut area, where groundwater is the sole source of water supply in this arid area. Quantitative interpretation of the Vertical Electric Soundings (VES) clarified the geoelectric succession in the study area. Geoelectric parameters (resistivity and thickness) of each geoelectric layer and the available data of the existing wells were used to illustrate the vertical and spatial extensions of the encountered layers, depth to the water-bearing layer, the structures affecting these layers, water level and groundwater flow of the concerned aquifer.Groundwater in the study area occurs under confined and semi-confined conditions in the northern part and it occurs under unconfined conditions in the southern part. Dar Zarrouk (DZ) parameters were calculated to differentiate the areas of confined conditions from those of unconfined conditions. Groundwater salinity ranges between 343 and 654 ppm which is suitable for all purposes and its type is calcium sulfate and sodium sulfate.Petrophysical analyses were carried out on the collected rock samples to evaluate their mineralogical and pore properties, which showed that this aquifer is composed of arenite sandstone with good porosity.The results of the analysis of three constant pumping tests revealed that the hydraulic conductivity and transmissivity have high values, indicating that the aquifer has high potentiality. Combining the geoelectrical and hydrogeological results, the best sites for drilling new productive wells were recommended.

도서관건축의 리모델링 수법

This study is to analyze the remodeling method of library in terms of space extension method and urban regeneration by repurposing function in unused facilities through case study. In many case of library extension, horizontal extensions are more frequent than vertical extensions, because there are limits to extend vertically due to high live load estimation by book stacks. Extension schemes was organized by new building extension method in connection with existing buildings, attaching method small scaled mass or linear mass to existing building, connecting method a plurality of existing small buildings, vertical extension method on the top of the structure, underground extension method using special structure. Unused facility remodeling to the library, large scaled buildings can be developed completely to the function of the library through the relocation of the space, while small scaled building needs spatial extension. In the case of spatial extension, existing space that was used for other purposes can be used as a reading room or office, avoiding high live load estimation.

Strategije brendiranja u nižem cenovnom segmentu proizvoda - analiza tržišta negaziranih voćnih sokova u Srbiji

Frequent changes in consumers' preferences cause the need for constant adjustment of manufacturers' offer, which all give much importance to building appropriate brand architecture, that organizes company's portfolio. As a reaction to current growing price sensitive market segment, manufacturers have developed fighting brands and downward vertical brand extensions, while private labels are offered by retailers, so to fulfill expectations coming from the market. Different branding strategies used in fruit juice market in Serbia are the subject of this research and both quantitative and qualitative research methods were used. The results show that low - cost brands are present in this category. However, there's no unique branding strategy. Consumers recognize various levels of products' quality, which influence their readiness to pay for it. Also, manufacturers' presence across different price levels doesn't negatively affect their image amongst the consumers and the level of trust given to manufacturers is generally higher compared to products' brands. In fruit juice category, manufacturers' brands dominate private labels, although 'blind' test results show that quality of these two brands' types doesn't necessarily differ.

Numerical simulation of physical and dynamical characteristics associated with the severe thunderstorm on April 5, 2015 at Kushtia and Jhenaidah

The paper deals with the study of the physical and dynamical characteristics of a severe thunderstorm, which had occurred on April 5, 2015, at about 2100 UTC in the southwestern Bangladesh with location around 23.3–23.7N and 89.0–89.4E within the upazilas (sub-districts) of Kumarkhali and Shailkupa under the districts of Kushtia and Jhenaidah, respectively. The thunderstorm was associated with numerous hails of large size. More than 5000 birds which used to live in the bird sanctuary at Shailkupa and 22,011 birds in Chhaglapara Bird Sanctuary of Kumarkhali died as they were hit by the hails. Large hails also damaged crops, houses and forests over the thunderstorm hit areas. The evolution of the thunderstorm is studied by the WRF model, which is initialized using the National Centers for Environmental Prediction Final reanalysis data of 0000 UTC of April 5, 2015. The simulated results provide a basis to study the physical and dynamical characteristics of the thunderstorm, which are generally not identified by the meteorological observations which are too sparse. The model has captured a micro-low over Kumarkhali and its neighborhood, which favored the occurrence of the severe thunderstorm. The model simulated rainfall is about 26 mm near the place of occurrence, which matches well with the area where the reflectivity of hydrometeor is maximum. The convective available potential energy is found to be 1600 J kg−1 at 1730 UTC near the place of occurrence of the thunderstorm; this indicates high atmospheric instability over the thunderstorm location for the formation of the thunderstorm. The vertical velocity, convergence, cloud water mixing ratio and the ice water mixing ratio and their vertical extensions are found to be satisfactory and responsible for the occurrence of large hails associated with the thunderstorm.

