Light Energy Utilization Efficiency Research Articles

Enhancement of photocatalytic degradation of ciprofloxacin via constructing conductive matrix

The application of heterogeneous photocatalysts is severely limited by the high charge transfer resistance (Rct). BiVO4/g-C3N4 photocatalysts were prepared and loaded on the conductive matrix material carbon paper (CP) to reduce electron transfer resistance and improve the photocatalytic performance. The Rct of BiVO4/g-C3N4@CP was remarkedly reduced by 94.3 % compared to the photocatalysts on the oil paper (BiVO4/g-C3N4@OP), while the photocurrent density increased by 5.5 times. The utilization efficiency of light energy and separation of photoelectrons and holes were improved with CP due to its ability to facilitate long-distance transfer of photoelectrons. Consequently, the photocatalytic degradation performance of BiVO4/g-C3N4@CP was enhanced by a 26.1 % improvement in ciprofloxacin (CIP) degradation efficiency. Quenching experiment, LC-MS analysis and DFT calculation revealed that piperazine ring opening and C-F cleavage were the major pathways for CIP degradation with BiVO4/g-C3N4@CP.

Surface-controlled oxygen vacancy-rich Bi/BiVO4 Schottky junction for highly selective and active photocatalytic nitrogen fixation

The modulation of active site density and localized electron concentration represents a crucial step in enhancing nitrogen activation, thereby significantly augmenting the efficiency of photocatalytic nitrogen fixation. In this paper, Bi/BiVO4 Schottky junctions enriched with oxygen vacancies (Bi/Vo-BVO) were fabricated by in situ reduction. Compared to BiVO4, Bi/Vo-BVO composites exhibited 8.4-fold enhancement in ammonia synthesis yield, reaching a maximum rate of 167.74 μmol·g−1·h−1. In situ FTIR spectroscopy and isotopic labeling experiments definitively demonstrated that the nitrogen constituent of NH4+ is derived from N2. N2-TPD and DFT calculation collectively suggest that the surface of Bi/Vo-BVO, enriched with ligand-unsaturated V4+ species, furnishes a substantial array of chemisorption sites for N2 molecules, attributed to the abundance of oxygen vacancies. In situ XPS coupled with DFT corroborate that the photoexcited electrons within the BiVO4 valence band accumulate in the conduction band, thereby directly facilitating the activation of N2 adsorbed at the V4+ active sites; The built-in electric field established at the interface between Bi and BiVO4 substantially facilitates the enrichment of Bi-emitted thermal electrons within oxygen vacancies on BiVO4 surface. These electrons subsequently migrate towards and interact with the adsorbed N2 via the V4+ active sites. The synergistic photothermal electrons activation mechanism of N2 not only enhances the efficiency of light energy utilization but maximizes the catalytic efficacy of the photocatalyst through the full exploitation of its intrinsic catalytic potential.

A magnetic plasma Fe3O4@Cu@Cu2O photoelectrochemical sensor for the detection of fumonisin B1.

Fumonisin B1 (FB1) is a mycotoxin, a water-soluble metabolite produced by Fusarium cepacia, which mainly contaminates grain and its products and is acutely toxic and potentially carcinogenic to certain domestic animals. In this work, plasma nanocomposites of Fe3O4@Cu@Cu2O with magnetic and optoelectronic properties were synthesized as a sensing platform. On one hand, the surface plasmon resonance (SPR) of metallic Cu accelerates the electron transfer rate. On the other hand, plasma-induced resonance energy transfer of metals and semiconductors can improve the utilization efficiency of light energy. A split photoelectrochemical (PEC) sensor based on Fe3O4@Cu@Cu2O was proposed for the detection of FB1. The sensor has a wide linear range of 1.0-10 000 pg mL-1 and a low detection limit of 0.28 pg mL-1 (LOD, S/N = 3), which can realize the specific detection of FB1 in real samples.

