Testing Machine Research Articles

Effect of cutting process using cutting insert of grade UTi20T

In the metal-cutting industry, the precision of the metal-cutting process is of paramount importance. Errors in the metal-cutting process not only lead to damage to the cutting tool but also result in the production of low-quality materials. The incorporation of insert materials in the cutting process is aimed at maintaining cutting precision and achieving superior results. This research seeks to investigate the impact of the cutting process utilizing grade KC5410 cutting insert under minimum quantity lubrication (MQL) Conditions. In this study, machining tests were conducted using the ALPHA 1350S 2-axis computer numerical control (CNC) lathe machine under MQL conditions, employing cutting tool inserts UTi20T supplied by Mitsubishi. Two types of tools were utilized in the cutting process, namely UTi20T. Critical aspects such as cutting force, total power consumption, surface roughness, and tool life were analyzed to provide comprehensive insights into the efficiency of the cutting process. The findings of this study significantly contribute to the understanding of how the integration of Grade KC5410 cutting inserts under MQL conditions can enhance the overall efficiency of metal-cutting operations. The successful machinability assessment was conducted by implementing sustainable machining practices.

In-vitro Study Comparing the Shear Bond Values of Zirconia-reinforced Glass Ionomer Cement and Conventional Glass Ionomer Cement

The goal of the current study was to compare the shear bond values of zirconia-reinforced glass ionomer cement and conventional glass ionomer cement. A collection of 20 extracted premolars with unbroken buccal or lingual surfaces was made. The whole sample was randomly split into two groups: Group A (n=10) which was Conventional Glass Ionomer Cement and Group B (n=10) which was Zirconia Reinforced Glass Ionomer Cement (Zirconomer). The process of thermocycling was used to mimic oral conditions. Using a universal testing machine, the shear bond strength (SBS) was measured after 24 hours at a crosshead speed of 0.5 mm/minute until fracture. After tabulating the results, statistical analysis was done. The findings indicated that Zirconomer exhibited a statistically significant (p ≤ 0.05) higher shear bond strength when compared to traditional glass ionomer cement.

Fracture resistance of cement-retained lithium disilicate implant-supported crowns: Effect of material used for two-piece abutments.

This study compared the fracture strength of single lithium disilicate implant-supported crowns fabricated on two-piece abutments with various materials: ceramic-reinforced PEEK, zirconia, and lithium disilicate. Thirty-six implants were embedded in acrylic cylinders. A two-piece abutment and a crown were designed following a pre-operation scan for a maxillary left central incisor. The designed crown was used to fabricate 36 lithium disilicate crowns. The designed abutment was used to manufacture 36 abutments from 3 materials, 12 each: (A) zirconia; (B) lithium disilicate; and (C) ceramic-reinforced PEEK. Abutments were surface treated and bonded on the titanium base abutments with resin cement. Then, lithium disilicate crowns were bonded on the assigned abutments. Specimens were then subjected to dynamic loading for 1,200,000 cycles. The fracture strength (N) of the assembly was assessed using a universal testing machine. One-way ANOVA followed by multiple comparison tests was used to evaluate the effect of abutment material on the fracture strength of single implant-supported restorations at a significance of .05. The average fracture strength for the groups with zirconia, PEEK, and lithium disilicate two-piece abutments were 1362N ± 218N, 1235N ± 115N, and 1472N ± 171N, respectively. There was a significant (p < 0.05) difference in fracture strength among the groups. The lithium disilicate group had significantly higher fracture strength (p = 0.0058) than the group with PEEK; however, there was no significant (p > 0.05) difference between the other groups. Two-piece abutments restored with lithium disilicate crowns investigated in the study have the potential to withstand the average physiological occlusal forces in the anterior region.

