Upper Surface Research Articles

Understanding and Strategies for High Energy Density Lithium‐Ion/Lithium Metal Hybrid Batteries

AbstractA pressing need for high‐capacity anode materials beyond graphite is evident, aiming to enhance the energy density of Li‐ion batteries (LIBs). A Li‐ion/Li metal hybrid anode holds remarkable potential for high energy density through additional Li plating, while benefiting from graphite's stable intercalation chemistry. However, limited comprehension of the hybrid anode has led to improper utilization of both chemistries, causing their degradation. Herein, this study reports an effective hybrid anode design considering material properties, the ratio of intercalation‐to‐plating capacity, and Li‐ion transport phenomena on the surface. Mesocarbon microbeads (MCMB) possesses desirable properties for additional Li plating based on its spherical shape, lithiophilic functional group, and sufficient interparticle space, alongside stable intercalation‐based storage capability. Balancing the ratio of intercalation‐to‐plating capacity is also crucial, as excessive Li plating occurs on the top surface of the anode, eventually deactivating the intercalation chemistry by obstructing upper pores. To address this issue, electrospun polyvinylidene fluoride (PVDF) is introduced to prevent Li metal accumulation on the upper surface, leveraging its non‐conductive, polar nature, and high dielectric constant. By implementing these strategies, a LiNi0.8Co0.15Al0.05O2 (NCA)‐paired pouch cell delivers an outstanding energy density of 1101.0 Wh L−1, highlighting its potential as an advanced post‐LIBs with practical feasibility.

Aspidistra shangsiensis (Asparagaceae), a new species from Guangxi, China

Aspidistra shangsiensis, a new species of Asparagaceae from southern Guangxi, China, is described and illustrated. The new species is similar to A. hainanensis in the flower color and shape, but differs by the leaf blade narrowly lanceolate, 28–45 × 4.0–6.5 cm, perianth lobes 8–10, stigma upper surface with fine radial grooves distally. This new species is only known from Shangsi County in Guangxi, China.

Effectiveness of external prestressing in enhancing the non-ductile hanger failure mechanism in reinforced concrete inverted T-beams

Recently, inverted T-beams have been used in reinforced concrete (RC) bridges to support transverse precast stringers. Inverted T-beams, contrary to practice with conventional beams, are loaded on the flanges upper surface. This loading configuration causes hanger failure due to the generation of vertical tensile stresses near the bottom of the web. The key purpose of this study is to investigate the efficiency of vertical external prestressing stainless-steel bars in mitigating non-ductile hanger failure in reinforced concrete inverted T-beams. An experimental study on six inverted-T beams, including two un-strengthened specimens, was carried out. The study showed that the value of the prestressing level had a considerable impact on the performance of hanger mechanism in relation to crack pattern, ultimate loads, cracking behavior, load–deflection, strains, and ductility. The experimental results indicated that the suggested method for strengthening inverted T-beams had efficacy in reducing the seriousness of the non-ductile hanger failure and resulted in a strength increase of up to 53% when compared to that of the un-strengthened specimen. Additionally, two analytical models for estimating the hanger capacity and the average crack width of the strengthened RC inverted T-beams were proposed. The models that were proposed exhibited a high degree of agreement with the experimental results.

Powder movement rules of laser powder bed fusion additive manufacturing aluminum alloy based on discrete element method

Laser Powder Bed Fusion (LPBF) is a promising metal additive manufacturing technology based on layer by layer powder spreading, and powder bed uniformity has a great influence on the forming quality. By Discrete Element Method and powder spreading experiment, the interaction and movement between powder were studied during powder spreading, including powder jamming, rebound, splash, eddy, and empty powder area. Additionally, five kinds of powder spreading schemes were explored, and the new process of one-way reciprocating with tri-splint blade was designed to change the motion state of powder spreading from “blade pushing powder” to “blade holding powder.” By increasing the distance between the blade and the working platform form 0 to 20 µm with the distance between the upper surface of the substrate and the working platform 50 µm, defects such as powder splash and empty powder decreased. And the uniform powder bed of aluminum alloy powder was achieved with the new process of one-way reciprocating with tri-splint blade structure.

