Unconventional Gas Reservoirs Research Articles

Current Status of Helium Resource Research and Prediction of Favorable Areas for Helium Reservoir in China

As an unconventional oil and gas reservoir, helium gas reservoirs have gradually become a focus of attention. In recent years, with the continuous increase in demand for helium gas, the uneven distribution of global helium resources has attracted China’s attention to helium resources. In this study, a method for predicting favorable areas of helium gas was proposed based on the natural gas exploration theory and the idea of “finding gas in enrichment areas”. We conducted an in-depth study and analysis of the types of helium gas formations in China by comprehensively using geochemical and isotope-testing data, identifying the distribution of helium source rocks in China. Based on this, we conducted directed analyses of the transport channels and caprock conditions for helium gas, and summarized the enrichment modes of helium gas. Using this method, we predicted five favorable areas for the enrichment of helium gas in China, providing an important basis for the future exploration and development of helium resources in China.

Optimization of tight gas reservoir fracturing parameters via gradient boosting regression modeling

In China, the exploitation of most unconventional oil and gas reservoirs is dependent on hydraulic fracturing, which is a key method employed when developing tight gas formations. Numerous scholars and field engineers, both domestically and internationally, have conducted extensive numerical simulations and physical experiments to study crack propagation and predict post-fracturing productivity in hydraulic fracturing. Although some progress has been reported in this regard, it is difficult to accurately predict the well productivity using mechanistic models owing to the vertical multilayered development of tight gas reservoirs. In this study, vertical fractured wells in a block of Sulige gas field were examined. The block relied on hydraulic fracturing to produce tight gases. However, as development progressed, the available reservoir environment deteriorated, large differences emerged between wells after fracturing, and the fracturing results did not meet the expectations. In this study, geological, construction, and generation data for this block that had been collected since 2007 were analyzed. After applying multiple machine-learning methods to filter outliers and fill in missing values, k-means clustering, classification enhancement, extreme gradient enhancement, and LightGBM algorithms were used to establish a regression model. The analysis results revealed that the regression accuracy of the cluster test set was as high as 70% and that the LightGBM model had the best regression effect among the 227 stripper wells in the block. After optimizing the fracturing construction parameters (fracturing fluid volume, proppant volume, liquid-nitrogen volume, and pumping rate), the average fracturing fluid and liquid-nitrogen volumes per well decreased, whereas the unit reservoir proppant and liquid-nitrogen volumes increased. The results also revealed that 182 wells showed an improved initial production capacity during fracturing. The average gas production index per meter increased by 22.04%. This approach enabled rapid and efficient production forecasting and construction optimization. Moreover, this represents a novel fracture design method that is applicable to onsite engineers in tight gas production fields in the Ordos region.

Geochemical and mineralogical characterizations of Silurian “Hot” shales: Implications for shale gas/oil reservoir potential in Jeffara basin-southeastern Tunisia, North Africa

The Silurian organic-rich hot shale deposits represent the origin of 80–90% Paleozoic sourced hydrocarbons on the entire Saharan Platform. As such, it is an area of significant interest for exploring its potential as an unconventional reservoir and gaining new insights into its properties. In this study, the geochemical and mineralogical analysis of eighty-two borehole samples from three studied wells (T, B, and M) located in Jeffara Basin, in southeastern Tunisa, distributed over a depth between 1200 m and 2200 m, show that the hot shale layer has significant potentials of an unconventional shale gas reservoir. According to the rock-eval and GCMS results, the total organic carbon (TOC) of the hot shale deposits is good to great, ranging between 0.54 wt% and 23.86 wt%, and the average hydrogen index (HI) is around ∼200 mg HC/g of TOC, which indicates that the hot shales were originally rich in type II/III organic matter (OM). The thermal maturity of the preserved OM is determined by the kerogen type with values varying from 0.4% to 1%, and Tmax values reaching 460 °C in T, B, and M wells which indicate that the hot shales preserved early mature to mature OM placed within oil/gas generation window. The calculated geochemical parameters reveal an average hydrocarbon generation potential (HGP) for the three studied wells of 20.37 kg HC/ton rock. In addition, the transformation ratios (TR) in T, B, and M wells are, respectively, 21.12%, 30% and 35.25%. However, only B and M wells show a cross-over layer, with oil saturation index (OSI) exceeding 100%, with significant potential as a hydrocarbon saturated source rock, making it a considerable target for unconventional oil exploration. Relevant results of Rock-Eval, biomarkers and XRD exhibit coherent features that reflect reducing marine conditions during the lower Silurian period. Moreover, the mineralogical composition was investigated to estimate the importance of frackable mineral fractions such as quartz (∼15%) and carbonates (calcite-dolomite). Mineral brittleness index (MBI) was calculated and compared to a well-known unconventional reservoir in the Neal shale member of the Floyd shale group in the Black Warrior Basin (US), which displays moderate to low MBI. The hot shales in the study area have a considerable MBI, which could be easily enhanced by hydraulic fracturing to liberate oil/gas from the potentially saturated unconventional shale reservoir.

