Universal Device Research Articles

Intraoperative lateral wall breach simulation in the cadaveric spine and the impact of thread designs of screws on pullout strength in the osteoporotic thoracic vertebrae: A biomechanical study in human cadavers.

This study aimed (1) to simulate pedicle screw pullout after intraoperative external wall perforation and (2) to assess restoration strength with different thread designs in the pedicle screw instrumentation for osteoporotic thoracic vertebrae. Twenty fresh-frozen human cadaveric thoracic vertebra bodies were prepared and divided into 4 groups: group 1, 5.5 mm × 45 mm polyaxial single thread pedicle screws (PASTS); group 2, after wall injury 5.5 mm × 45 mm PASTS; group 3, 6.5 mm × 45 mm PASTS after wall injury; and group 4: 6.5 mm × 45 mm polyaxial mixed-threaded screws after wall injury. While group 1 was the control group, groups 2, 3, and 4 were used as study groups after the lateral wall breach. All prepared screw units were placed on a universal pullout measurement testing device. The mean bone mineral density for 20 thoracic vertebrae was 0.57 ± 0.12 g/cm2 (range 0.53-0.6 g/cm2 ). The mean pullout strength was 474.90 Newtons (N) for group 1, 412.85 N for group 2, 475.4 N for group 3, and 630.74N for group 4. The lateral wall breach caused a 14.1 % decrease in average pullout strength compared with the initial screw pullout. Mixed (double)-threaded screws increased pullout strength compared to 6.5 mm screws (P=.036) Conclusion: Using a 1 mm thicker polyaxial pedicle screw or mixed (double)-threaded pedicle screw seems to increase pullout strength; however, this was statistically significant only for group 4. In the thoracic spine, the redirection possibility of the pedicle screw is limited, and augmentation with cement will not be appropriate due to the risk of wall injury-related leakage. Therefore, care should be taken to avoid violating the lateral cortex by using appropriate pedicle entry points and trajectories.

Numerical and experimental investigation of a new model of friction damper in diagonal brace under cyclic loading

Owing to the performance of prefabricated friction dampers, which are rapidly increasing, the resistance of structural systems against earthquakes increases and depreciates the energies generated by earthquakes in the structure. It is important to use passive control systems to control the vibrations of a structure at a single level. However, in the design, they cannot depreciate the incoming energy from earthquakes at different levels. Friction dampers focus on displacement variables and are mostly used in steel structures according to the rules of a Coulomb damper or a friction brake that converts kinetic energy into heat through friction. In this study, a new type of friction damper, called a flat cylindrical friction damper, was designed using brake pads in a diagonal brace. The performance and seismic resistance of this system, as well as the amount of energy loss, were investigated. In this study, 18 laboratory tests were conducted using the universal device to check the research variables, their hysteresis diagrams were shown, and the configuration of the damper was designed such that grooved bolt connections and twin steel cables of different sizes and thicknesses were used. Moreover, the way the internal and external components are placed in the damper is such that innovation in tension and pressure has been created. In addition, the movement of the cylindrical element in the damper increased the amount of friction, owing to the presence of two types of brake pads with friction coefficients of 0.11 and 0.16 and the bolt connections. This demonstrates the damper performance under different sliding forces at different friction levels. The geometric dimensions, thickness of the brake pad, number and size of bolts, diameter of cables, sliding force, and location of the damper were among the variables investigated in this study. Brake pads, steel cables, and bolt connections are important and economically affordable. The seismic performance of the intended frame was investigated using 80 different damper models and the placement of the research variables. The desired optimal models were modelled using Abaqus software, analysed, and designed. This system aims to reduce the relative horizontal displacement of floors and increase the amount of energy absorption. An increase in theaxial-force created in multiple loading cycles always causes damage to damper components and frames. In this study, we used a special multi-level geometry to reduce the axial-force created in the damper, the relative displacement of the frame, and damages in the elements, as well as increase the ductility. The results show that the friction surfaces of steel plates and brake pads is very high due to the displacement and damping of the cables. Additionally, with the consumption of energy and its absorption by the damper in cyclic loads, displacement is easily controlled. The seismic response of the structures in terms of frame and damper displacement, base shear forces, and energy absorption is also observed. Numerical studies confirmed that the intended damper is an independent seismic-resistant member in critical building structures when high seismic performance or seismic resilience during moderate and strong earthquakes is desirable.

