Valve Size Research Articles

One-year initial efficacy and safety outcomes of the premounted dry-pericardium Vienna self-expandable transcatheter aortic valve system: A first-in-human VIVA feasibility study.

The dry-pericardium Vienna transcatheter aortic valve system is repositionable and retrievable, already premounted on the delivery system, eliminating the need for assembly and crimping of the device before valve implantation. The VIVA first-in-human feasibility study, a prospective, nonrandomized, single-center trial, evaluated the Vienna aortic valve in 10 patients with severe symptomatic aortic stenosis, who were at intermediate or high surgical risk. This study, registered at ClinicalTrials.gov (NCT04861805), focused on the safety, feasibility, clinical and hemodynamic performance of the Vienna system up to 1-year follow-up. The mean patient age was 79 ± 5 years, 60% male. Valve sizes used: 26 mm (10%), 29 mm (30%), 31 mm (60%). Key hemodynamic improvements were significant: mean aortic valve pressure gradient (mmHg) decreased from 48.7 to 8.1, aortic valve area (cm2) increased from 0.75 to 1.91, and maximum jet velocity through the aortic valve (m/s) decreased from 4.41 to 1.95 (p < 0.0001). No moderate/severe paravalvular leakage was observed, and computed tomography scans revealed no evidence of hypo-attenuated leaflet thickening. The study recorded one life-threatening bleeding event, two cases requiring postprocedural pacemaker implantation, and three ischemic events, with only one causing lasting neurological impairment. Importantly, there were no cases of cardiovascular mortality and only one noncardiovascular death, which was confirmed as unrelated to the device. The study indicates the Vienna valve as a potential option for severe symptomatic aortic stenosis, designed to streamline the procedure and potentially lower healthcare costs by reducing resource and equipment needs, also procedural errors. Further research is essential to thoroughly evaluate its safety and efficacy.

Outcomes of Pledgeted versus Nonpledgeted Suture Technique for Isolated Aortic Valve Replacement

Objective: To compare outcomes of pledgeted versus nonplegdeted suture techniques for aortic valve replacement (AVR). Methods: This was a retrospective study utilizing an institutional database of AVRs performed at our center between 2010 and 2020. All patients who underwent isolated surgical AVR were included, while those who underwent concomitant procedures were excluded. Patients were dichotomized into those who underwent pledgeted vs. nonpledgeted AVR, and 1:1 propensity score matching (PSM) was employed. Clinical and echocardiographic outcomes were compared. Kaplan-Meier survival estimation and Cox regression were performed. Cumulative incidence functions were generated for all-cause readmissions and for heart-failure readmissions. Freedom from major adverse cardiac and cerebrovascular events (MACCE) were also analyzed and compared using Kaplan-Meier methods. Results: A total of 2240 patients were identified. PSM yielded 892 matched pairs. Mean gradient was significantly higher in the pledgeted group (p &lt; 0.001), but patients in this group had a smaller median valve size implanted. There were no significant differences in paravalvular leak rates. Kaplan-Meier survival estimates, cumulative incidence of readmissions, and freedom from MACCE were not significantly different between groups. Conclusion: Long-term survival, readmission rates, and freedom from MACCE are comparable after pledgeted and nonpledgeted AVR. There were no differences in paravalvular leak rates between the two techniques.

Continuous or interrupted pledgeted suture technique in stented bioprosthetic aortic valve replacement: a comparison of in-hospital outcomes

