Unipolar Pulse Research Articles

Design of a Rectangular Wave High Voltage Generator for the Evaluation of Inverter-Fed Motor Insulation

The urgent need for the safer operation of inverter-fed motors is leading research to the qualification tests under high frequency rectangular wave voltages. Consequently, the generation of rectangular wave voltages with adjustable parameters has become a major concern for manufacturers and researchers. This paper presents a design of high frequency and high voltage pulse generator able to provide unipolar or bipolar pulses up to 20 kV peak-to-peak with variable rise and fall time that can be tuned down to 40 ns. Such a generator is performant enough for testing a large part of motors following standards and with more stressful conditions for research of new winding technologies. Resorting to high voltage push-pull solid-state switches and dielectrics liquid & air-cooling technique, the tested capacitance load can reach up to 3000 pF. Also, the over-current protection circuit is carefully designed and verified by using real-time logic control hardware. The proposed generator has been successfully used for endurance tests and partial discharge inception voltage (PDIV) detection at repetitive impulsive voltages for capacitive, inductive insulation structures and windings during the qualification evaluation of inverter-fed motors.

Long-duration bipolar linear transformer driver based on a multi-turn half-bridge structure

All-solid linear transformer driver(LTD) generators are widely used to output unipolar high-voltage rectangular pulses in nanoseconds. However in some applications, the bipolar output is necessary and the size of the generator is limited, which is challenging for LTD topology because the size of the magnetic core is related directly to the amplitude and pulse duration of the output waveforms. In this paper, a bipolar long-duration pulse generator based on the topology of a linear transformer driver combined with a half-bridge and multi-turn structure is put forward. The half-bridge topology can output bipolar waveforms easily and can save the number of switches used in the generator. To eliminate the crosstalk voltage that appears during operation, a differential mode inductance is used to protect the circuit. A snubber circuit is applied to suppress the reverse overshoot. The multi-turn design is chosen to make the size more compact. However, the multi-turn usually leads to a lower rise speed. To improve the performance, an optimization method that improves the rising speed by changing the turns of each stage is discussed. The strategy is useful and can be applied on some other occasions. The generator can output bipolar waveforms whose amplitudes are 4 kV and the duration can be adjusted from 200 ns to 800 ns. The rise time can be limited to 70 ns. The size of the generator is 10 cm * 10 cm * 15 cm, which is compact compared to the generators put forward before.

The possibility of anesthesia stimulated by a train of current pulses

This study considers a simple theoretical model of blocking the passage of signals (action potentials) from sensory neurons, thereby affecting anesthesia without the use of anesthetics as a result of a sequence of unipolar current pulses generated by an external source. The proposed model allows the selection of parameters and the required frequency of the repetition of current pulses for the possible implementation of anesthesia, depending on the electrical characteristics of the skin and the conductivity of the saline solution in which the myelinated nerve fibers are located.

Radiation of a Solitary Polarization Pulse Moving at the Speed of Light

Photons have zero rest mass and always travel at the speed of light in a vacuum, but have no dipole moment. Atoms and molecules, which may have a constant or variable dipole moment, have mass and therefore cannot move at or above the speed of light. As a result, the radiation from such systems moving at the velocity of light was not considered. However, it is possible to create many artificial objects (light spots, effective charges, current pulses, etc.) that can travel at the speed of light and even exceed it. In this case, they become a source of electromagnetic radiation. In this work, the radiation of a solitary polarization pulse that travels at the speed of light and has a variable or constant amplitude is discussed. It is shown that if the amplitude does not change, then such an object does not radiate outward; i.e., the field emitted by it remains completely localized inside the moving polarization pulse. If the amplitude changes over time, then it begins to radiate backwards. In this case, unipolar pulses of an unusual shape, such as a rectangular one, can be obtained.

