Use Of Pressure-sensitive Film Research Articles

Occlusal status of implant superstructures at mandibular first molar immediately after setting.

BackgroundOcclusal contact on the implant superstructures is important for successful treatment. The purpose of this study was to investigate the occlusal contact of single implant superstructures at the mandibular first molar immediately after seating from weak to strong clenching.MethodsSubjects were nine patients who had just been fitted with an implant prosthesis in the mandibular first molar region, with no missing teeth other than in the implant region. First, while masseter muscle activity was monitored, maximum clenching strength (100 % maximum voluntary contraction (MVC)) was determined with an electromyogram. Next, occlusal load and occlusal contact area were measured three times at clenching intensities of 40, 60, 80, and 100 % MVC by the use of pressure-sensitive film for occlusal force diagnostic and Occluzer for occlusal force measurement. Finally, the occlusal contact area was measured once each at 20, 40, and 60 % MVC using a silicone testing material and BiteEye for occlusal contact measurement. A two-way analysis of variance (ANOVA) was used to determine occlusal loading and occlusal area as dependent variables, and clenching strength and presence or absence of implant as between-subject factors. A multiple comparison test was performed using the Bonferroni method.ResultsThe occlusal contact area and occlusal load of the implant prosthesis increased with clenching strength, and the increases in occlusal contact area and occlusal load of the implant prosthesis were less than those of the contralateral tooth at high clenching strength. However, significant difference was not observed when compared with both sides of the molar region regardless of clenching strength.ConclusionsThe occlusal contact area of the implant had a tendency to be adjusted smaller than the natural tooth by a dental technician and a dentist. On the other hand, despite the small tissue displaceability of the implant, occlusal load on the implant prosthesis was smaller than on the natural tooth at high clenching strength.

Misalignment of Total Ankle Components Can Induce High Joint Contact Pressures

A major cause of the limited longevity of total ankle replacements is premature polyethylene component wear, which can be induced by high joint contact pressures. We implemented a computational model to parametrically explore the hypothesis that intercomponent positioning deviating from the manufacturer's recommendations can result in pressure distributions that may predispose to wear of the polyethylene insert. We also investigated the hypothesis that a modern mobile-bearing design may be able to better compensate for imposed misalignments compared with an early two-component design. Two finite element models of total ankle replacement prostheses were built to quantify peak and average contact pressures on the polyethylene insert surfaces. Models were validated by biomechanical testing of the two implant designs with use of pressure-sensitive film. The validated models were configured to replicate three potential misalignments with the most version of the tibial component, version of the talar component, and relative component rotation of the two-component design. The misalignments were simulated with use of the computer model with physiologically relevant boundary loads. With use of the manufacturer's guidelines for positioning of the two-component design, the predicted average joint contact pressures exceeded the yield stress of polyethylene (18 to 20 MPa). Pressure magnitudes increased as implant alignment was systematically deviated from this reference position. The three-component design showed lower-magnitude contact pressures in the standard position (<10 MPa) and was generally less sensitive to misalignment. Both implant systems were sensitive to version misalignment. In the tested implants, a highly congruent mobile-bearing total ankle replacement design yields more evenly distributed and lower-magnitude joint contact pressures than a less congruent design. Although the mobile-bearing implant reduced susceptibility to aberrant joint contact characteristics that were induced by misalignment, predicted average contact stresses reached the yield stress of polyethylene for imposed version misalignments of >5 degrees.

High inter-specimen variability of baseline data for the tibio-talar contact area

Background The tibio-talar contact area has been widely investigated to monitor biomechanical changes due to articular incongruities or an altered loading. This study aims to investigate for the first time in a systematic way the extent of the inter-specimen variability of the tibio-talar contact area, and its repercussions when analyzing data concerning this parameter. Methods Ten specimens were loaded to record the tibio-talar contact characteristics by use of pressure sensitive film. The size of the talar dome area, the size of the (normalized) tibio-talar contact area, the position of the tibio-talar contact area, and the shape of the latter were determined and analyzed. Inter-specimen variability was expressed as the coefficient of variation and was calculated for the datasets of previous studies as well. Findings The size of the tibio-talar contact area showed a very high inter-specimen variability, as is the case in previous studies. This high variability persisted when a normalized tibio-talar contact area was calculated. The shape of the tibio-talar contact area showed some basic characteristics, but a high variation in details could be observed. Interpretation Every specimen can be considered to have its own “ankle print”. By this variability, articular incongruities are expected to have a different effect on local biomechanical characteristics in every single individual. Therefore, every single case has to be evaluated and reported for significant changes. In case of modeling, this also underscores the need to use subject specific models fed by sets of parameters derived from a series of single specimens.

Mechanical Testing of Seven Fixation Methods for Generation of Compression Across a Midtarsal Osteotomy: A Comparison of Internal and External Fixation Devices

The purpose of this study was to assess 7 methods of fixation for a midtarsal osteotomy. Polyurethane foam models (N = 6) and cadaver specimens (N = 4-7) were used to examine the force generated by the different constructs of fixation. A midtarsal osteotomy was performed on each specimen in the test groups. The osteotomies were fixated either with 2 parallel 0.062-in Kirschner wires and 40-mm-long, 4-mm partially threaded, cancellous, cannulated titanium screws, an external ring fixator (frame), a frame with wires tensioned (tension), a frame with wires tensioned and compressed toward the osteotomy (tension and compression), a frame with tension, compression, and parallel Kirschner wires, or a frame with tension, compression, and two 4.0 cannulated parallel screws, respectively. Each model was fixated, and the force generated by the construct across the osteotomy was recorded via the use of pressure-sensitive film. Statistical analysis of the data in the polyurethane foam group determined that the use of frame with tension, compression, and two 4.0 parallel cannulated screws was statistically superior to 1) frame, 2) frame with tension, 3) 2 parallel Kirschner wires, 4) two 4.0 cannulated parallel screws, and 5) frame with tension and compression. A cadaver study determined that the frame with tension, compression, and 2 parallel Kirschner wires was statistically superior to 1) frame and 2) two parallel Kirschner wires. These findings suggest that there is a difference in the force generated by the type of fixation construct across a midtarsal osteotomy.

