Universal Biquad Research Articles

Universal Current-Controlled Current-Mode Biquad Filter Employing MO-CCCCTAs and Grounded Capacitors

This paper presents a universal current-controlled current-mode biquad filter employing current controlled current conveyor trans-conductance amplifiers (CCCCTAs). The proposed filter employs only three MO- CCCCTAs and two grounded capacitors. The proposed filter can simultaneously realize low pass (LP), band pass (BP), high pass (HP), band reject (BR) and all pass (AP) responses in current form by choosing appropriate current output branches. In addition, the pole frequency and quality factor of the proposed filter circuit can be tuned independently and electronically over the wide range by adjusting the external bias currents. The circuit possesses low active and passive sensitivity performance. The validity of proposed filter is verified through PSPICE simulations.

Multiple-Mode OTA-C Universal Biquad Filters

Two new multiple-mode (including voltage, current, transconductance, and transresistance modes) OTA-C universal biquad filters are proposed. The first proposed circuit uses only four operational transconductance amplifiers (OTAs) and two grounded capacitors. The second proposed circuit uses five OTAs and two grounded capacitors. Both the proposed circuits can realize voltage, current, transconductance, and transresistance mode universal filtering responses (low-pass, high-pass, band-pass, notch, and all-pass) from the same topology. The first proposed circuit uses the least number of components. This represents an attractive feature from a chip area and power consumption point of view. The second proposed circuit has no need of extra inverting and non-inverting amplifiers for special input signals. Moreover, both the proposed biquads still have (i) the employment of two grounded capacitors, (ii) cascadable connection of the former voltage-mode stage and the latter current-mode stage, and (iii) low sensitivity performance. H-SPICE simulation results confirm the theoretical analysis.

Voltage mode universal filters employing single FDCCII

In this paper, four new voltage-mode universal biquad filters configuration are proposed. First of two circuits proposed high-input impedance universal filter with single-input and three-outputs, which can simultaneously realize voltage mode low-pass, band-pass and high-pass filter responses employing all grounded passive components. The third proposed universal filter three-input and single-output, which also can realize all the standard filter functions. The fourth circuit proposed universal filter with three-input and five-outputs, which can be used as either a three-inputs single-output or a two-inputs five-outputs universal filters. It can realize all five different generic filtering signals: low-pass, band-pass, high-pass, band-stop and all-pass. Simulation results are given to confirm the theoretical analysis. The proposed biquad filters are simulated using TSMC CMOS 0.35 μm technology.

Single CCII-based voltage-mode universal filter

A new voltage-mode universal biquad filter is presented which can realize all the five standard filter functions namely lowpass, bandpass, highpass, notch, and allpass employing only one CCII as ac...

ELECTRONICALLY TUNABLE CURRENT-MODE UNIVERSAL BIQUAD FILTER USING DUAL-X CURRENT CONVEYORS

In this paper, an electronically tunable current-mode (CM) universal biquad filter is proposed. The proposed filter employs three dual-X second-generation current conveyors (DXCCIIs), two grounded capacitors and four NMOS transistors acting as resistors. The proposed filter simultaneously realizes standard filter functions such as low-pass (LP), band-pass (BP), and high-pass (HP) responses. The notch (NH) and all-pass (AP) functions can also be obtained by connecting appropriate output currents directly without using additional active elements. The output signals are obtained at high output impedance terminals, which is important for easy cascading in CM operation. SPICE simulation results are given to verify the theoretical analyses.

Current-controlled current differencing transconductance amplifier and applications in continuous-time signal processing circuits

This article presents the design for a basic current-mode building block for analogue signal processing, named as Current Controlled Current Differencing Transconductance Amplifier (CCCDTA). Its parasitic resistances at two current input ports can be controlled by an input bias current. As it can be applied in current-mode of all terminals, it is very suitable to use in a current-mode signal processing, which is continually more popular than a voltage one. The proposed element is realized in a bipolar technology and its performance is examined through PSPICE simulations. They display usability of the new active element, where the maximum bandwidth is 65 MHz. The CCCDTA performs low-power consumption and tuning over a wide current range. In addition, some examples as a current-mode universal biquad filter, a current-mode multiplier/divider and floating inductance simulator are included. They occupy only single CCCDTA.

Multi-function biquad using single current differencing transconductance amplifier

An universal multi input single output type multifunction biquad is proposed. The proposed configuration employs only one current differencing transconductance amplifier as the active element, two capacitors and three resistors. The circuit realizes all five filter functions (i.e. Low Pass, High Pass, Band Pass, Notch and All Pass) without changing the circuit topology. The natural frequency ?0 is independently and electronically tunable. The workability of the proposed multifunction biquad has been verified using SPICE simulation.