Self-etching primer versus hydrofluoric acid and air-abrasion: effects on flexural and resin bond strengths of resin-based CAD/CAM material

This study aimed to evaluate the effect of self-etching primer (Monobond Etch & Prime; MEP), hydrofluoric acid (HF), and air-abrasion (A) protocols on shear bond strength (SBS) of resin cement and flexural strength (FS) of nanoparticle-filled resin-based CAD/CAM material. Bar- and rectangular-shaped specimens (n = 130 for each) were obtained from a resin-based material (Cerasmart 270). The specimens were divided into 13 subgroups according to surface treatments: Control (C); HF for 60, 90, and 120 s; MEP for 60, 90, and 120 s; air-abrasion for 10, 15, and 20 s; air-abrasion followed by HF; air-abrasion followed by MEP; HF followed by MEP. Surface roughness (Ra) values were measured using a profilometer (Surftest SJ-210) by applying 9 readings per specimen. One specimen per group was examined by atomic force microscopy (AFM; Multimode 8) in a 20 μm × 20 μm area, and scanning electron microscopy (SEM; EVO LS-10) under ×1000 magnification. FS and SBS data were obtained using a universal test device (Marestek) at a crosshead speed of 1 mm/min. Air-abraded groups showed the highest Ra (A10: 1.331 ± 0.213; A15: 1.409 ± 0.110; A20: 1.491 ± 0.111; A + HF: 1.415 ± 0.138; A + MEP: 1.309 ± 0.071 μm) and the lowest FS values (A10: 122.59 ± 16.80; A15: 118.94 ± 11.74; A20: 117.22 ± 11.18; A + HF: 114.42 ± 18.09; A + MEP: 128.98 ± 19.74 MPa). FS values of HF- and/or MEP-applied groups were statistically similar to the control group (C: 167.37 ± 27.02; HF60: 186.74 ± 30.66; HF90: 162.79 ± 29.31; HF120: 184.11 ± 17.18; MEP60: 171.98 ± 29.65; MEP90: 162.49 ± 20.38; MEP120: 173.55 ± 22.50; HF + MEP: 175.09 ± 21.64 MPa). SBS values of MEP-applied groups were higher than those of HF-etched groups with the same duration. Significant differences in SBS values were found after etching protocols with different durations (HF60: 4.14 ± 0.64; HF90: 4.48 ± 0.33; HF120: 6.76 ± 1.65; MEP60: 6.24 ± 1.23; MEP90: 9.92 ± 1.25; MEP120: 10.22 ± 1.27 MPa). Prolonged MEP application (90 s and 120 s) can be the preferred surface treatment for resin-based CAD/CAM materials. However, air-abrasion may adversely affect its mechanical properties.

Bond strength comparison of a fiber-reinforced composite resin: Different dentin conditions and preparation techniques.

This study aimed to compare the bond strength of a fiber-reinforced composite resin with traditional and bulk-fill composite resins under different dentin conditions and preparation techniques. Eighty molar teeth, excluding the mesio-distal half of the occlusal dentin surfaces of each teeth, were isolated with acid-resistant nail varnish and stored in a demineralisation solution (pH 4.5). After mechanical removal of the varnish, the teeth were buried in acrylic resin blocks. In every composite resin group, one-half of the specimens were prepared with a diamond bur and another half with Er: YAG laser. Then, the specimens were divided into four groups of composite resins (Filtek Z250, G-aenial Posterior, SonicFill 2, Ever X Posterior) (n = 10). Shear bond strengths were measured using a universal testing device, and failure types were determined with stereomicroscope images. SEM images were obtained at 1000× magnification. Data were analyzed using a three-way analysis of variance (ANOVA), and Bonferroni correction was used for multiple comparisons (p = .05). Differences in the dentin surface affected the bond strength results (p < .05), whereas there was no significant difference between cavity preparation methods (p > .05). EverX Posterior showed the highest bond strength results. Within the limitations of this study, fiber-reinforced composite resin exhibited successful bond strength results in addition to improved mechanical properties. RESEARCH HIGHLIGHTS: Fiber-reinforced composite had successful bond strength values. Bond strength values of sound dentin groups were higher than those of caries-affected dentin groups. The use of an Er: YAG laser for preparation did not lead to insufficient bond strength results.

