Ultraviolet Light-emitting Diodes Research Articles

Study of ultraviolet light emitting diodes with InGaN quantum dots and lattice matched superlattice electron blocking layers.

Ultraviolet light emitting diodes (UV-LEDs) face the challenges including insufficient hole injection and severe electron leakage. Quantum dots (QDs) have been proven to provide three-dimensionally localized states for carriers, thereby enhancing carrier confinement. Therefore, UV-LEDs employing InGaN QDs are designed and studied in this paper. The APSYs software is used to simulate UV-LEDs. Simulation results indicate that the QDs effectively improve the electron and hole concentration in the active region. However, UV-LEDs with QDs experience efficiency droop due to serious electron leakage. What's more, the lattice mismatch between last quantum barrier (LQB) and electron blocking layer (EBL) leads to the polarization field, which induces the downward band bending at the LQB/EBL interface and reduces effective barrier height of EBL for electrons. The AlInGaN/AlInGaN lattice matched superlattice (LMSL) EBL is designed to suppress electron leakage while mitigating lattice mismatch between LQB and EBL. The results indicate that the utilization of QDs and LMSL EBL contributes to increasing the electron and hole concentration in the active region, reducing electron leakage, enhancing radiative recombination rate, and reducing turn-on voltage. The efficiency droop caused by electron leakage is mitigated. When the injection current is 120 mA, the external quantum efficiency is increased to 9.3% and the output power is increased to 38.3 mW. This paper provides a valuable reference for addressing the challenges of insufficient hole injection and severe electron leakage.

Advancing sustainable seawater disinfection: Enhanced inactivation and mechanism of pulsed UV-LEDs irradiation on Tetraselmis sp.

Ultraviolet light-emitting diodes (UV-LEDs), as a novel ultraviolet light source with flexible pulse mode, has gained significant attention for applications in water disinfection and food sterilization. This study investigated the comparative inactivation efficiency of Tetraselmis sp. with continuous and pulsed UV-LEDs irradiation, exploring different wavelengths, duty rates and pulse frequencies. The results reveal a significant enhancement in inactivation efficiency (p < 0.05) under pulsed conditions even at the same UV dose, with inactivation efficiency increasing as duty rate or pulse frequency decreases. The optimal conditions for achieving peak inactivation efficacy are identified as a duty rate of 50% and a pulse frequency of 5 Hz. Within this parameter space, pulsed irradiation leads to a remarkable 1.7-fold increase in inactivation efficiency at UV265 nm and a 1.5-fold increase at UV285 nm compared to continuous irradiation, respectively. Additionally, the disruptive impacts on photosynthetic performance are more pronounced with pulsed irradiation, particularly at the 5 Hz pulse frequency. In shed of these findings, the application of pulsed UV-LEDs irradiation emerges as a promising alternative to the conventional continuous UV disinfection methods in the area of seawater disinfection, offering higher disinfection efficacy and energy consumption.

Phase composition and luminescent properties of cesium lead bromide perovskite nanopowders

Halide perovskite nanopowders were synthesized by ligand-assisted re-precipitation technique with different volume ratios of mixture solution to antisolvent (toluene). It was found that with an increase in the proportion of toluene, the phase formed as a result of recrystallization changes predominantly from Cs4PbBr6 to the CsPbBr3, while less stable CsPb2Br5 phase was also discovered. The change in the phase composition of powders obtained with different volume ratios of mixture solution to toluene is explained by the salting out effect of slightly soluble compounds. The phase composition had a correlation with the crystal size distribution, as well as with the photoluminescence quantum yield. Optical properties, including absorption spectra, photoluminescence excitation and luminescence spectra were investigated. Nanopowders obtained with a ratio of the mixture of solution to toluene of about 1:0.9 had the maximum quantum efficiency. The following was associated with the formation of low-dimensional CsPbBr3 “slabbed” crystals sticked on rhombohedral Cs4PbBr6 crystals. The composite film based on nanocrystals and thermoplastic polyurethane was made by hot pressing, the potential of its use as a phosphor coating for an ultraviolet LED was shown.

Non-destructive real-time analysis of plant metabolite accumulation in radish microgreens under different LED light recipes.

