Uniform Temperature Distribution Research Articles

Study on Thermal Metamaterial for Uniform Surface Temperature Distribution

Abstract This paper proposes a thermal metamaterial based on the theory of thermodynamics transformation, which can achieve uniform temperature distribution. The required anisotropic thermal conductivity is theoretically derived. This thermal metamaterial structure is achieved by alternating aluminum and polyimide of different lengths. The temperature distribution under the condition of different convective heat transfer coefficients was simulated and compared with pure aluminum. The simulation and experimental results show that the metamaterial significantly reduced the non-uniformity of the temperature distribution.

Numerical simulation of physical field during different ultrasonic power assisted casting of 7085 aluminum alloy

High‐energy ultrasound has the effect of purifying the aluminum (Al) melt and improving the uniformity of temperature and flow field distribution. In this paper, a finite element numerical model of ultrasonic‐assisted casting of 7085 Al alloy melt was established, and the changes of acoustic pressure field, temperature field and flow field in the solidification process of alloy melt with different ultrasonic power were investigated. The numerical simulation results show that the thickness of the 7085 Al melt mushy zone decreases by 89 mm, 97 mm, 108 mm, 114 mm and 99 mm, respectively, compared without ultrasonic (WNU) when the ultrasonic power was 150 W, 350 W, 550 W, 750 W and 950 W. The area of the alloy mushy zone increases by 38.1%, 43.5%, 61.0%, 206.5% and 45.6%, respectively. According to numerical simulation results, when the ultrasonic power was 750W, it had the best effect on improving the macroscopic physical field, increasing the mass and heat transfer rate in the center of the Al melt. Meanwhile, the experimental results of industrial melting and casting of 7085 large‐scale Al alloy ingots were basically consistent with the numerical simulation, which provided technical support for ultrasonic‐assisted fabrication of large‐scale 7085 Al alloy ingots.This article is protected by copyright. All rights reserved.

The effects of outlet size, shape, and location on spatial temperature distribution reduction via direct jet impinging in power electronics

Power electronics are used daily in a wide range of applications. Overheating is a major problem associated with power electronic chips. Direct jet impingement on silicon-based chips has emerged as a promising technique for power electronics cooling. However, this technique results in variations in spatial temperature between the center of the jet and the jet outlet location. This paper introduces a jet outlet design that facilitates a more uniform spatial temperature distribution. To this end, a numerical model is developed for a jet impingement configuration featuring four top circular outlets and experimentally validated using a thermal test chip with a jet Reynolds number of 7000. The resultant data show that reducing the outlet size by 30% results in a 31% decrease in the spatial temperature variance between the stagnation point and hot spot locations.Five outlet configurations are also investigated: eight circular top outlets; eight circular side outlets; four square top outlets; eight square top outlets; and eight square side outlets. Analysis of the temperature profiles of these designs reveals that the configuration featuring eight top circular outlets produces the highest spatial temperature difference, while the configuration featuring four top circular outlets (1.4 mm diameter) produces the smallest difference. Specifically, the four top circular outlet design enables a 42 % reduction in the spatial temperature difference, with a 3.8 % decrease in the pressure drop between the main inlet and outlet. Additionally, the findings show that this configuration produces a higher increase in the hot spot heat-transfer coefficient compared to the eight top circular outlet configuration (from 18,500 to 22,300 w/m2 °C, an increase of 20.5 %), thus flattening the spatial heat-transfer coefficient radially.

Research on the influence of floating brake pad structure on the friction interface performance of disc brake

The friction contact state of the brake friction interface of high-speed trains in the braking process affects the braking efficiency, which in turn affects the braking safety and the service life of the components. This paper focuses on the heat and stress distribution at the friction interface under the action of a floating brake pad structure. (Question 6) A floating brake pad structure comprising two sets of spherical joint structure is introduced. The multi-body structure and rigid-flexible coupling effects of the floating brake pad are considered. Furthermore, a full reproduction flexible thermo-mechanical coupling braking model in the floating brake pad structure is constructed. The accuracy of the model is validated by conducting tests on a 1:1 scale high-speed train brake test bench. The temperature and stress distribution of the fixed/floating brake pad structure at 80 km/h are studied accordingly. The results show that: In accordance with the temperature outcomes derived from the simulation model, the observed temperature variations in the test results, demonstrating an average error of 8.93%. The action of the floating brake pad resulted in a significant reduction of 36.99% in the maximum surface temperature of the brake pad, as well as a reduction of 30.91% in the maximum stress. The temperature of the brake disc surface is decreased by 32.01%, while the maximum stress experienced a decrease of 30.65%. The contact area of the friction interface is increased by 100%. The floating brake pad is demonstrated a more uniform distribution and consistent gradient of temperature and stress across its friction interface in comparison to the fixed brake pad. (Question 1)