Geomechanical analysis of lost circulation control in tight formations

Unconventional oil and gas reservoirs, especially that in tight formations, contribute great parts to the global energy. During drilling in tight formations, lost circulation was one of the major problems, which can cause large amount of non operation time and millions of losses. In order to migrate the problem, lost circulation materials (LCMs) were used to prevent reopening of the fracture by isolating the fracture tip while the calculation of stress intensity factor (SIF) and fracture width is the key to LCMs design. In this paper, a dual porosity medium flow model suitable for tight formation is established to calculate the pressure distribution in fracture, and the fracture width and fracture reopening pressure (FROP) is then calculated by using the semi-analytical fracture mechanics model. Sensitivity analysis of critical parameters, for example, fracture length, wellbore radius, LCMs permeability, viscosity, wellbore pressure, and two rock-mechanics-related properties are implemented. The fracture width is larger in the formation with large horizontal principal stress anisotropy, low Young’s modulus and Poisson’s ratio. The increase in fracture length, wellbore radius and wellbore pressure also contributes to fracture opening. Meanwhile, we compared the situation before and after fracture plugging and the results emphasize that the fracture reopening is less likely to occur under the conditions of high viscosity and low permeability LCMs. The method proposed in this study can be used to calculate fracture width and FROP, which has potential significant application for lost circulation control in tight formation.

Mechanisms by Which an Evaporated Lagoon Sedimentation System Controls Source–Reservoir Preservation in Lei32 Sub-Member Unconventional Oil and Gas

The muddy limestone in the Lei32 sub-member of the Middle Triassic Leikoupo Formation in the well Chongtan 1 (CT1) of the Sichuan Basin has yielded promising industrial oil and gas production. This discovery has the potential to become a significant strategic reservoir in the future for oil and gas exploration in the Sichuan Basin. However, the understanding of hydrocarbon accumulation in the muddy limestone of the Lei32 sub-member remains insufficient, which poses limitations on further exploration selection and deployment strategies. This study focuses on the analysis of core samples and laboratory data in the wells CT1 and Jianyang 1 (JY1), aiming to investigate the source rock and reservoir characteristics of the muddy limestone in the Lei32 sub-member, as well as the primary controlling factors influencing the development of the source rock and reservoir. The results show that the Lei32 sub-member in the Central Sichuan Basin is an evaporated lagoon deposition; the tight argillaceous limestone and limy mudstone exhibit the characteristic of source–reservoir integration, belonging to a new type of unconventional oil and gas reservoir. The reservoir space of the argillaceous limestone and limy mudstone in the Lei32 sub-member primarily consists of inorganic and organic micro–nanopores and microfractures. The average porosity and permeability are 2.7% and 0.19 mD, indicating a low-porosity and low-permeability unconventional reservoir. The clay minerals and gypsum content are the important factors influencing reservoir porosity, and the fractures are key factors influencing permeability. This study will elucidate the specific features of hydrocarbon accumulation in the muddy limestone reservoirs of the Lei32 sub-member and provide insights into its exploration potential.