Measurement of interfacial charge transfer rate during visible light CO2 reduction under bias voltage conditions

The study of photogenerated electron transfer pathway and time scale in photoelectrocatalysis is the key factor to improve the efficiency of light energy utilization. At present, the reduction of CO2 by visible light is one of the hotspots of research, but it is difficult to determine the reduction reaction and mechanism. Therefore, we use electrochemical in situ growth technology to prepare Bi2(MoO4)3, and then use photoelectrocatalytic method to reduce CO2. The results show that the rate of charge transfer at the interface is about 10−18 cm4/s in the reduction of CO2 by visible light under bias voltage, and the catalyst can react stably for 10 h. This provides a way to optimize the photogenerated electron transfer model and to design the catalysts for the reduction of carbon dioxide under visible light.

Photosynthetic response of Chlamydomonas reinhardtii and Chlamydomonas sp. 1710 to zinc toxicity.

Zinc (Zn) is an essential trace element but can lead to water contamination and ecological deterioration when present in excessive amounts. Therefore, investigating the photosynthetic response of microalgae to Zn stress is of great significance. In this study, we assessed the photosynthetic responses of neutrophilic Chlamydomonas reinhardtii and acidophilic Chlamydomonas sp. 1710 to Zn exposure for 96 h. The specific growth rate (μ), chlorophyll-a (Chl-a) content, and chlorophyll fluorescence parameters were determined. The results demonstrated that Chlamydomonas sp. 1710 was much more tolerant to Zn than C. reinhardtii, with the half-maximal inhibitory concentration (IC50) values of 225.4 mg/L and 23.4 mg/L, respectively. The μ and Chl-a content of C. reinhardtii decreased in the presence of 15 mg/L Zn, whereas those of Chlamydomonas sp. 1710 were unaffected by as high as 100 mg/L Zn. Chlorophyll fluorescence parameters indicated that the regulation of energy dissipation, including non-photochemical quenching, played a crucial role in Zn stress resistance for both Chlamydomonas strains. However, in the case of C. reinhardtii, non-photochemical quenching was inhibited by 5 mg/L Zn in the first 48 h, whereas for Chlamydomonas sp. 1710, it remained unaffected under 100 mg/L Zn. Chlamydomonas sp. 1710 also exhibited a 20 times stronger capacity for regulating the electron transfer rate than C. reinhardtii under Zn stress. The light energy utilization efficiency (α) of Chlamydomonas sp. 1710 had the most highly non-linear correlation with μ, indicating the energy utilization and regulation process of Chlamydomonas sp. 1710 was well protected under Zn stress. Collectively, our findings demonstrate that the photosystem of Chlamydomonas sp. 1710 is much more resilient and tolerant than that of C. reinhardtii under Zn stress.

Changes in Photosynthetic Characteristics between Green-Leaf Poplar Linn. "2025" and Its Bud-Sporting Colored-Leaf Cultivars.

Colored-leaf poplar is increasingly popular due to its great ornamental values and application prospects. However, the photosynthetic characteristics of these colored-leaf cultivars have not been well understood. In this study, the photosynthetic differences between green-leaf poplar Populus deltoids Linn. "2025" (L2025) and colored-leaf cultivars 'Zhonghong poplar' (ZHP), 'Quanhong poplar' (QHP), and 'Caihong poplar' (CHP) were investigated on several levels, including chloroplast ultrastructure observation, photosynthetic physiological characteristics, and expression analysis of key genes. The results showed that the photosynthetic performance of ZHP was basically consistent with that of L2025, while the ranges of light energy absorption and efficiency of light energy utilization decreased to different degrees in CHP and QHP. A relatively low water use efficiency and high dark respiration rate were observed in QHP, suggesting a relatively weak environmental adaptability. The differences in chloroplast structure in different colored-leaf poplars were further observed by transmission electron microscopy. The disorganization of thylakoid in CHP was considered an important reason, resulting in a significant decrease in chlorophyll content compared with other poplar cultivars. Interestingly, CHP exhibited extremely high photosynthetic electron transport activity and photochemical efficiency, which were conductive to maintaining its relatively high photosynthetic performance. The actual quantum yield of PSII photochemistry of ZHP was basically the same as that of QHP, while the relatively high photosynthetic performance indexes in ZHP suggested a more optimized photosynthetic apparatus, which was crucial for the improvement of photosynthetic efficiency. The differential expressions of a series of key genes in different colored-leaf poplars provided a reasonable explanation for anthocyanin accumulation and specific photosynthetic processes.

