Vacuum-assisted Drying Research Articles

Ultrasound-assisted vacuum drying of limequat peels and characterization of thermal, morphological and functional properties

This work aimed to determine drying behavior and energy consumption of limequat peels dried using ultrasound-assisted vacuum drying (UAVD), vacuum-assisted drying (VAD), oven drying (OD) and vacuum drying (VD), and investigate thermogravimetric decomposition, morphological, elemental and spectral analyses of dried peels with energy efficiency analysis including specific moisture extraction rate (SMER), moisture extraction rate (MER) and specific energy consumption (SEC). The UAVD considerably shortened drying time by 49 %, 34 % and 15 % as compared to the OD, VAD and VD. The highest drying rate was achieved at the UAVD. The effective moisture diffusivity(Deff) values in descending order were UAVD>VD>VAD>OD. Proximate analysis showed that limequat peels dried using the UAVD had the highest fixed carbon (25.35 %) and ash (3.03 %) contents, but the lowest volatile matter (61.68 %). Dried limequat peels exhibited similar thermal decomposition behavior. The UAVD caused porous and rough surface formation, and microchanneling effect. Carbon (>62.56 %) and oxygen (>15.98 %) were the major elements in dried limequat peels. The lowest O/C (0.25) and H/C (0.85) ratios were obtained for the limequat peels dried using the UAVD. Fourier-transform infrared spectroscopy (FTIR) spectra showed primarily O–H, C–H, CO, CC and C–O–C stretching vibrations. The highest SMER (0.0053 kg/kWh) and MER (0.0012 kg/h) values, and the lowest SEC (188.27 kWh/kg) value were determined for the UAVD. In conclusion, the UAVD was found to be the most appropriate drying method for the drying of limequat peels.

Achieving the low emissivity of graphene oxide based film for micron-level electromagnetic waves stealth application

In recent years, the development of advanced materials with enhanced micron-level electromagnetic waves stealth properties has garnered significant attention due to their applications in fields such as military technology and thermal insulation. This study primarily investigates the stealth characteristics of materials within the 8–14 μm electromagnetic wave band, commonly known as the infrared (IR) spectrum. The effect of metallic Ag nanoparticles on the graphene oxide (GO) was obtained to achieve the excellent IR stealth ability. Specifically, Ag/GO composite films were prepared using a one-step reduction method and vacuum-assisted drying. The IR emissivity (8–14 μm) of the composites was significantly reduced with increasing Ag content, and the electrical conductivity of the materials was enhanced. When the Ag/GO mass ratio in the material was 1:2, the IR emissivity of the material at 8–14 μm was as low as 0.279, which was 62 % lower compared to GO. In addition, IR thermograms of the composites were analyzed using an IR thermographic camera. Obviously, the composites exhibited significant IR stealth properties when compared with those of GO. Thus, this work provides a reference for the preparation of carbon-based low IR emissivity materials for infrared stealth application.

Vacuum-Assisted Drying Process for Screen-Printable Carbon Electrodes of Perovskite Solar Cells with Enhanced Performance Based on Cuprous Thiocyanate as a Hole Transporting Layer.

Carbon-based perovskite solar cells without a hole transport layer (HTL) are considered to be highly stable and of low cost. However, the deficient interface contact and inferior hole extraction capability restrict the further improvement of the device efficiency. Introducing a hole transporting layer, such as cuprous thiocyanate (CuSCN), can enhance the hole extraction ability and improve the interface contact. However, our further studies indicated that-at a certain temperature-for carbon-based solar cells, in the CuSCN layer, the diffusion of SCN- into the perovskite film would produce more interfacial defects and aggravate nonradiative recombination, thus hindering the carrier transport. We further disclosed the reasons for performance attenuation during the thermal treatment of carbon electrodes, proposed a vacuum-assisted drying process for carbon electrodes to suppress the destructive effect, and finally, achieved an enhanced efficiency for perovskite solar cells with a CuSCN inorganic HTL and screen-printable carbon electrode. Also, the unencapsulated perovskite solar cell demonstrated over 80% efficiency retention after being stored in an ambient atmosphere (45-70% relative humidity (RH)) for over 1000 h and maintained over 85% efficiency retention for 309 h of 1-sun irradiation under a continuous nitrogen flow under open-circuit conditions.

Closing the gap - inclusion of ultrashort-chain perfluoroalkyl carboxylic acids in the total oxidizable precursor (TOP) assay protocol.

An improved protocol of the total oxidizable precursor (TOP) assay was developed for precursors to C2-C14 perfluoroalkyl carboxylic acids (PFCAs) and C4-C8 and C10 perfluoroalkyl sulfonic acids (PFSAs). The proposed protocol was tested and validated for contaminated soil samples. The perfluoroalkyl acids (PFAAs) present in the soil extract solutions after oxidation with persulfate were separated from the inorganic salts by vacuum-assisted drying of the digestion solution followed by solid-liquid extraction of the PFAAs with acetonitrile from the dry residue. Ion chromatography (for C2-C4 PFCAs) and reversed phase liquid chromatography (for all other PFASs), both coupled to tandem mass spectrometry, were used for quantification. High procedural recoveries of PFAAs between 68% and 123% with RSDs between 0.2% and 25% (n = 3) were achieved. The method was validated using selected polyfluoroalkyl phosphoric acid esters (PAPs) and bis-[2-(N-ethyl perfluorooctane-1-sulfonamido)ethyl] phosphoric acid ester (diSAmPAP) as model precursors in pure solutions and in the presence of soil matrix. The oxidation led to characteristic and reproducible PFCA patterns (in the case of PAPs) or PFOA (in the case of diSAmPAP) with total reaction yields between 92 ± 4% and 123 ± 13% (n = 3). The impact of the soil matrix on transformation yields was negligible. In a soil core from a PFAS-polluted agricultural site, precursors were concentrated in the upper 40 cm with long-chain precursors being prevalent. After oxidative digestion, the total molar PFAA-concentrations increased by factors of 1.6 to 5.0. More than 40 cm below ground precursors of TFAA, PFPrA and PFBA accounted for ∼50% of the reaction products, underlining the importance of their inclusion in mass balances based on the TOP assay.