Полосковый резонатор СВЧ с объемным кристаллом: экспериментальные характеристики и определение эффективной диэлектрической проницаемости

The paper presents the results of an experimental study and modeling of the frequency characteristics of a resonator in the form of two strip vibrators, separated by a large gap and covered with a bulk lithium niobate crystal. A metal electrode with a floating potential is installed on the upper surface of the crystal. The frequency dependences of the scattering matrix coefficients of a stripline resonator were measured in the frequency range up to 3 GHz. Electrodynamic analysis was carried out in the COMSOL Multiphysics numerical simulation environment. A comparison was made of experimental and numerical results, which showed good qualitative agreement between the transmission coefficients and reflection coefficients. Resonant oscillations were obtained at two or three frequencies depending on the location and orientation of the crystal. It has been established that at the first resonant frequency the electrode acts as a screen. The absence of an electrode leads to the disappearance of resonance. The simulation carried out in COMSOL made it possible to estimate the effective dielectric constant of the resonator corresponding to the values of the resonant frequencies. The calculation of electromagnetic fields made it possible to establish the types of waves corresponding to resonant frequencies. Knowing the type of waves and estimating the relative dielectric constant made it possible to construct an algorithm for a refined iterative procedure for calculating the values of the resonant frequencies and the effective dielectric constant of the resonator. The possibility of using resonators as single-link bandpass filters with a passband of about 1%, insertion loss of –1.1 dB and minimal return loss of –28 dB at the center frequency is shown.

The effect of photoinitiator type and filler load on physicochemical and mechanical properties of experimental light-cured resin cements through lithium disilicate ceramics of different shades and thicknesses

ObjectiveThis study investigated the influence of photoinitiator types on degree of conversion (DC), rate of polymerization (RP), flexural strength (FS), flexural modulus (FM), and light transmittance (LT) of filled and unfilled light-curable resin cements through different thicknesses and shades of lithium disilicate ceramics. MethodsLithium disilicate ceramic discs (IPS Emax Press, background [0.0], 0.5, 1.0, 2.0, 3.0, and 4.0 mm, shades A1 and BL3) were prepared. Experimental resin-based cements [TEGDMA/BisGMA (50/50 mass%)] were prepared using either camphorquinone (CQ)/amine (0.44/1.85 mol%) or TPO (0.44 mol%)], and a micro and nanofiller loads of nil (unfilled); 40/10 mass%; and 50/10 mass%). Resin cements (0.2 mm thick) were placed on the lower surface of the ceramic specimens and light-activated for 30 s from the upper surface using a Bluephase Style curing light (exitance at tip: 1236 mW/cm2 ± 1.20). LT and distribution of irradiance through the ceramics were measured using a UV–vis spectrometer and a beam profile camera, respectively (n = 3). The DC and RP were measured in real-time using mid infrared spectroscopy in attenuated total reflectance (ATR) mode (n = 3). FS and FM were measured using a universal testing machine (n = 5). Statistical analyses were performed on LT, DC, RP, FS, and FM data using a general linear model, and supplementary ANOVA and post hoc Tukey multiple comparison test were also performed (α = .05). ResultsThicknesses, shades, photoinitiator type, and fillers load significantly influenced the optical and mechanical characteristics of the resin-based materials (p < 0.05). The BL3 shade ceramic provided higher values of DC, RP, FS, FM, and LT compared with the A1 shade (p < 0.05). Increasing ceramic thickness decreased the properties of the resin-based materials (p < 0.05). Generally, TPO improved mechanical properties of the resin cement compared with CQ (p < 0.05). SignificanceThe luting process of indirect restorations may be improved by using high molar absorptivity, more reactive, and more efficient photoinitiators such as TPO, as opposed to conventional CQ. The use of such initiator may allow the placement of thicker and more opaque indirect restorations.

Chemical polishing strategies to improve flexible perovskite solar cells based on dopant-free hole transport layers

For n-i-p typed flexible perovskite solar cells (fPSCs), the doped hole transport layer significantly impacts the devices' long-term stability. Using dopant-free organic hole transport materials (d-HTMs) is promising for stable fPSCs. However, the low conductivity of d-HTMs limited their thickness, making them sensitive to the surface morphology of the perovskite film's upper surface. Here, we report a chemical polishing strategy using 1-hexyl-3-methylimidazolium acetate (HMIM∙Ac) as the polishing reagent to enhance the upper surface of the perovskite film, which could form a smooth and flat surface. Meanwhile, the treatment can reduce surface defects and smaller grains on top of the surface. Then, we deposite an ultra-thin dopant-free PM6 layer, a typical hole transport layer, on top of the polished perovskite film. The PM6 layer shows an improved face-on orientation and then carrier mobility. Moreover, suppressed non-radiative recombination at the perovskite/PM6 interface is also observed, translating into a higher open-circuit voltage and fill factor of the fPSCs. As a result, a champion power conversion efficiency (PCE) of 17.76 ​%, with an open-circuit voltage of 1.025 ​V and fill factor of 78.2 ​%, is obtained, which is one of the highest PCEs among the reported fPSCs based on d-HTMs. Our strategy demonstrates a facile but effective way of developing high-efficiency and stable fPSCs for future applications.