Brand expertise and perceived consistency reversals on vertical line extensions: The moderating role of extension direction

Vertical line extensions are a valuable growth strategy for many retail service sectors. Correctly positioning a new vertical line extension in the price/quality spectrum is an important decision that has considerable implications for bottom line profits. This paper examines the moderating role of extension direction on the effect of perceived consistency on vertical extension evaluations. In two studies, we show that a lack of perceived consistency acts as a reminder to consumers that the brand may be stretching beyond its expertise, increasing perceived performance and financial risks for upscale extensions but not for downscale extensions. As a consequence, higher consistency results in higher upscale extension favourability whereas evaluations of downscale extensions are similar regardless of their perceived consistency with the parent brand.

Mooring observations of equatorial currents in the upper 1000 m of the western Pacific Ocean during 2014

AbstractTime‐depth variations of the equatorial currents over the upper 1000 m depth in the western Pacific Ocean were directly measured by acoustic Doppler current profiler moorings at 2°N, 140°E and 4.7°N, 140°E during January–August 2014. Intraseasonal variations of the equatorial currents, with periods of 37–73 days, were observed encompassing the North Equatorial Countercurrent (NECC), northern branch of the South Equatorial Current (SEC), Equatorial Undercurrent (EUC), Equatorial Intermediate Current (EIC), North Intermediate Countercurrent (NICC), and North Equatorial Subsurface Current (NESC). Compared with previous studies based mainly on shipboard synoptic surveys, the 8‐month time series of velocity profiles provided direct evidence for the existence of NESC, captured reversals of the EIC in May and the NESC in June from westward to eastward direction, and revealed larger vertical extensions of the SEC and NESC and greater depths of the EIC and NICC than previously thought. According to a global analysis product of ocean surface current, during January–April 2014, the NECC was located around its southernmost position and with its the weakest intensity over the past 20 years. Some of the anomalous characteristics of these flows may be related to the fickle El Niño of 2014.

Integrated application of geoelectrical techniques for structural investigations: case study of Wadi Marsad Graben, Jordan

An integrated geoelectrical survey has been conducted at the Wadi Marsad area, south of Jordan, to map the dominant structural features associated with the Arabian-African plate movements. The area is known to be tectonically affected by the epeirogenic movements of the Arabian shield which originated several major and minor structural features. Fifty-four vertical electrical soundings (VES) using Schlumberger configuration and nine induced polarization (IP) profiles (both resistivity and metal factor parameters were determined) were carried out in the investigated area. The integrated use of IP and VES surveys has proved to be efficient in mapping the lateral and vertical extensions of a major graben structure existing in the investigated area.

Gold Mineralization at the Agawa Prospect in Yamaguchi Prefecture, Southwestern Japan