Comparison of Different Methods for Determining 5-hydroxymethylfurfural in Assessing the Quality of Honey from Greater Poland

This paper presents the results of testing the content of 5-hydroxymethylfurfural (HMF) in honey from Greater Poland. The production of honey from this area of Poland, its processing, and its consumption are closely related to the sustainable development of this region. It is created in the process of the production, storage, and transport of honey, especially during its thermal processing. Therefore, it can be an indicator in the analysis of sustainable development throughout the life cycle of honey and its products. The aim of this research was to determine the HMF content in Greater Poland’s honey available on the Polish market using three different methods and to compare the obtained results. The methodology used was as follows: two spectrophotometric methods (White and Winkler) and an HMF determination method based on the LC-MS/MS technique developed especially for this study. The determined HMF content in all tested honey samples did not exceed the applicable standard. The determined HMF values in all honey samples ranged from 0 to 28.5 mg HMF/kg honey. All results fell within the scope of European Council Directive 2001/110/EC of 20 December 2001, i.e., they did not exceed the HMF content in honey, which is 40 mg/kg. The results will encourage modifications to the universal honey testing procedures to be developed for the agri-food sector. In the study, seven honeys of different origins and types were selected; three HMF detection methods were selected; a comparative procedure was developed; and the content of the reference ingredient in honey was determined.

Effect of glazing and thermocycling on the fracture toughness and hardness of a New fully crystallized aluminosilicate CAD/CAM ceramic material

BackgroundThe mechanical properties of fully crystallized lithium aluminosilicate ceramics may be influenced by intraoral temperature variations and postmilling surface treatment. The purpose of this study is to explore the interplay among glazing, thermocycling, and the mechanical characteristics (namely, fracture toughness and hardness) of fully crystallized lithium aluminosilicate ceramics.MethodsBending bars (n = 40) cut from LisiCAD blocks (GC, Japan) were randomly assigned to glazed or unglazed groups (n = 20) and subjected to the single edge v-notch beam method to create notches. A glazing firing cycle was applied to the glazed group, while the unglazed group was not subjected to glazing. Half of the specimens (n = 10) from both groups underwent thermocycling before fracture toughness testing. The fracture toughness (KIC) was evaluated at 23 ± 1 °C using a universal testing machine configured for three-point bending, and the crack length was measured via light microscopy. Seven specimens per group were selected for the hardness test. Hardness was assessed using a Vickers microhardness tester with a 1 kg load for 20 s, and each specimen underwent five indentations following ISO 14705:2016. The Shapiro–Wilk and Kolmogorov-Smirnov tests were used to evaluate the normality of the data and a two-way ANOVA was utilized for statistical analysis. The significance level was set at (α = 0.05).ResultsRegardless of the thermocycling conditions, the glazed specimens exhibited significantly greater fracture toughness than did their unglazed counterparts (P < 0.001). Thermocycling had no significant impact on the fracture toughness of either the glazed or unglazed specimens. Furthermore, statistical analysis revealed no significant effects on hardness with thermocycling in either group, and glazing alone did not substantially affect hardness.ConclusionsThe impact of glazing on the fracture toughness of LiSiCAD restorations is noteworthy, but it has no significant influence on their hardness. Furthermore, within the parameters of this study, thermocycling was found to exert negligible effects on both fracture toughness and hardness.

Practical Evaluation of Ionic Liquids for Application as Lubricants in Cleanrooms and under Vacuum Conditions

As part of a publicly funded cooperation project, novel high-performance lubricants (oils, greases, assembly pastes) based on ionic liquids and with the addition of specific micro- or nanoparticles are to be developed, which are adapted in their formulation for use in applications where their negligible vapor pressure plays an important role. These lubricants are urgently needed for applications in cleanrooms and high vacuum (e.g., pharmaceuticals, aerospace, chip manufacturing), especially when the frequently used perfluoropolyethers (PFPE) are no longer available due to a potential restriction of per- and polyfluoroalkyl substances (PFAS) due to European chemical legislation. Until now, there has been a lack of suitable laboratory testing technology to develop such innovative lubricants for extreme niche applications economically. There is a large gap in the tribological test chain between model testing, for example in the so-called spiral orbit tribometer (SOT) or ball-on-disk test in a high-frequency, linear-oscillation test machine (SRV-Tribometer from German “Schwing-Reib-Verschleiß-Tribometer”), and overall component testing at major space agencies (ESA—European Space Agency, NASA—National Aeronautics and Space Administration) or their service providers like the European Space Tribology Laboratory (ESTL) in Manchester. A further aim of the project was therefore to develop an application-orientated and economical testing methodology and testing technology for the scientifically precise evaluation and verifiability of the effect of ionic liquids on tribological systems in cleanrooms and under high vacuum conditions. The newly developed test rig is the focus of this publication. It forms the basis for all further investigations.