Visualization experimental study on evaporation heat transfer characteristics of an open evaporator with a tower-like porous wick

Temperature overshoot often occurs in loop heat pipe, which is caused by the large bubble in the compensation chamber. But it is still uncertain whether this large bubble grew from parasitic bubbles inside porous wick. A multi-layer tower-like porous wick is designed to understand the growth and expansion of parasitic bubbles. The parasitic bubbles are induced to occur inside porous wick by inserting a copper pillar on the evaporator wall, and the multi-layer porous wick is used to eliminate parasitic bubbles. The pumping stagnation occurs under certain heat loads, but temperature overshoot of the evaporator wall no longer occurs in the open evaporator with the tower-like porous wick, which guides the design of evaporator to avoid temperature overshoot. It is found that a lot of small bubbles only appears on the lower surface of porous wick immersed in liquid in the evaporator, while not appears on the upper surface. Three groups of repeated experiments are carried out sequentially and the performance of the evaporation heat transfer gradually deteriorates, which is speculated to be caused by a gap between porous wick and the copper pillar, larger pore size next to copper pillar, or poor wetting caused by copper pillar oxidation. Two different types of the evaporator overheating are discovered, including the overall retreat of the evaporating interface and dry-out region expanded from the internal of porous wick to the external. At high heat load, the evaporating interface expands along the copper pillar, causing an increase in the heat transfer coefficient of the evaporator. The research results indicate that in order to better utilize porous wick for evaporation heat transfer, it is necessary to reliably adhere porous wick to the heating surface and avoid the formation of the large bubble in the compensation chamber.

The Determination of Minerals in Soil, Water, Fodder, and Serum and their Effects on Reproductive Efficiency of Nili Ravi Buffaloes

Introduction: Minerals play an essential role in the reproductive performance of dairy animals, especially in buffaloes. The present study aimed to evaluate the mineral concentrations in different types of samples, including soil used for fodder cultivation, canal water used for fodder irrigation, drinking water for buffaloes, fodder used for buffalo feeding, and serum of buffaloes and their effects on the reproductive efficiency of buffaloes. Materials and methods: The current study was carried out for three months and samples were analyzed twice at the beginning and the end of the study. The concentrations of calcium, magnesium, and inorganic phosphorus in the soil were checked through the versinate method. The concentration of calcium, magnesium, and inorganic phosphorus in water was checked through the titration method and the concentration of calcium, magnesium, and inorganic phosphorus contents in fodder was checked through the wet digestion method. The minerals of blood serum (n = 80) were analyzed through commercial kits. Results: In canal water, calcium concentration was higher for irrigation compared to buffalo drinking water. Similarly, on the upper surface of the soil compared to its low surface, the level of calcium was high. Calcium values of serum were higher in cyclic buffaloes compared to buffalo heifers. In comparison to all groups, the levels of inorganic phosphorus were found to be lower in non-cyclic buffaloes. Similarly, the calcium-to-phosphorus ratio was found to be lower in non-cyclic buffaloes and heifers compared to repeat breeders and cyclic buffaloes. At the beginning of the study, cyclic buffaloes had higher magnesium levels than all other groups, except for non-cyclic buffaloes. By the end of the study, magnesium concentrations were higher in non-cyclic buffaloes and heifers compared to repeat breeders and cyclic buffaloes. Conclusion: The mineral deficiencies in water and soil can affect the fodder content in the feed of buffaloes.