Next generation CANCAN focusing for remote stimulation by nanosecond electric pulses

Focusing electric pulse effects away from electrodes is a challenge because the electric field weakens with distance. Previously we introduced a remote focusing method based on bipolar cancellation, a phenomenon of low efficiency of bipolar nanosecond electric pulses (nsEP). Superpositioning two bipolar nsEP into a unipolar pulse canceled bipolar cancellation (“CANCAN” effect), enhancing bioeffects at a distance despite the electric field weakening. Here, we introduce the next generation (NG) CANCAN focusing with unipolar nsEP packets designed to produce bipolar waveforms near electrodes (suppressing electroporation) but not at the remote target. NG-CANCAN was tested in CHO cell monolayers using a quadrupole electrode array and labeling electroporated cells with YO-PRO-1 dye. We routinely achieved 1.5–2 times stronger electroporation in the center of the quadrupole than near electrodes, despite a 3–4-fold field attenuation. With the array lifted 1–2 mm above the monolayer (imitating a 3D treatment), the remote effect was enhanced up to 6-fold. We analyzed the role of nsEP number, amplitude, rotation, and inter-pulse delay, and showed how remote focusing is enhanced when re-created bipolar waveforms exhibit stronger cancellation. Advantages of NG-CANCAN include the exceptional versatility of designing pulse packets and easy remote focusing using an off-the-shelf 4-channel nsEP generator.

Radiation of a Solitary Polarization Pulse Moving at the Speed of Light

Photons have zero rest mass and always travel at the speed of light in a vacuum, but have no dipole moment. Atoms and molecules, which may have a constant or variable dipole moment, have mass and therefore cannot move at or above the speed of light. As a result, the radiation from such systems moving at the velocity of light was not considered. However, it is possible to create many artificial objects (light spots, effective charges, current pulses, etc.) that can travel at the speed of light and even exceed it. In this case, they become a source of electromagnetic radiation. In this work, the radiation of a solitary polarization pulse that travels at the speed of light and has a variable or constant amplitude is discussed. It is shown that if the amplitude does not change, then such an object does not radiate outward; i.e., the field emitted by it remains completely localized inside the moving polarization pulse. If the amplitude changes over time, then it begins to radiate backwards. In this case, unipolar pulses of an unusual shape, such as a rectangular one, can be obtained.

Light-induced dynamic microcavities created in a resonant medium by collision of non-harmonic rectangular 1-fs light pulses

Recently, interest in extremely short unipolar electromagnetic pulses with non-harmonic shape (e.g. rectangular or triangular) is rising. Such pulses do not contain a carrier frequency and have an ultra-wide spectrum. Compared to conventional harmonic multicycle pulses, they are faster and more efficient in controlling the properties of quantum systems, which allows, in the future, for faster data transmission and processing. With coherent interaction of extremely short light pulses with a medium, formation and ultrafast control of population difference gratings and polarization structures are possible when the pulses both overlap and do not overlap in the medium. In this work, based on the numerical solution of Maxwell–Bloch equations, we demonstrate possible creation of a dynamic “microcavity” as a burst of population difference, arising from the collision of rectangular unipolar 1-femtosecond pulses of self-induced transparency in a two-level resonant medium. Potential to control the microcavities parameters (changing the depth, turning it on, erasing it, etc.) is demonstrated.

Population density gratings produced by a pair of nonharmonic unipolar rectangular attosecond pulses in a resonant medium

Recently, the possibility of obtaining non-harmonic unipolar electromagnetic pulses with a specific electric field strength’s dependence on time (e.g. a rectangular pulse) has been actively discussed in optics. Unipolar pulses have a nonzero electric area and a wide spectrum: from zero frequency up to the visible region. This could open up wide application of such pulses, for example, for faster and more efficient control of the quantum systems’ properties with a high temporal resolution compared to conventional bipolar multicycle pulses. In this paper, based on an approximate solution of the time dependent Schrödinger equation and a numerical solution of the equation system for the density matrix, we show the possibility of creating electromagnetically induced population density gratings in an atomic medium using a pair of unipolar rectangular attosecond light pulses that do not overlap in the medium. The formation of such gratings can be explained on the basis of the concept of ‘interference’ of electric pulse areas, recently introduced into optics.

Analysis of the double-side power supply for electronic-ion technology devices with pulse voltage

This article provides an analysis of existing high voltage power supply devices for devices of electron-ion technology, in particular devices for cleaning gases from aerosol particles. Advances in this technology are described. The following are the disadvantages of the electric fields of a corona discharge when powered by a constant high voltage. To increase the efficiency of catching aerosol particles, the authors propose to combine self-sustained and non-sustained discharges in one discharge gap. To do this, it is proposed to use unipolar high-voltage pulses with a constant component and pulses with a duty cycle of more than 5. An analysis is made of the possibility of increasing the efficiency of the impact of electric fields when using circuits with two-sided power supply, the analysis of which makes it possible to increase the pulse repetition rate, as well as to regulate the process of the impact of electric fields on processed particles., regulation by the parameter of impulse voltage.