Research on Fluid–Solid Coupling Mechanism around Openhole Wellbore under Transient Seepage Conditions

Hydraulic fracturing is one of the most important enhanced oil recovery technologies currently used to develop unconventional oil and gas reservoirs. During hydraulic fracture initiation, fluid seeps into the reservoir rocks surrounding the wellbore, inducing rock deformation and changes in the stress field. Analyzing the fluid–solid coupling mechanism around the wellbore is crucial to the construction design of fracturing technologies such as pulse fracturing and supercritical carbon dioxide fracturing. In this study, a new transient fluid–solid coupling model, capable of simulating the pore pressure field and effective stress field around the wellbore, was established based on the Biot consolidation theory combined with the finite difference method. The numerical results are in excellent agreement with the analytical solutions, indicating the reliability of the model and the stability of the computational approach. Using this model, the influence of seepage parameters and reservoir properties on the fluid–solid coupling around the open-hole wellbore was investigated. The simulation results demonstrate that, during wellbore pressurization, significant changes occur in the pore pressure field and effective stress field near the wellbore. The fluid–solid coupling effect around the wellbore returns to its initial state when the distance exceeds four times the radius away from the wellbore. As the fluid viscosity and wellbore pressurization rate decrease, the pore pressure field and effective circumferential stress (ECS) field around the wellbore become stronger. Adjusting the fluid viscosity and wellbore pressurization rate can control the effect of seepage forces on the rock skeleton during wellbore fluid injection. For the same injection conditions, rocks with q higher Young’s modulus and Poisson’s ratio exhibit stronger pore pressure fields and ECS fields near the wellbore. This model furnishes a dependable numerical framework for examining the fluid–solid coupling mechanism surrounding the open-hole wellbore in the initiation phase of hydraulic fractures.

Discovery of Pseudomorph Scapolite and Diagenetic Indication from the Permian Volcaniclastic Rocks in Western Sichuan (SW China)

Volcaniclastic rocks are important unconventional oil and gas reservoirs from which it is difficult to determine the protolith due to strong metasomatic alteration. Intensive alteration has occurred in much of western China, but few robustly documented examples are known from which to assess the alteration processes. Further recognition from the petrological and mineralogical record is essential to quantify the diagenetic environment, the degree of alteration, and its impacts. Permian volcanic rocks are widely developed in the western Sichuan Basin (southwestern China), with a thickness of more than 200 m. The thickness of volcaniclastic rocks in the Permian Emeishan Basalt Formation is up to 140 m, with a 5600~6000 m burial depth. In this study, we demonstrate an approach to recognizing hydrothermal alteration by the occurrence of scapolite megacryst mineral pseudomorphs (SMMPs) in Permian volcaniclastic rocks in the Sichuan Basin (southwestern China). The results show that SMMPs in the Permian volcaniclastic rocks in the western Sichuan Basin mainly occur in the lower part of the Permian basalts as intragranular minerals and rock inclusions. Scapolite is transformed into quartz and albite, and only the pseudomorph is preserved, indicating secondary hydrothermal fluid metasomatic alteration. Scapolite is formed after microcrystalline titanite and is the product of the high-temperature pneumatolytic metasomatism of plagioclase from the mafic protolith during the post-magmatic stage. The mixing of meteoric water and barium-rich hydrothermal fluid leads to the precipitation of barite; additionally, the pores are filled with barite and halite after the alteration of scapolite. The silicification and hydrothermal dissolution of scapolite and the albitization of sodium-rich matrix minerals increase the pore volume, which is conducive to the later recharge by hydrothermal fluids. The discovery of SMMPs can serve as an indicator of the high-temperature pneumatolytic metasomatism and mixing of meteoric water and deep hydrothermal fluid.

