Van Deemter Plots Research Articles

Photopolymerized organo‐silica hybrid monolithic columns: Characterization of their performance in capillary liquid chromatography

Porous hybrid organo-silica monoliths have been prepared inside pretreated 100 μm id UV transparent fused-silica capillaries using simultaneous sol-gel transition and polymerization of 3-(methacryloyloxy)propyl trimethoxysilane in the presence of toluene as a porogen. The sol-gel reaction was catalyzed by hydrochloric acid while various photoinitiators including azobisisobutyronitrile, 2,2-dimethoxy-2-phenylacetophenone, and Irgacure 819 were used for the photopolymerization carried out under irradiation with UV light at a wavelength of 254 or 365 nm. The chromatographic performance of photopolymerized monolithic columns in RP liquid chromatographic mode was assessed with respect to the following metrics: column efficiency, methylene and steric selectivity, effect of silanol groups, van Deemter plot, permeability, and pore size distribution. Columns with an efficiency of up to 77 000 plates/m for benzene has been achieved at a flow velocity of 0.47 mm/s. The performance of photopolymerized hybrid monolithic column was compared to the performance of columns prepared via thermally initiated polymerization.

Enantioselective ultra-high and high performance liquid chromatography: A comparative study of columns based on the Whelk-O1 selector

This paper reports on the thermodynamic and kinetic evaluation of a new ultra-high performance liquid chromatography broad-spectrum Pirkle-type chiral stationary phase (CSP) for enantioselective applications (eUHPLC). The well-known Whelk-O1 selector was covalently immobilized onto 1.7-μm high-surface-area, porous spherical silica particles to produce a totally synthetic, covalently bonded CSP that was packed into 150mm, 100mm, 75mm and 50mm columns, either 4.6 or 3.0mm ID. A 100mm×4.6mm ID column was fully characterized from a kinetic and thermodynamic point of view, using as reference a conventional HPLC Whelk-O1 column, 250mm×4.6mm ID, based on 5-μm porous silica particles. On the eUHPLC column, van Deemter plots generated Hmin values of 3.53μm for 1,3-dinitrobenzene, at an interstitial mobile phase linear velocity (μinter) of 5.07mm/s, and Hmin of 4.26 and 4.17μm for the two enantiomers of acenaphthenol, at μinter of 4.85mm/s and 4.24mm/s, respectively. Resolution of 21 enantiomeric pairs including alcohols, epoxides, sulfoxides, phosphine oxides, benzodiazepines and 2-aryloxyproprionic esters used as herbicides, were obtained with significant advantages in terms of efficiency and analysis time. Speed gain factors were calculated for the different column geometries (150mm, 100mm, 75mm and 50mm, either 4.6 or 3.0mm ID), with respect to the standard HPLC column (250mm×4.6mm ID), and were as high as 13, in the case of the 50-mm-long column, affording sub-minute separations of enantiomers with excellent resolution factors. In particular, trans-stilbene oxide was resolved in only 10s, while a 50mm×3.0mm ID column was used as a compromise between reduced mobile phase consumption (less than 1mL per analysis) and smaller extra-column band-broadening effect. Given the relatively low viscosity in NP mode, and the excellent permeability of these eUHPLC columns, with backpressure values under 600bar for a wide range of flow rates, the use of standard HPLC hardware is possible. In this case, however, a significant loss in resolution is observed, compared to the UHPLC instrumentation, if no modifications are introduced in the HPLC apparatus to reduce extra-column variance. The excellent efficiency and selectivity, conjugated with the very high-throughput and the ultra-fast analysis time, prove the potentials of the eUHPLC Whelk-O1 columns in the development of enantioselective UHPLC methods.

Temperature effects on nano‐LC column packing technology

We investigated the effect of temperature on the packing procedure of nano-LC columns (up to 50 cm) and on their performance. Several slurries of stationary phase were prepared using different solvent mixtures. Their stability was evaluated at several temperatures: 70°C, 50°C, and room temperature. At the higher temperature (70°C) the suspensions resulted to be stable for a longer time. For each slurry, we compared nano-LC columns packed with ultrasounds at 70°C and at room temperature. All the columns were tested with a standard mixture at 70°C, to reduce the solvent viscosity and the backpressure. Main chromatographic parameters such as the asymmetry factor, As, the reduced plate high, h, pattern in a Van Deemter plot, the total porosity, ε(t), and the permeability, k, were calculated and discussed. One of the nano-LC columns was used to separate a mixture of pesticides in a LC-MS system with an electron ionization LC-MS interface (Direct-EI). From our knowledge, this is the first study on the role of temperature in the efficiency of slurry-packing procedure.