Construction of NiS/MnCdS S-scheme heterojunction for efficient photocatalytic overall water splitting: Regulation of surface sulfur vacancy and energy band structure

The overall water splitting based on specific photocatalysts is one of the ultimate ways to solve the energy and environmental crisis facing humanity. Sulfide photocatalysts have greater potential in photocatalytic production of solar fuel. However, due to its easy photocorrosion phenomenon, it not effectively driving the water oxidation semi-reaction to produce oxygen, so how to use sulfide photocatalyst to decompose pure water to achieve stoichiometric reaction of H2/O2 production remains a quite challenging task. Herein, sulfur vacancies-rich MnCdS nanoparticles were modified with NiS nanosheets through the hydrothermal derivation method. Different concentration gradients of sulfur-vacancy in MnCdS nanoparticles (MnCdS-Vs-X) with tunable band structures were successful prepared by regulating the concentration of hydrazine hydrate, thus improves the efficiency of light energy utilization and charge separation and the existence of S defects was verified by transmission electron microscopy (TEM) and electron paramagnetic resonance (EPR). The density function theory (DFT) calculation bears out that the draw into of S vacancy adjusted the band structure of MnCdS. Moreover, the successful construction of an S-scheme heterojunction between NiS and MnCdS-Vs-3 has been strongly demonstrated by in-situ XPS and UPS, which promoted interfacial charge separation and further improved the photocatalytic hydrogen evolution efficiency. The as-obtained S-scheme 20 %NiS/MnCdS-Vs-3 heterojunction exhibit excellent visible-light H2 production activity of 4099.55 μmol g−1h−1, 6.75 times higher than pure MnCdS. Most importantly, the excellent and stable photocatalytic overall water splitting activity of H2-509.70 μmol g-1h−1/O2-254.90 μmol g-1h−1 were obtained over 20 % NiS/MnCdS-Vs-3, which further demonstrates the application value of NiS/MnCdS-Vs-3 photocatalysts. This work proposes new ideas for the application of S-vacancies and S-scheme heterojunction in addressing the stability issues associated with sulfide-based photocatalysts in photocatalytic water splitting.

Ocean acidification detrimentally affects mineralization and photosynthetic efficiency of the brown alga Padina pavonica at a CO2 vent

Increasing atmospheric CO2 concentrations are causing ocean acidification potentially leading to significant consequences for marine organisms, particularly those that build calcium carbonate skeletons, shells, and tests. In the present study, we examined the effects of decreasing pH on the photosynthetic efficiency and spectral reflectance of the calcifying alga Padina pavonica naturally occurring along a natural pH gradient generated by a CO2 vent near the Island of Panarea (Italy). Based on the photoacoustic determination of photosynthetic light energy utilization efficiency, we found that the photosynthetic efficiency of P. pavonica decreased with decreasing pH. In the most acidified sites, calcium carbonate across the algae decreased while the changes in absorption light at 483 nm (carotenoids) in relation to green light (562 nm) ratio indicate an increase in the contribution of carotenoids to algal pigments towards the more acidic sites. Here we show, for the first time, the effects of seawater acidification on the optical properties of a Mediterranean calcifying phototroph under low pH conditions at CO2 vents.