Inkjet-printed heater on flexible substrates for low voltage applications

Flexible heaters (FHs) have applications ranging from defoggers to flexural warmers, food processors, and thermotherapy. Printed FHs are particularly of interest as they offer unique advantages like high resolution, customization, low cost, and ease of fabrication. Here, we report printed FHs on polyethylene terephthalate substrate. The heater design is optimized to operate on a low voltage of five volts and yield high temperatures with a uniform temperature distribution across the surface. The heater has a fast response time of 15 s to reach its maximum temperature and does not show any degradation in performance after three months of operation. The heater maintains its temperature after continuous use for two hours and exhibits a minimum change in temperature upon bending. We have also developed and tested designs for zone heaters and nano heaters, where zone heater is suited for applications requiring heating in specified locations on a surface only. Whereas nano heater has an area of 1 mm2 and can produce high temperatures in this small area. Finally, we developed similar printed heaters on paper and polyimide (PI) substrates as well. Paper-based heater can achieve a temperature of 210 °C and can be used in disposable applications due to its low cost, whereas PI heater can achieve a temperature of 380 °C and is suitable for attaining high temperatures. These results manifest the use of FHs for various practical applications.

Thermal enhancement of PEM fuel cell cooling with novel configurations of Tesla valve and hybrid nanofluids: A numerical study

The operating temperature and thermal distribution play a significant role in the appropriate performance of the proton exchange membrane fuel cell (PEMFC). A suitable cell cooling method can guarantee uniform temperature distribution and preservation of membrane water content under harsh conditions in a PEMFC. The compact structure of PEM fuel cells and the size of the cooling system impose a great challenge to achieve a proper design of cooling plate. In this numerical study, four designs of the multi-stage Tesla valve with straight and reverse configuration are proposed to be employed as a cooling channel in which three different hybrid nanofluids such as TiO2–Cu, Al2O3–CuO, and Ag–MgO dispersed in water and Ethylene glycol flow inside the channels. A validated numerical model is developed using a commercial computational fluid dynamics (CFD) code to investigate the effect of inlet temperatures and mass flow rates of cooling fluid and volume fraction of nanoparticles on heat transfer coefficient, pressure drop, index of uniform temperature (IUT), and performance evaluation criteria (PEC). The results demonstrated that the reverse configuration of the Tesla valve (CASE E) experienced outstanding uniform thermal distribution while the heat transfer coefficient increased by 15% in this case compared to the straight-line cooling channel. The Ag–MgO hybrid nanoparticles showed better thermal performance than the two other nanoparticles with a 4% reduction in temperature difference in the cooling plate.

Effects and optimization of airflow on the thermal environment in a data center

In this research, the escalating energy consumption challenges in data centers are addressed by optimizing airflow organization designs. Through the use of computational fluid dynamics (CFD) simulations, three different airflow strategies were evaluated and improved: underfloor precision air conditioning, inter-column air conditioning, and backplane air conditioning. These cooling systems, which are usually considered in isolation, were compared in a comprehensive manner to get a full picture of their efficiency and effectiveness. The findings reveal that the implementation of cold aisle containment (CAC) or hot aisle containment (HAC) significantly improves air supply efficiency (ASE) and reduces the supply heat index (SHI), leading to a more uniform temperature distribution and enhanced cooling performance. Specifically, the ASE increased from 65.69% to 85.57% and 90.25% for underfloor precision air conditioning and from 71.29% to 92.16% and 92.17% for inter-column air conditioning, with corresponding reductions in SHI. The backplane cooling system offered consistent ambient temperatures throughout the room, eliminating thermal hotspots without the need for aisle containment. This study offers a comparative analysis of different airflow organization schemes, highlighting the benefits of aisle containment in precision and inter-column air conditioning and the suitability of backplane air conditioning for high-density cooling without the need for traditional aisle separation. The results are crucial for informing energy-efficient cooling strategies in data center design and operation.