The future of human space missions relies on the ability to provide adequate food resources for astronauts and also to reduce stress due to the environment (microgravity and cosmic radiation). In this context, microgreens have been proposed for the astronaut diet because of their fast-growing time and their high levels of bioactive compounds and nutrients (vitamins, antioxidants, minerals, etc.), which are even higher than mature plants, and are usually consumed as ready-to-eat vegetables. Our study aimed to identify the best light recipe for the soilless cultivation of two cultivars of radish microgreens (Raphanus sativus, green daikon, and rioja improved) harvested eight days after sowing that could be used for space farming. The effects on plant metabolism of three different light emitting diodes (LED) light recipes (L1-20% red, 20% green, 60% blue; L2-40% red, 20% green, 40% blue; L3-60% red, 20% green, 20% blue) were tested on radish microgreens hydroponically grown. A fluorimetric-based technique was used for a real-time non-destructive screening to characterize plant methabolism. The adopted sensors allowed us to quantitatively estimate the fluorescence of flavonols, anthocyanins, and chlorophyll via specific indices verified by standardized spectrophotometric methods. To assess plant growth, morphometric parameters (fresh and dry weight, cotyledon area and weight, hypocotyl length) were analyzed. We observed a statistically significant positive effect on biomass accumulation and productivity for both cultivars grown under the same light recipe (40% blue, 20% green, 40% red). We further investigated how the addition of UV and/or far-red LED lights could have a positive effect on plant metabolite accumulation (anthocyanins and flavonols). These results can help design plant-based bioregenerative life-support systems for long-duration human space exploration, by integrating fluorescence-based non-destructive techniques to monitor the accumulation of metabolites with nutraceutical properties in soilless cultivated microgreens.

Multi-wavelength and broadband AlGaN-based LED for versatile and artificial UV light source

This study focuses on modeling and analyzing a multi-wavelength (MW) ultraviolet light-emitting diode (UV LED) equipped with grading transition layers, which holds potential as a versatile and artificial UV light source. Commencing with the exploration of simple dual and triple-wavelength UV LEDs, we delve into the device mechanism, including the role of the grading transition layer and the control of emission intensity ratios. The grading transition layer connects modules with different emission wavelengths, effectively enhancing hole injection by diminishing the effective hole barrier and providing three-dimensional hole gas (3DHG). Besides, the emission intensity ratio of different modules is modulated through electron overflow, which is finely and coarsely controlled respectively by altering the quantum well number and the Al composition of electron controlling layers (ECLs). Modulating the ECL composition and quantum well number has good unilaterality facilitated by using grading transition layers, promoting a lower overall design complexity. Band diagrams, current dynamics, and carrier concentration distribution are analyzed to uncover various device mechanisms. After investigating dual-wavelength and triple-wavelength LEDs, a broadband UV LED is designed and demonstrated through the numerical method. The LED incorporates five emission modules, and each module has a similar emission intensity, contributing to a near 100 nm width UV spectrum. We expect this work lays the foundation for MW and broadband UV LED designs, fostering advancements in the AlGaN-based UV LED community.

Inactivation effect and kinetic analysis of multi-band ultraviolet LED combined with Ag/N modified magnetic TiO2 on microorganisms in ballast water

The invasion of harmful aquatic organisms from ship ballast water is a serious threat to the marine ecosystem. However, the existing treatment technology has the defects of high energy consumption, secondary pollution and easy revival of organisms, etc. How to inactivate the microorganisms in ballast water efficiently is always a difficult challenge. In this study, the inactivation of Karenia mikimotoi and Escherichia coli under UVA/UVCLED photocatalytic system (UVA/UVCLED + Ag/N-Fe3O4-SiO2-TiO2) was investigated using Ag-modified and N-modified magnetic TiO2 nanomaterials. The results showed that the ability of 1.5 % Ag with 3 % N dual-modified TiO2 to enhance the system's biologically logarithmic inactivation rate was 4–5 times higher than that of conventional unmodified TiO2. The Ag/N-modified magnetic TiO2 had the best photocatalytic activity at a dosage of 500 mg/L. After 6 cycles of use, the inactivation efficiency in combination with UVA/UVCLED only decreased by 8.76 % compared with the initial use, and the recycling rate was still up to 95.75 %. Meanwhile, the scanning electron microscope showed that the photocatalyst itself only had some minor changes after 6 cycles, which confirmed the fact that the photocatalytic removal rate (higher than 91.24 %) could still be maintained at a high level. The UVA/UVCLED photocatalytic system significantly inhibited the scavenging ability of superoxide dismutase (SOD) on reactive oxygen species (ROS), enhanced the toxic effect of ROS on cells, and ultimately accelerated the process of apoptosis and inhibited biological resurrection. In addition, this study verified the inactivation kinetics of the target microorganisms using Chick-Watson, Hom and Biphasic models, and found that all individuals in the same population differed in their tolerance to UV radiation, and some of them absorbed more than a threshold dose of UV radiation before showing inactivation responses. The Biphasic model (R2: 0.99571–0.99926) can better simulate the nonlinear changes exhibited during the inactivation process and is more applicable to the actual disinfection situation of UVA/UVCLED photocatalytic systems. The UVA/UVCLED + Ag/N-Fe3O4-SiO2-TiO2 photocatalytic technology developed in this study, as a novel oxidation process, reduces energy consumption while effectively inhibiting the reanimation of organisms, and exhibits a strong potential for application in the fields of restoring the environment of water bodies and blocking the spread of pathogens.

