Principal Stress Values Research Articles

Study on Bearing Mechanism of Steel Screw Pile

In order to study the bearing mechanism of a steel screw pile (SSP), a 3D-FEM of “SSP-stratum” was established based on the large-scale general finite element analysis platform ABAQUS. Secondly, the real friction coefficient between pile and soil was determined by comparing it with the field bearing test data of screw piles. Finally, the bearing mechanism and failure criterion of the SSP was revealed. The research showed that the pile-soil friction coefficient was about 0.6 under the condition of this stratum, and the screw pile was in the elastic working stage under the conditions of compression and tension load, which had a large bearing reserve. The magnitude of Young’s modulus was inversely correlated with the settlement value and the extreme value of principal stress. The increase in the Young’s modulus of the stratum was helpful in improving the bearing capacity of the screw pile. The compressive capacity of circular steel tube + screw pile (CST + SP) was about 2 times higher than CST, and the compressive capacity of circular steel tube + large blade + screw pile (CST + LB + SP) was about 2.4 times higher than CST. The tensile capacity of CST + SP was about 3.4 times higher than CST, and the tensile capacity of CST + LB + SP was about 4.9 times higher than CST. The arrangement of large blades better bore the load of the screw part and optimized the stress distribution of the structure. Based on the mechanical analysis in the vertical direction, the bearing mechanism of the SSP under compression and tension conditions was elaborated. The bearing failure criterion of the SSP was summarized from the aspects of mechanics and displacement. The bearing design of the SSP should meet the control of mechanics and deformation at the same time. The research work could provide a useful reference for the design and construction of SSPs.

Dynamic response and safety performance of composite-laminated heliostat under hail impact

ABSTRACT Areas rich in solar energy are prone to strong convective weather, leading to severe hail disasters, which makes heliostats under the threaten of hail impacts. An evaluation model of composite laminated heliostat under hail impacting is established and validated. Subsequently, the effect of interlayer type and thickness ratio on the dynamic response and safety assessment of composite laminated heliostats impacted by hail are investigated. Additionally, the velocity thresholds for hail terminal velocity of composite laminated heliostats with a thickness range of 2–4 mm, based on the optimal thickness ratio, are studied. The results indicate that the maximum principal stress value of the composite laminated heliostat remains similar to that of the single-layer heliostat when the interlayer types are SentryGlas Plus (SGP) and Polyvinyl Butyral (PVB). The maximum principal stresses of single-layer heliostats with thicknesses of 2-4 mm are 2.92, 1.50, and 1.35 times, compared to the first-layer glass of composite laminated heliostat with the same thickness under the optimal thickness ratio, which indicates that the hail resistance of the composite laminated heliostat is superior to that of the single-layer heliostat. The findings offer the guidance for the hail resistance of composite laminated heliostat under hail impact.

Effect of different post materials and designs on upper central tooth torque and intrusion load: A finite element analysis study

The aim of this study was to examine the effects of post material type and the presence of ferrules on the torque and intrusion load of the upper central tooth using finite element analysis. The upper central tooth and surrounding tissues (cortical bone, cancellous bone, and periodontal ligament) were modelled in three dimensions using the Spaceclaim software. Five simulated models (SM) different modifications were made to this main model: metal cast post (SM1) and glass fiber post-core with zirconium crown and without a ferrule (SM2), metal cast (SM3) post and glass fiber post with a ferrule and zirconium crown (SM4) and only zirconium crown (SM5). In all five simulations, in order to simulate lingual root torque movement, a total load of 40grams was applied to the bracket slot as 20grams of force couples and in order to simulate intrusion movement, a load of 40grams was applied to the superior wall of the bracket slot. The stress caused by the applied loads on the root surfaces was determined using finite element analysis. Maximum principal stress (MPS) value was used in the comparison. The highest root surface MPS values for both intrusion and torque loads belonged to SM2 (3.864 and 0.379MPa, respectively). The presence of ferrules in both intrusion and torque loads reduced the stress by approximately half (from 3.864 to 2.004MPa). In all five models, the radicular area with higher stress was located in the cervical third on the lingual surface when both torque and intrusion loads were applied. The amount and localization of stress was affected by the type of post material. The variation in stress values between the materials remains within a safe range (0.099 and 3.87MPa), making both materials suitable for use under orthodontic forces.