AbstractAgawa gold prospect, located in Yamaguchi Prefecture, southwestern Japan, is a small prospect, where placer gold has been explored and mined since the 17th century. We investigated the prospect to clarify the genesis of the deposit based on the geology, hydrothermal alteration, geochronology, and ore mineralogy. The main mineralized zone of the prospect has a horizontal and vertical extensions of 500 m and 100 m, respectively, and a width of less than 100 m. Gold mineralization in the prospect occurs as dissemination and stockwork veinlets in the intensely sericitized rocks at the apical part of the Agawa dioritic porphyry intrusion at 86.5–88.5 Ma.Mineralization is typified by at least three stages – an early stage characterized by the occurrence of pyrrhotite and native gold; a middle stage by chalcopyrite; and a late stage by pyrite–bornite. Mineral assemblage and fluid inclusion microthermometry estimation suggest a trend of decreasing temperatures from 400°C to 160°C at a constant sulfur fugacity. The mineralizing fluids formed by the mixing of a hypogene fluid of possibly magmatic origin with an external lower‐temperature and lower‐salinity fluid. The mixing process decreased the temperature and salinity of the fluid, resulting in the precipitation of sulfides, native gold and Bi–Te alloys and sulfosalts.The magnetite‐series signature of the Agawa porphyry and related molybdenite‐bearing mineralization indicate that the plutonism of the San‐in granitoids belt extends to the westernmost end of the Honshu Island. The compiled geochronology and distribution of the metallic deposits in the southwestern Japan arc show that transition from ilmenite‐series to magnetite‐series plutonism started earlier in the west, and shifted eastwards with time during the period from Late Cretaceous to Paleogene.

Method for designing two levels RNS reverse converters for large dynamic ranges

In the last years, research on Residue Number Systems (RNS) has targeted larger dynamic ranges in order to further explore their inherent parallelism. In this paper, we start from the traditional 3-moduli set {2n,2n−1,2n+1}, with an equivalent 3n-bit dynamic range, and propose horizontal and vertical extensions to scale the dynamic range and enhance the parallelism according to the requirements. Two different methods to design general reverse converters for extended moduli sets to the desired dynamic ranges are introduced. Previous converters require complex weight selection of the inputs or complex final conversion steps. In this work the weight selection of the multiplicative terms associated to the inputs is reduced to additions of 2n-bit length and the final conversion step requires only one comparison. Experimental results suggest that the proposed approaches achieve significant area reductions, up to 61% lower area reductions, in comparison with the state-of-the-art for generic DR purposes. Despite having identical delay metrics as the existing generic state of the art, Area-Delay-Product efficiency metrics improvements up to 2.7times can be achieved. The obtained results also validate the improved scalability of the proposed approaches, allowing for better results with the increase of n and the DR.

SENSITIVITY ANALYSIS OF A CALIPER FORMED ATOMIC FORCE MICROSCOPE CANTILEVER BASED ON A MODIFIED COUPLE STRESS THEORY

ABS TRACT: A relationship based on the modified couple stress theory is developed to investigate the flexural sensitivity of an atomic force microscope (AFM) with assembled cantilever probe (ACP). This ACP comprises a horizontal cantilever, two vertical extensions and two tips located at the free ends of the extensions, which forming a caliper. An approximate solution to the flexural vibration problem is obtained using the Rayleigh–Ritz method. The results show that the sensitivities of AFM ACP obtained by the modified couple stress theory are smaller than those evaluated by the classical beam theory at the lower contact stiffness. The results also indicate that the flexural sensitivities of the proposed ACP are strong size dependant when the thickness of the cantilever is close to the material length scale, especially at lower contact stiffness. Furthermore, the greatest flexural modal sensitivity occurs at a small contact stiffness of the system, in which the ratio of the cantilever thickness to the material length scale and the distance between the vertical extensions are also small. In this situation, the distance between the vertical extensions and the clamped end of the cantilever and also the vertical extensions lengths are large. The results reveal that the sensitivity of the right sidewall tip is higher than that of the left one.

Differences in the force system delivered by different beta-titanium wires in elaborate designs.