BackgroundThere is ambiguity in the literature regarding the continuous suture technique (CST) for aortic valve replacement (AVR). At our center, there has been a gradual shift towards CST over the interrupted pledgeted technique (IPT). This study aims at comparing outcomes for both techniques.MethodsWe performed a retrospective analysis of a single-center study of patients undergoing AVR between January 2011 and July 2020. Patients were divided into two groups: Continuous suture technique and interrupted pledget-reinforced sutures. The pre-operative and In-hospital clinical characteristics and echocardiographic hemodynamics (i.e. transvalvular gradients and paravalvular leakage) were compared between CST and IPT.ResultsWe compared 791 patients with CST to 568 patients with IPT (median age: 73 and 74 years, respectively, p = 0.02). In CST there were 35% concomitant procedure vs. 31% in IPT (p = 0.16). Early mortality was 3.2% in CST versus 4.8% in IPT (p = 0.15), and a second cross-clamp due to a paravalvular-leak in 0.5% vs. 1.2%, respectively (p = 0.22). The CST was not associated with new-onset conduction-blocks mandating pacemaker implants(OR 1.07, 95% CI 0.54–2.14; P = 0.85). The postoperative gradients on echocardiography were lower in CST compared to IPT, especially in smaller annuli (peak gradients: 15.7mmHg vs. 20.5mmHg, in valve size < 23 mm, p < 0.001).ConclusionsThe continuous suture technique was associated with lower postoperative gradients and shorter cross-clamp time compared to interrupted pledgeted technique. Differences in paravalvular leaks were non-significant, although slightly less in the continuous suture technique. There were no further differences in valve-related complications. Hence, continues suture technique is safe, with better hemodynamics compared to the interrupted pledgeted technique. This may be of clinical importance, especially in smaller size annular size.

Outcomes and treatment strategy of transcatheter aortic valve replacement with balloon-expandable valve in borderline-size annulus

BackgroundCandidates for transcatheter aortic valve replacement (TAVR) occasionally have a “borderline-size” aortic annulus between 2 transcatheter heart valve sizes, based on the manufacturer's sizing chart. Data on TAVR outcomes in such patients are limited. MethodsWe retrospectively reviewed 1816 patients who underwent transfemoral-TAVR with balloon-expandable valve (BEV) at our institution between 2016 and 2020. We divided patients into borderline and non-borderline groups based on computed tomography-derived annular measurements and compared outcomes. Furthermore, we analyzed procedural characteristics and compared outcomes between the smaller- and larger-valve strategies in patients with borderline-size annulus. ResultsDuring a median follow-up of 23.3 months, there was no significant difference between the borderline (n = 310, 17.0 %) and non-borderline (n = 1506) groups in mortality (17.3 % vs. 19.5 %; hazard ratio [HR] = 0.86 [95% CI = 0.62–1.20], p = 0.39), major adverse cardiac/cerebrovascular events (MACCE: death/myocardial infarction/stroke, 21.2 % vs. 21.5 %; HR = 0.97 [0.71–1.32], p = 0.85), paravalvular leak (PVL: mild 21.8 % vs. 20.6 %, p = 0.81; moderate 0 % vs. 1.2 %; p = 0.37), or mean gradient (12.9 ± 5.8 vs. 12.6 ± 5.2 mmHg, p = 0.69) at 1 year. There was no significant difference between the larger-(n = 113) and smaller-valve(n = 197) subgroups in mortality (23.7 % vs. 15.2 %; HR = 1.57 [0.89–2.77], p = 0.12), MACCE (28.1 % vs. 18.4 %; HR = 1.52 [0.91–2.54], p = 0.11), mild PVL (13.3 % vs. 25.9 %; p = 0.12), or mean gradient (12.3 ± 4.5 vs. 13.6 ± 5.3 mmHg, p = 0.16); however, the rate of permanent pacemaker implantation (PPI) was higher in the larger-valve subgroup (15.9 % vs. 2.6 %, p < 0.001). ConclusionBorderline-size annulus is not associated with higher risk of adverse outcomes after BEV-TAVR. However, the larger-valve strategy for borderline-size annulus is associated with higher PPI risk, suggesting a greater risk of injury to the conduction system.

Association of Valve Size and Hemodynamic Performance With Clinical Outcomes in Aortic Valve Replacement - A Long-Term Follow-up in an Asian Population.