H9 and H10 Transformer-Less Solar Photovoltaic Inverters for Leakage Current Suppression and Harmonic Current Reduction

Now-a-days, transformer-less inverters integrating renewable energy resources as solar photovoltaic systems are commonly employed in many grid-connected distributed energy systems in both industrial and residential settings. Transformer-less photovoltaic (TLPV) inverters have attracted increased attention due to their unique advantages, such as increased efficiency, low cost, and ease of installation. Converting fluctuating solar dc power to consistent ac power has been a difficulty in the recent decade to avoid security risks like ground fault currents and leakage currents. Leakage current minimization is one of the most crucial factors in the TLPV inverters. Different TLPV inverter topologies have been presented in the past, with leakage current being reduced by galvanic isolation on the dc or ac side of the inverter, common mode voltage (CMV) clamping, and modulation techniques. This paper proposed two novel single-phase grid-tied TLPV inverter topologies with control blocks, which can handle a wide variety of grid voltages. The proposed TLPV inverters offer very small leakage current, reduced total harmonic distortion (THD), and improved power quality. Based on the number of semiconductor devices, the proposed inverters are termed as H9 and H10 inverters. The switches are controlled using the unipolar sinusoidal pulse width modulation, which results in constant common mode voltage and reduction in leakage currents to 11.09 and 11.73 mA for the proposed H9 and H10 inverters, respectively. The proposed H9 and H10 inverters minimize the THDs to 1.62 and 2.09%, respectively. Besides, the proposed H9 and H10 inverters exhibit 98.19 and 98.12% European efficiency. The simulations are carried out on MATLAB/Simulink and the results are experimentally validated using downscale laboratory test platforms

Nonharmonic Spatial Population Difference Structures Created by Unipolar Rectangular Pulses in a Resonant Medium

Nonharmonic Spatial Population Difference Structures Created by Unipolar Rectangular Pulses in a Resonant Medium

Evidence for fireballs in bipolar HiPIMS plasmas

Using laser Thomson scattering (LTS) and 2D optical imaging, a fireball-like discharge is detected during the positive pulse period of bipolar voltage waveforms, for a circular planar unbalanced magnetron with W target operating in argon. These reverse discharges, excited for positive pulse voltages V pp from 200 to 300 V, sit primarily on the discharge centreline. Their establishment is delayed relative to the initiation of the positive pulse, with the delay time shortening with increased V pp: they are clearly attached to the target (anode in this phase) and have lifetimes extending to the end of the positive pulse. LTS measurements of the electron temperature T e show dramatic electron heating (T e rises from 1 up to 3 eV) both on the discharge centre line and above the racetrack during the fireball event. This is consistent with greater light intensities from the broad band optical imaging of the discharge. In the fireball phase, the LTS measurements also show greatly reduced election densities (by a factor of 5) in the magnetic trap (directly above the racetrack) compared to the unipolar pulse case. The existence of such anodic fireballs is quite possibly an unwanted effect in bipolar HiPIMS.

Frequency Domain Electromagnetic System Based on Unmanned Aerial Vehicles Platform for Detecting Shallow Subsurface Targets

Due to the advantages of being nondestructive, rapid, and convenient, the electromagnetic detection method has attracted growing interest in the field of shallow subsurface detection. With the rapid development of unmanned aerial vehicle (UAV) technology, the use of the UAV platform for measurement can not only improve work efficiency but also avoid the significant losses that may be caused by humans working in dangerous areas. Therefore, we propose a broadband frequency domain electromagnetic system AFEM-3 based on a UAV platform for shallow subsurface targets detection (within less than 2 m). The sensor head adopts a concentric planar coil structure with a high spatial resolution, and a bucking coil connected in reverse series with the transmitting coil is used to suppress the primary field at the receiving coil. We designed a transmitting module based on unipolar frequency multiplication sinusoidal pulse width modulation technology that can generate multi-frequency arbitrary combination transmitting waveforms with low total harmonic distortion. It can also be matched to a variety of different transmitter coils by using the same hardware circuit. In addition, the global navigation satellite system and inertial measurement unit are integrated on the sensor head. The measurement response value, position, and attitude information can be displayed in real-time through the host computer. Through the static experiment of a standard coil, we verified the consistency between the AFEM-3 system with the theory. The performance of the system was evaluated through field experiments. The experimental results show that the system can effectively detect multiple metal targets in shallow subsurface areas. For different metal targets, the AFEM-3 system can provide obvious frequency domain characteristics.