Highly efficient flexible solar cells based on a room-temperature processed inorganic perovskite

A vacuum-assisted drying approach to prepare high-quality α-CsPb0.96Bi0.04I3 at room temperature for flexible solar cells was demonstrated.

Comparison of four pretreatments on the drying behavior and quality of taro (Colocasia esculenta L. Schott) slices during intermittent microwave vacuum-assisted drying

ABSTRACTEffect of different pretreatments on drying behavior and quality of taro slices during intermittent microwave vacuum-assisted drying were investigated. Taro slices were subjected to the following pretreatments: blanching (B), blanching and freezing (B + F), blanching and immersion in maltodextrin solution (B + M), and blanching and immersion in maltodextrin solution and freezing (B + M + F). The reduction in amylose content, the increase in amylose to amylopectin ratio, the change of mechanical properties, the increase in sample bulk density and reduction in sample porosity and structure collapse during pretreatment processes facilitated heat and moisture transfer and quality changes during drying of taro slices. During drying process, all the pretreatment reduced the drying time of samples. The drying rate included a warming-up period and a falling rate period. The values of effective moisture diffusivity increased gradually as the moisture content decreased. The B + M + F pretreatment had the shortest drying time, the highest drying rate and the biggest effective moisture diffusivity. Moreover, for B + M + F pretreatment, the parameters including hardness, crispness, color, and microstructure had remarkable changes as compared with the other pretreatments.

Evaluation of the impact of food matrix change on the in vitro bioaccessibility of carotenoids in pumpkin (Cucurbita moschata) slices during two drying processes.

The food matrix is a limiting factor in determining the bioaccessibility of carotenoids. The impact of food matrix change on the bioaccessibility of carotenoids during drying processes is still unknown. The effect of intermittent microwave vacuum-assisted drying (IMVD) and hot air drying (HAD) on the in vitro liberation and micellization of carotenoids in pumpkin slices was studied. This variable depended on the changes of the matrix driven by the drying process. Different changes in the cell morphology and carotenoid distribution of pumpkin slices during the two processing methods were observed. For IMVD, cell wall degradation and complete chromoplast organelle disruption contributed to the improvement in the liberation and micellization of carotenoids. In the HAD-dried sample, large pigment aggregates hindered the liberation of carotenoids. The carotenoid level in the micellar fraction appeared to be lower than that in the aqueous supernatant during the two processes, suggesting that the new obstacles formed during processing and/or digestion hindered the incorporation of carotenoids in mixed micelles.

A simplified method for peptide de novo sequencing using (18)O labeling.

Incorporation of an (18)O atom into a peptide C-terminus by proteolytic cleavage in the presence of H2(18)O is one of the most effective ways of enhancing tandem mass spectrometry (MS/MS)-based de novo sequencing. Incorporation is usually accomplished by procedures including vacuum-assisted drying of tryptic peptides extracted from gels, their subsequent reconstitution in a H2(16)O/H2(18)O mixture and re-treatment with trypsin. In the present work, we propose a simplified procedure for (18)O incorporation into tryptic peptides by adding H2(18)O and trypsin to the original digest solution. In comparison to published methods, the proposed protocol for peptide de novo sequencing brings significant advantages in analysis and workflow with no deterioration in method performance. We show that labeling by this simplified method leads to a highlighting of the y-ion fragment series in the peptide matrix-assisted laser desorption/ionization (MALDI)- MS/MS data, which facilitates MS/MS data interpretation. We also prove that eliminating acid extraction of peptides from gels does not result in a decrease in sequence coverage or a qualitative loss of particular peptides detectable by MALDI-MS. The method was examined by MALDI-MS/MS on bovine serum albumin and recombinant histidine kinase CKI1 from Arabidopsis thaliana, and was verified by de novo sequencing of tryptic peptides originating from Apodemus sylvaticus salivary proteins.

Vacuum-assisted drying of polymer electrolyte membrane fuel cell

Purging a polymer electrolyte membrane fuel cell (PEMFC) with dry N2 to remove water in the catalyst layer and the membrane during shutdown is necessary for ensuring successful startup and avoiding damages from the freeze/thaw cycling during cold-start. However, carrying N2 onboard may be impractical for mobile applications. Vacuum-assisted drying can accelerate and aid in water removal by reducing the boiling point of water, thus enhancing the evaporation and diffusion rate. This method is applied to a single cell PEMFC and compared to purging using dry N2. The drying process was monitored using electrochemical impedance spectroscopy (EIS), and the results were fitted to an equivalent circuit model. Our experimental results show the vacuum-assisted drying method may provide faster and more thorough water removal than N2 purging.