Unbonded Length Research Articles

Deflection and Crack-Width Prediction of Partially Boned CFRP Concrete Beams

Concrete beams reinforced with fiber reinforced polymer(FRP)bars exhibit large deflections and crack widths as compared to concrete beams reinforced with steel due to the low modulus of elasticity of FRP. Consequently,in many cases,serviceability requirements may govern the design of such members. This paper describes six partial bonded concrete beams prestressed with CFRP tendons are tested under monotonic loads. deformation and crack width of this kind of beams with varying unbonded length are systematically investigated. The predictions of the 《Code for Design of Concrete Structures》（GB50010－2002）equations are compared with the experimental results obtained by testing six partial bonded concrete beams prestressed with CFRP tendons. Good agreement was shown between the theoretical and the experimental results.

Effect of Partial Unbonding on Prestressed Near-Surface-Mounted CFRP-Strengthened Concrete T-Beams

The flexural behavior of RC T-beams strengthened with prestressed near-surface-mounted (NSM) carbon fiber-reinforced-polymer (CFRP) reinforcement was investigated. The specific objective was to study the effect of partial unbonding of the CFRP reinforcement on the beam flexural behavior to increase the deformability. A total of eight RC T-beams were tested under four-point monotonic loading. The main variables were the level of prestressing force in the CFRP bars and the unbonded length at the midspan of the beam. The test results showed that all of the prestressed strengthened beams effectively improved the ultimate load-carrying capacity and the serviceability performance compared to the unstrengthened beam. The partially bonded prestressed beams exhibited an enhancement of the deformability compared to the fully bonded beams while minimizing the reduction of the load-carrying capacity. Partial unbonding was more effective to improve the deformability at higher levels of prestressing force. The general behavior of the partially bonded beams was reasonably well predicted by an analytical model developed previously by the writers.

Simplified Methodology for the Evaluation of the Residual Strength of Corroded Reinforced Concrete Beams

Steel corrosion in reinforced concrete (RC) structures leads to change of steel mechanical properties, longitudinal cracking in the concrete cover, and other related effects that weaken the serviceability and load capacity of the composites. It is therefore extremely important to have methods targeted to the evaluation of the structural damage induced by corrosion for estimating the residual load capacity of a structure, and then for inspection procedures and strengthening the maintenance interventions. This paper presents a simplified methodology capable of providing estimates of the residual life of corroded RC beams. The proposed method uses damaged material properties, and accounts for the length of partial corrosion and the amount of corrosion, concrete loss and change of bond strength within this specified length. A comparison of the model predictions with the experimental results published in the literature shows the validity of the model. It is also concluded that the ultimate flexural moment of corroded RC beam will not significantly influenced by the partially corroded or unbonded length and the bond characteristics over this partial length as long as the tensile steel of the beam can reach its yield strength. In addition, although complete loss of bond over the partial length is assumed to asses the residual strength of corrosion-damaged RC beam, neglecting the influence of bond strength within the corroded length may lead to underestimate the ultimate flexural capacity of the damaged beam, especially when the corrosion level of tensile steel of the RC beam is not very high.

Predicting the flexural capacity of RC beam with partially unbonded steel reinforcement

Due to the reduction of bond strength resulting from the high corrosion level of reinforcing bars, influence of this reduction on flexural capacity of reinforced concrete (RC) beam should be considered. An extreme case is considered, where bond strength is complete lost and/or the tensile steel are exposed due to heavy corrosion over a fraction of the beam length. A compatibility condition of deformations of the RC beam with partially unbonded length is proposed. Flexural capacity of this kind of RC beam is predicted by combining the proposed compatibility condition of deformations with equilibrium condition of forces. Comparison between the model's predictions with the experimental results published in the literature shows the practicability of the proposed model. Finally, influence of some parameters on the flexural capacity of RC beam with partially unbonded length is discussed. It is concluded that the flexural capacity of the beam may not be influenced by the completely loss of bond of the whole beam span as long as the tensile steel can yield; whether or not the reduction of the flexural capacity of the beam resulting from the loss of bond over certain length may occur depends on the detailed parameters of the given beam.

Nonlinear behavior of concrete beams with hybrid FRP and stainless steel reinforcements

The full-range behavior of partially bonded, together with partially prestressed concrete beams containing fiber reinforced polymer (FRP) tendons and stainless steel reinforcing bars was simulated using a simplified theoretical model. The model assumes that a section in the beam has a trilinear moment—curvature relationship characterized by three particular points, initial cracking of concrete, yielding of non-prestressed steel, and crushing of concrete or rupturing of prestressing tendons. Predictions from the model were compared with the limited available test data, and a reasonable agreement was obtained. A detailed parametric study of the behavior of the prestressed concrete beams with hybrid FRP and stainless steel reinforcements was conducted. It can be concluded that the deformability of the beam can be enhanced by increasing the ultimate compressive strain of concrete, unbonded length of tendon, percentage of compressive reinforcement and partial prestress ratio, and decreasing the effective prestress in tendons, and increasing in ultimate compressive strain of concrete is the most efficient one. The deformability of the beam is almost directly proportional to the concrete ultimate strain provided the failure mode is concrete crushing, even though the concrete ultimate strain has less influence on the load-carrying capacity.

Flexural Response of Reinforced Concrete Beams Strengthened with End-Anchored Partially Bonded Carbon Fiber-Reinforced Polymer Strips

This paper presents the results of experimental and analytical studies carried out to investigate the flexural behavior of reinforced concrete beams strengthened with end-anchored partially bonded carbon fiber-reinforced polymer (CFRP) strips. A total of six beams, each 2400 mm long, 150 mm wide, and 250 mm deep with a tension steel reinforcement ratio of 1.18%, were tested. One beam was left unstrengthened as the control, another beam was strengthened with a fully bonded CFRP strip, and the remaining four beams were strengthened with partially bonded CFRP strips placed on the tension face of the beam and fixed at both ends using a mechanical anchor. The influence of varying the CFRP unbonded length (250 mm, 750 mm, 2×500 mm, and 1,250 mm) on the beam flexural response was studied. The experimental results revealed that end-anchored partially bonded CFRP strips significantly enhanced the ultimate capacity of the control beam and performed better than the fully bonded strip with no end-anchorage. This obse...

부분 비부착 NSM Hybrid FRP 보강근에 의한 철근콘크리트보의 연성보강

New strengthening method based on Near Surface Mounted technique (NSM) is suggested, which can overcome the brittle nature of failure inherent to those reinforced concrete beams strengthened with FRP composite materials. The suggested technique secures ductile failure of reinforced concrete beams by having the strengthening Hybrid FRP rebars unbonded in parts. Experiments were performed in order to compare structural behaviors of strengthened beams with and without unbending along the Hybrid FRP rebars. Test results showed that only those beams strengthened by partially unbonded NSM failed in ductile manner. Theoretical expressions were derived for the minimum unbonded length of Hybrid FRP rebars with which ultimate strength of the reinforced concrete beam with partially unbonded NSM could be reached. The suggested partially unbonded NSM technique is expected to significantly improve the structural behavior of the strengthened beam with FRP composite materials.