Microplastics as potential barriers to ultraviolet light emitting diode inactivation of MS2 bacteriophage: Influence of water-quality parameters

Microplastics have emerged as a concerning contaminant in drinking water sources, potentially interacting with pathogenic microorganisms and affecting the disinfection processes. In this study, MS2 was selected as an alternative for the human enteric virus. The influence of microplastics polyvinylchloride (MPs-PVC) on ultraviolet light emitting diode (UV-LED) inactivation of MS2 was investigated under various water chemistry conditions, such as MPs-PVC concentration, pH, salinity, and humic acid concentration. The results revealed that higher concentrations of MPs-PVC led to the reduced inactivation of MS2 by decreased UV transmittance, hindering the disinfection process. Additionally, the inactivation efficiency of MS2 in the presence of MPs-PVC was influenced by pH, and acidic solution (pH at 4, 5, and 6) exhibited higher efficiency compared to alkaline solution (pH at 8 and 9) and neutral solution (pH at 7). The low Na+ concentrations (0–50 mM) had a noticeable effect on MS2 inaction efficiency in the presence of MPs-PVC, while the addition of Ca2+ posed an insignificant effect due to the preferential interaction with MPs-PVC. Furthermore, the inactivation rate of MS2 initially increased and then decreased with increasing the concentration of humic acid, which was significantly different without MPs-PVC. These findings shed light on the complex interactions between MPs-PVC and MS2 in the UV-LED disinfection process under various water-quality parameters, contributing to drinking water safety and treatment.

Electroluminescence efficiency and stability of near ultraviolet organic light-emitting diodes based on BCPO luminous materials

To date, in the traditional method of obtaining near-ultraviolet (NUV) light, mercury atoms, which can create a highly toxic heavy metal contaminant, have been used. Therefore, it is an important issue to obtain NUV light by using new environmentally friendly devices. In the last decade, the fabrication of near ultraviolet organic light-emitting diodes (NUV-OLEDs) has become a research hotspot in the field of organic electronics. However, when the electroluminescence wavelength is extended to shorter than 400 nm, higher requirements are put forward for the materials used for each functional layer in these devices. In this work, a wide bandgap small molecule material of BCPO is used as the luminescent layer. The electron-transporting and hole-transporting materials are determined based on the overlaps between absorption spectra of these materials and emission spectrum of BCPO. And NUV-OLEDs with electroluminescent peak wavelength at 384 nm are prepared. By using the optimal device structure, the maximum external quantum efficiency of the device reaches 2.98%, and the maximum radiance of the device reaches 38.2 mW/cm&lt;sup&gt;2&lt;/sup&gt;. In the electroluminescence spectrum, NUV light with wavelengths below 400 nm accounts for 57% of the light emission. In addition, the device demonstrates good stability when biased at two different constant voltage modes. The multiple key factors which affect the stability of the device are analyzed in detail. Firstly, it is found that the high glass transition temperature (&lt;i&gt;T&lt;/i&gt;&lt;sub&gt;g&lt;/sub&gt;) of hole-transporting material is very important for the long-time stability of this device. The poor device stability is closely related to the low &lt;i&gt;T&lt;/i&gt;&lt;sub&gt;g&lt;/sub&gt; temperature of hole-transporting material. Secondly, due to the widespread use of PEDOT:PSS as hole injection material in OLEDs, the electron leakage from the hole-transpor layer into the PEDOT:PSS layer may cause significant damage to the conducting polymer. When bombarded with low energy electrons, bond breakage occurs on the surface of PEDOT:PSS, followed by the release of oxygen and sulfur, resulting in changes in conductivity and oxidation reactions with molecules of hole transport material. Thirdly, the photoelectrical stability of organic molecules is the most fundamental reason that restricts the device lifetime. The aging process of material or device is directly relevant to the bond dissociation energy (BDE) of organic molecule. Generally, the BDE value of organic molecule is not high enough. As a result, molecules are prone to chemical bond breakage during electrochemical or photochemical aging. In summary, highly stable NUV-OLEDs should be fabricated by using hole-transporting materials with high &lt;i&gt;T&lt;/i&gt;&lt;sub&gt;g&lt;/sub&gt; temperature, sufficient electron-blocking capacity, and large BDE value.