A spatial carrier dynamic quantitative differential phase imaging method

Differential interference contrast (DIC) microscopy is an important method for quantitative phase imaging (QPI) due to its high compatibility regarding to partial coherent light illumination and excellent optical sectioning ability. However, limited by the on-axis interferometric configuration of Nomarski DIC microscopic imaging system, it is difficult to achieve single-shot phase retrieval. Here, we propose a simple and efficient method for dynamic quantitative differential phase imaging (QDPI) by introducing a spatial carrier device into DIC microscope. A Wollaston prism (WP) is placed on the imaging plane of DIC microscope and then projected by a 4f imaging system, so two orthogonally polarized imaging beams with a certain shearing amount will interfere on the conjugate plane of the 4f imaging system and form a spatial carrier DIC image, thus the QDPI can be conveniently realized. Importantly, the system not only possesses high temporal phase stability provided by the common-path geometries and low spatial phase noise due to partially coherent light illumination, but also the advantages of simple optical implementation, no additional phase distortion, high light energy utilization efficiency, and high signal-to-noise ratio. The experimental result demonstrates that using the proposed method, the phase measurement sensitivity reaches 0.003 rad, the corresponding applicability is verified by a polystyrene microsphere crown and biological cells.

Photocatalytic properties and antibacterial mechanisms of microbial-derived ZnS/CuS nanocomposites

The urgency to combat antibiotic-resistant bacterial infections requires new antibacterial materials and methods. Utilizing Shewanella onesidensis metabolism, biological zinc/copper sulfide (bio-ZnS/CuS) composites with excellent visible-light photocatalysis effects and broad-spectrum antibacterial activity were synthesized. During synthesis, over 95% of heavy metal ions were recovered from wastewater through co-precipitation to form metal sulfides. The biocomposite with Zn/Cu ratio at 1/9 (Zn1S/Cu9S) showed the best photocatalytic performance. Under visible-light catalysis of Zn1S/Cu9S, 98.02 ± 0.13% of methylene blue and 81.74 ± 2.12% of rhodamine B were rapidly removed, while sterilization rates exceeded 99.99% against Escherichia coli and 99.98% against Staphylococcus aureus. The biocomposite showed a nanostructure with sizes between 5 and 20 nm. Characterizations including X-ray photoelectron spectroscopy, UV-Vis absorption spectra, and photoluminescence spectra proved its excellent visible light response capacity (>400 nm) and energy utilization efficiency. Scavenging experiments demonstrated photogenerated holes and hydrogen peroxide as the major reactive oxygen species (ROS) that induce bacterial death. Toxicological studies revealed that ROS attacked bacterial cells by damaging membranes, inhibiting energy metabolism, breaking the antioxidant defense system, and compromising DNA integrity. This research presents innovative solutions for tackling bacterial infections and heavy metal contamination through the advancement of microbial synthetic functional nanomaterials.

Regulatory effects of silicon nanoparticles on the growth and photosynthesis of cotton seedlings under salt and low-temperature dual stress

BackgroundSilicon nanoparticles (SiO2-NPs) play a crucial role in plants mitigating abiotic stress. However, the regulatory mechanism of SiO2-NPs in response to multiple stress remains unclear. The objectives of this study were to reveal the regulatory mechanism of SiO2-NPs on the growth and photosynthesis in cotton seedlings under salt and low-temperature dual stress. It will provide a theoretical basis for perfecting the mechanism of crop resistance and developing the technology of cotton seedling preservation and stable yield in arid and high salt areas.ResultsThe results showed that the salt and low-temperature dual stress markedly decreased the plant height, leaf area, and aboveground biomass of cotton seedlings by 9.58%, 15.76%, and 39.80%, respectively. While SiO2-NPs alleviated the damage of the dual stress to cotton seedling growth. In addition to reduced intercellular CO2 concentration, SiO2-NPs significantly improved the photosynthetic rate, stomatal conductance, and transpiration rate of cotton seedling leaves. Additionally, stomatal length, stomatal width, and stomatal density increased with the increase in SiO2-NPs concentration. Notably, SiO2-NPs not only enhanced chlorophyll a, chlorophyll b, and total chlorophyll content, but also slowed the decrease of maximum photochemical efficiency, actual photochemical efficiency, photochemical quenching of variable chlorophyll, and the increase in non-photochemical quenching. Moreover, SiO2-NPs enhanced the activities of ribulose-1,5-bisphosphate carboxylase/oxygenase and phosphoenolpyruvate carboxylase, improved leaf water potential, and decreased abscisic acid and malondialdehyde content. All the parameters obtained the optimal effects at a SiO2-NPs concentration of 100 mg L− 1, and significantly increased the plant height, leaf area, and aboveground biomass by 7.68%, 5.37%, and 43.00%, respectively. Furthermore, significant correlation relationships were observed between photosynthetic rate and stomatal conductance, stomatal length, stomatal width, stomatal density, chlorophyll content, maximum photochemical efficiency, actual photochemical efficiency, photochemical quenching of variable chlorophyll, and Rubisco activity.ConclusionThe results suggested that the SiO2-NPs improved the growth and photosynthesis of cotton seedlings might mainly result from regulating the stomatal state, improving the light energy utilization efficiency and electron transport activity of PSII reaction center, and inducing the increase of Rubisco activity to enhance carbon assimilation under the salt and low-temperature dual stress.