Isopropylammonium Formate as a Mobile Phase Modifier for Liquid Chromatography

Isopropylammonium formate (IPAF), a new alkylammonium formate (AAF) room temperature ionic liquid, has been synthesized from isopropylamine and formic acid and characterized as an organic solvent mobile phase replacement for reversed-phase liquid chromatography (LC). Characterization of IPAF solvent properties in water such as pH, conductivity, and viscosity, as well as its synthesis, is described. The LC polarity (P') and the solvent strength (S) parameters are determined to be 6.0 and 2.4, respectively, similar to those same parameters for methanol and acetonitrile. Application of this RTIL is demonstrated as an organic solvent replacement for reversed-phase LC to separate a test mixture of niacinamide, acetophenone and p-nitroaniline. The van Deemter plot profile for several columns of different dimensions, particle size, pore size and stationary phase are compared using an IPAF-water mobile phase. At flow rates above 2 mL/min, on-line mixing of the viscous IPAF with water appears not to be uniform. A flattening of the van Deemter profile is noted for particularly short (50 mm) wide bore (4.6 mm) columns packed with larger particles (10 µm). Small particle longer columns likely facilitated mixing at the beginning of the column generating typical linearly increasing van Deemeter curves. IPAF has been further shown as a function of temperature to be a non-denaturing modifier solvent for the separation of the protein cytochrome c from tryptophan compared to methanol. This is important to show, because the semi-preparative separation of native proteins using AAF mobile phases is the long-term goal of this research program.

Preparation and characterization of neutral poly(ethylene glycol) methacrylate-based monolith for normal phase liquid chromatography

A novel porous poly(ethylene glycol) methacrylate-based monolithic column for normal phase liquid chromatography was prepared by thermally initiated polymerization of poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) and ethylene dimethacrylate (EDMA) in the presence of selected porogens. The monolith was macroscopically homogeneous, had low flow resistance, and did not swell or shrink significantly in solvents of different polarities. Inverse size-exclusion data indicate that the monolith had a total porosity of 79.2%, including an external porosity of 69.3% and an internal porosity of 9.9%. Due to its mild polarity (hydrophilicity), the PEG-functionalized monolith could perform traditional normal phase chromatography using non-polar solvents The van Deemter plot demonstrated that the column efficiency of 33,600–34,320 theoretical plates/m could be achieved at a linear flow velocity of 0.9–1.5mm/s. The dual retention capability (both weak hydrophilic and hydrophobic interactions) investigated in this paper explains well why the PEG-functionalized monolith could operate in various chromatographic modes.

Investigation of neutral monolithic capillary columns with varying n‐alkyl chain lengths in capillary electrochromatography

Two different neutral nonpolar monolithic columns series (designated as A and B columns series) each consisting of three columns at varying n-alkyl chain length were prepared by the copolymerization of the functional monomers C8-methacrylate, C12-acrylate, or C16-methacrylate with the cross-linking monomer pentaerythritol triacrylate (PETA) to yield monoliths with surface bound C8, C12, and C16 chains. In the A columns series, the composition of the functional monomers and crosslinker was adjusted to yield comparable chromatographic retention regardless of the alkyl chain length. In the B columns series, the composition of the functional monomers and crosslinker was kept constant yielding chromatographic retention, which increased as expected in the order of increasing the n-alkyl chain length. Due to their direct influences on the monolith porosity and retention energetic, the nature and composition of the monomers at a given porogen composition have largely affected the solute's mass transfer characteristics and sorption kinetics, as assessed by the van Deemter plots and separation efficiencies. The C16-monolith of the A series yielded the highest separation efficiency toward small solutes, but the A columns series were inadequate for protein separation. The C8-monolith of the B series provided the best separation efficiency for proteins while for tryptic peptide mapping, the C16-monolith of the A series seems to provide the best separation. For large protein molecules, the energetically "softer" C8 surface allowed faster sorption kinetics and in turn improved efficiency, while an energetically "harder" C16 surface favored better separation of the smaller size peptide solutes.