Inclusion of Hall and Ion slip consequences on inclined magnetized cross hybrid nanofluid over a heated porous cone: Spectral relaxation scheme

The cone geometry has a great significant for heat transmission in many industrial processes due to its ability to induce turbulence, enable directional flow, promote uniform temperature distribution, and offer versatility in applications. The current study aims to investigate the heat transport process of an inclined magnetized cross hybrid nanofluid over a heated porous cone under the influence of Hall and Ion slip consequences. Additionally, porous medium the flow is past under the effect of inclined uniform magnetic field and porosity of the medium is used to enhance heat transfer. The framed set of governing equations took the form of dimension free structure through appropriate transformations and then finally solved by an effective spectral relaxation method. Thermal impacts and heat transport mechanism associated with the hybrid flow is seen through different values of emerging parameters. Heat transport is seen higher with higher radiation parameters, as radiation and rising temperature are similar. Augmented values of Fr causes pressure drop in fluids which reduces the fluid motion and brings depreciation in velocity field. Eckert number also boosts the temperature of the fluid stirring via a porous rotating cone.

Modification of steel slag to prepare chlorides based composite phase change materials with shape stability for high-temperature thermal energy storage

Using steel slag to prepare high-temperature (>500 °C) PCMs was an effective way to achieve its high value-added utilization as a potential heat storage medium in a variety of applications, such as solar energy storage, power peak shaving, and industrial waste heat recovery. However, the complex solid waste of steel slag might be corrosive to salt-based PCMs at high temperature. To address this issue, steel slag was firstly modified with another solid waste (i.e., CFA), which was then used to microencapsulate NaCl-KCl to prepare shape-stabilized C-PCMs in this work. Thermophysical and mechanical properties of C-PCMs were analyzed. Results showed that CFA modification greatly improved chemical compatibility between steel slag and eutectic salt through phase reconstruction. Steel slag modified with 30 wt% CFA at 1100 °C was identified as the optimum skeleton. The prepared C-PCMs containing 50 wt% salt showed a phase transition temperature of 653 °C with a high latent heat of 139 J/g and an excellent cycling stability. Additionally, its thermal conductivity reached 1.46 W/(m·K), 180 % higher than of pure salt. Compressive strength of the composite could be as high as 119 MPa, superior to other salt-based C-PCMs. A heat storage device was further designed to allow the numerical investigation of thermal performance of the prepared C-PCMs in practical conditions. Attributed by reasonable arrangement of bricks, the heat storage device possessed a uniform temperature distribution over the vertical cross-section of HTF, which contributed to a quick completion of charging and discharging process. This work could potentially lay a foundation for application of steel slag in the field of high-temperature thermal energy storage.

A Simulation Study of Hybrid Solar Drying Chamber for Agriculture Product

Hybrid solar drying chamber is an application that is widely used today for agriculture products because it can promise the hygiene of the product. However, drying chambers nowadays still lack uniformity in drying products within a drying chamber, leading to food wastage and compromised product quality. This study aims to design an innovative hybrid solar drying chamber system and investigate the uniformity of temperature and velocity within the chamber using Computational Fluid Dynamics (CFD). The methodology involves validating the simulation results by comparing them with existing journal data, with a validation error of less than 5%. A new design is proposed after the validation process, considering factors such as tray arrangement and air inlet size. The results show that a tray arrangement with 0.20 m spacing between each tray provides better uniformity in temperature and air velocity distribution compared to other arrangements. Additionally, an inlet size of 0.05 m2 demonstrates the most suitable temperature distribution for drying purposes, falling within the ideal range of 318 K to 343 K. The study showed that the performance of the drying chamber under different operating conditions has consistent temperature distribution and is suitable for uniform drying. Overall, the proposed hybrid solar drying chamber system offers improved temperature control and uniformity for effective drying process.