On the experimental determination and prediction of damage evolution in composites via cyclic testing

This study introduces a novel approach to obtaining and predicting damage evolution laws using quasi-static cyclic testing within the framework of continuum damage mechanics. To achieve this, a comprehensive set of characterization and parameter identification tests was performed. Carbon-epoxy specimens were manufactured using the filament-winding technique, and these laminates were tested using a universal testing machine. Digital image correlation was employed in all experiments to capture strain fields, and an alternative method utilizing the combined loading compression device is presented to obtain mechanical properties. Once the material was characterized, cyclic tests were conducted, including [Formula: see text], [Formula: see text], and [Formula: see text] tensile tests, and shear v-notch tests. These aim to determine damage evolution laws for both conditions, pure and coupled stress states. From these tests, values for damage onset and threshold were obtained and used to define four new parameters. These parameters permit the estimation of degradation relationships for any arbitrary orientation without requiring additional tests. This approach was tested as the proof-of-concept within the positive range of transverse tension and in-plane shear stress domain. The obtained results are promising, justifying its extension to other failure mechanisms. While acknowledging its limitations, this new approach holds potential for implementation in the analysis of progressive failure in fiber-reinforced composite materials, possibly in conjunction with established failure criteria and computational tools, mainly in the finite element method domain.

Acoustic emission noise reduction: A case of a uniaxial compression test of gypsum-like rock

In acoustic emission tests, the effective signal generated by crack initiation and propagation inside a sample is easily affected by the testing machine, earth vibration and other external noise, which increases the difficulty of data processing and analysis. To solve this problem, a gypsum sample under uniaxial compression is taken as an example to analyze and process the acoustic emission signal during the experiment. The test results show that these noises generally have the characteristics of acoustic sources far from the probe and signal types different from the effective signal. Therefore, a series of methods concerning the noise reduction of acoustic emission signals, including acoustic emission signal preprocessing, acoustic source distance denoising, and acoustic source type denoising, is proposed. Through three analyses and treatments of acoustic emission parameters, noise reduction was achieved with good results. According to the principles of these methods, some suggestions have been put forward for the position of probes in acoustic emission tests; that is, the connection of two probes should not be perpendicular to a weak plane (bedding, joints, etc.). These results could provide a theoretical reference for the postprocessing of acoustic emission signals in mechanical tests.

Evaluation of the Stability of Open-Tray Impression Coping Using Two Different Impression Materials at Three Different Subgingival Implant Placement Depths.

Objective To evaluate and compare the stability of the open trayimpression coping within the set impression while attaching the lab analog when polyether (PE) heavy body and polyvinyl siloxane (PVS) putty impression materials were used and the implant platform was placed sub-gingivally at three different depths. Methods Two impression materials, PE and PVS, and custom-made plexiglass models with embedded single implants to simulate implant positioning depths of 0 mm, 2 mm, and 4 mm, sub-gingivally, were used in the study. Open tray impressions were made after attaching impression coping to theimplant embedded in themodel. Implant lab analog was attached to the impression coping in the set impression, and its stability was measured using a universal testing machine. Forty-two open tray impressions were madein six groups, with seven impressions in each group. Descriptive statistics such as mean and standard deviation were calculated. A comparison of the meanstability between the two impression materials at each depth was done using an independent t-test.Comparison of the mean stability between the three different subgingival implant depths in each material was done by one-way ANOVA with the Scheffe multiple comparison test (post-hoc analysis). The level of significance was set at p<0.05. Results The stability of the impression coping was measured as the force in Newtons required for the displacement of the analog attached to the impression coping embedded in the set impression. PEwith the embedded impression coping at a depth of 0 mm gave the highest mean stability value (4.37+/-0.41), and the least mean stability was offered by PVS with the embedded impression coping at 4 mm depth (1.88+/-0.37). When an independent t-test was done to compare the mean stability values of PE and PVS,there was a statistically significant difference at0 mm, 2 mm, and 4 mm. On doing one-way ANOVA to compare the mean stability between the different depth groups, there was a statistically significant difference between the three depth groups in PE and PVS. Scheffe multiple comparison tests (post-hoc analysis) revealed a statistically significant difference between 0 mm, 2 mm, and 4 mm subgingival depths of the impression coping placement in bothPE and PVS. Conclusion The accuracy of the master cast is an important determinant for the precise fit and long life of the final prosthesis. In the case of maxillary anterior implant placements where deep subgingival placement of the implant platform is needed for aesthetic and functional reasons, the impression material should be selected carefully to ensure the stability of the impression coping. Among the materials included in the present study, the PE impression material offered the maximum stability for impression coping compared to PVS.