Использование программно-определяемого радио для структурного анализа энергоемких веществ с помощью ядерного магнитного резонанса

This article discusses the creation of a system using software-defined radio for the study of energy-intensive substances using nuclear magnetic resonance. Software-defined radio (SDR) uses technology that allows to configure or change the parameters of radio frequency operation through software, such as frequency range, modulation type and output power. The article presents the structure of the system and provides a detailed analysis of several key components. The proposed approach involves the use of a SDR transmitter-receiver, which is a universal device capable of both transmitting and receiving signals. The article describes the stages of signal processing and suggests potential directions for the development of the system in the future. By using the SDR architecture and software interface, the system achieves a close location between sampling, digital-to-analog and analog-to-digital conversions, minimizing noise and distortion created by the analog part of the spectrometer. The SDR allows the use of quadrature modulation and demodulation, digital filtering and amplification, as well as software adjustment of filter characteristics. The article highlights the problems associated with the development of such NMR systems. The advantages of the system include enhanced capabilities for the development of new spectroscopic methods, compact dimensions for easy portability and cost-effectiveness compared to commercial spectrometers.

Shear bond strength of calcium silicate-based cements to glass ionomers

BackgroundA shear bond strength between the biomaterial and restorative material is crucial for minimizing bacterial microleakage and ensuring a favorable long-term prognosis for vital pulp therapy. This study aimed to conduct a comparative evaluation of the shear bond strength between calcium silicate-based biomaterials utilized in vital pulp treatment and various glass ionomer cement materials, both with and without the application of adhesive agents.MethodsA total of 270 acrylic blocks, each featuring cavities measuring 4 mm in diameter and 2 mm in depth, were prepared. Calcium silicate-containing biomaterials (ProRoot MTA, Medcem Pure Portland Cement, and Medcem MTA), following manufacturers’ instructions, were placed within the voids in the acrylic blocks and allowed to set for the recommended durations. The biomaterial samples were randomly categorized into three groups based on the restorative material to be applied: conventional glass ionomer cement, resin-modified glass ionomer cement, and bioactive restorative material. Using cylindrical molds with a diameter of 3.2 mm and a height of 3 mm, restorative materials were applied to the biomaterials in two different methods, contingent on whether adhesive was administered. After all samples were incubated in an oven at 37 °C for 24 h, shear bond strength values were measured utilizing a universal testing device. The obtained data were statistically evaluated using ANOVA and post-hoc Tukey tests.ResultsThe highest shear bond strength value was noted in the Medcem MTA + ACTIVA bioactive restorative material group with adhesive application, while the lowest shear bond strength value was observed in the ProRoot MTA White + Equia Forte HT Fil group without adhesive application (P < 0.05).ConclusionActiva Bioactive Restorative may be considered a suitable restorative material in combination with calcium silicate-based biomaterials for vital pulp treatment. The application of adhesives to calcium silicate-based biomaterials can effectively address the technical limitations.

Optimization process of filling the cocoons with process water in a universal vacuum-steaming device

This article presents the results of a study carried out to optimize the process of filling the inner surface of cocoons with process water in a domestically produced universal vacuum-steaming device. Optimization was carried out according to the definition of a second-order polynomial Regression Multifactor Model (RMM) based on the results of the Rotatable Central Composition Experiment (RCCE). For this purpose, experiments were carried out in several versions on a universal vacuum-steaming device at different water temperatures and steaming durations. Keywords. Cocoons, vacuum, universal, optimal, parameter, raw silk, steaming, experiment, factor, temperature, duration, preparation, unwinding, sericin.

Investigation of the Fracture Strength Between Dental Implant And Ti-Base Abutment Produced with Different Heights and Grades of Titanium Material