Studies of the influence of smaller body type on the severity of prosthesis-patient mismatch (PPM) after small-sized surgical aortic valve replacement (SAVR) are few, but the issue is particularly relevant for Asian patients.Methods and Results: 695 patients who underwent SAVR with bioprosthetic valves had their hemodynamic valve performance analyzed at 3 months, 1 year, 3 years, and 5 years after operation, and clinical outcomes were assessed. The patients were stratified into 3 valve size groups: 19/21, 23, and 25/27 mm. A smaller valve was associated with higher mean pressure gradients at the 4 time points after operation (P trend <0.05). However, the 3 valve size groups demonstrated no significant differences in the risk of clinical events. At none of the time points did patients with projected PPM show increased mean pressure gradients (P>0.05), whereas patients with measured PPM did (P<0.05). Compared with patients with projected PPM, those with measured PPM demonstrated higher rates of infective endocarditis readmission (adjusted hazard ratio [aHR] 3.31, 95% confidence interval [CI] 1.06-10.39) and a higher risk of composite outcomes (aHR 1.45, 95% CI 0.95-2.22, P=0.087). Relative to those receiving larger valves, patients receiving small bioprosthetic valves had poorer hemodynamic performance but did not demonstrate differences in clinical events in long-term follow-up.

Transcatheter aortic valve replacement achieves similar predicted effective orifice area to surgical aortic valve replacement in bicuspid aortic stenosis

BackgroundStudies comparing transcatheter and surgical aortic valve replacement (TAVR and SAVR) for patients with trileaflet aortic stenosis (AS) have found similar or larger effective orifice area (EOA) for TAVR prostheses. To our knowledge, no studies have compared EOA in patients undergoing TAVR versus SAVR for bicuspid AS. MethodsWe retrospectively compared prosthetic valvular sizing and predicted EOA for patients with bicuspid AS undergoing TAVR or SAVR at our institution between January 1, 2016, and December 31, 2021. We excluded patients undergoing procedures for indications other than AS and those without a pre-procedural gated Chest CT. Comparisons included demographics, comorbidities, annular size, prosthetic valve size, predicted EOA and prosthesis-patient mismatch (PPM) for TAVR (N = 78) and SAVR (N = 74) cohorts. ResultsTAVR patients had smaller pre-procedural annular area (501.7 mm2 vs. 571.8 mm2, p < 0.05) and annular perimeter (80.6 mm vs. 86.5 mm, p < 0.05), but larger mean implanted prosthetic valve size (26.4 mm vs 24.2 mm, p < 0.001) compared to SAVR patients. No differences were observed in predicted EOA, predicted EOA indexed to patient body surface area (EOAi), or predicted PPM grade between TAVR and SAVR groups, including in cohorts sorted by pre-procedural annular size. ConclusionsFor bicuspid AS patients undergoing aortic valve replacement, TAVR achieves similar predicted EOA to SAVR. These data support the use of TAVR in selected patients with bicuspid AS and can inform heart team discussions.

О МОРФОЛОГИЧЕСКОЙ ИЗМЕНЧИВОСТИ ДИАТОМОВОЙ ВОДОРОСЛИ KARAYEVIA SUCHLANDTII (BACILLARIOPHYTA)

This scanning electron microscopy study investigates morphological features of the frustule of the diatom algae Karayevia suchlandtii. The study is based on material collected from the Svir River tributaries (Lake Ladoga basin): Ivina, Yanega, Uslanka,Vazhinka, Oyat, Pasha. Quantitative (the valve length and width, the number of striae in 10 µm) and qualitative (the valve shape and the shape of axial areas, the stiae arrangement) characteristics are analyzed. In the surveyed populations of K. suchlandtii, the minimum values of the valve size are smaller than those given in the original description and the literary, that makes it possible to extend the diagnosis of the species.

Real-World Outcomes for the Fifth-Generation Balloon Expandable Transcatheter Heart Valve in the United States