Comparative Assessment of the Shear Bond Strength of Ceramic Brackets Bonded to the Enamel Surface with a Self-adhesive System

Objectives: This study aimed to evaluate the shear bond strength of ceramic brackets bonded to the enamel surface using Vertise Flow, with or without the application of phosphoric acid. Materials and Methods: Forty-five extracted human premolar teeth were randomly assigned to three groups (N=15) based on the adhesive used for bonding: 1) Transbond XT, etch, and bond; 2) Vertise Flow; 3) Etch and Vertise Flow. After a 500-round thermocycling procedure, the shear bond strength was measured using a universal testing machine. The samples were then evaluated under a stereomicroscope to determine failure modes, and the Adhesive Remnant Index (ARI) was measured for each group. The data were analyzed with one-way ANOVA and post-hoc Tamhane at a significance level of P&lt;0.05. Results: The highest shear bond strength values were observed in the Transbond XT (13.5±5.38MPa), acid etch and Vertise Flow (11.2±2.89MPa), and Vertise Flow (6.2±3.16MPa) groups, respectively, in descending order. The Vertise Flow group exhibited a significantly lower shear bond strength value compared to the other two groups, with no significant difference between the latter two. Conclusion: While all three study groups demonstrated clinically acceptable shear bond strength values, Vertise Flow showed lower values compared to the other two adhesives. The Vertise Flow composite resin system, whether used alone or with acid etching, remains a suitable choice for bonding ceramic brackets, offering the advantage of a simplified bonding procedure.

Early‐age cracking due to restraint: Laboratory and field investigations on the predictive capacity of the simplified method in Annex D of the future EC2

AbstractThe Annex D of the future EC2 draft gives guidance on the evaluation of early‐age cracking of large structures due to restraint. In case of restrained conditions, compressive stresses are firstly generated in massive structures due to temperature increase, then tensile stresses are generated due to temperature decrease and shrinkage. Due to these tensile stresses, there is a risk of cracking which may be evaluated by the simplified method in Annex D. This method is currently verified against laboratory tests performed in the temperature‐stress testing machine and field cases on restrained concrete elements. The laboratory verification consisted of five approaches to consider different available input (modeled, assumed, or measured). The field investigation focused on the relation between the calculated cracking risk and the observed damage. The results show that the method has very good accuracy and captures with reasonable simplicity the mechanisms and the relations between the parameters involved.

Can a Novel Device with Pure Dry Air Increase the Shear Bond Strength of Dental Composites to Dentin? An Experimental Study

Modern conservative dentistry is taking the lead in daily clinical practice and is relying on adhesion. Whether it is a simple composite, ceramic inlays, onlays, veneers or crowns, the common factor for a successful outcome is a good bonding of these elements to dental structures. Thus, the purpose of this study was to evaluate the bond strength of resin composite to dentin when using a new device, the DENTIPURE KM™ (KM, Beirut, Lebanon), which provides a pure air flow, free of any contaminants and without humidity, when compared to other dental equipment. One hundred and eighty extracted human molars were equally divided into three groups according to the device used, the DENTIPURE KM™ (KM, Beirut, Lebanon), the KAVO™ (ESTETICA E30/E70/E80 Vision, KAVO, Biberach, Germany), or the ADEC™ (A-dec Performer 200, Newberg, OR, USA). The shear bond strength (SBS) was evaluated after 24 h of storage in distilled water on a universal testing machine. Statistical analysis was set with a level of significance at p ≤ 0.05. The results revealed that significantly different bond strength was imparted by the DENTIPURE KM™ device and the ADEC™ dental unit (p = 0.042). In conclusion, while the DENTIPURE KM™ device shows promise in providing contaminant-free air during bonding, its impact on dentin bond strength compared to devices like the KAVO™ appears minimal. Further research is needed to fully assess its potential in enhancing dentinal adhesion procedures.