Spatially and velocity-selective magnetization preparation for noncontrast-enhanced peripheral MR angiography.

The purpose of the current study was to develop spatially and velocity-selective (SVS) magnetization preparation pulses for noncontrast-enhanced peripheral MR angiography (MRA) to provide comparisons with velocity-selective (VS) MRA with comparison to velocity-selective (VS). VS preparation pulses were designed by concatenating multiple excitation steps, each of which was a combination of a hard RF pulse, VS unipolar gradient pulses, and refocusing RF pulses. SVS preparation pulses were designed by replacing the hard RF pulse with a sinc-shaped RF pulse combined with a symmetric tripolar gradient pulse (which does not perturb the velocity encoding by the VS unipolar gradient pulses). Numerical simulations were performed to verify the intended hybrid excitation selectivity of SVS pulses taking account of tissue relaxation, magnetic field errors, and eddy currents. In vivo experiments were performed in healthy subjects to verify the hybrid excitation selectivity, as well as to demonstrate the visualization of the entire peripheral arteries using six-station protocols. As demonstrated by numerical simulations, SVS preparation yielded a notch-shaped longitudinal magnetization (Mz )-velocity response within the spatial stopband (the same as VS preparation) and preserved the Mz of spins outside the stopband, regardless of its velocity. We confirmed these observations also through in vivo tests with good agreement in normalized arterial and muscle signal intensities. In six-station peripheral MRA experiments, the proposed SVS-MRA yielded significantly higher arterial signal-to-noise ratio (SNR) (51.6 ± 14.3 vs. 38.9 ± 10.9; p < 0.001) and contrast-to-noise ratio (CNR) (41.2 ± 13.0 vs. 31.3 ± 10.5; p < 0.001) compared with VS-MRA. The proposed SVS-MRA improves arterial SNR and CNR compared with VS-MRA by mitigating undesired presaturation of arterial blood upstream the imaging field of view.

On the Possibility of Intense Unipolar THz Pulses Formation in Nonhomogeneous Nonequilibrium Nitrogen Plasma Channels

We developed a 3D, fully self-consistent model for analysis of the ultrashort THz unipolar pulse formation accompanied by its amplification in a nonequilibrium plasma channel induced in nitrogen by a femtosecond UV laser pulse. The model is based on a self-consistent numerical solution of the second-order wave equation in cylindrical geometry and the kinetic Boltzmann equation for the electron velocity distribution function (EVDF) at different points of the spatially inhomogeneous nonequilibrium plasma channel. Rapid relaxation of the electron velocity distribution function in the plasma channel results in the amplification of the leading front of the THz pulse only, while its trailing edge is not amplified or even absorbed, which gives rise to the possibility of the formation of pulses with a high degree of unipolarity. The evolution of the unipolar pulse after its transfer from the channel to open free space is analyzed in detail.

Enhanced dielectric and energy storage properties of P(VDF-HFP) through elevating β -phase formation under unipolar nanosecond electric pulses

Structural manipulation of electroactive β-phase of poly(vinylidene fluoride-co-hexafluoropropylene) [P(VDF-HFP)] is of great importance in high-energy-density polymer devices. In this Letter, an efficient way to improve dielectric and energy storage properties of P(VDF-HFP) films by inducing a high β-phase content and lowering the crystallite size through repetitive unipolar nanosecond electric pulses (nsEP) is proposed. It is found that the percentage of the β-phase in P(VDF-HFP) can be significantly enhanced to ∼84% under a low unipolar nsEP of 5 V/mm vs only 35% in pristine P(VDF-HFP). Meanwhile, the orientation of the amorphous chains is also achieved, which improves the dielectric constant, electric breakdown, and energy storage properties of P(VDF-HFP). Specifically, the P(VDF-HFP) film processed under nsEP of 5 V/mm exhibits a high breakdown field of 541 MV/m, and discharged energy density of 14 J/cm3, which is 28.8% and 127% higher than those of the pristine polymer, respectively. This work provides a facile approach to optimize the crystalline morphology of P(VDF-HFP) polymers for dielectric energy storage applications.