Multi-step Fracturing Radial Boreholes for Efficient Development of Unconventional Gas Reservoirs

Multi-step Fracturing Radial Boreholes for Efficient Development of Unconventional Gas Reservoirs

Numerical Simulation of integrated three-dimensional hydraulic fracture propagation and proppant transport in multi-well pad fracturing

Multi-well pad fracturing is an indispensable technology for the sustainable development of unconventional oil and gas reservoirs, but the integrated simulation of fracture propagation and proppant migration in massive fracturing treatments remains challenging, including complicated numerical implementations and computational bottlenecks due to its multi-physics, fracture front propagation, size differences between proppant particles and hydraulic fractures. In this work, an integrated model of fracture propagation and proppant migration in multi-well pad fracturing was established based on the three-dimensional discontinuous displacement method for fracturing deformation computations and the Eulerian-Eulerian framework for capturing proppant concentration. The proposed simulator not only accounts for key physical processes such as stress shadow, dynamic flow rate distribution in the wellbore, fluid leak-off, perforation erosion, fractures evolution, proppant bridging, and gravitational settling, but also couples the simulation of 3D planar propagating fractures and proppant transport at well-pad scale, and presents excellent computational efficiency and promising applications than conventional fracturing models. To explore the fracture geometries and proppant distribution in typically stacked layers, single-well, multi-lateral wells, and multi-well pad fracturing are simulated from simple to complex. The findings showed that fracture propagation is jointly affected by intra-stage, inter-stage, and inter-well stress interference mechanisms, and fracture geometries are characterized by unevenness, asymmetry, and heel bias. Proppant transport is controlled by the fracture width and geometries, and most of the proppant is concentrated near the wellbore area and bridging at the narrow fractures. Fracture geometries and proppant distribution are sensitive to the landing locations of horizontal wells because hydraulic fractures always grow in the path of least resistance. Although close lateral well-spacing is beneficial to improve the stimulation efficiency, there are some challenges such as overlapped SRV, enhanced inter-well interference, and severe fracturing hits. Compared with the layout of stacked wells, staggered wells are not only beneficial to reduce the vertical inter-well interference, but also improve reservoir stimulation efficiency. Overall, the stimulated area of the high in-situ stress layers is relatively low even with intentionally landed wells.

Numerical simulation study on evolution law of three-dimensional fracture network in unconventional reservoirs

It has become a consensus that large-scale hydraulic fracturing is adopted to achieve the stimulation of unconventional oil and gas reservoir. The complex fracture network formed by fracturing is closely related to the effect of reservoir stimulation, which has extremely complicated evolution process. Therefore, it is necessary to study the evolution law of fracture network in large-scale hydraulic fracturing of unconventional reservoirs. In this article, the geological engineering parameters of horizontal well H in shale gas reservoir in southern Sichuan are taken as an example, a three-dimensional fracture network expansion model is established based on the boundary element method and finite volume method, and the simulation of the complex fracture network in a whole well section is carried out to analyze the evolution law of reservoir fracture network under different geological and engineering parameters. The results show that the horizontal stress field distribution has a significant effect on fracture geometric form. Hydraulic fractures in reservoirs with larger horizontal stress difference have stronger directivity, while the horizontal wellbore tends to obtain better reservoir stimulation results when it is parallel to the minimum horizontal principal stress setting. The conjugated natural fracture developed in the reservoir inhibits the hydraulic expansion fractures in both directions. Although it increases the complexity of the fractures, it is not necessarily conducive to improving the reservoir stimulation effectiveness. The lower the strength of natural fracture is, the more complex the fracture geometric form becomes, and the smaller the stimulated reservoir volume is. Correspondingly, the higher the strength of natural fracture is, the simpler the fracture geometric form becomes, and the larger the stimulated reservoir volume is. Suitable fracturing construction displacement can not only contribute to form a more complex fracture distribution, but also help to obtain a larger stimulated reservoir volume. The optimal construction displacement ranges from 10 to 14 m3/min. Low viscosity fracturing fluids are suitable for the formation of long-narrow fractures and able to connect with the remote reservoir and form complex fracture networks. Lower viscosity fluids can be used to achieve better reservoir stimulation effectiveness when sand-carrying capacity is met.