All-suture anchor size and drill angle influence load to failure in a porcine model of subpectoral biceps tenodesis, a biomechanical study

BackgroundTenodesis of the long head of the biceps tendon is frequently performed in shoulder surgery, and all-suture anchors have become more popular as fixation methods. However, uncertainty still exists regarding the ultimate load to failure of all-suture anchors and the best insertion angle at a cortical humeral insertion point.PurposeThe purpose of this study was to compare the biomechanical characteristics of three types of all-suture anchors frequently used for biceps tenodesis. In addition, the influence of two different insertion angles was observed in a porcine humeri model.MethodsThe ultimate load to failure and failure mode of three types of all-suture anchors (1.6 FiberTak®, 1.9 FiberTak®, 2.6 FiberTak®, Arthrex®) applicable for subpectoral biceps tenodesis were evaluated at 90° and 45° insertion angles in 12 fresh-frozen porcine humeri. The anchors were inserted equally alternated in a randomized manner at three different insertion sites along the bicipital groove, and the suture tapes were knotted around a rod for pullout testing. In total, 36 anchors were evaluated in a universal testing machine (Zwick & Roell).ResultsThe 2.6 FiberTak® shows higher ultimate loads to failure with a 90° insertion angle (944.0 N ± 169.7 N; 537.0 N ± 308.8 N) compared to the 1.9 FiberTak® (677.8 N ± 57.7 N; 426.3 N ± 167.0 N, p-value: 0.0080) and 1.6 FiberTak® (733.0 N ± 67.6 N; 450.0 N ± 155.8 N, p-value: 0.0018). All anchor types show significantly higher ultimate loads to failure and smaller standard deviations at the 90° insertion angle than at the 45° insertion angle. The major failure mode was anchor pullout. Only the 2.6 FiberTak® anchors showed suture breakage as the major failure mode when placed with a 90° insertion angle.ConclusionsAll three all-suture anchors are suitable fixation methods for subpectoral biceps tenodesis. Regarding our data, we recommend 90° as the optimum insertion angle.Clinical relevanceThe influence of anchor size and insertion angle of an all-suture anchor should be known by the surgeon for optimizing ultimate loads to failure and for achieving a secure fixation.

Evaluation of fracture resistance of radicular dentin treated with nanochitosan-loaded calcium hydroxide and nanographene-loaded calcium hydroxide, when used as intracanal medicament: An in vitro study

ABSTRACT Aim: This study aimed to evaluate and compare the effect of using calcium hydroxide (CH) loaded with nanochitosan and nanographene on radicular dentin fracture resistance. Materials and Methods: A total of 40 mandibular premolar root canals were instrumented with the ProTaper rotary system. The fracture resistance of radicular dentin was measured with the universal testing machine, following which intracanal medicament was placed for 10 days. CH alone and CH mixed with nanoparticles of chitosan and graphene were used. Not using any intracanal medicament was used as the control. A one-way ANOVA, followed by the post hoc Tukey’s test, was used to compare the results of different groups. Results: The highest mean for the force at compressive stress was seen in the control group, and the least was recorded by CH. Intergroup comparison for Young’s modulus showed a statistically significant difference (P &lt; 0.05) between the control group and CH (P = 0.002); CH and chitosan + CH (P = 0.003) on post hoc analysis. Conclusion: Incorporation of chitosan and graphene nanoparticles in CH when used as intracanal medicament improves the modulus of elasticity and compressive strength of radicular dentin, which in turn improves dentin elasticity and fracture toughness when compared to CH alone.