Contact mechanics of normal tarsometatarsal joints.

The current treatment of tarsometatarsal joint injuries is associated with suboptimal long-term results. The objective of the present study was to measure the contact mechanics of the tarsometatarsal joints in normal adult cadaveric feet in order to develop a foundation for more effective treatment. Six fresh cadaveric lower legs and feet were subjected to four different axial compressive loads (0.5, 1.0, 1.5, and 2.0 times body weight) at each of five different positions. For each position, load, and tarsometatarsal joint, the contact pressures and areas were measured with use of pressure-sensitive film. Contact forces were calculated from the ratio of pressure to area. Contact pressure, area, and force were analyzed as a function of load, the specific tarsometatarsal joint, and foot position. The forces across these joints ranged from 2 to 541 N, but pressures ranged only from 0.5 to 5.7 MPa. In general, changes in load and foot position, in both the sagittal and the frontal plane, were associated with changes (p<0.05) in tarsometatarsal joint contact areas and forces. In contrast, the contact pressures across these joints varied minimally with changes in load and foot position. These data suggest that the tarsometatarsal joints are designed to regulate pressure in each joint by means of two mechanisms: (1) at small loads, an intrajoint mechanism regulates tarsometatarsal joint pressure by increasing contact area within the joint in response to increasing force, and (2) at larger loads, an interjoint mechanism engages to regulate tarsometatarsal joint pressure by redirecting force to other tarsometatarsal joints. The data provide both absolute (normal contact forces, areas, and pressures) and relative (intrajoint and interjoint regulating mechanisms) performance (functional) criteria for the development of new treatments for diseased or traumatized tarsometatarsal joints.

The role of the acetabular labrum and the transverse acetabular ligament in load transmission in the hip.

We performed a biomechanical study of seventeen hip joints in the pelves of nine cadavera in order to assess the role that the acetabular labrum and the transverse acetabular ligament play in load transmission. The distribution of contact area and pressure between the acetabulum and the femoral head was measured with the hip in four different conditions: intact (seventeen hips), after removal of the transverse acetabular ligament (eight hips), after removal of the entire labrum (nine hips), and after removal of both the transverse acetabular ligament and the labrum (seventeen hips). The hip joint was loaded in simulated single-limb stance, and the measurements were made with use of pressure-sensitive film. A peripheral distribution of load was seen in the intact acetabula. This pattern was altered only minimally after removal of the transverse acetabular ligament or the labrum, or both. When both of these structures were removed, the only significant change was a decrease in the maximum pressure in the posterior aspect of the acetabulum (p = 0.02). No significant changes were detected with regard to the contact area, load, mean pressure, or maximum pressure in the anterior or superior aspect of the acetabulum under any testing condition.

Effects of partial patellectomy and reattachment of the patellar tendon on patellofemoral contact areas and pressures.

We used a previously reported experimental method to measure patellofemoral contact areas and pressures in four pairs of human cadaveric knees before and after a partial patellectomy. The knee joints were loaded by application of a flexion moment, which was resisted by the extension moment of the quadriceps mechanism. Patellofemoral contact was measured with the use of pressure-sensitive film, at 30, 60, and 90 degrees of flexion of the knee. Partial patellectomy decreased the patellofemoral contact area and increased pressure. We observed alterations in the patterns of contact, including a proximal shift in patellofemoral contact, after partial patellectomy. An anterior reattachment of the patellar tendon significantly minimized the effects of 20 and 40 per cent patellectomies (p < 0.05). After a 60 per cent patellectomy, patellofemoral contact was altered markedly, with the contact area reduced to less than 50 per cent of the control values regardless of the position of the patellar tendon reattachment.

A comparison of scaphoid-trapezium-trapezoid fusion and four-bone tendon weave for scapholunate dissociation

The contact characteristics of the radiocarpal joint (area, pressure, and ratios of scapholunate area, pressure and force transmitted) were determined with the use of pressure-sensitive film in seven normal wrists after ligament sectioning to create scapholunate instability, with reconstruction involving a scaphoid-trapezium-trapezoid fusion, and with reconstruction involving a fourbone tendon weave procedure. The results demonstrated that the scaphoid-trapezium-trapezoid fusion significantly altered the contact characteristics of the wrist, transferring load, pressure, and area to the radioscaphoid joint, thereby unloading the lunate. In contrast, the tendon weave reconstruction produced characteristics similar to those of the normal join

The effect of simulated fracture-angulations of the tibia on cartilage pressures in the knee joint.

The effects of angular deformities of the tibia on the contact areas and pressures on cartilage in the knee were measured with use of pressure-sensitive film. Six cadaver knees were mounted in a test-frame, such that the offset and tilt of the knee relative to the load-axis simulated that due to angular deformities of the tibia of 5, 10, 15, or 20 degrees of varus or valgus at the levels of the proximal, middle, and distal thirds. Angulation had little effect on the contact area. The change in pressure was least for fractures of the distal third and greatest for fractures of the proximal third. For example, a 20-degree angulation of the distal third increased the maximum contact pressure by an average of 26 per cent in the compartment toward the load-axis and reduced it by 32 per cent in the opposite compartment. With an angulation of 20 degrees at the level of the proximal third of the tibia, the increase in pressure averaged 106 per cent and the decrease averaged 89 per cent. The changes in pressure with fractures at the middle third were between these extremes.