Comprehensive Study on Microscopic Pore Structure and Displacement Mechanism of Tight Sandstone Reservoirs: A Case Study of the Chang 3 Member in the Weibei Oilfield, Ordos Basin, China

With the continuous growth in global energy demand, research and development of unconventional oil and gas reservoirs have become crucial in the field of energy. This study focuses on the Chang 3 reservoir of the Yanchang Formation in the Ordos Basin, Weibei Oilfield, China. This reservoir is a typical tight sandstone reservoir, and its microscopic pore structure and displacement mechanism are essential for the efficient development of tight oil. However, the reservoir faces challenges such as complex microscopic pore structures and unclear displacement mechanisms, which hinder the efficient development of tight oil. In light of these challenges, through various studies including core observation, high-pressure mercury injection tests, water flooding experiments, oil-water two-phase relative permeability measurements, and stress sensitivity experiments, it was found that the Chang 3 reservoir exhibits strong microscopic heterogeneity. The pore-throat distribution characteristics mainly present two types: single peak and double peak, with the double peak type being predominant. The reservoir was classified and evaluated based on these characteristics. The improved injection ratio and properties enhance oil displacement efficiency, but an increase in irreducible water saturation has a negative impact on efficiency. The stress sensitivity of the reservoir fluctuates between weak and strong, with permeability being sensitive to net confining pressure. It is recommended to pay particular attention to the stress-sensitivity characteristics during reservoir development. The research results provide a scientific basis for the optimized development of tight oil reservoirs in this region, promote the sustainable development of unconventional oil and gas resources, and have significant theoretical and practical implications.

Nanoscale Insights into CO2 Enhanced Shale Gas Recovery in Gas-Water Coexisting Kerogen Nanopores.

The presence of water clusters in kerogen nanopores reduces the occurrence and migration of methane (CH4) and thus affects shale gas extraction. CO2 injection, as an effective approach to enhance shale gas recovery, still presents challenges in its ability to mitigate the impact of immobile water clusters within the kerogen. In this work, molecular dynamics simulations were employed to investigate the microscopic transport process of water clusters and CH4 following CO2 injection in the gas-water coexisting kerogen nanopores. The results demonstrate that CO2 can desorb irreducible water clusters to dredge the pores while extracting CH4, enhancing gas-water mobility, and shale gas recovery by transitioning the wettability of the kerogen nanopore surface from weakly water-wet to CO2-wet. The impact of CO2 on the wettability of kerogen surfaces is primarily manifested in two aspects: CO2 can intrude the interface between water clusters and kerogen to reduce the number of hydrogen bonds between them, resulting in the detachment of water clusters; and the surface of kerogen nanopores can form a layer of CO2 gas film, which prevents desorbed water clusters and CH4 from readsorbing onto the wall surface. This study provides important insights in enhancing the understanding of the microscopic mechanisms in nanoscale flow, as well as for the development of an unconventional gas reservoir.

Variations of sedimentary environment under cyclical aridification and impacts on eodiagenesis of tight sandstones from the late Middle Jurassic Shaximiao Formation in Central Sichuan Basin

Understanding eodiagenesis is essential to decoding the diagenetic pathways of tight sandstones that act as excellent unconventional oil & gas reservoirs. Great paleoclimate change is capable of influencing eodiagenetic processes of tight sandstones through variations of sedimentary environment. However, it is less noted how climate gradients between the greenhouse and the hothouse conditions impact the eodiagenesis of tight sandstones. We examined eodiagenetic processes that has been operated in the Shaximiao Formation sandstones using petrographic observation, scanning electron microscopy, geochemistry, and XRD analysis to reveal impacts of the transitional climate changes on the differential eodiagenesis and implications for the diagenesis-porosity evolution. Based on sequence stratigraphy, the Shaximiao Formation is divided into four sub-members SXM1, SXM2, SXM3, and SXM4, respectively. Dark sandstones and mudstones mainly occurred in the SXM1 and the SXM2. Grey-green clastic rocks are dominant in the SXM3, whereas red mudstones frequently appear in the SXM4. Paleoclimate indices denote that a cyclical aridification from the warm-humid to hot-semiarid conditions took place from the SXM1 to the SXM4. It could have been caused by the megamonsoon effect and the paleogeographic shift along with the breakup of the Pangaea supercontinent. Combined with the migration of depocenters, the paleoclimate change resulted in transformation of sediment provenances from mafic igneous rocks to quartzose sedimentary rock along with the decreasing textural maturity. Therefore, sedimentary environments varied from the high-saline to low-saline and from low-oxygen to high-oxygen conditions respectively, which had a crucial impact on eodiagenetic cements which were formed in the Shaximiao Formation. Chlorite and laumontite cement precipitation was promoted by high-saline alkaline fluids. Chlorite proportions show an arched trend from the SXM1 to the SXM4, compatible with those of primary and secondary porosities. In contrast, laumontite proportions exhibit a decreasing variation from the SXM1 to the SXM4. High percentages of early cements are favorable to improving resistance to the compaction and preservation of primary pores. However, high chlorite (>5%) and laumontite (>10%) proportions are destructive for the reservoir quality. Large quantities of laumontite cements occupy primary pores and impede diagenetic fluids flowing and are not favorable to the dissolution. By contrast, an excess of chlorite cements can be dissolved to produce secondary pores during the organic acid release. Thus, the SXM2 is potential as a reservoir for oil & gas. Therefore, those eodiagenetic cements can control the late diagenetic evolution and the reservoir quality. Observations made here have implications for understanding tight sandstone reservoirs elsewhere in the world.