BackgroundThe fifth-generation SAPIEN 3 Ultra Resilia valve (S3UR) incorporates several design changes as compared with its predecessors, the SAPIEN 3 (S3) and SAPIEN 3 Ultra (S3U) valves, including bovine leaflets treated with a novel process intended to reduce structural valve deterioration via calcification, as well as a taller external skirt on the 29-mm valve size to reduce paravalvular leak (PVL). The clinical performance of S3UR compared with S3 and S3U in a large patient population has not been previously reported. ObjectivesThe aim of this study was to compare S3UR to S3/S3U for procedural, in-hospital, and 30-day clinical and echocardiographic outcomes after transcatheter aortic valve replacement (TAVR). MethodsPatients enrolled in the STS/ACC TVT (Society of Thoracic Surgeons/American College of Cardiology Transcatheter Valve Therapy) Registry between January 1, 2021, and June 30, 2023, who underwent TAVR with S3UR or S3U/S3 valve platforms were propensity-matched and evaluated for procedural, in-hospital, and 30-day clinical and echocardiographic outcomes. Results10,314 S3UR patients were propensity matched with 10,314 patients among 150,539 S3U/S3 patients. At 30 days, there were no statistically significant differences in death, stroke, or bleeding, but a numerically higher hospital readmission rate in the S3UR cohort (8.5% vs 7.7%; P = 0.04). At discharge, S3UR patients exhibited significantly lower mean gradients (9.2 ± 4.6 mm Hg vs 12.0 ± 5.7 mm Hg; P < 0.0001) and larger aortic valve area (2.1 ± 0.7 cm2 vs 1.9 ± 0.6 cm2; P < 0.0001) than patients treated with S3/S3U. The 29-mm valve size exhibited significant reduction in mild PVL (5.3% vs 9.4%; P < 0.0001). ConclusionsS3UR TAVR is associated with lower mean gradients and lower rates of PVL than earlier generations of balloon expandable transcatheter heart valve platforms.

Optimal oversizing in transcatheter aortic valve replacement with the self-expanding Evolut valve system.

Valve oversizing has been associated with reduced paravalvular leaks (PVL) and valve migration risk. However, no optimal cut-off oversizing value has been defined for the Evolut system (Medtronic). The aim of this study was to assess the relationship between the degree of oversizing and moderate-to-severe PVL and determine the optimal oversizing cut-off value. We conducted a multicenter study that included 740 consecutive patients with multidetector computed tomography (CT) data. Valve size was selected according to manufacturer recommendations, with oversizing ranging from 10% to 30%. The primary endpoint was moderate-to-severe PVL. The median age was 84 years (79-87 years), with 58.4% women, and a median EuroSCORE II of 4.1% (2.4-7.3%). Moderate-to-severe PVL was observed in 7.0% of the patients. An inverse relationship was found between oversizing and both PVL (11.3%, 8.6%, 5.4%, and 2.7% for quartiles Q1 to Q4; P = .007) and the need for post-dilation (P = .016). The multivariable analysis showed an association between oversizing and PVL (OR: 0.915 for each 1%-increase, P = .002). The optimal oversizing cut-off value to predict PVL was 20%, and PVL was significantly higher in patients with oversizing less than 20% (10.5% vs.4.2%, P less than .001). There were no differences in major clinical events according to the degree of oversizing, and a higher oversizing did not translate into an increased risk of permanent pacemaker (18.4% vs18.3%, P = .976). In TAVR with the Evolut valve, a higher oversizing was associated with lower rates of moderate-to-severe PVL and a lower need for post-dilation, with no negative impact on procedural and early clinical outcomes. A 20% oversizing threshold could be suggested to reduce PVLs. Further prospective studies are warranted to validate optimal oversizing for this valve system.

Association of Relative Left Ventricular Outflow Tract Area and Transcatheter Aortic Valve Replacement Related Paravalvular Leak

BackgroundPost-transcatheter aortic valve replacement (TAVR), paravalvular leak (PVL) is a quality metric associated with worse clinical outcomes. Transcatheter heart valve (THV) sizing is based primarily on the systolic annular size without regard to the left ventricular outflow tract (LVOT), which also lies within the THV landing zone. We hypothesized that LVOT size relative to the annulus is associated with post-TAVR PVL. MethodsData from consecutive patients undergoing TAVR in a single high-volume center from January 2018 to March 2019 were used. Pre-TAVR data from multidetector computed tomography (MDCT) were collected. Relative LVOT area was defined as LVOT area/annular area during systole. Logistic regression analysis was used to evaluate association with post-TAVR mild or greater PVL by transthoracic echocardiography before discharge. ResultsAmong 293 patients (median age, 81.1 years; female, 49.5%; White, 88.0%), 81.6% received SAPIEN 3 and 18.4% received CoreValve THV models. Aortic valve morphology was bicuspid in 10.9% of patients. Prevalence of mild or greater PVL was 23.5% (mild in 20.1%). Relative LVOT area had a significant inverse association such that the odds of mild or greater PVL decreased significantly with every 1% increase in relative LVOT area (adjusted odds ratio, 0.96; 95% CI, 0.93-0.98; P = .002). There was no interaction between the type of implanted valve and the relative LVOT area. Patients in the highest relative LVOT tertile had significantly lower odds of mild or greater PVL (adjusted odds ratio, 0.42; 95% CI, 0.21-0.87; P = .018 vs first tertile). ConclusionsIn patients undergoing TAVR with the newer generation of THV (SAPIEN 3 and CoreValve models), a relatively narrower LVOT area vs annular area was independently associated with increased odds of mild or greater PVL before discharge.