Peculiarities of Excitation of a Particle in a Single-Level Quantum Well by an Extremely Short Attosecond Pulse

Using the solution of the time-dependent Schrodinger equation, the features of the excitation of a bound state of a particle in a one-dimensional rectangular quantum well of small depth by an extremely short light pulse are studied. The case of a shallow well with only one energy level is considered. In this case, the system is excited by an attosecond pulse whose duration is shorter than the characteristic time associated with the energy of the bound state of the particle in the well. It is shown that in this case the population of the bound state and the ionization probability are determined by the ratio of the electric area of the pulse to its atomic scale, which is inversely proportional to the well width. The calculation results showed that unipolar subcycle pulses with nonzero electric area can excite the system faster and more efficiently than bipolar pulses with zero area. The possibility of using unipolar gamma-ray pulses of zeptosecond duration for deuteron excitation is discussed, and numerical estimates of the required duration and electric area of the pulse are given. Keywords: extremely short pulses attosecond pulses, unipolar pulses, electric area of a pulse, atomic scale of electric area, one-dimensional quantum wells, nanostructures.

Особенности возбуждения частицы в одноуровневой квантовой яме предельно коротким аттосекундным импульсом

Using the solution of the time Schrödinger equation, the features of the excitation of a bound state of a particle in a one-dimensional rectangular quantum well of small depth by an extremely short light pulse are studied. The case of a shallow well with only one energy level is considered. In this case, the system is excited by an attosecond pulse whose duration is shorter than the characteristic time associated with the energy of the bound state of the particle in the well. It is shown that in this case the population of the bound state and the ionization probability are determined by the ratio of the electric area of the pulse to its atomic measure, which is inversely proportional to the well width. The calculation results showed that unipolar subcycle pulses with nonzero electric area can excite the system faster and more efficiently than bipolar pulses with zero area. The possibility of using unipolar gamma-ray pulses of zeptosecond duration for deuteron excitation is discussed, and numerical estimates of the required duration and electric area of the pulse are given.

Superradiance of a Stopped Polarization Pulse in a Thin Layer of a Five-Level Medium Excited by Subcycle Attosecond Pulses

Using the numerical solution of the system of equations for the amplitudes of bound states, together with the wave equation, we theoretically consider stopped polarization pulse superradiance upon excitation by a pair of half-period attosecond pulses in a thin layer of a five-level resonant medium, the parameters of which are the same as in a hydrogen atom. It is shown that in the case of a multilevel medium, at certain parameters of the exciting field, the superradiance pulse near the medium is also a single-cycle pulse, the shape of which is determined by the first time derivative of the stopped polarization pulse, as in the case when approximate low-level and classical models were used to describe the response of the medium. Keywords: superradiance, attosecond pulses, stopped polarization pulse, unipolar pulses, subcycle pulses.

Development of Bipolar Pulse Power Supply Based on Peak Closed-Loop Control Method

With the wide application of pulsed power technology in tumor ablation, sewage treatment, and other related fields, researchers have found that bipolar electrical pulses are more effective than unipolar electrical pulses. In this article, a new bipolar pulse generator is proposed, which combines the features of boost circuit and Marx circuit to significantly improve the boost ratio of output pulse and the tunability of pulse peak. In order to improve the load regulation rate and peak stability of bipolar pulse power supply, a bipolar pulse power supply based on peak closed-loop control method is designed in this article. The high-voltage pulse is attenuated, and its peak is sampled by the pulse peak sampling circuit, and the pulse peak voltage is fed back to the DSP controller for comparison with the set peak value, and the proportional integral differential (PID) adjustment is performed according to the voltage deviation, and the boost ratio of the pulse generator is changed to realize the constant peak output of the bipolar pulse. In order to verify the feasibility of the proposed bipolar pulse generator with peak closed-loop control scheme, simulation and experimental studies of the bipolar pulse power supply with five-stage peak closed-loop control were conducted. The results show that the output repetition frequency of 5 kHz, pulsewidth of 5– <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$10~\mu \text{s}$ </tex-math></inline-formula> , and peak pulse value within ±2.0 kV can be stabilized when the input voltage is 100 V.