Fused core particles as an alternative to fully porous sub-2 μm particles in pharmaceutical analysis using coupled columns at elevated temperature

The chromatographic performance of columns packed with fused-core particles was compared to that of fully porous particles (sub-2 μm) at elevated temperature and extended column lengths. The study involved a comparison of chromatographic parameters such as retention, selectivity, resolution, efficiency and pressure drop. The analytes showed lower retention on fused core particles compared to sub-2 μm particles at low and high temperatures, with substantially lower backpressure. Van Deemter plots were constructed for both kinds of packing materials using single and coupled columns of different lengths at different temperatures. Lower backpressure across the fused core particles allowed two columns to be coupled at 30 °C to generate ∼66 000 theoretical plates, and three columns could be coupled at 60 °C generating ∼129 000 plates. On the other hand, only two sub-2 μm columns could be coupled at 60 °C generating ∼49 000 plates at the optimum flow rate. Fused-core particles showed similar efficiency to sub-2 μm particles at and below the optimum linear velocity, but with lower backpressure. As an application to pharmaceutical analysis, two mixtures of pharmaceuticals of different classes were separated to illustrate the possibility of using fused-core particles as an alternative to sub-2 μm particles in terms of speed and efficiency. The low back-pressure of the fused-core particles allowed fast separations to be performed without significant loss in efficiency or resolution and allowed column coupling to increase efficiency.

Preparation and chromatographic evaluation of a cysteine-bonded zwitterionic hydrophilic interaction liquid chromatography stationary phase

A cysteine-bonded zwitterionic hydrophilic interaction chromatography (HILIC) stationary phase (Click TE-Cys) was prepared based on the “thiol-ene” click chemistry. The Click TE-Cys material was characterized by solid state 13C cross polarization/magic-angle spinning (CP/MAS) NMR and elemental analysis. The dynamic evaluation for cytosine, cytidine and orotic acid was performed using Van Deemter plots. The plate height values were no more than 24μm for the flow rate between 0.5 and 5.4mms−1 (0.3–3.5mLmin−1), which proved the excellent separation efficiency of Click TE-Cys stationary phase. The influences of the content of water, concentration of salt and pH of the buffer solution on the retention of model compounds were investigated. The results demonstrated that the separation of polar analytes was dominated by the partitioning mechanism, while the contribution of electrostatic interaction was minor. The thermodynamic characteristic of Click TE-Cys stationary phase was also studied according to van’t Hoff plot. An exothermic process for transferring analytes from the mobile phase to the stationary phase was observed and a linear relationship for lnk and 1/T was achieved, indicating no change of retention mechanism within the measured temperature range. Besides, the zwitterionic stationary phase exhibited good stability. Considering the high hydrophilicity of Click TE-Cys stationary phase, the application in the separation of protein tryptic digests was carried out using hydrophilic interaction chromatography–electrospray ionization mass spectrometry (HILIC–ESI-MS). More peaks were adequately resolved on the Click TE-Cys column comparing with that on the TSK Amide-80 column. In addition, the orthogonality between HILIC and RPLC system was investigated utilizing geometric approach. The XTerra MS C18 and Click TE-Cys column displayed great difference in separation selectivity, with the orthogonality reaching 88.0%. On the other hand, the orthogonality between Click TE-Cys and TSK Amide-80 system was 21.4%, i.e. the selectivity was similar but slightly different from each other. The successful separation of protein digests indicated the great potential of Click TE-Cys stationary phase in the separation of complex samples and applicability in two-dimensional liquid chromatography (2D-LC).

Pellicular Particles with Spherical Carbon Cores and Porous Nanodiamond/Polymer Shells for Reversed-Phase HPLC