Redo-TAVR Feasibility After SAPIEN 3 Stratified by Implant Depth and Commissural Alignment: A CT Simulation Study.

Redo-transcatheter aortic valve replacement (TAVR) can pin the index transcatheter heart valve leaflets open leading to sinus sequestration and restricting coronary access. The impact of initial implant depth and commissural alignment on redo-TAVR feasibility is unclear. We sought to determine the feasibility of redo-TAVR and coronary access after SAPIEN 3 (S3) TAVR stratified by implant depth and commissural alignment. Consecutive patients with native valve aortic stenosis were evaluated using multidetector computed tomography. S3 TAVR simulations were done at 3 implant depths, sizing per manufacturer recommendation and assuming nominal expansion in all cases. Redo-TAVR was deemed unfeasible based on valve-to-sinotubular junction distance and valve-to-sinus height <2 mm, while the neoskirt plane of the S3 transcatheter heart valve estimated coronary access feasibility. Overall, 1900 patients (mean age, 80.2±8 years; STS-PROM [Society of Thoracic Surgeons Predicted Risk of Operative Mortality], 3.4%) were included. Redo-TAVR feasibility reduced significantly at shallower initial S3 implant depths (2.3% at 80:20 versus 27.5% at 100:0, P<0.001). Larger S3 sizes reduced redo-TAVR feasibility, but only in patients with a 100:0 implant (P<0.001). Commissural alignment would render redo-TAVR feasible in all patients, assuming the utilization of leaflet modification techniques to reduce the neoskirt height. Coronary access following TAV-in-TAV was affected by both index S3 implant depth and size. This study highlights the critical impact of implant depth, commissural alignment, and transcatheter heart valve size in predicting redo-TAVR feasibility. These findings highlight the necessity for individualized preprocedural planning, considering both immediate results and long-term prospects for reintervention as TAVR is increasingly utilized in younger patients with aortic stenosis.

Standardization and validation of neoLVOT assessment using three-dimensional trans-esophageal echocardiography before trans-catheter mitral valve replacement.

Trans-catheter mitral valve replacement (TMVR) procedures had emerged as an alternative solution for patients who are at high risk for mitral valve surgery. Although cardiac computed tomography (CT) remains the standard method for procedural planning, there is no full agreement on the best systolic phase for quantitation of the neoLVOT. Furthermore, a new three-dimensional trans-esophageal echocardiography (3DTEE) based software was developed to serve as filter and or an alternative for patients who cannot have CT due to any contraindication. To determine the systolic phase of the cardiac cycle that shows the narrowest NeoLVOT area in order to standardize the way of using these software and then to validate the 3DTEE-based software against the CT-based one as a gold standard, in mitral valve annulus (MA) and NeoLVOT assessment. A single center, observational, retrospective study. Initially, a sample of 20 patients (age 62±4 years, 70% men) had CT-based analysis at mid-diastole (80%), early-systole (10%), mid-systole (20%), late-systole (30%-40%), in order to detect the best systolic phase at which the neoLVOT area is the narrowest after TMVR. Then, the end systolic phase was standardized for the analysis of 49 patients (age 57±6 years, 60% men), using both the commercially available CT-based software and the newly available 3DTEE-based software (3mensio Structural Heart, Pie Medical Imaging, The Netherlands). The 3DTEE derived parameters were compared with the gold standard CT-based measurements. The neoLVOT area was significantly narrower at end-systole (224±62 mm2), compared to early-systole (299±70 mm2) and mid-systole (261±75 mm2), (p=.005). Excellent correlation was found between 3DTEE and CT measurements for MA AP diameter (r=.96), IC diameter (r=.92), MA area (r=.96), MA perimeter (r=.94) and NeoLVOT area (r=.96), (all p-values<.0001). Virtual valve sizing was based on annulus measurement and was identical between CT and 3DTEE. Interobserver and intraobserver agreements were excellent for all the measurements with ICCs>.80. End-systole is the phase that shows the narrowest neoLVOT and hence should be the standard phase used during the analysis. The 3DTEE based analysis using this new software is reliable compared to the CT-based analysis and can be serve as an alternative analysis tool in patients who cannot have CT for any clinical contraindication or as a screening test and/or filter for all patients before proceeding to a detailed CT scan.