The Impact of Bonding Agents and Bone Defects on the Fracture Resistance of Reattached Vertically Root-Fractured Teeth

Many patients experience vertical root fractures, and clinicians often consider conservative treatment options like reattaching the fractured root segments. The study investigated the impact of different bonding agents on the fracture resistance of rebonded vertically fractured teeth with various alveolar bone defects. Human premolar teeth with a single root were sectioned and reattached using dual-cure resin cement (DCRC), resin-modified glass ionomer (RMGI), and cyanoacrylate. The reattached teeth were then restored with a resin fiber post, composite resin core, and full veneer metal copings. These teeth were embedded in acrylic blocks with angular, V-shaped, and step-shaped bone defects to simulate various alveolar bone conditions. After subjecting the samples to thermal cycling, the fracture resistance was evaluated using a universal testing machine. Teeth samples reattached with RMGI exhibited a higher average fracture resistance. The study also found that DCRC proved to be an effective bonding agent for VRF teeth. However, cyanoacrylate-rebonded teeth exhibited the lowest fracture resistance. The V-shaped defects had a significant impact on the fracture resistance of reattached VRF teeth, with largely unfavorable fractures observed in these cases. Predominantly favorable fractures were observed in the teeth treated with RMGI. The fracture loads in both RMGI and DCRC groups exceeded the expected masticatory load.

Cost-effectiveness of the McGill interactive pediatric oncogenetic guidelines in identifying Li-Fraumeni syndrome in female patients with osteosarcoma.

Li-Fraumeni syndrome (LFS) is a penetrant cancer predisposition syndrome (CPS) associated with the development of many tumor types in young people including osteosarcoma and breast cancer (BC). The McGill Interactive Pediatric OncoGenetic Guidelines (MIPOGG) decision-support tool provides a standardized approach to identify patients at risk of CPSs. We conducted a cost-utility analysis, from the healthcare payer perspective, to compare MIPOGG-guided, physician-guided, and universal genetic testing strategies to detect LFS in female patients diagnosed at an age of less than 18years with osteosarcoma. We developed a decision tree and discrete-event simulation model to simulate the clinical and cost outcomes of the three genetic referral strategies on a cohort of female children diagnosed with osteosarcoma, especially focused on BC as subsequent cancer. Outcomes included BC incidence, quality-adjusted life-years (QALYs), healthcare costs, and incremental cost-utility ratios (ICURs). We conducted probabilistic and scenario analyses to assess the uncertainty surrounding model parameters. Compared to the physician-guided testing, the MIPOGG-guided strategy was marginally more expensive by $105 (-$516; $743), but slightly more effective by 0.003 (-0.04; 0.045) QALYs. Compared to MIPOGG, the universal testing strategy was $1333 ($732; $1953) more costly and associated with 0.011 (-0.043; 0.064) additional QALYs. The ICUR for the MIPOGG strategy was $33,947/QALY when compared to the physician strategy; the ICUR for universal testing strategy was $118,631/QALY when compared to the MIPOGG strategy. This study provides evidence for clinical and policy decision-making on the cost-effectiveness of genetic referral strategies to identify LFS in the setting of osteosarcoma. MIPOGG-guided strategy was most likely to be cost-effective at a willingness-to-pay threshold value of $50,000/QALY.

A Baseline Drift-Elimination Algorithm for Strain Measurement-System Signals Based on the Transformer Model

Strain measurements are vital in engineering trials, testing, and scientific research. In the process of signal acquisition, baseline drift has a significant impact on the accuracy and validity of data. Traditional solutions, such as discrete wavelet transform and empirical mode decomposition, cannot be used in real-time systems. To solve this problem, this paper proposes a Transformer-based model to eliminate the drift in the signal. A self-attentive mechanism is utilized in the encoder of the model to learn the interrelationships between the components of the input signal, and captures the key features. Then, the decoder generates a corrected signal. Meanwhile, a high-precision strain acquisition system is constructed. The experiments tested the model’s ability to remove drift from simulated voltage signals with and without Gaussian noise. The results demonstrated that the transformer model excels at eliminating signal baseline drift. Additionally, the performance of the model was investigated under different temperature conditions and with different levels of force applied by the electronic universal testing machine to produce strain. The experimental results indicate that the Transformer model can largely eliminate drift in dynamic signals l and has great potential for practical applications.