Evaluation of stress distributions in endodontically treated anterior incisors under occlusal and trauma-induced forces following various restoration treatments: A finite element analysis.

The aim of this study was to calculate the stress distribution of fiberglass post associated with resin composite crown restoration and fiberglass posts with zirconia restorations in mature and immature endodontically treated central maxillary incisor under various loading conditions. The study created six different study models in a virtual environment: healthy mature maxillary central teeth, intact immature maxillary central teeth, mature maxillary central teeth with fiberglass post associated with resin composite crown restoration, immature maxillary central teeth with fiberglass post associated with resin composite crown restoration, mature maxillary central teeth with fiberglass posts and zirconia restoration, and immature maxillary central teeth with fiberglass posts and zirconia restoration. Loading conditions simulating mastication, trauma, and bruxism were applied to each of the models at different angles and amounts. The von Mises and the maximum and minimum principal stress values in tooth structures (dentin) and support structures (bone, PDL) and materials were observed using finite element stress analysis. The highest stress values in the tissue and the restoration structure were observed for masticating force and crowns rehabilitated with zirconia restorations. None of the compared loading conditions and restorations showed destructive stress values on periodontal ligament or bone. The mature and immature endodontically treated central maxillary incisors can be better rehabilitated using fiberglass post associated with resin composite crown restoration and may be preferred to zirconia restorations in order to reduce the stresses on the surrounding tissues and teeth. However, further clinical studies are needed to fully explore this topic.

Effect of different occlusal materials on peri-implant stress distribution with different osseointegration condition: A finite element analysis.

Studies have not been done to evaluate the peri-implant stress exerted by materials(like PEEK and resin matrix ceramics) in different osseointegration conditions. To investigate the effect of different occlusal materials on peri-implant stress distribution with different osseointegration condition using finite element analysis. Eighteen different 3D FEA models of implant fixed with abutment were created involving 6 different occlusal materials (Heat cured temporary acrylic resin (PMMA), Bis-GMA, PEEK, Lithium disilicate, Resin matrix ceramics and translucent Zirconia) and different osseointegrated conditions (50%, 75%, 100%). Models were subjected to loading vertically and obliquely followed by evaluation of stress distribution. The results of the simulation obtained were analysed in terms of Von mises, maximum principal and minimal principal stresses using descriptive stastistics. PMMA (40.14 MPa on vertical loading and 66 MPa on oblique loading) resulted in the highest stresses and lithium disilicate (24 MPa on vertical loading and 52.40 MPa on oblique loading) resulted in least stresses among all the crown materials. Upon oblique loading, von Mises stress increases except for translucent zirconia and lithium disilicate (52.444 MPa on 50%, 47.733 MPa on 75%, and 43.973 MPa on 100% osseointegration). Minimal principal stress values decreased with increase in osseointegration upon oblique loading for PMMA, BisGMA, and PEEK. Translucent zirconia and lithium disilicate offer a better stress transmission. Minimal principal stress values of PEEK and BisGMA decreased with increasing osseointegration.

Biomechanical Effects of Titanium and Carbon Fiber Reinforced PEEK as Dental Implant Material: A Finite Element Analysis.

The aim of this study is to examine the stresses on the peri-implant bone under occlusal forces of 30% Carbon fiber reinforced PEEK (Cfr-PEEK) and 60% Cfr-PEEK materials that can be used as an alternative to titanium dental implants by finite element analysis. Single-tooth implants of 30% Cfr-PEEK, 60% Cfr-PEEK and titanium were modeled in each of the maxillary anterior, maxilla posterior, mandibular posterior regions. As a result of the applied vertical and oblique forces; Von Misses stress, maximum principal stress and minimum principal stress values and stress distributions in the implant, cortical bone and spongious bone in each of the models were examined. 30% Cfr-PEEK implants stress in the surrounding bone was higher than titanium and 60% Cfr-PEEK implants. The 60% Cfr-PEEK material displayed lower stress distribution on both cortical and spongious peri-implant bone in all models. Titanium and 60% Cfr- PEEK implants exhibited biomechanically similar behavior and these implants conducted stresses to bone more homogeneous than the 30% Cfr-PEEK implants. Overall, oblique forces had more destructive effect than vertical forces and denser bone structure showed better stress distribution against incoming forces. For the routine use of Cfr-PEEK material as dental implant material; animal and long-term clinical studies are needed.