Fully integrable mixed-mode universal biquad with specific application of the CFOA

In this paper, a novel mixed-mode universal filter using a single new active device namely specific current feedback operational amplifier (SCFOA) is suggested. Mixed-mode called as dual-mode can provide either current-mode (CM) or voltage-mode (VM) responses with relevant input port selections. The proposed CM filter can simultaneously realize low-pass, band-pass and notch filter responses, and can provide high-pass and all-pass filter responses with interconnection of the relevant output currents. Further, the VM filter selection can provide universal filter responses. The CM and VM biquads offer independent control of angular resonance frequency ( ω 0 ) and quality factor ( Q ), and have low active and passive component sensitivities. However, CM filter is more suitable for integrated circuit (IC) process because of consisting of only grounded passive elements. A number of computer simulations by means of SPICE program are included to confirm the claimed theory.

Tunable mixed-mode OTA-C universal filter

A novel electronically tunable mixed-mode universal biquad by using four single-output and one dual-output-operational transconductance amplifiers, two grounded capacitors is proposed. The proposed circuit has ability to realize voltage, current, transconductance, and transresistance mode, and can the following advantageous features: (i) realization of low-pass, band-pass, high-pass, notch, and all-pass filter responses from the same configuration, (ii) employment of only grounded capacitors ideal for integrated circuit implementation, (iii) orthogonal controlling of ? o and Q for easily electronic tunability, and (iv) low active and passive sensitivity performance. Finally, to verify our architecture, we have designed this analog filter chip with TSMC 0.35-μm 2P4M CMOS technology. This chip operates to 1 MHz and consumes 30.95 mW. The chip area of the analog filter is about 0.823 mm2.

Single-resistance-controlled quadrature oscillator and universal biquad filter using CFOAs

This paper presents new single-resistance-controlled (SRC) sinusoidal quadrature oscillator and universal biquad filter circuits with reduced number of passive elements using only two current-feedback operational amplifiers (CFOAs). The first proposed oscillator configuration comprising two CFOAs, three resistors and two capacitors provides two sinusoidal voltage outputs in phase quadrature. The circuit has the advantage of independent control of the condition of oscillation and the oscillation frequency through a single resistor. The second proposed biquad filter configuration consisting of only two CFOAs, two resistors and two capacitors realizes all the standard types of the biquadratic filter functions at low-impedance output without any component matching conditions. The filter also provides orthogonal control of the natural angular frequency ( ω 0 ) and the bandwidth (BW). In addition, both proposed circuit configurations have good active and passive sensitivity performances. PSPICE simulations and experimental results based on commercially available AD844-type CFOAs are included, showing the excellent performance of the proposed configurations.

Cascadable Current-Mode Biquad Filter and Quadrature Oscillator Using DO-CCCIIs and OTA

This article introduces a circuit which can function both as a quadrature oscillator and as a universal biquad filter (lowpass, highpass, bandpass). When the circuit functions as a universal biquad filter, the quality factor and pole frequency can be tuned orthogonally via the input bias currents. When it functions as a quadrature oscillator, the oscillation condition and oscillation frequency can be adjusted independently by the input bias currents. The proposed circuit can work as either a quadrature oscillator or a biquad filter without changing the circuit topology. The amplitude of the proposed oscillator can be independently controlled via the input bias currents. The proposed oscillator can be applied to provide amplitude modulated/amplitude shift keyed signals with the above-mentioned major advantages. The circuit is very simple, consisting of four dual-output second generation current controlled current conveyors (DO-CCCIIs), one operational transconductance amplifier (OTA), and two grounded capacitors. Without any external resistors and using only grounded elements, this circuit is therefore suitable for IC architecture. PSPICE simulation results are depicted here, and the given results agree well with the theoretical analysis. The power consumption is approximately 7.32 mW at ±2.5 V supply voltages.

A CMOS Digitally Programmable Universal Current-Mode Filter

A new digitally programmable universal current-mode biquad filter is proposed. The filter is based on digitally controlled current followers (DCCFs). It utilizes gains of the DCCFs to provide precise frequency and/or gain characteristics that can be digitally tuned over a wide range. All parameters of the proposed filter can be adjusted independently. Experimental results obtained from a 0.35-mum standard CMOS chip are provided.