Strain Virtual Sensing Applied to Industrial Presses for Fatigue Monitoring

The techniques that allow one to estimate measurements at the unsensed points of a system are known as virtual sensing. These techniques are useful for the implementation of condition monitoring systems in industrial equipment subjected to high cyclic loads that can cause fatigue damage, such as industrial presses. In this article, three different virtual sensing algorithms for strain estimation are tested using real measurement data obtained from a scaled bed press prototype: two deterministic algorithms (Direct Strain Observer and Least-Squares Strain Estimation) and one stochastic algorithm (Static Strain Kalman Filter). The prototype is subjected to cyclic loads using a hydraulic fatigue testing machine and is sensorized with strain gauges. Results show that sufficiently accurate strain estimations can be obtained using virtual sensing algorithms and a reduced number of strain gauges as input sensors when the monitored structure is subjected to static and quasi-static loads. Results also show that is possible to estimate the initiation of fatigue cracks at critical points of a structural component using virtual strain sensors.

In-Vitro Investigation of the Shear Bond Strength of Different Orthodontic Adhesives to Enamel

ABSTRACT Background: The shear bond strength (SBS) of orthodontic adhesives to enamel is a critical factor in the success of orthodontic treatment. Various adhesives are available in the market, each with different trade names and claimed properties that could influence their bond strength. Understanding these differences is essential for clinical decision-making. Materials and Methods: In this in-vitro study, 60 freshly extracted human premolars were collected and randomly divided into four groups: Group A (Adhesive X—Trade Name: BondPlus), Group B (Adhesive Y—Trade Name: OrthoBond), Group C (Adhesive Z—Trade Name: PowerBond), and Group D (Control). The enamel surfaces were cleaned, polished, and etched following standard protocols. Orthodontic brackets were bonded to the teeth using the respective adhesives according to the manufacturer’s instructions. A universal testing machine was employed to measure the SBS, and the data were analyzed using ANOVA with post-hoc tests. Results: The mean SBS values (MPa) were as follows: Group A = 15.2, Group B = 14.8, Group C = 16.5, and Group D (Control) =10.3. Statistical analysis revealed significant differences among the groups (P &lt; 0.05). Post-hoc tests indicated that Group C exhibited significantly higher SBS compared to the other groups. Conclusion: Our findings suggest that among the orthodontic adhesives tested, PowerBond demonstrated superior shear bond strength to the enamel. However, further research is warranted to explore other aspects of adhesive performance and clinical implications.

Associations Between Alcohol Use, Antiretroviral Therapy Use, and Viral Load Suppression Among People Living with HIV in Rural Central Uganda.

Alcohol use among people living with HIV (PWH) is common and may negatively affect engagement in HIV care. We evaluated the relationships between alcohol use, ART use, and viral suppression among PWH in Uganda. PATH/Ekkubo was a trial evaluating a linkage to HIV care intervention in four Ugandan districts, Nov 2015-Sept 2021. Our analytical sample included: (1) baseline data from individuals not enrolled in the interventiontrial (previously diagnosed HIV+); and 12-month follow-up data from the control group (newly diagnosed or previously diagnosed, but not in care). Level of alcohol use was categorized using the Alcohol Use Disorders Identification Test-Consumption (AUDIT-C): none (AUDIT-C = 0), low (women = 1-2, men = 1-3), medium (women = 3-5, men = 4-5), high/very high (6-12). Multivariable logistic regression models evaluated associations between alcohol use, ART use and viral suppression(a viral load of<20); we also stratified by gender. Among 931 PWH, medium (OR: 0.43 [95% CI 0.25-0.72]) and high/very high (OR: 0.22 [95% CI 0.11-0.42]) levels of alcohol use were associated with lower odds of being on ART. In a sub-sample of 664, medium use (OR: 0.63 [95% CI 0.41-0.97]) was associated with lower odds of viral suppression. However, this association was not statistically significant when restricting to those on ART, suggesting the relationship between alcohol use and viral suppression is explained by ART use. Among men, high/very high, and among women, medium alcohol use levels were associated with lower odds of being on ART and beingvirally suppressed. Interventions for PWH who use higher levels of alcohol may be needed to optimize the benefits of Uganda's Universal Test and Treat strategy.