Evaluation of stress distribution of different marginal designs on PEEK and PEKK substructure materials, cortical and cancellous Bone:A finite element analysis

High-performance polymers are used in different fixed prosthesis treatments due to their many advantages such as biocompatibility, shock absorption ability, high fracture resistance. The effects of marginal design on the forces on high-performance polymers are unknown. This study aimed was to investigate the stress distribution of different marginal designs on Polyetheretherketone (PEEK) and Polyetherketoneketone (PEKK) substructure materials, cortical bone and cancellous bone by finite element analysis. A first maxillary molar tooth was modeled in 3D using the "3D Complex Render" method. Considering the ideal preparation conditions (Taper angle was 6°, step depth was 1 mm, occlusal reduction was 2mm), four different configurations were modeled by changing the marginal design (chamfer, deep chamfer, shoulder 90°, shoulder 135°). PEEK, PEKK substructure, and composite superstructure were designed on created models. A total of 150N oblique force from two points and a total of 300N vertical force from three points were applied from occlusall. and the maximum principal stress, minimum principal stress, von Mises stress findings in the cortical bone, spongiose bone, and substructure were examined. The study was carried out by static linear analysis with a three-dimensional finite element stress analysis method. The highest maximum principal stress value in the cortical bone was observed when the PEEK+Shoulder 135° step at vertical force. The highest minimum principal stress value in the cortical bone was observed when the PEEK+Shoulder 90° step, and PEEK+deep chamfer step at oblique force. The highest maximum principal stress value in spongiose bone was observed when the PEEK+Shoulder 90° step. The highest minimum principal stress value in spongiose bone was observed when the PEEK+deep chamfer step at vertical force. The highest von Mises stress value in the substructure was observed when the PEKK+Deep chamfer step at oblique force. The lowest maximum principal stress value in the cortical bone was observed when the PEKK+Shoulder 135° step at oblique force. The lowest minimum principal stress value in the cortical bone was observed when the PEEK+Shoulder 135° step, and PEKK+shoulder 135° step at vertical force. The lowest maximum principal stress value in spongiose bone was observed when the PEEK+Shoulder 90° step. The lowest minimum principal stress value in spongiose bone was observed when the PEEK+Shoulder 135° step and PEKK+Shoulder 135° step at vertical force. The lowest von Mises stress value in the substructure was observed when the PEEK+Deep chamfer step at vertical force. When cortical and spongiose bone stress were evaluated, no destructive stress was observed. Considering the stresses occurring in the substructure the highest stress was observed in the chamfer step.

A finite element model for predicting impact-induced damage to a skin simulant

A finite element model was developed for assessing the efficacy of rugby body padding in reducing the risk of sustaining cuts and abrasions. The model was developed to predict the onset of damage to a soft tissue simulant from concentrated impact loading (i.e., stud impact) and compared against a corresponding experiment. The damage modelling techniques involved defining an element deletion criterion, whereby those on the surface of the surrogate were deleted if their maximum principal stress reached a predefined value. Candidate maximum principal stress values for element deletion criteria were identified independently from puncture test simulations on the soft tissue simulant. Experimental impacts with a stud were carried out at three energies (2, 4 and 6 J), at three angular orientations (0°, 15° and 30°) and compared to corresponding simulations. Suitable maximum principal stress values for element deletion criteria settings were first identified for the 4 J impact, selecting the candidates that best matched the experimental results. The same element deletion settings were then applied in simulations at 2 and 6 J and the validity of the model was further assessed (difference < 15% for the force at tear and < 30% for time to tear). The damage modelling techniques presented here could be applied to other skin simulants to assess the onset of skin injuries and the ability of padding to prevent them.

Dental Versus Zygomatic Implants in the Treatment of Maxillectomy: A Finite Element Analysis.