Current controlled current conveyor transconductance amplifier (CCCCTA): a building block for analog signal processing

This article presents a basic current-mode building block for analog signal processing, namely current controlled current conveyor transconductance amplifier (CCCCTA). Its parasitic resistance at current input port can be controlled by an input bias current. It is very suitable for use in current-mode signal processing, which is becoming more popular than voltage mode. The proposed element is realized in a bipolar technology and the performances are examined through PSPICE simulations, displaying usabilities of the new active element. The CCCCTA performs tuning over a wide current range. The description includes some examples as a current-mode universal biquad filter, voltage-mode universal biquad filter, a grounded inductance simulator, a current-mode multiplier/divider and an oscillator. They occupy only a single CCCCTA.

Electronically tunable versatile voltage-mode universal filter

A novel electronically tunable versatile voltage-mode universal biquad filter by using two single-output-operational transconductance amplifiers (OTAs), one differential difference current conveyor (DDCC) and two capacitors is proposed. The proposed circuit, which can be used as either a four-input single-output universal filter or a single-input three-output multifunction filter with the same topology. Besides, the new circuit offers the following advantageous features: realization of all the non-inverting and inverting biquadratic filter signals from the same configuration, no need to employ inverting-type input signals, no need to component-matching conditions and low passive sensitivity performance.

CMOS current-controlled current differencing transconductance amplifier and applications to analog signal processing

This article presents design of a basic current-mode building block for analog signal processing, named as current-controlled current differencing transconductance amplifier (CCCDTA). Its parasitic resistances at two current input ports can be controlled by an input bias current. Owing to working in current-mode of all terminals, it is very suitable to use in a current-mode signal processing, which is continually more popular than a voltage one. The proposed element is realized in a CMOS technology and is examined the performance through PSPICE simulations. They display usability of the new active element, where the maximum bandwidth is 311 MHz. The CMOS CCCDTA performs low power consumption and tuning over a wide current range. In addition, some examples as a current-mode universal biquad filter, floating inductance simulator and quadrature oscillator are included. They occupy only single CCCDTA.

New voltage-model/current-mode universal biquad filter using unity-gain cells

A new universal biquad filter is presented which can realize all the five standard filter functions namely lowpass, bandpass, highpass, notch and allpass in voltage-mode (VM) as well as in current-mode (CM) employing only unity-gain cells (i.e. voltage followers and current followers) as active elements. Explicit VM/CM outputs are available from low output impedance terminals and high output impedance terminals, respectively. The workability of the proposed universal biquad, realized with CMOS unity-gain cells, is established by SPICE simulations.

New Universal Biquads Employing CFOAs

Four new single-input-multi-output-type universal biquad filters using current-feedback operational amplifiers (CFOAs) are presented, which realize all the five standard filter functions (namely, low-pass, bandpass, high-pass, notch, and all-pass) from the same configuration, provide tunability of the various filter parameters in all the five responses, and offer a resistive or ideally infinite input impedance while employing only four CFOAs and two grounded capacitors as preferred for integrated circuit implementation. The workability of the new biquads has been verified by hardware implementations and SPICE simulations based upon AD844-type CFOAs, and some sample results are presented

Analytical Synthesis of the Digitally Programmable Voltage-Mode OTA-C Universal Biquad

None of the recently reported voltage-mode versatile filters are digitally programmable for applications like the easy addition of current-mode filtering signals to do the synthesis. None of the recently reported analytical synthesis methods are used for the realization of a multifunction filter. Both the above two induced motivations of researches have been merged, developed, and solved in this brief on the voltage-mode operational transconductance amplifier (OTA)-C universal biquad filter, which still achieves many advantages like the employment of all single-ended-input OTAs, all grounded capacitors, and the least number of active transistor and passive component counts, in addition to having a controllable gain, a cascadable input terminal, and the absence of the need to impose component matchings

New universal filter using only current followers as active elements

A new universal current-mode (CM) biquad filter is presented which can realise all the five standard filter functions namely lowpass, bandpass, highpass, notch and allpass employing only unity-gain current followers (CF) as active elements. The workability of the proposed universal biquad, realised with CMOS unity-gain current followers, is established by SPICE simulations. The new circuit provides explicit CM outputs from high output impedance terminals and possesses a number of advantageous features all of which are not available simultaneously in any of the previously reported CF-based universal biquad filters.

Single FDCCII-Based Tunable Universal Voltage-Mode Filter

None of the previously reported voltage-mode universal biquad filters with three inputs and a single output offers either of the following two important advantages: (i) the use of only one active element and (ii) independent control of ω0 and ω0/Q. In this paper, a novel biquad filter, achieving both of these advantages, is presented. HSPICE simulation results using TSMC025 process and ±1.25 V supply voltages validate the theoretical predictions.