Numerical simulations of proppant transportation in cryogenic fluids: Implications on liquid helium and liquid nitrogen fracturing for subsurface hydrogen storage

The over dependence on fossil fuels for human energy requirements together with the resultant adverse environmental effects in the form of greenhouse gas discharges has redirected our attention towards renewable energy sources. Researchers have identified hydrogen, a non-carbonaceous energy source holding the capacity to substitute fossil fuels, as a viable fuel option that has the potential to be generated utilizing eco-friendly techniques. Studies have identified underground sites that are operational or have the potential to be used for hydrogen storage. Shale formations, characterized by their low permeability, offer promising opportunities for underground hydrogen storage. These formations require stimulation techniques to generate flow channels. Pumping frac-fluid into these formations at high pressure induces fractures in them and the engineered fractures are supported by the proppants injected along with the fluid. Propped fractures form a vital conduit in unconventional gas reservoirs, which are a potential medium for storage of hydrogen. Cryogenic fracturing is an innovative approach that aims to enhance and broaden the capabilities of conventional hydraulic fracturing processes. The transmission and settlement of proppants are influenced by certain critical aspects including their density, size and volume fraction and fluid velocity, which are investigated in this contribution. This study incorporates water and cryogenic fluids like liquid nitrogen (LN2) and liquid helium (LHe) as fracturing fluids. The primary objective of this effort is to analyze proppant transportation phenomenon and the key influential factors in LN2 and LHe. The proppant volume fraction contour, equilibrium dune level (EqDL) and dune height (EqDH) data are illustrated in this research for better understanding of proppant migration. It was observed that when the fracturing fluid is given a higher velocity, the proppant grains experience increased drag force, causing them to penetrate deeper into the fracture. The desired range of proppant volume fraction for improved grain transmission was determined as 0.45 to 0.50 and the critical proppant density that significantly affected the EqDL as 187.2839 lb/ft3.

Study on Fracture Propagation Rules of Shale Refracturing Based on CT Technology

Reactivating oil and gas wells, increasing oil and gas production, and improving recovery provide more opportunities for energy supply especially in the extraction of unconventional oil and gas reservoirs. Due to changes caused by well completion and production in pore pressure around oil and gas wells, subsequently leading to changes in ground stress, and the presence of natural and induced fractures in the reservoir, the process of refracturing is highly complex. This complexity is particularly pronounced in shale oil reservoirs with developed weak layer structures. Through true triaxial hydraulic fracturing experiments on Jimsar shale and utilizing micro-CT to characterize fractures, this study investigates the mechanisms and patterns of refracturing. The research indicates: (1) natural fractures and the stress states in the rock are the primary influencing factors in the fracture propagation. Because natural fractures are widely developed in Jimsar shale, natural fractures are the main influencing factors of hydraulic fracturing, especially in refracturing, the existing fractures have a greater impact on the propagation of secondary fracturing fractures. (2) Successful sealing of existing fractures using temporary blocking agents is crucial for initiating new fractures in refracturing. Traditional methods of plugging the seam at the root of existing fractures are ineffective, whereas extensive injection of blocking agents, forming large “sheet-like” blocking bodies in old fractures, yields better sealing effects, promoting the initiation of new fractures. (3) Moderately increasing the pumping rate and viscosity of fracturing fluid is advantageous in forming “sheet-like” temporary blocking bodies, enhancing the complexity of the network of new fractures in refracturing. (4) When there is a high horizontal stress difference, after sealing old fractures, the secondary hydraulic fractures initiate parallel to and extend from the old fractures. In cases of low horizontal stress difference, the complexity of secondary hydraulic fractures increases. When the horizontal stress changes direction, the secondary hydraulic fractures also change direction. It is recommended to use high-viscosity fracturing fluid and moderately increase the pumping rate, injecting blocking agents to seal old fractures, thereby enhancing the complexity of the network of refracturing. These findings provide important technical guidance for improving the efficiency of shale oil reservoir development.