This study analyzed the stress distributions on zygomatic and dental implants placed in the zygomatic bone, supporting bones, and superstructures under occlusal loads after maxillary reconstruction with obturator prostheses. A total of 12 scenarios of 3-dimensional finite element models were constructed based on computerized tomography scans of a hemimaxillectomy patient. Two obturator prostheses were analyzed for each model. A total force of 600 N was applied from the palatal to buccal bones at an angle of 45°. The maximum and minimum principal stress values for bone and von Mises stress values for dental implants and prostheses were calculated. When zygomatic implants were applied to the defect area, the maximum principal stresses were similar in intensity to the other models; however, the minimum principal stress values were higher than in scenarios without zygomatic implants. In models that used zygomatic implants in the defect area, von Mises stress levels were significantly higher in zygomatic implants than in dental implants. In scenarios where the prosthesis was supported by tissue in the nondefect area, the maximum and minimum principal stress values on cortical bone were higher than in scenarios where implants were applied to defect and nondefect areas. In patients who lack an alveolar crest after maxillectomy, a custom bar-retained prosthesis placed on the dental implant should reduce stress on the zygomatic bone. The stress was higher on zygomatic implants without alveolar crest support than on dental implants.

Static and dynamic stress analysis of different crown materials on a titanium base abutment in an implant-supported single crown: a 3D finite element analysis

BackgroundThis Finite Element Analysis was conducted to analyze the biomechanical behaviors of titanium base abutments and several crown materials with respect to fatigue lifetime and stress distribution in implants and prosthetic components.MethodsFive distinct designs of implant-supported single crowns were modeled, including a polyetheretherketone (PEEK), polymer-infiltrated ceramic network, monolithic lithium disilicate, and precrystallized and crystallized zirconia-reinforced lithium silicates supported by a titanium base abutment. For the static load, a 100 N oblique load was applied to the buccal incline of the palatal cusp of the maxillary right first premolar. The dynamic load was applied in the same way as in static loading with a frequency of 1 Hz. The principal stresses in the peripheral bone as well as the von Mises stresses and fatigue strength of the implants, abutments, prosthetic screws, and crowns were assessed.ResultsAll of the models had comparable von Mises stress values from the implants and abutments, as well as comparable maximum and minimum principal stress values from the cortical and trabecular bones. The PEEK crown showed the lowest stress (46.89 MPa) in the cervical region. The prosthetic screws and implants exhibited the highest von Mises stress among the models. The lithium disilicate crown model had approximately 9.5 times more cycles to fatique values for implants and 1.7 times more cycles to fatique values for abutments than for the lowest ones.ConclusionsWith the promise of at least ten years of clinical success and favorable stress distributions in implants and prosthetic components, clinicians can suggest using an implant-supported lithium disilicate crown with a titanium base abutment.

Biomechanical behavior of all-on-4 concept and alternative designs under different occlusal load configurations for completely edentulous mandible: a 3-D finite element analysis

The aim of this study was to evaluate the effect of the All-on-4 design and 4 alternative implant-supported fixed prosthesis designs on stress distribution in implants, peri-implant bone, and prosthetic framework in the edentulous mandible under different loading conditions using three-dimensional finite element analysis (3D-FEA).Five different experimental finite element models (Model A (unsplinted 6), Model B (splinted 6), Model C (All-on-4), Model D (axial; 2 anterior, 2 posterior), and Model E (4 interforaminal)) were created. Three different loading conditions were applied (canine loading, unilateral I-loading, and unilateral II-loading). The highest minimum (Pmin) and the maximum (Pmax) principal stress values were acquired for cortical and trabecular bones; the highest von Mises (mvM) stress values were obtained for implants and metal frameworks. Model B and Model D showed the most favorable stress distribution. The All-on-4 design (Model C) also showed acceptable stress values close to those of Model B and Model D in the cortical and trabecular bones. In accordance with the stress values in the bone structure, the lowest stress values were measured in the implants and Co-Cr framework in Model B and Model D. The highest stress values in all structures were measured for unilateral loading- II, while the lowest values were found for canine loading. It was concluded that Model B and Model D experimental models showed better biomechanical performance in all structures. Furthermore, the use of a splinted framework, avoiding cantilevers, results in lower stress transmission. On the other hand, canine loading and unilateral loading-I exhibited the best loading conditions.