A conjugate heat transfer investigation of outer-wall cooling performance in double-wall vane pressure side

Double wall cooling has significant potential for high-pressure turbine vane cooling technology. Geometric parameters of the double-wall vane play a crucial role in determining the cooling performance. This paper presents a double-wall cooling model with five outer wall thicknesses and three injection angles, using the curvature of the actual pressure side of the engine as a reference. The overall cooling effectiveness is investigated over the range of blowing ratio from 0.5 to 2.5. Results indicate that, at injection angles of 20° and 30°, an outer-wall thickness of 1.5D f maximizes the combined benefits of film cooling and thermal conductivity in solid domains. At an injection angle of 40°, the blowing ratio becomes a determining factor in selecting the optimal outer wall thickness. Additionally, a reasonable arrangement of pin fins promotes a more uniform outer wall temperature distribution. A thinner outer wall at higher blowing ratios provides optimum overall cooling effectiveness.

Experimental analysis of the performance of cooling plates with different channel shapes during transient laminar refrigeration

There are numerous applications in which the proper operation of cooling systems affects the performance and the durability of electronic devices. The temperature distribution throughout the units and its maximum value severely affects their operation. Flat metallic plates with an inner channel through which a coolant flows are a suitable solution for refrigerating these devices. Five different channel shapes, considering both traditional and novel configurations, were experimentally tested for transient cooling operation in a laminar flow regime. The effect of the fluid velocity on the refrigeration capacity was studied for Reynolds numbers ranging from 750 to 2000. In addition, the pressure drop of the fluid circulating along the channel for each configuration was measured as a function of the Reynolds number. For a fair comparison between the different channel shapes, the pressure drop was used to determine the pumping power required to pump the coolant, analyzing the effect of the channel shape for equal values of the pumping consumption. A novel configuration, the cruciform channel shape, provided the most uniform temperature distribution, increasing the homogeneity of the plate temperature by 19–26% and reducing the refrigeration time by 9–13% compared to the traditional configurations.

Bionic-response surface combination optimization method for latent heat storage performance improvement

Improving the melting and solidification rate of phase change material is crucial for enhancing the charging or discharging power of a latent heat storage system. This research proposed a novel two-tube heat exchanger latent heat storage unit with longitudinal fins of horsetail stem based on the bionic structure of horsetail stem cross-section. Numerical modeling of transient melting of phase change material in horsetail stem fins by natural convection was established. The model’s accuracy was verified and compared with horsetail stem fins and conventional straight fins. Moreover, we optimized and designed the new fin structure based on the response surface method with minimum melting time as the objective function. The optimization results show that the optimized ponytail fins have a more uniform temperature distribution of the phase change material, significantly eliminating the influence of the heat transfer hysteresis zone, and reaching the steady state more quickly under the heat storage condition. Compared to straight fins, optimized horsetail stem fins reduced the heat storage area by only 3.80% and shortened the phase change material melting time by 44.30%. The solidification time was also reduced by 54.59%. This study provides a new idea for the structural design of phase change heat storage fins.

Experimental study on preheating and salt circulation performance of a single receiver tube based on induction heating

The design of a light source for a molten salt receiver experimental system has become challenging owing to the complex heating characteristics of the half-circumference surface during operation. Electromagnetic induction heating is an innovative technology that can replicate a half-circle heating scenario. However, its feasibility must be verified. In this study, we constructed a single receiver tube experimental system using induction heaters and developed a 3D numerical model coupling electromagnetic field to analyze the tube temperature distribution and molten salt temperature rise during preheating and salt circulation, considering various parameters. The results indicated that the numerical simulation agreed well with the experimental results, and the induction heater successfully reproduced the half circumference heating scenario. During preheating, a lower heat flux and higher wind speed result in a more uniform temperature distribution along the circumference of the tube wall, facilitating comprehensive preheating. During salt circulation, the heat flux and inlet salt mass flow significantly affected the temperature of the tube wall but had a relatively small effect on the back-side wall. Wind speed had the opposite effect, which was related to the arrangement of the experimental site. A higher heat flux, lower wind speed, and higher inlet salt mass flow led to a higher temperature increase in the molten salt.