Proposal for computer tomography-based valve sizing and prosthesis simulation in endoscopic aortic valve surgery

Proposal for computer tomography-based valve sizing and prosthesis simulation in endoscopic aortic valve surgery

Research on the influence mechanism of fluid control valve on the production of segmented horizontal wells and the balanced gas production control model: A case analysis of Sichuan basin natural gas

The existing research on the multiple fluid control valves to control the balanced exploitation of natural gas in horizontal wells lacks theoretical model support. On this basis, this paper established a flow rate and pressure model of the segmented horizontal well based on the fluid control valve. The model considers the throttling performance, installation position and opening adjustment step size of the fluid control valve for the first time. Next, systematically analyzed the mechanism of mutual influence of the opening and the position on the flow rate and pressure based on multiple fluid control valves. In addition, a novel method of using the dichotomy model to adjust the production of different production segments was proposed to analyze the horizontal wells of 15 production segments in Sichuan. It was found that when the opening adjustment step size is less than 5%, the natural gas production shows irregular changes, which makes it hard to effectively control the production of each segment. When the step size is 5%, the maximum production variation is 2.7%, which will have a more significant and meaningful effect on the exploitation of natural gas. Through seven iterations, the maximum production errors of high and low production segments are 1.3 % and 1.1 % respectively, both less than 2.7%. The research results verified the correctness of the theoretical model of segmented horizontal wells based on multiple fluid control valves. This research provided a theoretical basis for the opening control of multiple fluid control valves based on different production segments of horizontal wells.

Preprocedural Computed Tomography Planning for Surgical Aortic Valve Replacement

BackgroundSelection of transcatheter valve size using preprocedural computed tomography (CT) is standardized and well established. However, valve sizing for surgical aortic valve replacement (SAVR) is currently performed intraoperatively by using sizers, which may result in variation among operators and risk for prosthesis-patient mismatch. This study evaluated the usefulness of CT annulus measurement for SAVR valve sizing. MethodsThis study included patients who underwent SAVR using Inspiris or Magna Ease and received preoperative electrocardiogram-gated CT imaging. Starting from June 2022, study investigators applied a CT sizing algorithm using CT-derived annulus size to guide minimum SAVR label size. The final decision of valve selection was left to the operating surgeon during SAVR. The study compared the appropriateness of valve selection (comparing implanted size with CT-predicted size) and prosthesis-patient mismatch rates without aortic root enlargement between 2 cohorts: 102 cases since June 2022 (CT sizing cohort) and 180 cases from 2020 to 2021 (conventional sizing cohort). ResultsImplanted size smaller than CT predicted size and severe prosthesis-patient mismatch were significantly lower by CT sizing than by conventional sizing (12% vs 31% [P = .001] and 0% vs 6% [P = .039], respectively). Interoperator variability was a factor associated with implanted size smaller than CT predicted with conventional sizing, whereas it became nonsignificant with CT sizing. ConclusionsApplying CT sizing to SAVR led to improved valve size selection, less prosthesis-patient mismatch, and less interoperator variability. CT sizing for SAVR could also be used to predict prosthesis-patient mismatch before SAVR and identify patients who need aortic root enlargement.