New prosthetic designs were developed to provide a balanced transmission of the stress caused by the chewing function to other mechanical and anatomical structures, and these designs revealed new research areas. An example of this is screw-retained implant-supported prostheses. With screw-retained prostheses, the residual cement problem is eliminated. However, abutment material and abutment design may adversely affect the mechanical and aesthetic properties of prostheses. Ti-base abutments have been developed to solve these problems. However, studies on clinical succes, material content and abutment height of ti-base abutments remain up-to-date. In our study, the effect or abutment heights on the bond strength and stress distribution with monolithic zirconia crowns in ti-base abutments manufactured from different titanium Gr types will be tested. Titanium Gr 4, Gr 5 and Gr 23 ELI materials will be used in our study. A total of 7 groups are planned with ti-base abutments with a abutment length of 3.5 mm, 5.5 mm for Gr 4 and Gr 5, abutment length of 3.5 mm, 5.5 mm and 7 mm for Gr 23. In the in vitro experiment, the fracture strength of the samples will be tested with the universal testing device. total of 77 implants, ti-base abutments and monolithic zirconia crowns will be used by creating 11 samples for each study group. The obtained values will be recorded in Newtons and Megapascals. The data will be analysed using the SPSS 22.0 programme. As a result, while the lowest fracture strength values were observed in Gr 4 Ti material in all ti-base abutment lengths in the samples for which the fracture strength test was performed, similar values were observed in the ti-base abutments produced from Gr 5 and Gr 23 ELİ alloys. When the relationship of bonding strengths with Ti alloys was evaluated, it was seen that there was no significant difference between Ti alloys.

Methods of mechanical tests for cantilever loading of metatarsal foot bones

The development and implementation of methods for quantitative assessment of biomechanical parameters of osteotomies are important issues in modern orthopedics. The analysis of characteristics of different types of osteotomies is of great significance, as it can contribute to reducing complications and improving surgical treatment of the foot. In order to conduct experiments on bones with unchanged mechanical properties, a new method of fixing bone samples was developed and tested, which allows for mechanical testing in cantilever bending and/or axial compression on the day of bone material extraction, which was previously impossible due to a number of problems. During the study, a universal steel device was designed that allows for fixing the sample at a 15-degree angle to the horizontal. The device's universality lies in the fact that the tube, in which the sample is fixed, can be detached and then installed on a stationary crossbar of the testing machine, which ensures axial compression of the sample at a 15-degree angle to the vertical axis. A comparative analysis of adhesive compositions of three types for fixing the material in the device was also conducted. It was found that a mixture of cyanoacrylate glue and baking soda allows for conducting experiments without loss of mechanical properties of bone tissue. Thus, the developed and described methodology by the authors allows for preparing samples of the metatarsal bone for testing under cantilever loading in a short period of time, which eliminates changes in the properties of bone tissues due to a long break between extraction and experiment, as well as due to bone freezing.

Investigating the effect of fundamental properties of materials on the mechanisms of thermal cracking of asphalt mixtures

In most of tests and models to evaluate the thermal cracking of asphalt mixture, the consideration of different elements within the asphalt mixture has been neglected to provide a corrective solution. Accordingly, in this research, the evaluation of the mechanisms of thermal cracking involved assessing the impact of surface free energy (SFE) parameters and other fundamental properties of bitumen and aggregate. These parameters included the adhesion and cohesion free energy, the ratio of the base element to the acid element of the aggregate SFE (RBA), the creep stiffness of bitumen, the rate of changes in creep stiffness (m-value), and specific surface area (SSA) of aggregate. To this end, Wilhelmy plate (WP) test, universal sorption device (USD) test, the bending beam rheometer (BBR) test and the pull-off test were performed. In the following, models were presented to evaluate the effect of mentioned parameters as independent variables on the mechanisms of thermal cracking using an artificial neural network (ANN). The sensitivity analysis of the Artificial Neural Network (ANN) model revealed that in the status of adhesive failure, the cohesion free energy and m-value did not affect the Pull-off adhesion strength. On the other hand, the adhesion free energy, RBA, and the SSA were directly proportional and the creep stiffness was inversely proportional to the Pull-off adhesion strength. Also, in the status of cohesive failure, the adhesion free energy, the RBA, and the SSA did not affect the Pull-off cohesion strength. On the other hand, the cohesion free energy and m-value were directly proportional and the creep stiffness was inversely proportional to the Pull-off cohesion strength.