Main Control Factors of Fracture Propagation in Reservoir: A Review.

The fracture distribution and internal control factors after the fracturing of unconventional oil and gas reservoirs determine the reservoir reforming effect to a large extent. Based on the research of global scholars on the influencing factors of fracture propagation, comprehensive theoretical model, and numerical simulation, this Review systematically discusses the influence of internal geological factors and external engineering factors of unconventional oil and gas reservoir on fracture propagation behavior and summarizes the current problems and development trends in fracture research. The results show the following: (1) The fracture propagation is a comprehensive process constrained by lithology and mineral composition, water saturation, nonhomogeneity, natural weak surface, and ground stress. (2) External engineering factors have a meaningful control effect on fracture propagation; the type and temperature of fracturing fluids can also change the mechanical properties of different rocks, thus affecting the fracture propagation pattern. (3) The existing fracture propagation models have certain limitations, and their computational reliability still needs to be further verified. (4) Numerical simulation can break through the limitations of physical simulation, but different simulation methods have different shortcomings and applicability. In the future, we should focus on: (1) finding parameters to quantitatively characterize heterogeneity at the 3D level, which is an important direction to study the effect of heterogeneity on fracture propagation; (2) introducing computerized methods to establish a geological model that considers multiple factors and combining it with numerical simulation software to study fracture propagation; (3) considering the characteristics of fluid-liquid-solid phase comprehensively, establishing a suitable THL coupling equation; (4) how the interaction mode of fracturing fracture is combined with the natural fracture geometry, and how the fracture is affected by fracturing engineering parameters such as fluid injection rate and viscosity of fracturing fluid; and (5) geology-engineering dynamic integration, which is an important direction to be carried out in the future.

Establishment and application of propped hydraulic fracture conductivity theoretical model based on fracturing efficiency index

Hydraulic fracturing technology is a key technology for the development of unconventional oil and gas reservoirs, and the conductivity of hydraulic fractures has a great impact on their production. The paper introduces the "fracturing efficiency index" as means of characterising the dynamic relationship between hydraulic fracture expansion and proppant filling. It also suggests a way to figure out the proppant fracture inflow capacity. This approach addresses issues such as uneven fracturing fluid dosage, a wide range of injection discharges, and inconsistent sand spreading concentration encountered during fracturing operations. Based on this model, the influencing factors of the flow-conducting capacity such as proppant particle size, sand spreading concentration, liquid injection displacement, and proppant crushing rate, were analyzed, and the calculated results of this model are closer to the experimental results of the API flow-conducting capacity test compared with the calculated results of the reference model. Finally, this model was used to optimize the fluid volume, sand volume, and displacement of hydraulic fracturing in the Jiping 1H shale gas field. The research results show that: (1) the fracturing efficiency index is negatively correlated with the conductivity of hydraulic fractures, whereas is positively correlated with the enhancement of conductivity; (2) our model is applicable to the calculation of supported fracture inflow capacity for high sand concentration, large particle size, intermediate fracture flow and low crushing rate, and the results are close to more than 98.58%, 98.29%, 95.68% and 95.08% of the experimental results, respectively; (3) On-site hydraulic fracturing does not result in higher production capacity with more fracturing fluid dosage, higher displacement and more sand addition; there are optimal fluid, optimal displacement and optimal sand intervals, which are optimized to increase production by 26.92%. It can be seen that the hydraulic fracture conductivity model can optimize various parameters of on-site fracturing construction.