Staged repair of borderline hypoplastic heart disease with early biventricular conversion

ObjectiveIn select patients with borderline ventricular hypoplasia, we adopted a strategy of initial single-ventricle palliation followed by staged or direct biventricular conversion by 2 years of age. MethodsBetween 2018 and 2023, 14 newborns with borderline hypoplastic heart disease deemed high risk for primary biventricular repair underwent palliative procedures as a neonate/infant, followed by staged or direct biventricular conversion. ResultsOf the 14 patients, 6 had borderline left ventricles and 8 had borderline right ventricles. Index neonatal operations were performed in 12 patients and included the Norwood operation (n = 5), pulmonary artery band (n = 3), ductal stent (n = 3), and hybrid Norwood (n = 1). Five patients underwent direct biventricular conversion, and the remaining 9 patients underwent staged ventricular recruitment operations at a mean age of 6 months (range, 3-11 months). Ventricular recruitment operations included atrial septation with or without ventricular rehabilitation, atrioventricular valve repair, or outflow tract operations. At a mean duration of 8 months (range, 4-10 months) after ventricular recruitment, there was a significant increase in chamber volume, aortic valve, and mitral valve size in patients with borderline left ventricles, and a normalization of the right ventricle:left ventricle end-diastolic volume ratio in patients with borderline right ventricles. To date, 13 of 14 patients have undergone successful biventricular conversion at a mean age of 16 months (range, 4-31 months). ConclusionsIn select newborns with borderline hypoplastic heart disease, single-ventricle palliation followed by staged or direct biventricular conversion may increase infant survival while allowing for early attainment of a biventricular circulation.

The archaeology of 19th century oyster consumption in Melbourne

ABSTRACTThis paper presents comparative research on marine shell from four 19th century historical archaeological sites in Melbourne. The shell derives predominantly from Mud Oyster (Ostrea angasi) and Sydney Rock Oyster (Saccostrea glomerata) commercially harvested from natural reefs along the south‐east Australian coastline. The research collects quantitative data that informs on the 19th century oyster industry and investigates inter‐site shell variability and its implications for processing, consumption and discard. Dredging of subtidal reefs provides an explanation for the numerical dominance of oyster, the presence of subfossil cultch (Anadara) and the wide range of minor shellfish. Mud oyster and Sydney rock oyster comparisons in valve size, sided counts and preservation record significant differences within and between sites due to the origins, depositional conditions and the processing of the shell. These data form the basis of two models. The first predicts the archaeological representation of reef dredging and ranks shellfish according to categories, from live oysters to dead shell sampled from the reef substrate. Based on oyster shell anatomy and the separate uses of the right (lid) and left (dish) valves, the second model considers how oyster processing and consumption is characterised archaeologically in differential valve counts and pairing rates.

Transcatheter aortic valve replacement in the treatment of bicuspid aortic stenosis with "down-size" interventional valves: procedural and mid-term follow-up.

Due to the influence of anatomical structure, replacing the bicuspid valve using transcatheter aortic valve replacement (TAVR) would increase the risk of perivalvular leakage and conduction block, affecting the hemodynamic effect of the interventional valve. In this study, for bicuspid and tricuspid valves, we implemented different valve selection strategies to explore the safety and effectiveness of TAVR in the treatment of bicuspid aortic stenosis with "down-size" interventional valves using the VenusA-valve system. The operation was performed with the VenusA-valve via transfemoral approach. The selected valves were appropriately sized based on the results of transthoracic echocardiography (TTE), contrast-enhanced computed tomography (CT), and the morphology of intraoperative pre-dilation balloons. For tricuspid valve cases, the VenusA valve is usually larger than the annulus diameter, whereas the "down-size" approach was adopted for bicuspid aortic valve (BAV) cases. The shape of the pre-dilation balloon allowed further sizing of the annulus diameter by the degree of lumbar constriction of the balloon, aiding in intervention valve size selection, particularly in cases of BAVs. A total of 65 patients underwent TAVR for aortic stenosis with VenusA-valve systems. Of these, 29 cases had a BAV and 36 cases had a tricuspid aortic valve (TAV). The distribution of VenusA-valve sizes differed between TAV and BAV cases (P=0.007). Furthermore, there was a significant decrease in the average mean gradient in TAV patients from 54.7 to 12.2 mmHg (P<0.001), and in BAV patients from 61.6 to 14.3 mmHg (P<0.001). The percentage of paravalvular leakage greater than mild was 6.90% in the BAVs and 5.56% in the TAVs at procedural outcomes (P=0.955). The mean follow-up period was 22.23 months (range, 12 to 39 months). The proportion of New York Heart Association (NYHA) class III/IV decreased from 78.5% preoperatively to 11.3% at the last follow-up (P<0.001). A total of 27 patients with TAV and 19 patients with BAV underwent TTE at 1-year follow-up after operation. There was no significant contrast in the average pressure difference between TAVs and BAVs at 1-year follow-up (11.9 vs. 14.3 mmHg, P=0.18). The VenusA-valve for TAVR produced positive clinical outcomes and valve functionality in both BAVs and TAVs. In the case of BAVs, selecting a smaller interventional valve size was deemed viable.