Evaluation of the shear bond strength of various adhesives on the surface of enamel irradiated with various doses of radiotherapy

We aimed to compare the shear bond strength (SBS) forces on the enamel surface with 2 adhesives after treatment with various radiation doses. A total of 120 premolars were included in the study. The teeth were randomly divided into 5 main groups (n= 24): negative control (without aging), positive control (with aging), 40 Gy, 60 Gy, and 70 Gy radiation. The 40 Gy, 60 Gy, and 70 Gy groups underwent conventional radiotherapy 5 days a week with a dose of 2 Gy each day. After the radiotherapy, all samples except the negative control group were subjected to thermal cycle aging. In all 5 groups, the specimens were divided into 2 subgroups, and half were bonded using 2 adhesives. After bonding, the universal Shimadzu test device was used to analyze the SBS. After the test, the tooth surfaces were examined under a stereomicroscope to determine the adhesive remnant index. When adhesives were compared, Biofix adhesive's bond strength value was statistically higher in the 40 Gy group than in the Transbond XT group (P= 0.001). The SBS value was higher in all irradiated groups than in nonirradiated groups (P= 0.001). When the adhesive remnant index score was analyzed, no significant difference was found among the groups. The SBS increased in irradiated teeth compared with unirradiated teeth, and the SBS values of both adhesives were within the acceptable limits in all radiation groups.

The Effect Of Er,Cr:YSGG Laser Conditioning on Dentin Bond Strength and Nanoleakage of Universal Adhesive Systems: An In Vitro Study.

To investigate the effect of erbium, chromium: yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser conditioning on dentin bond strength and nanoleakage of different universal and self-etch adhesives. A total of 84 intact human third molar teeth were cut at the dentin level, and half of them were laser conditioned. The specimens were divided into three groups; two different universal resins and one self-etch adhesive resin were applied and composite resin restorations were created. For the microtensile bond strength (µTBS) test, 20 microspecimens were prepared from the laser and control group of each adhesive (n = 20) and tested with a universal device. For nanoleakage observation, 10 specimens were prepared from each group (n = 10) and stored in silver nitrate solution, and then the amount of nanoleakage was analyzed by field emission scanning electron microscopy (FESEM). Data were analyzed with two-way ANOVA, Tukey's honestly significant difference, and chi-square tests. The mean dentin bond strength of all adhesives in the laser groups was found to be statistically significantly lower than those of the control groups (P < .05). No difference was found between the mean bond strength of the adhesives in the laser and control groups (P > .05). Higher nanoleakage was observed in all adhesives in the laser groups compared to the control groups (P < .05). Irradiation of the dentin surface with Er,Cr:YSGG could adversely affect the µTBS and nanoleakage, likely by affecting the structure of the hybrid layer.

Comparison of Shear Bond Strength of Three Types of Adhesive Materials Used in the Restoration of Permanent Molars after Treatment with Silver Diamine Fluoride: An In Vitro Study.

Permanent blackish discoloration of the tooth structure post application of silver diamine fluoride (SDF) is one of its drawbacks. Several restorative materials have been used to restore and mask the blackish discoloration of SDF-treated teeth. Recently, a new self-adhesive material has been introduced and is marketed as an all-in-one etchant, adhesive, and restorative material indicated for use in all clinical situations. This study aimed to assess the shear bond strength of the new self-adhesive restorative material and compare it with adhesive restorative materials- resin-based composite and resin-modified glass ionomer cement to dentin of extracted permanent teeth treated with 38% SDF. Thirty-nine caries-free extracted teeth (n = 39) were grouped into three groups. Following 38% SDF application, the specimens were loaded with resin-based (Group I), the new self-adhesive restorative material (SDR) Surefil (Group II), and resin-modified glass ionomer cement (RMGIC) (Group III). Shear bond strength (SBS) was calculated, and failure modes were evaluated using the universal testing device (3) Results: The composite showed the highest bond strength, followed by Group II while Group III had the lowest bond strength of all tested materials. Regarding failure type, the composite showed 100% adhesive failure, while Group III and Group II showed mostly adhesive failure with some combination. (4) Conclusions: RBC had a significantly stronger SBS to demineralized dentin surfaces of permanent molar teeth treated with SDF when compared to SDR Surefil and RMGIC.

Effect of Irrigation with Different Solutions on Push out Bond Strength of Root Canal Obturation Materials