Elastic discrete element analysis of natural vibration characteristics and settlement behavior of railway ballasted track

An elastic multi-body model of a ballasted track, consisting of an aggregate of ballast gravel and a single prestressed mono-block concrete sleeper, is constructed. Field-measured traffic load waveforms from an operational existing railway track are then applied to the left and right rail positions on the upper surface of the model using elastic discrete element method. The numerical results are subjected to frequency analysis to examine the relation between track settlement and natural vibration phenomena in ballasted tracks. The relative error between the measured and analyzed frequency values for the natural vibration modes of the ballasted track under 500 Hz is 2.23%, indicating that the current ballasted track model accurately reproduces the natural vibration characteristics of existing ballasted track structures. The analysis results reveal that the phenomenon of plastic deformation within the ballast layer occurs primarily in the upper part of the ballast layer, just below the sleeper. Additionally, for the bounce mode of the ballast layer in the frequency range of generally 100 Hz and below, it has been identified as the primary factor promoting significant vertical motion of the sleeper, along with the associated reverse U-shaped deformation of the sleeper, which accelerates the track structure degradation. Furthermore, when loosening occurs, the vibrational energy of this bounce mode increases, contributing directly to ballast degradation.

Synergetic Optimization of Upper and Lower Surfaces of the SnO2 Electron Transport Layer for High-Performance n-i-p Perovskite Solar Cells.

The SnO2 electron transport layer (ETL) has been recognized as one of the most effective protocols for achieving high-efficiency perovskite solar cells (PSCs). To date, most research has primarily focused on the modification of the upper surface of SnO2 ETL films. The lower surface of the SnO2 film, which directly influences the film formation of solution-processed SnO2, is equally important but receives relatively less attention. Herein, we present a synergetic optimization approach involving the deposition of aluminum oxide (AlOx) via atomic layer deposition (ALD) as a buffer layer and the incorporation of rubidium acetate (RbAc) as an upper surface passivation additive. This process leads to a conformal coating of SnO2 nanoparticles, improved electrical performance, and higher-quality perovskite crystals. As a result, with this composite ETL film, the power conversion efficiency (PCE) reached 22.41 from 20.77%. Further modification with p-butyl iodide (BAI) on the perovskite upper surface increased the champion PCE to 23.32%, with a voltage loss of 0.41 V, ranking among the lowest values for the triple-cation mixed-halide perovskite absorber (1.58 eV). Importantly, the perovskite solar cells remained 87.30% of its initial performance after 14 days of aging and exhibited photostability under long-term UV (254 nm) illumination.

Hepatic grooves: An observational study at laparoscopic surgery.

In traditional descriptions, the upper surface of the liver is smooth and convex, but deep depressions are variants that are present in 5%-40% of patients. We sought to determine the relationship between surface depressions and the diaphragm. To use exploratory laparoscopy to determine the relationship between surface depressions and the diaphragm. An observational study was performed in all patients undergoing laparoscopic upper gastro-intestinal operations between January 1, 2023 and January 20, 2024. A thirty-degree laparoscope was used to inspect the liver and diaphragm. When surface depressions were present, we recorded patient demographics, presence of diaphragmatic bands, rib protrusions and/or any other source of compression during inspection. Of 394 patients, 343 had normal surface anatomy, and 51 (12.9%) had prominent surface depressions on the liver. There was no significant relationship between the presence of surface depressions and gender nor the presence of rib projections. However, there was significant association between the presence of surface depressions and diaphragmatic muscular bands (P < 0.001). With these data, the diaphragmatic-band theory has gained increased importance over other theories for surface depressions. Further studies are warranted using cross sectional imaging to confirm relationships with intersectional planes as well as beta-catenin assays in the affected liver parenchyma.

Indium Tin Oxide Induced Internal Positive Feedback and Indium Ion Transport in Perovskite Solar Cells.

Stability is the most pressing challenge hindering the commercialization of perovskite solar cells (PSCs), and previous efforts focused more on enhancing the resistance of PSCs to external stimulus. Here, we found that the indium tin oxide (ITO) will deteriorate the photovoltaic performance of PSCs through positive feedback cycles. Specifically, the perovskite degradation products will cross the electron transport layer to chemically etch the electrode ITO to generate In3+, which will migrate upwards into the perovskite film. Then, the reaction that corrodes ITO consumes the decomposition products of perovskite and shifts the balance of the perovskite decomposition reaction, further promoting the degradation and thus falling into a positive feedback cycle. Moreover, the In3+ in the perovskite film was found to accumulate at the upper surface, which would lead to n-type doping of perovskite film to form the energy barrier for interface carrier extraction. Subsequently, the chelating molecule ethylenediaminetetraacetic acid disodium salt (EDTA-2Na) was introduced onto ITO to firmly chelate the In3+ and prevent it from migrating upward, thus breaking this internal positive feedback cycle and significantly enhancing the efficiency and stability of PSCs. This work provides new perspectives for understanding the mechanism of photovoltaic performance loss and ionic transport in PSCs.