Objective: Evaluation of the force system produced by four brands of b-Ti wires bent into an elaborate design. Methods: A total of 40 T-loop springs (TLS) hand-bent from 0.017 x 0.025-in b-Ti were randomly divided into four groups according to wire brand: TMATM(G1), BETA FLEXYTM (G2), BETA III WIRETM (G3) and BETA CNATM (G4). Forces and moments were recorded by a moment transducer, coupled to a digital extensometer indicator adapted to a testing machine, every 0.5 mm of deactivation from 5 mm of the initial activation. The moment-to-force (MF) ratio, the overlapping of the vertical extensions of the TLSs and the load-deflection (LD) ratio were also calculated. To complement the results, the Young's module (YM) of each wire was determined by the slope of the load-deflection graph of a tensile test. The surface chemical composition was also evaluated by an energy dispersive X-ray fluorescence spectrometer. Results: All groups, except for G2, produced similar force levels initially. G3 produced the highest LD rates and G1 and G4 had similar amounts of overlap of the vertical extensions of the TLSs in "neutral position". G1 and G3 delivered the highest levels of moments, and G2 and G3 produced the highest MF ratios. b-Ti wires from G3 produced the highest YM and all groups showed similar composition, except for G2. Conclusion: The four beta-titanium wires analyzed produced different force systems when used in a more elaborate design due to the fact that each wire responds differently to bends.

Longitudinal tooth cracks and fractures: an update and review

The purpose of this updated review is to further discuss the diagnostic and treatment challenges related to tooth cracks and fractures that occur primarily in the vertical plane, that is, the long axis of the crown and/or root. This includes when and how to identify and determine the category and the extent of the fracture, when a coronally reinforcing restoration should be placed, when root canal treatment is needed, and when a tooth or root should be extracted based on the location and extent of the fracture. The term “longitudinal” is used because they usually represent vertical extensions of cracks or fractures over distance and time. These often present problems with diagnosis and treatment, but should be considered as findings and not as a diagnosis per se. They are pathways for bacteria that may induce pulpal and periapical inflammation or disease. Longitudinal fractures are divided into five definitive classifications from generally least to most severe: (i) craze line; (ii) fractured cusp; (iii) cracked tooth; (iv) split tooth; and (v) vertical root fracture. These differ but have frequently been confused or combined in clinical articles, creating misunderstanding and resulting in incorrect diagnosis and inappropriate treatment. These classifications have been devised to provide global definitions that researchers and clinicians can use to eliminate this confusion. This review is subdivided into these five classifications as to incidence, pathogenesis, clinical features, etiologies, diagnosis, treatment, prognosis, and prevention.

Effects of stress relaxation in beta-titanium orthodontic loops: Part II.

To determine which regions of beta-titanium T-loop springs (TLSs) are more affected by the stress relaxation over a 12-week period. Fifty TLS were previously activated by concentrated bends and divided into five groups of 10 each according to their evaluation periods: immediate assessment (G0), 24 hours (G1), 48 hours (G2), 1 week (G3), and 12 weeks (G4). Groups 1 to 4 were mounted into a structure simulating a clinical situation. After the experimental periods, the springs were scanned for measurement of their angles and numbered from 1 to 9. A two-way analysis of variance was used to detect differences among the angles measured and differences caused by time and also to detect interactions between those two factors. Tukey's test was used to find differences among the groups. Time influenced the angulations of the TLSs (P < .001). Tukey post hoc test showed that G0 (84.1°) presented a different profile, whereas G1 (90.2°), G2 (90.7°), and G3 (91.1°) had similar profiles among each other, with G4 (92.6°) showing a mean value different from all other groups. A significant interaction was detected between activation time and angular deformation in the TLSs (P < .01). Stress relaxation was observed in the TLSs. It was greatest within 24 hours and gradually increased up to 12 weeks. Two regions were identified as responsible for the relaxation of the TLSs: one at the bend between the vertical extensions of the springs and the base arch and the other at the preactivation bends made in the base arch.