Seismic Response of RC Beam-Column Joints Strengthened with FRP ROPES, Using 3D Finite Element: Verification with Real Scale Tests

A 3D-finite element analysis within the numerical program ABAQUS is adopted in order to simulate the seismic behavior of reinforced concrete beam-column joints and beam-column joints strengthened with CFRP ropes. The suitability of the adopted approach is investigated herein. For this purpose, experimental and numerical cyclic tests were performed. The experiments include four reinforced concrete (RC) joints with the same ratio of shear closed-stirrup reinforcement and two different volumetric ratios of longitudinal steel reinforcing bars. Two joints were tested as-built, and the other two were strengthened with CFRP ropes. The ropes were applied as Near Surface Mounted (NSM) reinforcement, forming an X-shape around the joint body and further as flexural reinforcement at the top and bottom of the beam. The purpose of the externally mounted CFRP ropes is to allow the development of higher values of concrete principal stresses inside the joint core, compared with the specimens without ropes, and also to reduce the developing shear deformation in the joint. From the results, it is concluded that X-shaped ropes reduced the shear deformation in the joint body remarkably, especially in high drifts. Further, as a result of the comparisons between the yielded outcome from the attempted nonlinear analysis and the observed response from the tests, it is deduced that the adopted method sufficiently describes the whole behavior of the RC beam-column connections. In particular, comparisons between experimental and numerical results of principal stresses developing in the joint body of all examined specimens, along with similar comparisons of force displacement envelopes and shear deformations of the joint body, confirmed the adequacy of the applied finite element approach for the investigation of the use of CFRP-ropes as an efficient and easy-to-apply strengthening technique. The findings also reveal that the connections that have been strengthened with the FRP ropes demonstrated improved performance, and the crack system preserved its load capacity during the reversal loading tests.

Failure strength of glacier ice inferred from Greenland crevasses

Abstract. Ice fractures when subject to stress that exceeds the material failure strength. Previous studies have found that a von Mises failure criterion, which places a bound on the second invariant of the deviatoric stress tensor, is consistent with empirical data. Other studies have suggested that a scaling effect exists, such that larger sample specimens have a substantially lower failure strength, implying that estimating material strength from laboratory-scale experiments may be insufficient for glacier-scale modeling. In this paper, we analyze the stress conditions in crevasse onset regions to better understand the failure criterion and strength relevant for large-scale modeling. The local deviatoric stress is inferred using surface velocities and reanalysis temperatures, and crevasse onset regions are extracted from a remotely sensed crevasse density map. We project the stress state onto the failure plane spanned by Haigh–Westergaard coordinates, showing how failure depends on mode of stress. We find that existing crevasse data are consistent with a Schmidt–Ishlinsky failure criterion that places a bound on the absolute value of the maximal principal deviatoric stress, estimated to be 158±44 kPa. Although the traditional von Mises failure criterion also provides an adequate fit to the data with a von Mises strength of 265±73 kPa, it depends only on stress magnitude and is indifferent to the specific stress state, unlike Schmidt–Ishlinsky failure which has a larger shear failure strength compared to tensile strength. Implications for large-scale ice flow and fracture modeling are discussed.

Mechanism and deformation behavior of elliptical vibration-assisted cutting of FeNiCrCoAl high entropy alloy

The mechanical response of FeNiCrCoAl high entropy alloy (HEA) under conventional cutting and ultrasonic elliptical vibration-assisted cutting (UEVAC) was investigated using molecular dynamics (MD) methods. The effects of vibration period, axial amplitude, and normal amplitude on the material removal mechanism were studied. The results show that the average cutting temperature of the workpiece under UEVAC is significantly higher than that under conventional cutting. The high-temperature distribution area under UEVAC presents an intermittent distribution pattern, which not only facilitates the cutting process but also plays a positive role in the protection of the tool. Furthermore, as the vibration period shortens, both the average principal stress experienced by the workpiece and the triaxial cutting force decrease, while the height and quantity of chip atoms significantly increase. When the vibration period is shortened to 5 ns, the number of chip atoms is about twice that of conventional cutting, which is equivalent to doubling the removal efficiency of the material. Although an increase in axial amplitude causes an increase in the average temperature of the workpiece, it also results in larger negative principal stress. When the axial amplitude A increases to 20 Å, the peak value of the negative principal stress generated inside the base material exceeds 8000 GPa, and the triaxial cutting force tends to increase, without a significant increase in the number of chip atoms. With the increase in normal amplitude B, the average cutting temperature of the matrix also increases. But there is no significant change in the direction and magnitude of the principal stress, and the triaxial cutting force continuously increases. This study provides a theoretical basis for achieving high surface quality of HEAs.