Comparative Evaluation of the Effect of Copper Oxide and Copper Sulfate Nanoparticles on Structural and Functional Characteristics of Thalassiosira weissflogii under Conditions of Enrichment Cultivation // Russian Journal of Plant Physiology.

The effect of copper oxide nanoparticles (500, 1000, 2000 μg/L) and copper ions (37.5, 75, 150 μg/L) on the morphological, structural-functional, and fluorescent parameters of diatom microalgae Thalassiosira weissflogii under conditions of long-term cultivation was studied. It was shown that copper in ionic form is more toxic for this microalgae species than in the form of a nanooxide. The nature of the effect of copper in ionic and nanoform on cells Thalassiosira weissflogii has both similarities and significant differences. The difference in the effect of the studied toxicants on the growth of algae and the performance of photosynthetic apparatus was revealed. The addition of copper ions into the cultivation medium led to long lag phase during the initial stage of the experiment, followed by the restoration of growth on days 3–6 of exposure. An increase in the concentration of copper oxide nanoparticles in the medium caused inhibition of algae growth without a pronounced lag phase. With an increase in the concentration of Cu2+ in the culture medium, a decrease in the quantum efficiency of light energy utilization by the PS II photosynthetic complex and the maximum relative electron transport rate were observed, while copper oxide nanoparticles had an insignificant effect on the efficiency of the photosynthetic apparatus ofThalassiosira weissflogii. With an increase in the concentration of copper, both in the ionic form and in the form of nanooxide, increase in cell volume, changes of cell shape and granularity, an increase in the production of reactive oxygen species, suppression of enzymatic activity and a decrease in autofluorescence values of individual cells in the red region of the spectrum were observed.

In Situ Growth of CdZnS Nanoparticles@Ti3C2Tx MXene Nanosheet Heterojunctions for Boosted Visible-Light-Driven Photocatalytic Hydrogen Evolution.

Using natural light energy to convert water into hydrogen is of great significance to solving energy shortages and environmental pollution. Due to the rapid recombination of photogenerated carriers after separation, the efficiency of photocatalytic hydrogen production using photocatalysts is usually very low. Here, efficient CdZnS nanoparticles@Ti3C2Tx MXene nanosheet heterojunction photocatalysts have been successfully prepared by a facile in situ growth strategy. Since the CdZnS nanoparticles uniformly covered the Ti3C2Tx Mxene nanosheets, the agglomeration phenomenon of CdZnS nanoparticles could be effectively inhibited, accompanied by increased Schottky barrier sites and an enhanced migration rate of photogenerated carriers. The utilization efficiency of light energy can be improved by inhibiting the recombination of photogenerated electron-hole pairs. As a result, under the visible-light-driven photocatalytic experiments, this composite achieved a high hydrogen evolution rate of 47.1 mmol h-1 g-1, which is much higher than pristine CdZnS and Mxene. The boosted photocatalytic performances can be attributed to the formed heterojunction of CdZnS nanoparticles and Ti3C2Tx MXene nanosheets, as well as the weakened agglomeration effects.