Evaluate push out bond strength (PBS) of endodontic obturation materials after washing by NaOCl, EDTA, and MTAD. Materials and methods: 30 mandibular premolars were utilized. Root canal instrumentation of all samples was achieved by ProTaper universal files to size F4. Samples were distributed to 3 groups; each group involved 10 samples as the following: Group1- samples were lastly washed by 5 ml of 5.25% NaOCl for 5 minutes. Group2- samples were lastly washed by 5 ml of 17% EDTA for 5 minutes. Group3- samples were lastly washed by 5 ml of MTAD for 5 minutes. All samples were filled by single cone technique with AH Plus sealer, and F4 ProTaper gutta-percha cone. 3 sections of 2 mm thickness were transected from every sample at 3, 7, and 11 mm from root apex, which represented apical, middle, and coronal sections consecutively. PBS was tested by universal digital testing device. Failure modes were assessed by stereomicroscope at 40 X magnification. Lastly, collected data was analyzed statistically. Results: MTAD group revealed significant greatest mean of PBS followed by EDTA group, and NaOCl group revealed significant least mean of PBS. In all groups, greater mean of PBS was in coronal section followed by middle section while, lesser mean of PBS was in apical section though, the differences among them were not significant within the same group. Mixed and cohesive failures were most dominant modes of failure in MTAD, and EDTA groups. While, in NaOCl group adhesive, and mixed failures were most dominant. Conclusions: last washing with MTAD is better than that with EDTA, and NaOCl in terms of greatest PBS.

The Effect of Various Disinfection Methods on The Tensile Bond Strength of Soft Lining Material

Disinfection of dentures and resilient denture liners were preferred for cross-contamination treatment and better safety. Nevertheless, it has been found that these techniques affect the physical and mechanical properties of denture liners. Objective: To evaluate the impact of various disinfection methods on the tensile bond strength of acrylic soft liner. Material and Methods: 25 samples were made, then divided randomly into five groups (4 disinfection groups as well as a control group), after the daily disinfection procedure, distilled water was used to store the samples at room temperature. After 30 days, a universal testing device (Gester, China) was used to assess the tens ile bond strength. The machine applied force to the specim ens at a crosshead constant speed of 5 mm/minute until failure was recorded. Statistics software (SPSS) was used to analyze the measurements. Results: After 30 days of regular ex posure to different disinfection methods, a greater mean value for bond strength showed in the control group while the lesse r value was in the chlorhexidine group. No significant difference was found between the control and Protefix tablet groups. The sodium hypochlorite and microwave groups had no significant difference between them, but they were significantly different from the control, Protefix tablet, and chlorhexidine groups. the chlorhexidine group was significantly different from the control and other disinfected groups. Conclusion: All disinfected soft liners revealed a decrease i n tensile bond strength, which was not significant with the protefix cleansing tablet but significant with the chlorhexidine, sodium hypochlorite, and microwave regimes.

An In Vitro Comparison of Shear Bond Strength for Heated Composite Resin With Three Conventional Luting Cements.

Forty-eight lithium disilicate disc samples are collected and put on acrylic blocks for this investigation. To improve luting cement adhesion, the discs are etched with 5% hydrofluoric acid (HF) gel. For easier handling and lower viscosity during luting, the composite resin is heated to between 55 and 68°C on a digital wax melter. Shear bond strength tests were executed with the universal testing device after the following luting cement was applied in the center of the test specimen (lithium disilicate discs). Statistics software was used for the calculations and analysis. In accordance with the findings of the tests, shear bond strengths ranged from 2.2851 ± 0.5901 for nanohybrid composite resin to 7.3740 ±0.6969 for self-adhesive resin cement and 4.4647 ± 0.9774 for light-activated resin cement. A statistically significant (p≤0.001) difference between the groups was found. Mean shear bond strength was significantly highest in the self-adhesive resin cement group, followed by the light-activated resin cement group, resin-modified GIC, and least with the nanohybrid composite resin group. Composite resins; in fixation of indirect restorations can have their viscosity reduced by preheating in a device, but they must be employed as soon as possible after removal.Standardizing the methods of heating composite resins for cementation is necessary to achieve desirable outcomes and direct the physician in their application. Although preheating composite resins for luting operations can be utilized to decrease the material's viscosity and enhance the restoration setting; it may not increase bond strength.

Universal device for two-qubit entangled measurements via photonic quantum walks

Universal device for two-qubit entangled measurements via photonic quantum walks

Comparative evaluation of effect of chlorhexidine application on dentin bond strength with two different adhesives after ER, CR: YSGG phototherapy: an in vitro study.