Indium Tin Oxide Induced Internal Positive Feedback and Indium Ion Transport in Perovskite Solar Cells

AbstractStability is the most pressing challenge hindering the commercialization of perovskite solar cells (PSCs), and previous efforts focused more on enhancing the resistance of PSCs to external stimulus. Here, we found that the indium tin oxide (ITO) will deteriorate the photovoltaic performance of PSCs through positive feedback cycles. Specifically, the perovskite degradation products will cross the electron transport layer to chemically etch the electrode ITO to generate In3+, which will migrate upwards into the perovskite film. Then, the reaction that corrodes ITO consumes the decomposition products of perovskite and shifts the balance of the perovskite decomposition reaction, further promoting the degradation and thus falling into a positive feedback cycle. Moreover, the In3+ in the perovskite film was found to accumulate at the upper surface, which would lead to n‐type doping of perovskite film to form the energy barrier for interface carrier extraction. Subsequently, the chelating molecule ethylenediaminetetraacetic acid disodium salt (EDTA‐2Na) was introduced onto ITO to firmly chelate the In3+ and prevent it from migrating upward, thus breaking this internal positive feedback cycle and significantly enhancing the efficiency and stability of PSCs. This work provides new perspectives for understanding the mechanism of photovoltaic performance loss and ionic transport in PSCs.

Impact of low-temperature and low-pressure mild oxidation after plasma solidification on electrical properties and reliability in ultra-thin SiON MOSFETs

The impact of different SiON manufacturing processes on performance and reliability behaviors has been investigated for the MOSFETs. The performance of devices composed of an ultrathin SiON film fabricated by the novel low-temperature and low-pressure mild oxidation after the plasma solidification (LLMOPS) method can be enhanced compared to conventional processes, which is attributed to the increased mobility. It is observed from secondary ion mass spectrometry analysis that the distribution of nitrogen with the LLMOPS process moves toward the upper surface of SiON. As a result, the p-MOSFET manufactured by the LLMOPS process exhibits lower electrical performance degradation during the NBTI stress, indicating that a reduction in nitrogen concentration at the Si/SiO2 interface contributes to improving NBTI behavior. It is also demonstrated that the inhibition of NBTI phenomena enhances the frequency stability on the ring oscillator with circuit simulation. Thus, the LLMOPS process is a promising approach to improve the performance and reliability of MOSFETs in mass production.

A study on attenuation patterns of acoustic waves in waveguide structures with flexural boundaries

This research article investigates the attenuation patterns of acoustic waves within waveguide structures featuring flexural boundaries. By employing advanced methods in vibrations and controls, the study aims to enhance our understanding of waveguide behavior and offer valuable insights for optimizing acoustic wave propagation in diverse applications. The entire waveguide structure is tuned through cooperative interactions involving elastic plates, membranes, and rigid boundary surfaces. The lower boundary of the expansion chamber consists of a rigid plate, with elastic membranes covering the upper surfaces of the cavity. The problem is formulated in terms of transmission and reflection coefficients of the modes, enabling the solution of the scattering problem. Matching acoustic pressure and velocity at the waveguide junction yields the scattering coefficients. The results reveal that the scattering coefficients are intricately influenced by both the geometric characteristics of the waveguide and the frequency of the incident waves. Notably, the first higher-order mode of the cut-off frequency of the waveguide structure corresponds to the frequency at which the dissipation coefficient reaches its maximum value. This research provides valuable insights into the scattering behavior of acoustic waves in waveguide configurations, contributing to the design of acoustic devices and systems. Rigorous support and justification for all aspects of the mode-matching method, including pressure and velocity matching, eigen properties, physical edge conditions, convergence criteria, and energy conservation, are provided through thorough algebraic and numerical analyses, confirming the validity of the solution methodology.

The Effect of Vortex Generators on Spray Deposition and Drift from an Agricultural Aircraft

Vortex generators (VGs) attached to the leading edge of an agricultural aircraft are purported to control airflow over the upper surface of the wing by creating small vortices that delay boundary layer separation, thereby improving the performance of the aircraft. These devices are commercially available for use in the aviation industry, primarily to increase pilot control of the aircraft. The benefits attributed to VGs remain largely descriptive and anecdotal in nature without rigorous empirical assessment in the field. The intent of this study was to evaluate whether this aerodynamic device could improve deposition or reduce drift when mounted on an agricultural aircraft. Airborne drift and ground deposition were measured with monofilament lines and Mylar cards, respectively. Deposits were expressed as percent of fluorometric response using a spectrofluorophotometer. There were 46% fewer downwind drift deposits on monofilament lines when VGs were installed than when VGs were not installed. Whether or not VGs were installed on the aircraft was the predominant factor which influenced deposition on monofilament lines. Spray deposits on Mylar cards placed at ground level downwind of the applications at three different locations (5, 10, and 20 m) varied significantly (p &lt; 0.0001) between treatments, with corresponding 31, 54, and 61% reductions in downwind deposits when VGs were installed. While these findings overall are positive, this is the first known study of its type, and more research is warranted to better understand the role of vortex generators in the reduction in drift relative to aerially applied sprays.