Experimental investigation on frosting performance of a microchannel heat exchanger in heat pump system for electric vehicles

Frosting of outdoor heat exchangers deteriorates the heat transfer performance of the electric vehicle (EV) heat pump system. This study conducted frost experiments on the outdoor heat exchanger of an EV heat pump air-conditioning system, considering different flow configurations, tube arrangements, and frontal air volume. The purpose of the study was to establish the optimal tube arrangements and flow configurations for minimizing frost formation and maximizing system performance. The results indicate that a three-flow configuration outperforms a two-flow setup under frosting conditions. Specifically, a flow sequence of 14-21-35 increases the heat capacity by 15.05 %–20.64 % compared to that of the reverse flow order of 35-21-14. The flow sequence a-b-c represents the number of flat tubes along the refrigerant flow process. Additionally, the coefficient of performance (COP) increases by 1.19 %–3.55 %. Higher airflow reduces frost formation. A significant correlation exists between the refrigerant distribution within the heat exchanger and the corresponding frost distribution on the surface of the microchannel heat exchanger. The frost formation rate was slower for the flat tube vertical arrangement. Furthermore, horizontal tube arrangements were more conductive than vertical ones, providing a more uniform temperature distribution and higher heat transfer rates (an increase of up to 2.7% in heat transfer and 3.4% in heat capacity). The COP of the vertical arrangement was consistently higher than that of the horizontal arrangement by 1.4 %–3 %.

Kriging surrogate model for optimizing outlet temperature distribution in low-emission combustors without dilution holes

Designing advanced combustors that operate at high temperatures and produce little pollution, especially in the absence of primary and dilution holes, is a difficult task that may bring significant challenges. In this regard, this paper introduces a Kriging surrogate model approach to optimize the outlet temperature distribution of the combustor to achieve such advanced low-pollution combustors. Building upon previous research, this study explores the effects of the swirler blade installation angle on the outlet temperature distribution of the combustor without primary or dilution holes. Traditional methods, such as the control variable method using computational fluid dynamics (CFD) for numerical simulation, are limited in application due to the complex coupling of flow, heat transfer, mass transfer, and combustion processes. In contrast, surrogate models, especially the Kriging model, offer a rapid and efficient alternative to extensive CFD simulations that provide accurate predictions and error estimates for the solution of the problem. In summary, this paper details the process of generating sample points through three-dimensional numerical simulations, develops a Kriging surrogate model through Latin hypercube sampling, and optimizes the model to identify the most uniform outlet temperature distribution achievable by adjusting the installation angle of the swirl blade. The optimal design parameters, which are quickly obtained through the Kriging model, showed a significant reduction in the overall temperature distribution function and the radial temperature distribution function by 21% and 27.14%, respectively.

Heat transfer optimisation using novel biomorphic pin-fin heat sinks: An integrated approach via design for manufacturing, numerical simulation, and machine learning

With the availability of advanced manufacturing techniques, non-conventional shapes and bio-inspired/biomorphic designs have shown to provide more efficient heat transfer. Consequently, this research investigates the heat transfer performance and fluid flow characteristics of novel biomorphic scutoid pin fins with varying volumes and top geometries. Numerical simulations were conducted using four hybrid designs for Reynolds Number 5500–13500. The impact of pin fin 'top' geometrical features on the heat transfer coefficient (HTC) was evaluated by combining computational fluid dynamics (CFD), experimental data, and machine learning. The results highlighted that the new pin fins saved 6.3 % to 14.3 % volume/material usage but produced around 1.5 to 1.7 times more heat transfer than conventional square/rectangular fins. Also, manipulating pin fins via the top geometrical properties can lead to more uniform velocity and temperature distributions while demonstrating the potential for increased thermal efficiency with reduced thermal resistance. Furthermore, six machine learning models accurately predict HTC using volume and surface area as key variables, achieving less than 5 % mean absolute percentage error (MAPE). Overall, this research introduces innovative biomorphic designs with unconventional geometries, emphasising resource optimisation and efficient HTC prediction using machine learning. It simplifies design processes, supports agile product development, calls for re-evaluation of conventional heat sink geometries, and provides promising directions for future research.

Numerical study on improved mass and heat transfer performance in a solid oxide electrolysis cell with sine wave flow field

In this paper, the periodic variation of sine wave is used to promote the transport and diffusion process of reactive gases; and the relationship between the performance of a solid oxide electrolysis cell (SOEC) and the mass and heat transfer capabilities of its flow field is thoroughly examined. The impact of variations in the amplitude and frequency of the sine wave on the SOEC's electrolysis efficiency, its mass and heat transfer properties, and fluid flow dynamics are explored. The results indicate that longitudinal flow velocity of the gas in the sine wave flow channel is increased by 26.96–80.76% at a current density of 10000 A/m2, and this kind of flow channel exhibits superior gas transport performance. Moreover, the temperature-uniformity index and the maximum thermal stress of the positive-electrolyte-negative (PEN) structure are decreases by 18.93–22.67% and 20%, respectively. It indicates that this configuration is capable of reducing thermal stress and enhancing the uniformity of temperature distribution at high current-densities. Increasing the amplitude and frequency improves the comprehensive performance of the flow field. More specifically, frequency has a greater impact on flow field performance than amplitude.