This study aimed to assess the efficacy of phototherapy with an Er, Cr:YSGG laser on the bond strength of dentin using two different adhesive systems after chlorhexidine (CHX) application. Twenty-four non-carious human molar teeth were separated into three main groups: negative control Group A (Group A), CHX and phototherapy with an Er, Cr:YSGG laser (Group PC), and CHX with conventional diamond bur (no phototherapy) (Group C). These groups were divided into two subgroups based on adhesives: Clearfil Universal Quick Bond and Clearfil SE Bond. To evaluate the microtensile bond strength, the occlusal enamel surfaces of the teeth were removed with a low-speed, water-cooled diamond bur to expose hard dentin tissue. The teeth within Group PC were treated with Er, Cr:YSGG phototherapy. The surfaces were then disinfected with 0.2% chlorhexidine gluconate. Subgroups were applied according to the manufacturer's instructions using the adhesive systems mentioned above. Following adhesive application, the teeth were restored with composite resin. A microtensile bond strength test was performed on the test sticks obtained from the teeth using a universal test device. Data were analyzed using variance analysis (ANOVA) at a significance level of p < 0.05. Among all groups, the highest bond strength was achieved with Clearfil SE Bond with CHX + phototherapy (45.6 ± 4.2), while the lowest was achieved with Clearfil Universal Quick Bond without phototherapy (control group) (27.0 ± 6.7) (p < 0.05). Phototherapy with Er, Cr: YSGG following chlorhexidine application enhanced the bond strength of both the bond systems (p < 0.05).

STUDY OF THE PROGRAMMABLE ISOKINETIC SAMPLER EFFICIENCY FOR OF ECOLOGICAL DIAGNOSTICS SYSTEMS OF HEAT ENGINES AND BOILER PLANTS

The work is devoted to the solution of the actual scientific and practical task of creating a universal sampling device for systems of environmental diagnostics of heat engines and boiler plants of various purposes. Ensuring the isokinetic mode of sampling from the exhaust pipe (EP) of the engine is a more difficult task than carrying out a similar sampling process in the chimney of the boiler plant, since the exhaust gases of the engines are characterized by fluctuations of static pressures in the HT with an amplitude of up to ±500 Pa, which must be taken into account in the operation of the sampling equipment. In the course of research, based on the analysis of global and domestic experience in the production and use of equipment for environmental certification of internal combustion engines and boiler houses, a programmable isokinetic sampler (ICT) was created, which allows you to take a proportional part of the gas sample from the full flow of exhaust gases in the EP of the power plant with accuracy ±3%. Motorless and motorized test stands have been developed for modeling and research of gas-dynamic processes in the exhaust systems of engines and boiler plants, which provide the possibility of varying the parameters of gas flows - mass flow rate, speed, temperature, static pressure, velocity pressure in the ranges: 15 - 55 g/s; 5...30 m/s, 20...180 °С, 0...2.5 kPa, 10 - 550 Pa, respectively. On the basis of the created test stands, empirical dependences were established to determine the static pressure differences between the ICP and EP pipelines, in which the isokinetic mode of sampling is ensured, from the dynamic pressure of the gas flow in the EP. With the help of these dependencies, SMART control of the programmable ICP is carried out. An experimental development of the programmable ICP was carried out as part of the MT-1 minitunnel during environmental tests of the 1СН12/14 diesel engine in separate modes and according to the ESC cycle established by the UNECE Regulations R-49. The research results confirmed the compliance of the created sampling device with regulatory requirements for its design and the accuracy of determining the sampling coefficient.

Clinical Nurses' Identification of a Wearable Universal Serial Bus Used for Pediatric Oncology Clinical Trial Participant Safety Management.

The expanded access to clinical trials has provided more patients the opportunity to participate in novel therapeutics research. There is an increased likelihood of a patient, as a pediatric oncology clinical trial participant, to present for clinical care outside the research site, such as at an emergency room or urgent care center. A novel wearable universal serial bus device is a proposed technology to bridge potential communication gaps, pertaining to critical information such as side effects and permitted therapies, between research teams and clinical teams where investigational agents may be contraindicated to standard treatments. Fifty-five emergency and urgent care nurses across the United States were presented, via online survey without priming to the context of clinical trials or the device, a picture of a pediatric patient wearing the novel wearable device prompted to identify significant, environmental cues important for patient care. Of the 40 nurses observing the patient photo, three identified the wearable device within Situational Awareness Global Assessment Tool formatted narrative response fields. Analysis of the narrative nurse-participant responses of significant clinical findings upon initial assessment of the pediatric patient photo is described, as well as the implications for subsequent prototyping of the novel universal serial bus prototype.