Polypyrrole-decorated ZnO/g-C3N4 S-scheme photocatalyst for rhodamine B dye degradation: Mechanism and antibacterial activity

Polypyrrole (PPy) and graphitic carbon nitride (g-C3N4) nanoparticles are added to the surface of ZnO nanorods to successfully produce a Step-scheme (S-scheme) photocatalytic system known as g-C3N4/PPy/ZnO (GPZ) by a multistep process: hydrothermal and calcination processes, followed by polymerization. During the formation of the heterojunction, the oxygen vacancy (OV) on ZnO promotes effective separation and increases the redox power of the photogenerated excitons via the built-in internal electric field of S-scheme pathways between g-C3N4 and ZnO. The successful construction of the S-scheme heterojunction was substantiated through X-ray photoelectron spectroscopy, experimental calculations, radical trapping experiment, and liquid electron spin resonance (ESR) characterization, whereas the existence of OVs was well confirmed by ESR analysis. Meanwhile, the PPy served as a supporter, and the polaron and bipolaron species of PPy acted as electron and hole acceptors, respectively, which further enhances the charge-carrier transmission and separation in the ternary GPZ photocatalyst. The photocatalytic activity of the PPy-designed ternary photocatalyst g-C3N4/PPy/ZnO is outstanding and is greater than that of other samples like g-C3N4, ZnO, and ZnO/g-C3N4 and remove 99.0% of RhB (50 mg/L) in 60 min. RhB could be degraded most effectively by GPZ-0.75 photocatalysis at a pH of 7, and 1.0 g/L of the photocatalyst was the ideal concentration. Gram-positive (G + ve) and Gram-negative (G-ve) microorganisms were used as test subjects to determine the antibacterial effectiveness of the photocatalysts using the good diffusion approach. Ternary g-C3N4/PPy/ZnO heterostructure outperformed its competitors in terms of antibacterial activity. Additionally, after five cycles, the as-synthesized photocatalyst showed superb stability. By using a photocatalyst with a superior utilization efficiency of visible light energy, this paper offers a clearly promising, highly effective, and simple method to destroy exceedingly harmful and renowned contaminants.

Maize (Zea mays L.) planted at higher density utilizes dynamic light more efficiently.

In nature, plants are exposed to a dynamic light environment. Fluctuations in light decreased the photosynthetic light utilization efficiency (PLUE) of leaves, and much more severely in C4 species than in C3 species. However, little is known about the plasticity of PLUE under dynamic light in C4 species. Present study focused on the influence of planting density to the photosynthesis under dynamic light in maize (Zea mays L.), a most important C4 crop. In addition, the molecular mechanism behind photosynthetic adaptation to planting density were also explored by quantitative proteomics analysis. Results revealed that as planting density increases, maize leaves receive less light that fluctuates more. The maize planted at high density (HD) improved the PLUE under dynamic light, especially in the middle and later growth stages. Quantitative proteomics analysis showed that the transfer of nitrogen from Rubisco to RuBP regeneration and C4 pathway related enzymes contributes to the photosynthetic adaptation to lower and more fluctuating light environment in HD maize. This study provides potential ways to further improve the light energy utilization efficiency of maize in HD.

Row ratio increasing improved light distribution, photosynthetic characteristics, and yield of peanut in the maize and peanut strip intercropping system.