Analysis of Stress Distribution and Displacement Based on the Miniscrew Positions of the Palatal Slope Bone-borne Expander: A Finite Element Study.

This study aimed to investigate the stress distribution pattern of the palatal slope bone-borne expander on the maxillary area according to a different anteroposterior position of anchored miniscrews using finite element analysis. Nasomaxillary stereolithography files with three different anteroposterior anchored miniscrew positions of the palatal slope bone-borne expander were determined as model A, B, and C. Each model consists of four supported miniscrews. Model A: two anterior miniscrews were located between the maxillary canine and the first premolar, and two posteriors between the second premolar and the first molar. Model B: two anteriors were between the lateral incisor and the canine, and two posteriors were the same as in model A. Model C: two anteriors were the same as in model A, and two posteriors were distal to the first molar. One turn of expander screws was applied. Maximum principal stress, equivalent elastic strain, equivalent von Mises stress, and transverse displacement were evaluated. The maximum principal stress was mostly found at the bone-miniscrew interface. Model A exhibited an intersecting area of stress between the supported miniscrews. The highest value of principal stress was in model B, while model C showed a uniform distribution pattern. The elastic strain pattern was similar to the principal stress in all models. The highest value of equivalent von Mises stress was located on the expander screw. The largest amount of transverse displacement of teeth was in model A, while model C exhibited a more consistent transverse displacement than other models. Vertical displacement of posterior teeth was also noticed. Based on the result, it revealed that the various anteroposterior miniscrew placements of the palatal slope bone-borne expander had various patterns of stress distribution and resulted in various outcomes. It may be inferred that model A's miniscrew location was advantageous for obtaining expansion quantities, but model C's miniscrew position was advantageous for maintaining consistent biomechanics.

Dental versus zygomatic implants in the treatment of maxillectomy: a finite element analysis.

This study analyzed the stress distributions on zygomatic and dental implants placed in the zygomatic bone, supporting bones, and superstructures under occlusal loads after maxillary reconstruction with obturator prostheses. 12 scenarios of three-dimensional finite element models were constructed based on computed tomography scans of a patient who had hemimaxillectomy. Two obturator prostheses were analyzed for each model. A total force of 600 N was applied from the palatal to buccal bones at an angle of 45°. The maximum and minimum principal stress values for bone and also the von Misses stress values for dental implants and prostheses were calculated. When zygomatic implants were applied to the defect area, the maximum principal stresses were similar in intensity to the other models; however, the minimum principal stress values were higher than in scenarios without zygomatic implants. In models that used zygomatic implants in the defect area, von Misses stress levels were significantly higher in zygomatic implants than in dental implants. In scenarios where the prosthesis was supported by tissue in the non-defect area, the maximum and minimum principal stress values on cortical bone were higher than in scenarios where implants were applied to both defect and non-defect areas. In patients who lack an alveolar crest after maxillectomy, reduced stress on the zygomatic bone is expected if a custom bar-retained prosthesis is placed on the dental implant. The stress was higher on zygomatic implants without alveolar crest support than on dental implants.

The Distribution Law of Ground Stress Field in Yingcheng Coal Mine Based on Rhino Surface Modeling

The distribution law of the ground stress field is of great significance in guiding the design of coal mine roadway alignment, determining the parameters of roadway support, and preventing and controlling the impact of ground pressure in coal mines. A geostress inversion method combining Rhino surface modeling and FLAC3D 6.0 numerical simulation software is proposed. Based on the geological data of the coal mine and the results of on-site measurements, a three-dimensional geological model of Yingcheng Coal Mine is established for the geostress inversion, and the distribution law of the geostress field in Yingcheng Coal Mine is obtained. Research shows the following: (1) The horizontal maximum principal stress values of the Yingcheng Mine are between 33.9 and 35.3 MPa, the horizontal minimum principal stress values are between 23.6 and 25.4 MPa, and the direction of the horizontal maximum principal stress is roughly in the southwest to west direction; (2) the three-way principal stress magnitude relationship is σH &gt; σv &gt; σh, indicating that the horizontal stress dominates in the study area, which belongs to the slip-type stress state; (3) The maximum principal stress of No. 3 coal seam is 33.1–34.8 MPa, the middle principal stress is 27.5–29.2 MPa, and the minimum principal stress is 17.3–22.9 MPa. Due to the influence of topography and burial depth, there is a phenomenon of stress concentration in some areas. By comparing the inversion values with the measured values, the accuracy of the geostress inversion is high, and the initial geostress inversion method based on Rhino surface modeling accurately inverts the geostress distribution pattern of the Yingcheng coal mine.