Experimental study on moisture diffusivity, activation energy, and mathematical modeling of drying kohlrabi under different solar drying methods

AbstractThe assessment and enhancement of any drying system for optimal drying processes relies on critical parameters, namely moisture diffusivity and activation energy. In this study, medicinally beneficial kohlrabi of 40‐mm diameter and 6‐mm thickness samples were dried under three different drying methods, namely open sun drying (OSD), natural air‐circulation mode (NACM) single slope direct solar dryer (SSDSD), and forced air‐circulation mode (FACM) SSDSD. The experimental results showed that the drying chamber operating temperature and air velocity played significant roles in the moisture diffusion process and activation energy required to dry the kohlrabi sample. The FACM exhibited the highest average moisture diffusivity values at 7.29 × 10−10 m2/s, surpassing both NACM (5.65 × 10−10 m2/s) and OSD (3.28 × 10−10 m2/s). The activation energy needed for the drying process was the lowest in FACM at 27.44 kJ/mol, followed by NACM at 31.37 kJ/mol and OSD at 35.29 kJ/mol. This is due to the uniform temperature distribution and high airflow rate in the case of FACM. Additionally, 10 thin‐layer models were tested for all three experimental conditions. The statistical analysis showed that for OSD and NACM, the Midilli et al. model, and for FACM, the Page model was best suited for representing drying kinetics with lowest χ2 and root mean square error and highest R2 values. Furthermore, the energy and exergy assessment guaranteed an evaluation of the solar drying system's efficiency.Practical applicationsThis research provides valuable insights into optimizing solar drying methods for kohlrabi preservation. Understanding how temperature and air velocity influence moisture diffusivity and activation energy allows practitioners to enhance drying efficiency. Forced air‐circulation mode (FACM) single slope direct solar dryer (SSDSD) emerges superior, with higher moisture diffusivity and lower activation energy. The study also identifies appropriate drying kinetics models for each method, aiding the accurate prediction of drying behavior. Emphasizing efficiency, the research highlights FACM's superior thermal efficiency and natural air‐circulation mode's higher exergetic efficiency. These insights empower practitioners to make informed decisions, potentially improving agricultural product preservation, reducing energy consumption, and promoting sustainability. Moreover, the research's findings hold significant implications for industrial food processing and preservation applications, suggesting the direct implementation of optimized solar drying techniques in large‐scale settings for kohlrabi and similar agricultural products.

Strain rate and temperature rate behavior of ultra-high-strength 1770 steel: Base for transverse impact analysis

The investigation was motivated by the widespread use of ultra-high-strength steels in cable-stayed bridges and armor steel plates. These structures are exposed to elevated risks from extreme loads, including vehicle impacts and blast loadings. The study aimed to investigate the mechanical properties of 1770 steel for applications in extreme conditions. The strain rates and temperatures ranged from 0.00095 s-1 to 1303 s-1 and 20°C to 900°C, respectively. Tensile tests were conducted at various strain rates using a Split Hopkinson Tension Bar for dynamic testing and a universal testing machine for quasi-static testing at room temperature (20°C). Quasi-static tension at elevated temperatures was carried out using an electromechanical testing machine coupled with a heating device. A uniform temperature distribution inside the specimens was ensured by a 30-minute holding time. The results of the tensile test indicate that the 1770 steel displays notable thermal softening effects and strain rate hardening that differ from mild steel. The standard Johnson-Cook (J-C) model was found to be inadequate in accurately predicting the strain rate effects of this specimen. To address this issue, the strain rate parameter C in the standard model was adjusted to create the modified J-C model, which demonstrated good agreement with the experimental results. To further demonstrate the modified model and the identified parameters, drop hammer impact tests and corresponding numerical simulations were conducted. The impact test and numerical simulation results showed good agreement in terms of deformation and contact force. The mechanical properties and the constitutive models can serve as a design reference for the ultra-high-strength 1770 steel in extreme envirnments, as well as a theoretical basis for fitting material models of similar ultra-high-strength steels.