Parent-protecting advertising in product line extensions: Role of communication strategy, message type and extension type

Product line extension, the introduction of new products under the same brand name in a given product category, is a growing practice of product innovation in many industries. However, when companies launch line extensions, information of the new products positively or negatively affects consumer evaluations of the parent products in the same line, generating the so-called spillover effects. Through two experimental studies, the current research explores how marketers can employ appropriate communication strategies and message types in advertising to induce favourable spillovers or to avoid negative spillovers in product line extensions. Experiment 1 investigates the interaction between communication strategy and line extension type. Results reveal that for vertical high-end extensions and for horizontal line extensions, ads using relational strategy that focuses on the relatedness between products in the line increase consumer valuation of the parent product; for vertical low-end extensions, ads with elaboration strategy that stresses the uniqueness of the extensions avoid negative spillovers on parents. Experiment 2 further examines how message type moderates the spillover effects in elaboration ads. Results show that, compared with numerical messages, literal messages engender smaller valuation decreases on the parents and consequently alleviate undesirable spillover effects for most types of product line extensions.

The role of perceived value in vertical brand extensions of luxury and premium brands

This study examines the role of perceived value in the relationship between brand attitude, perceived fit, extension attitude and consumers’ purchase intention of downscale vertical extensions of luxury and premium brands in two product categories: cars and shoes. Results from 236 individuals with different income levels show that extension attitude is positively related to purchase intention both directly and indirectly, via the perceived value of the extension; the latter is more strongly correlated than extension attitude to consumers’ purchase intention. Brand attitude is also positively associated with perceived value. Overall, perceived value partially mediates the relationships of brand attitude and of extension attitude with purchase intention. The product category affects the strength of some of the relationships in the model, including the role of fit.

SMALL-SCALE STRUCTURING OF ELLERMAN BOMBS AT THE SOLAR LIMB

Ellerman bombs (EBs) have been widely studied in recent years due to their dynamic, explosive nature and apparent links to the underlying photospheric magnetic field implying that they may be formed by magnetic reconnection in the photosphere. Despite a plethora of researches discussing the morphologies of EBs, there has been a limited investigation of how these events appear at the limb, specifically, whether they manifest as vertical extensions away from the disc. In this article, we make use of high-resolution, high-cadence observations of an AR at the solar limb, collected by the CRISP instrument, to identify EBs and infer their physical properties. The upper atmosphere is also probed using the SDO/AIA. We analyse 22 EB events evident within these data, finding that 20 appear to follow a parabolic path away from the solar surface at an average speed of 9 km s^(-1), extending away from their source by 580 km, before retreating back at a similar speed. These results show strong evidence of vertical motions associated with EBs, possibly explaining the dynamical `flaring' (changing in area and intensity) observed in on-disc events. Two in-depth case studies are also presented which highlight the unique dynamical nature of EBs within the lower solar atmosphere. The viewing angle of these observations allows for a direct linkage between these EBs and other small-scale events in the H-alpha line wings, including a potential flux emergence scenario. The findings presented here suggest that EBs could have a wider-reaching influence on the solar atmosphere than previously thought, as we reveal a direct linkage between EBs and an emerging small-scale loop, and other near-by small-scale explosive events. However, as previous research found, these extensions do not appear to impact upon the H-alpha line core, and are not observed by the SDO/AIA EUV filters.

Resonant frequency and sensitivity of a caliper formed with assembled cantilever probes based on the modified strain gradient theory.

The resonant frequency and sensitivity of an atomic force microscope (AFM) with an assembled cantilever probe (ACP) is analyzed utilizing strain gradient theory, and then the governing equation and boundary conditions are derived by a combination of the basic equations of strain gradient theory and Hamilton's principle. The resonant frequency and sensitivity of the proposed AFM microcantilever are then obtained numerically. The proposed ACP includes a horizontal cantilever, two vertical extensions, and two tips located at the free ends of the extensions that form a caliper. As one of the extensions is located between the clamped and free ends of the AFM microcantilever, the cantilever is modeled as two beams. The results of the current model are compared with those evaluated by both modified couple stress and classical beam theories. The difference in results evaluated by the strain gradient theory and those predicted by the couple stress and classical beam theories is significant, especially when the microcantilever thickness is approximately the same as the material length-scale parameters. The results also indicate that at the low values of contact stiffness, scanning in the higher cantilever modes decrease the accuracy of the proposed AFM ACP.