Thermal-bioconvection instability in a suspension of phototactic microorganisms heated from below

In this study, we investigate the linear stability of a suspension of motile algae under the combined influence of phototaxis and temperature gradients. The suspension, heated from below and illuminated from above with vertical collimated irradiation, sheds light on the intricate interplay between biological responses and thermal dynamics. The Navier–Stokes equation, thermal energy equation, and cell conservation equation are considered for the mathematical model. In suspension, the upper surface is taken as stress-free, while the lower surface is taken as rigid. The resulting eigenvalue problem, including the bioconvection Rayleigh and thermal Rayleigh numbers, is resolved numerically. Changes in the critical total intensity and Lewis number do not impact the critical threshold of the thermal Rayleigh number; however, they notably influence the critical bioconvection Rayleigh number. The critical total intensity and Lewis number destabilize the suspension. It is observed that heating from below enhances the instability of the layer. At higher temperatures, Rayleigh–Bénard convection dominates bioconvection, resulting in a single convection cell. Neutral curves of linear stability reveal transitions between stationary and oscillatory solutions. The results, validated against established methods, highlight the system’s response to parameters and phenomena such as Hopf bifurcations and limit cycles.

Evidence for active faults along the Sinop trough close to the Mid Black Sea Ridge Using Multi-Channel Seismic and Multi-Beam Bathymetric Data

Abstract Focal mechanism solutions of the earthquakes that occurred in the Black Sea in the last 100 years show that thrust and strike-slip faults are predominantly active in the region. One of these clusters is developing off the coast of Samsun where the submarine Sinop basin is located. In order to investigate the seismic sources of earthquakes in this area, 14 high-resolution multi-channel seismic sections and multi-beam bathymetric data were processed and evaluated. The oldest seismic stratigrafic units (U4) is referred to as coustic basement with wavy reflectors, while its top is marked by high ampitude reflection indicating an unconformity. This uniconformity is overlain by parallel or less parallel Unit 3 deposits. Upper surface of Unit 2 is marked by an erosional surface which is overlain by parallel reflector of Unit 1. Unit 1 is the youngest sediments and truncated by Yeşilırmak canyon. Three fault types of different ages were determined. The oldest fault could reach only top of unit 4 has been interpreted as inactive fault. Faults that border the Sinop basin and reach the sea floor by cutting all seismic units are considered in the active fault class. However, the faults that remain within Unit 1 and do not reach the seafloor are considered as faults that are coeval with sedimentation. According to these data, faulting in the Central/Eastern Pontide structural block should be reconsidered in the context of the seismic activity of the region and re-evaluated as an earthquake hazard that will pose a risk in the future.

Impact of Pressure and Temperature on Charge Accumulation Characteristics of Insulators in Direct-Current Gas-Insulated Switchgear

Direct-current gas-insulated switchgear (DC GIS) is an important device for promoting the lightweight and compact design of offshore wind power platforms. Gas pressure and temperature gradients are crucial factors that must be considered during the design process of the DC GIS. In this study, the multi-physics coupling model of basin insulators considering surface charge accumulation was established, and the corresponding real-sized insulator surface charge measurement platform was constructed. The effects of gas pressure and temperature gradient on the surface charge accumulation characteristics were investigated, respectively. The results show that the effect of gas pressure on the surface charge distribution characteristics depends on the dominant mode of surface charge. When volume conduction is dominant, the effect of gas pressure on the surface charge is negligible. However, when gas conduction is dominant, the accumulation of a uniform charge pattern on the insulator surface increases with the rise in gas pressure. Furthermore, due to gas convection, the temperature of the upper part of the DC GIS is significantly higher than that of the lower part, which leads to a temperature difference between the upper and lower surfaces of the insulator. The charge density on the insulator upper surface near the central conductor rises with the increase in load current.