Left Ventricular Vortex Characteristics in Fetuses With Coarctation of the Aorta by Blood Speckle-Tracking Echocardiography.

The aims of this study were to assess the vortex characteristics of left ventricle (LV) in fetuses with coarctation of the aorta (CoA) using high-frame rate ultrasound with blood speckle-tracking (BST) and explore its relationships with cardiac function and morphology parameters. Thirty fetuses with CoA and 30 gestational-age matched normal fetuses were included in this cross-sectional study. The area, length, width, and position of the vortex in the LV were recorded and quantitatively analyzed by BST echocardiography. The associations of vortex properties with ventricular function and morphology were also determined. Based on BST imaging, the LV vortex can be observed in 93% of the fetuses. The fetuses with CoA exhibited significantly larger and wider vortex than the controls (P < .05). Linear regression analysis indicated that vortex area was positively related to sphericity index of LV as well as isovolumic relaxation time (r = .52, P = .003 and r = .42, P = .021). There was a negative correlation between vortex area and mitral valve size (r = -.443, P = .014). No significant association was found between vortex area and myocardial performance index and aortic isthmus size. It is feasible to quantitatively evaluate the left ventricular vortex in fetuses by BST. The fetuses with CoA exhibited greater vortex area and width, and the altered vortex property is associated with geometry of LV. This will facilitate our comprehension of the unique flow patterns and early cardiac remodeling in fetuses with CoA.

Optimizing percutaneous pulmonary valve implantation with patient-specific 3D-printed pulmonary artery models and hemodynamic assessment.

Percutaneous pulmonary valve implantation (PPVI) has emerged as a less invasive alternative for treating severe pulmonary regurgitation after tetralogy of Fallot (TOF) repair in patients with a native right ventricular outflow tract (RVOT). However, the success of PPVI depends on precise patient-specific valve sizing, the avoidance of oversizing complications, and optimal valve performance. In recent years, innovative adaptations of commercially available cardiovascular mock loops have been used to test conduits in the pulmonary position. These models are instrumental in facilitating accurate pulmonic valve sizing, mitigating the risk of oversizing, and providing insight into the valve performance before implantation. This study explored the utilization of custom-modified mock loops to implant patient-specific 3D-printed pulmonary artery geometries, thereby advancing PPVI planning and execution. Patient-specific 3D-printed pulmonary artery geometries of five patients who underwent PPVI using Pulsta transcatheter heart valve (THV) ® were tested in a modified ViVitro pulse duplicator system®. Various valve sizes were subjected to 10 cycles of testing at different cardiac output levels. The transpulmonary systolic and regurgitation fractions of the valves were also recorded and compared. A total of 39 experiments were conducted using five different patient geometries and several different valve sizes (26, 28, 30, and 32 mm) at 3, 4, and 5 L/min cardiac output at heart rates of 70 beats per minute (bpm) and 60/40 systolic/diastolic ratios. The pressure gradients and regurgitation fractions of the tested valve sizes in the models were found to be similar to the pressure gradients and regurgitation fractions of valves used in real procedures. However, in two patients, different valve sizes showed better hemodynamic values than the actual implanted valves. The use of 3D printing technology, electromagnetic flow meters, and the custom-modified ViVitro pulse duplicator system® in conjunction with patient-specific pulmonary artery models has enabled a comprehensive assessment of percutaneous pulmonic valve implantation performance. This approach allows for accurate valve sizing, minimization of oversizing risks, and valuable insights into hemodynamic behavior before implantation. The data obtained from this experimental setup will contribute to advancing PPVI procedures and offer potential benefits in improving patient outcomes and safety.