A new stationary phase for reversed-phase high performance liquid chromatography (RP HPLC) was created by coating spherical 3 μm carbon core particles in a layer-by-layer (LbL) fashion with poly(allylamine) (PAAm) and nanodiamond. Unfunctionalized core carbon particles were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and Raman spectroscopy. After LbL of PAAm and nanodiamond, which yields ca. 4 μm core-shell particles, the particles were simultaneously functionalized and cross-linked using a mixture of 1,2-epoxyoctadecane and 1,2,7,8-diepoxyoctane to obtain a mechanically stable C(18)/C(8) bonded outer layer. Core-shell particles were characterized by SEM, and their surface area, pore diameter, and volume were determined using the Brunauer-Emmett-Teller (BET) method. Short stainless steel columns (30 × 4.6 mm i.d.) were packed and the corresponding van Deemter plots obtained. The Supporting Information contains a MATLAB program used to fit the van Deemter data. The retentions of a suite of analytes were investigated on a conventional HPLC at various organic solvent compositions, pH values of mobile phases, including extreme pH values, and column temperatures. At 60 °C, a chromatogram of 2,6-diisopropylphenol showed 71,500 plates/m (N/m). Chromatograms obtained under acidic conditions (pH 2.7) of a mixture of acetaminophen, diazepam, and 2,6-diisopropylphenol and a mixture of phenol, 4-methylphenol, 2-chlorophenol, 4-chlorophenol, 4-bromophenol, and 1-tert-butyl-4-methylphenol are presented. Retention of amitriptyline, cholesterol, and diazinon at temperatures ranging from 35 to 80 °C and at pH 11.3 is reported. A series of five basic drugs was also separated at this pH. The stationary phase exhibits considerable hydrolytic stability at high pH (11.3) and even pH 13 over extended periods of time. An analysis run on a UHPLC with a "sandwich" injection appeared to reduce extra column band broadening and gave best efficiencies of 110,000-120,000 N/m.

High-Efficiency Liquid Chromatography Using Sub-2 μm Columns at Elevated Temperature for the Analysis of Sulfonamides in Wastewater

Efficiency in HPLC can be enhanced by increasing the column length and/or decreasing the particle size. The use of high temperature in HPLC has emerged as a valuable tool to overcome the increase in column backpressure when using small packing particles, as it allows for reduction in mobile phase viscosity. In this study, high plate count was obtained by coupling sub-2 μm columns at elevated temperature to reduce the viscosity of the mobile phase, thus reducing the column backpressure. At 80 °C, up to three columns of 15 cm × 4.6 mm I.D. packed with 1.8 μm particles could be coupled generating ~84,000 theoretical plates for the last eluting compound. The number of theoretical plates was increased on average by a factor of ~3.6 when three columns were coupled at 80 °C compared with one column at 30 °C. The relationships between separation efficiency and column length were examined using Van Deemter plots constructed at 30 °C and 80 °C for different column lengths. The advantages of using coupled columns in combination with elevated temperature for the environmental analysis were illustrated using test mixtures comprised of eight sulfonamides separated on one column at 30 °C and three coupled columns at 80 °C by isocratic elution. Sample clean up was carried out by employing solid-phase extraction (SPE) using Oasis HLB cartridges. The method developed was validated based on parameters such as linearity, precision, accuracy, detection and quantification limits. Recoveries generally ranged from 71.7 to 99% (with the exception of sulfanilamide), with standard deviations not higher than 4.7%. The detection limits of the method ranged from 0.6–2 μg L−1, while limits of quantification were in the range 2–6.7 μg L−1 with UV detection.

Preparation and Characterization of a Polymeric Monolithic Column for Use in High-Performance Liquid Chromatography (HPLC)

The high-performance liquid chromatography (HPLC) experiment, most often done in the undergraduate analytical instrumentation laboratory course, generally illustrates reversed-phase chromatography using a commercial C18 silica column. To avoid the expense of periodic column replacement and introduce a choice of columns with different stationary phases, we have developed an experiment in which students prepare and test a polymer-based monolithic column. The 10 or 15 cm monolithic column is prepared using 1/8 in. o.d. × 2.3 mm i.d. poly(ether ether ketone) or PEEK tubing. The reaction is accomplished thermally at 60 °C for several hours by polymerization of butyl methacrylate cross-linked with ethylene glycol dimethacrylate in a porogen system consisting of 1,4-butanediol, 1-propanol, and water. Using toluene and naphthalene as analytes, profiles of retention factor as a function of methanol have been shown. A study of essential nutrients can be accomplished by using an ion-pairing reagent to separate thiamine from riboflavin. In addition, plate count and van Deemter plots can be done to determine column efficiency. The experiment can be designed to be completed over a 1 to 3 week period of time. Exposure to polymer chemistry, often not a part of the undergraduate laboratory curriculum, is an additional important aspect of this experiment.