Sequence stratigraphy of the Eocene deep-water organic-rich mudstones in the Fushun Basin, Northeast China

Sequence stratigraphy study in mudstone and oil shale strata is difficulty but critical for the analysis of the quality unconventional oil and gas reservoirs. This contribution investigates the sequence stratigraphy of the Eocene thick organic-rich fine-grained sediments in the Fushun basin, according to the organic geochemical data measured in laboratory and predicted by the amplitude difference the resistivity and the density curve when they are overlapping (which was called ΔlogR). The sampling interval of ΔlogR was 0.125 m. The results show that the total organic carbon, the oil yield, and the petroleum potential of the Eocene mudstones prove a good linear correlation between values measured in lab and values predicted by the ΔlogR model. A total of 21 parasequences are identified in mudstones and can be divided into two cycles, a fully developed lower cycle and an underdeveloped upper cycle. There are four organic matter accumulation stages in a fully developed cycle, including two stages in the uprising half-cycle characterized by low values and rising values of the predicted geochemical data, respectively, followed by two stages in the declining half cycle characterized by high values and decreasing values of the predicted geochemical data, respectively. This contribution provides a basis for a further analysis of the characteristics of organic matter cycles in the oil shale strata of the Fushun Basin and areas with similar situation.

Application and Research Progress of CO2 Stimulation Technology in Unconventional Oil and Gas Reservoirs: A Review and Prospect

Application and Research Progress of CO₂ Stimulation Technology in Unconventional Oil and Gas Reservoirs: A Review and Prospect

Optimization of fracturing stages/clusters in horizontal well based on unsupervised clustering of bottomhole mechanical specific energy on the bit

Multi-cluster perforation and multi-staged fracturing of horizontal well is one of the main technologies in volumetric fracturing stimulation of unconventional oil and gas reservoirs, but unconventional reservoirs in China are generally of strong heterogeneity, which causes different fracture initiation pressures in different positions of lateral, making it difficult to ensure the balanced fracture initiation and propagation between clusters in multi-cluster perforating. It is in urgent need to precisely evaluate the difference in rock strength in lateral and determine the well section with similar rock strength to deploy fractures, so as to reach the goal of balanced stimulation. Based on the drilling and logging data, this paper establishes an unsupervised clustering model of mechanical specific energy of bit at the bottomhole the lateral. Then, the influence of drill string friction, composite drilling and jet-assisted rock breaking on the mechanical specific energy is analyzed, and the distribution and clustering categories of bottomhole mechanical specific energy with decimeter spatial resolution are obtained. Finally, a fracture deployment optimization method for horizontal well volumetric fracturing aiming balanced stimulation is developed by comprehensively considering inter-fracture interference, casing collar position, plug position, and clustering result of bottomhole mechanical specific energy. The following results are obtained. First, compared with brittleness index, Poisson's ratio and stress difference, perforation erosion area is in a stronger correlation with the mechanical specific energy, and the mechanical specific energy can effectively characterize the difference in the amount of proppant injected into the perforation clusters in the lateral, so it can be served as one of the important indicators for the selection of fracture deployment position. Second, the drilling and logging data cleaning and smoothing and the clustering number selection by the elbow method are the key steps to obtain the clustering results of bottomhole mechanical specific energy, which can tell the difference in the mechanical specific energy with decimeter-level resolution. Third, the interval with mechanical specific energy within 10% of the average value in the section is selected for deploying perforation clusters, and the compiled computer algorithm can automatically determine the optimal position of fracturing section and cluster, so as to realize the differential design of stage spacing and cluster spacing. In conclusion, the research results can further improve the fractures deployment efficiency and balanced stimulation of volumetric fracturing in unconventional oil and gas reservoirs, and this technology is expected to provide ideas and new methods for the fracture deployment optimization of horizontal well volumetric fracturing in unconventional oil and gas reservoirs.