Changes in the canopy microclimate in intercropping systems, particularly in the light environment, have important effects on the physiological characteristics of photosynthesis and yield of crops. Although different row ratio configurations and strip widths of dwarf crops in intercropping systems have important effects on canopy microclimate, little information is available on the effects of intercropping on chlorophyll synthesis and photosynthetic physiological properties of dwarf crops. A 2-year field experiment was conducted in 2019 and 2020, with five treatments: sole maize (SM), sole peanut (SP), four rows of maize intercropping with eight rows of peanut (M4P8), four rows of maize intercropping with four rows of peanut (M4P4), and four rows of maize intercropping with two rows of peanut (M4P2). The results showed that the light transmittance [photosynthetically active radiation (PAR)], photosynthetic rate (Pn), transpiration rate (Tr), and stomatal conductance (Gs) of intercropped peanut canopy were reduced, while the intercellular carbon dioxide concentration (Ci) was increased, compared with SP. In particular, the M4P8 pattern Pn (2-year mean) was reduced by 5.68%, 5.33%, and 5.30%; Tr was reduced by 7.41%, 5.45%, and 5.95%; and Gs was reduced by 8.20%, 6.88%, and 6.46%; and Ci increased by 11.95%, 8.06%, and 9.61% compared to SP, at the flowering needle stage, pod stage, and maturity, respectively. M4P8 improves the content of chlorophyll synthesis precursor and conversion efficiency, which promotes the utilization efficiency of light energy. However, it was significantly reduced in M4P2 and M4P4 treatment. The dry matter accumulation and pod yield of peanut in M4P8 treatment decreased, but the proportion of dry matter distribution in the late growth period was more transferred to pods. The full pod number decreases as the peanut row ratio decreases and increases with year, but there is no significant difference between years. M4P8 has the highest yield and land use efficiency and can be used as a reference row ratio configuration for maize-peanut intercropping to obtain relatively high yield benefits.

Construction of Double S‐Scheme ZIF‐67@GDY/CuI Heterojunction by Graphdiyne (g‐CnH2n−2) Nanosheets‐Coated ZIF‐67 on Synergized Charge Transfer for Enhanced Photocatalytic Hydrogen Evolution

Graphdiyne (GDY) is a carbon allotrope material composed of sp and sp2 hybrid carbon atoms, which has been proven to be a good carrier for anchoring metal catalysts due to its abundant alkyne bonds. Herein, a double S‐scheme ZIF‐67@GDY/CuI heterojunction with graphdiyne (g‐CnH2n−2) nanosheets‐coated ZIF‐67 is prepared by a simple mixing method. The ZIF‐67 dodecahedron coated with GDY nanosheets constructed S‐scheme heterojunction by matching valence and conduction bands. The double S‐scheme heterojunction can maintain the strong redox ability of photogenerated electron–hole pairs well and promote more efficient charge transport. The excellent charge transport path is also attributed to the unique double S‐scheme heterojunction, which is confirmed by in situ X‐ray photoelectron spectroscopy. Moreover, the electron migration from ZIF‐67 to GDY generates an internal electric field (IEF), which improves the light energy utilization and charges separation efficiency under the condition of the IEF, band edge bending, and coulomb interaction. The optimal hydrogen production rate of ZIF‐67@GDY/CuI‐20 is 7.27 mmol g−1 h−1 under visible light irradiation, which is significantly increased by 4.75 times compared with the unmodified ZIF‐67. Herein, a new possibility for the construction of double S‐scheme heterojunction based on graphdiyne to improve photocatalytic performance is provided.

Responses of the photosynthetic characteristics of summer maize to shading stress

AbstractThe vast majority of the energy and substance required for maize growth and development and related metabolic processes come from the photosynthesis of leaves. Over the past 60 years, the amount of solar radiation reaching the earth's surface has decreased significantly, reducing the photosynthetic rate of crops and leading to a significant reduction in yields. However, (1) the effects of shading stress on stomatal characteristics, electron transport efficiency of summer maize leaves and (2) the adaptability of summer maize to low light are still unclear. In order to investigate this problems, maize hybrid Denghai605 (DH605) was used as the experimental materials, and two treatments of shading (shading degree is 60%) and CK (natural light as control) were set in the field. The results showed that shading stress resulted in chloroplast dysplasia, and the overall performance of the two photosystems was reduced by 27.85%. The number of stomata per unit area decreased by 15.6% and the proportion of stomatal opening decreased by 73.1% after shading, which resulted in a significant 27.7% reduction in intercellular CO2 concentration. Shading significantly reduced photosynthetic rate by affecting stomatal characteristics and electron transport, and the former was the main influencing factor. The decrease in carbon assimilation capacity resulted in insufficient assimilate supply and significantly reduced grain allocation ratio, resulting in a significant yield reduction of 57.5%. However, in the low‐light environment, the expression of chlorophyll‐binding protein in the leaf of summer maize was upregulated, the content of Lhcb1 protein of the light harvesting pigment protein complex II (LHCII) was increased, and the content of photosynthetic pigment, especially chlorophyll b, was increased, which increased the absorption and capture of blue light, improved the efficiency of light energy utilization, and was a stress manifestation of summer maize adapting to shading stress.