Impact of a pressure drop on a monolithic capillary column on the efficiency and separation ability of the column

The impact of inlet and outlet column pressures on column separation properties was investigated for monolithic capillary column in gas chromatography. It was demonstrated that the classical Van Deemter equation does not allow us to make a clear choice of the optimal separation conditions. More relevant data can be obtained from the dependence of the height equivalent to a theoretical plate (HETP) on the inlet and outlet column pressures. The dependence ensures that the minimum HETP value can be achieved at high values of inlet and outlet column pressures, but the ratio of the pressures must approach 1. The efficiency of the column under these optimal conditions can exceed by 25–35% the column efficiency under the optimal conditions found using the classical Van Deemter plot. It was shown that a decrease in inlet and outlet column pressures even at a relative pressure close to 1 leads to an increase in HETP and the loss of column separation ability.

Plate Heights below 50 nm for Protein Electrochromatography Using Silica Colloidal Crystals

Silica colloidal crystals formed from 330 nm nonporous silica spheres inside of 75 μm i.d. fused silica capillaries were evaluated for the efficiency of capillary electrochromatography of proteins. Three proteins, ribonuclease A, cytochrome C, and lysozyme, each covalently labeled with fluorophor, were well separated over a distance of 1 cm by isocratic electromigration, using 40:60 acetonitrile/water with 0.1% formic acid. A van Deemter plot showed that the plate height for lysozyme, which was the purest of the three proteins, was diffusion-limited for electric fields ranging from 400 to 1400 V/cm. The plate height for lysozyme was below 50 nm at almost all of the migration velocities, and it approached 10 nm at the highest velocity. Eddy diffusion was negligible. Lysozyme migrated over a 12 mm separation length with more than 10(6) plates in 1.5 min. These results indicate that silica colloidal crystals are well suited for electrically driven separations of large, highly charged analytes such as proteins. The 10(6) plates observed for a separation length of barely more than a centimeter means they are potentially valuable for miniaturized separations in microchip and lab-on-a-chip devices.

Optimization of performance of monolithic capillary column in gas chromatographic separations

Dependence of monolithic column efficiency on column pressure was analyzed using modified Van Deemter relationship with incorporated inlet and outlet column pressures as independent variables. It was demonstrated that the highest column efficiency is observed at high pressures. Inlet and outlet pressure increase has to be controlled in such a way that the relative pressure approaches 1 and the pressure drop across the column is close to zero. Experimental results obtained for open and monolithic capillary columns confirm up to 50% higher column efficiency as compared to column efficiency under standard conditions found using conventional Van Deemter plot. Pressure increase also results in a decrease in the optimal carrier gas velocity and corresponding increase in the analysis time. This drawback can be compensated via an increase in the column temperature.

Aliphatic carboxylic acids and alcohols as efficiency and elution strength enhancers in micellar liquid chromatography

Micellar liquid chromatography (MLC) uses surfactant solutions as mobile phases with added organic additives to enhance both the elution strength and the chromatographic efficiency. Two aliphatic carboxylic acids (1-butanoic and 1-pentanoic) were used as MLC additives and compared with the two corresponding alcohols (1-butanol, 1-pentanol) in terms of elution strength, efficiency and selectivity. A set of 11 phenol derivatives was used as probe compounds. All micellar mobile phases were prepared with sodium dodecylsulfate (SDS) with concentration ranging from 0.05 to 0.15 M and the modifier content within 1.0 and 5.0% (v/v). The elution strength of different mobile phases containing a constant amount of SDS and different amounts of modifiers; and mobile phases containing a constant amount of modifier and different SDS concentration were determined and discussed. The effect of the acid modifiers on efficiency was studied constructing van Deemter plots that showed no minimum within the 0.01–0.7 mL/min flow rate range studied. Temperature effects were also studied constructing the classical van’t Hoff plots. The slight curvature of the plots in the 25–70 °C range may indicate some modification of the surfactant-bonded moiety layer on the stationary phase surface. Since no definitive advantage of the use of aliphatic acids were established compared to their alcohol counterpart, their terrible smell will probably preclude their use as MLC organic modifiers.