Azimuthal pore pressure response to teleseismic waves: effects of damage and stress anisotropy

SUMMARY Pore pressure oscillations induced by stress variations, including propagating seismic waves from remote earthquakes, have been widely observed in various groundwater systems. The monitored pressure change in wells shows significant water-level oscillations to volumetric strain as well as to S and Love waves. Recent observations demonstrated azimuthal dependence of the pore pressure oscillations with respect to stress indicators and fault zone orientation. Within the fault zone, damage-induced anisotropy is the result of the alignment and orientation of cracks and other internal flaws within the rock. In this work, we provide a complete quantitative description of the pore pressure changes induced by passing seismic waves associated with different orientations and values of principal stress and damage tensor components. The model quantifies the azimuthal dependence of the pore pressure response by a non-dimensional ratio defined as the amplitude of the pressure oscillations induced by a shear strain normalized to the volumetric strain. Three angles and two values are needed to calculate the azimuthal dependence of the pore pressure response: the angle between the directions of the maximum horizontal stress and the seismic event; fault zone orientation; microcrack orientation within the fault zone; and damage and stress values. The model predicts that maximum pore pressure response occurs when microcracks and maximum horizontal stress are in the same orientation, high damage and high stress anisotropy. By adjusting these quantities, we recalculate results of recent seismological studies in the Arbuckle disposal well, Osage County, Oklahoma. The presented model successfully predicts the observed azimuthal dependence in wave-induced fluid pressure response and relates the anisotropic response to tectonic indicators such as the orientations of the maximum horizontal stress, fault zone, and microfractures.

Stress Distribution on Prepared Tooth With Shoulder and Radial Shoulder Margin to Receive Crowns of Three Different Materials: A Finite Element Analysis.

Aim and background This study aims to determine the stress distribution on the prepared tooth at the margins with shoulder and radial shoulder finish lines when an occlusal load of 300N was applied to ceramic, zirconia, and polyether ether ketone (PEEK) crowns. Materials and methods Six models of mandibular first molar teeth were fabricated. The tooth models were subdivided into two groups with shoulder and radial shoulder margins, respectively (n = 18). The teeth were restored with three different prosthetic crown materials (ceramic, zirconia, and PEEK). To simulate the typical forces experienced by a prosthetic crown material in a lower posterior tooth during chewing and biting, an occlusal load of 300N was applied to each of the samples, and the maximum principal stress (Pmax) and von Mises stress were calculated, respectively. These samples were then compared and evaluated to determine the material best suited as a prosthetic crown material of choice for a lower posterior tooth. Results Among the materials used, the maximum principal stress value was the least in PEEK crowns. The von Mises stress value was highest for the zirconia crown with shoulder margin and was least for the PEEK crown with a similar margin. Conclusion PEEK as a crown material was found to be a better choice for lower posterior teeth as there was the least maximum principal stress at the margin, irrespective of either shoulder or radial shoulder finish line used.

Stress field-aware infill toolpath generation for additive manufacturing of continuous fiber reinforced polymer composites

The infill toolpath utilized in continuous fiber reinforced polymer composites via additive manufacturing (CFRPCs-AM) significantly influences the mechanical performance of printed structures. However, existing infill toolpath for CFRPCs-AM are primarily designed for 2D planar structures and do not account for 3D shell structures with complex shapes or load path dependent characteristics. To address these limitations, this paper proposes an explicit streamline tracing method to convert the stress field into adaptive infill toolpaths for CFRPCs-AM. The method leverages principal stress direction and value fields to control toolpath density and distribution while considering the minimum allowable bead width constraint. Additionally, the geodesic distance is employed to precisely represent the distance between adjacent infill toolpaths on shell structures. Experimental validation on 2D and 3D complex structures under varying conditions demonstrates the effectiveness of the proposed method, which significantly improves stiffness and strength by 200–300% compared to traditional uniform toolpaths for CFRPCs-AM.