Visible-Light-Driven Enhanced Biohydrogen Production by Photo-Biohybrid System Based on Photoelectron Transfer between Intracellular Photosensitizer Gold Nanoparticles and Clostridium butyricum

Biohydrogen is a clean and renewable energy, but the low yield caused by the lack of reducing power in cells greatly restricts the industrialization of biohydrogen production. Photo-biohybrid systems (PBSs) can integrate the high light energy utilization efficiency of photocatalysts with the excellent catalytic performance of microorganisms. Here, gold nanoparticles were targeted into Clostridium butyricum as intracellular photosensitizers to construct a PBS that could efficiently produce biohydrogen under visible light, with the apparent quantum yield as high as 19.31%. Compared with the dark-fermented C. butyricum, the biohydrogen production of PBS increased by 88.74%. The mechanism of photoelectrons from Au NPs to C. butyricum was elucidated by the transcriptome. Compared with the dark-fermented biohybrids, the expressions of biohydrogen generation-related enzymes, such as hydrogenase and pyruvate formate lyase genes, in the PBS were all upregulated more than 2 times. Furthermore, the genes of riboflavin synthase, electron transfer flavoprotein (ETF), and FAD-dependent oxidoreductase, which are closely related to electron transformation, were all significantly upregulated. The photoelectrons were transferred to the hydrogenase via ETF and FAD2+ to enhance biohydrogen production, independent of pyruvate decomposition. This PBS provides theoretical guidance for constructing an efficient light-driven microbial manufacturing system.

Molten salt-assisted synthesis of nitrogen-vacancy crystalline graphitic carbon nitride with tunable band structures for efficient photocatalytic overall water splitting

The photocatalytic overall water splitting performance of graphitic carbon nitride (g-C3N4) has still been restricted by its inefficient charge separation efficiency. Herein, nitrogen-vacancy crystalline g-C3N4 nanosheets (g-C3N4-D) with tunable band structures were successfully prepared by the alkali-molten salt-assisted method for efficient photocatalytic overall water splitting. Among them, g-C3N4-D2 not only combines the advantages of the amorphous and crystalline state of two-dimensional g-C3N4 nanosheets, but also introduces nitrogen vacancy to adjust the bandgap structures of crystalline g-C3N4 by an alkali etching, thus improving the light energy utilization and charge separation efficiency. TEM and EPR spectrum prove the existence of N defects in the crystalline g-C3N4. The excellent and stable photocatalytic overall water splitting activity with H2 and O2 evolution rate of 49.60 μmol g−1 h−1 and 24.71 μmol g−1 h−1 was obtained over g-C3N4-D2 with Pt and Co3O4 nanorods as cocatalysts (Pt/g-C3N4-D2/3%Co3O4 NRs) under AM 1.5G simulated light irradiation. In the half-reaction experiments, the maximum H2 evolution rate of Pt/g-C3N4-D2/3%Co3O4 NRs is 3.78 mmol g−1 h−1 with a significant quantum efficiency of 11.94 % at 400 nm, and the solar-hydrogen conversion efficiency (STH) is 1.48 %. The photocatalytic water oxidation activity of Pt/g-C3N4-D2/5%Co3O4 NRs is 42.34 μmol g−1 h−1. Additionally, the potential mechanism of photocatalytic overall water splitting was testified by in-situ XPS. This work provides a simple strategy for further advancing the potential application of g-C3N4 by molten salt-assisted alkali etching to introduce N vacancies to regulate the band gap of crystalline g-C3N4 for photocatalytic overall water splitting.