POLY(GLYCIDYL METHACRYLATE-DIVINYLBENZENE) MONOLITHIC CAPILLARY AS A STATIONARY PHASE FOR THE REVERSED-PHASE CHROMATOGRAPHIC SEPARATION OF PROTEINS

Capillary column with monolithic stationary phase was prepared from silanized fused-silica capillary of 200 µm I.D. by in situ free radical polymerization of divinylbenzene with glycidy methacrylate in the presence of decanol and tetrahydrofuran as porogens. The hydrodynamic and chromatographic properties of this monolith, such as backpressure at different flow-rate, pore size distribution, van Deemter plot and the effect of varying gradient-rate were investigated. Poly(glycidyl methacrylate-divinylbenzene) monolithic capillary has been used successfully for the reversed-phase chromatographic separation of proteins. Keywords: monolithic stationary phase, poly(glycidyl methacrylate-divinylbenzene), proteins

Characterization of Convection for Molecularly Imprinted Monolith

Convection of molecularly imprinted polymers monolith in LC mode was discussed in this paper. On the MIPs monolith reported here, a flat van Deemter plot of height equivalent to a theoretical plate (HETP) versus superficial velocity was observed. This typical behavior, similar to perfusion packings, suggests that the unique pore structure of the MIPs monolith allowed convection-enhanced mass transfer. Column parameters, e.g., external porosities, internal porosity, column permeability and equivalent sphere dimension, were obtained. Intraparticle Peclet number (λ) was used to characterize the convection in the monolith. In addition, a ratio of the numbers of transfer units, T, for diffusion in the micropores and through-pores has been introduced to quantify the relative importance of the contribution from convection and diffusion to mass transfer. The results show that the flow in a MIP monolith is extremely sensitive to pore size distribution and can be tuned by polymerization parameters.

Study of the selectivity, retention mechanisms and performance of alternative silica-based stationary phases for separation of ionised solutes in hydrophilic interaction chromatography

The separation of a mixture of neutral, strongly acidic and strongly basic compounds was studied in hydrophilic interaction chromatography using a bare silica phase, and bonded silica phases with diol, zwitterionic, amide and hydrophilic/hydrophobic groups. The mobile phase was acetonitrile-ammonium formate buffer at low pH. Differences in selectivity between these various columns indicate that the stationary phase cannot function merely as an inert support for a water layer into which the solutes partition from the bulk mobile phase. Attempts to fit the retention data to equations which describe either partition or adsorption mechanisms were inconclusive. Ion exchange was a significant contributor to the retention of ionised bases on all columns studied. Van Deemter plots indicated that the efficiency as a function of flow rate varied between the columns, which might be attributable in part to the presence of either monomeric or polymeric bonded phase layers.

Photo‐polymerized lauryl methacrylate monolithic columns for CEC using lauroyl peroxide as initiator

Lauryl methacrylate (LMA)-ester based monolithic columns photo-polymerized using lauroyl peroxide (LPO) as initiator were prepared, and their morphological and CEC properties were studied. The composition of the polymerization mixture (i.e. ratios of monomers/porogenic solvents, 1,4-butanediol/1-propanol and LMA/crosslinker) was optimized. The morphological and chromatographic properties of LMA columns were evaluated by means of SEM pictures and van Deemter plots of PAHs, respectively. The polymerization mixture selected as optimal provided a fast separation of a mixture of PAHs with excellent efficiencies (minimum plate heights of 8.9-11.1 microm). Satisfactory column-to-column (RSD<4.5%) and batch-to-batch reproducibilities (RSD<6.3%) were achieved. The LMA columns photo-polymerized with LPO were compared with those prepared with AIBN. Using PAHs, alkylbenzenes and basic compounds for testing, the columns obtained with LPO gave the best compromise between efficiency, resolution and analysis time.

Comparison on photo-initiators for the preparation of methacrylate monolithic columns for capillary electrochromatography

The synthesis of lauryl methacrylate monoliths for capillary electrochromatography by UV polymerization using several free-radical initiators (α,α′-azobisisobutyronitrile, 2,2-dimethoxy-2-phenylacetophenone, dibenzoyl peroxide (BPO) and lauroyl peroxide (LPO)) has been investigated. Using a 1,4-butanediol/1-propanol mixture as porogenic solvent, the influence of each initiator and its content on the morphological and electrochromatographical properties of beds was evaluated. Under their respective optimum content, satisfactory separations of a test mixture of PAHs with similar efficiencies (minimum plate heights of 8.0–12.7 μm obtained from Van Deemter plots) were achieved for the four investigated photo-initiators. The columns photo-polymerized with LPO provided the best compromise between chromatographic performance and analysis time. Moreover, this initiator showed a fine control in the column retention properties. The resulting monolithic columns exhibited a good run-to-run repeatability in the tested chromatographic parameters (RSD < 2.4%) for all initiators investigated; and satisfactory column-to-column repeatability (RSD < 6.0%), except for beds photo-polymerized with BPO (RSD < 10.8%).