Ion implantation induced nucleation and epitaxial growth of high-quality AlN

AlN materials have a wide range of applications in the fields of optoelectronic, power electronic, and radio frequency. However, the significant lattice mismatch and thermal mismatch between heteroepitaxial AlN and its substrate lead to a high threading dislocation (TD) density, thereby degrading the performance of device. In this work, we introduce a novel, cost-effective, and stable approach to epitaxially growing AlN. We inject different doses of nitrogen ions into nano patterned sapphire substrates, and then deposit the AlN layers by using metal-organic chemical vapor deposition. Ultraviolet light-emitting diode (UV-LED) with a luminescence wavelength of 395 nm is fabricated on it, and the optoelectronic properties are evaluated. Compared with the sample prepared by the traditional method, the sample injected with N ions at a dose of 1×10&lt;sup&gt;13&lt;/sup&gt; cm&lt;sup&gt;–2&lt;/sup&gt; exhibits an 82% reduction in screw TD density, the lowest surface roughness, and a 52% increase in photoluminescence intensity. It can be seen that appropriate dose of N ion implantation can promote the lateral growth and merging process in AlN heteroepitaxy. This is due to the fact that the process of implantation of N ions can suppress the tilt and twist of the nucleation islands, effectively reducing the density of TDs in AlN. Furthermore, in comparison with the controlled LED, the LED prepared on the high quality AlN template increases 63.8% and 61.7% in light output power and wall plug efficiency, respectively. The observed enhancement in device performance is attributed to the TD density of the epitaxial layer decreasing, which effectively reduces the nonradiative recombination centers. In summary, this study indicates that the ion implantation can significantly improve the quality of epitaxial AlN, thereby facilitating the development of high-performance AlN-based UV-LEDs.

A portable fluorescence detection device based on a smartphone employing carbon nanodots for Mn2+ sensing.

The measurement of fluorescence emission for quantitative analysis is typically based on a traditional spectrofluorometer, which limits an onsite detection approach. Thus, an alternative device should be developed for fulfilling this analysis outside of the laboratory. Therefore, a low-cost, portable, and low-energy consumption fluorescence reader-based smartphone device was developed. An ultraviolet light-emitting diodes (UV-LED) was used to construct the fluorescence device-based smartphone as a low-power excitation light source. The smartphone camera was used as a detector for detecting photons from the fluorescence emission process of the fluorescence probe and was connected to a digital image platform. Transparent acrylic with orange and yellow colors was employed as a filter for reducing the interference from light source intensity. The obtained digital image was converted to red, green and blue (RGB) intensity using a custom-designed smartphone application. N,S-doped carbon nanodots (N,S-CDs) were demonstrated to be a good fluorescence indicator for determining trace quantities of Mn2+ in cosmetics. The approach exhibited high selectivity and sensitivity, detecting and quantifying analytes at 1-5 μM concentrations. Furthermore, the method's detection limit of 0.5 μM reflects its capacity to detect trace amounts of a target analyte. Mn2+ in cosmetic products was successfully analyzed using this device with high accuracy comparable with the results from inductively coupled plasma-optical emission spectroscopy (ICP-OES).

Characterization of diesel spray with novel high-speed laser absorption scattering technique under diesel engine-like condition

In Diesel Engines, the injection process plays a decisive role in the combustion efficiency. Hence, the characterization of diesel sprays is very important. Several methods are developed, however, none of them records the temporal fuel distribution throughout the individual injection event and measures the liquid/vapor concentration of an evaporating diesel spray. In this work, two light sources i.e., an ultraviolet LED and a continuous wave laser, were used with two high-speed video cameras. A fuel mixture with the compositions of 97.5 % n-tridecane and 2.5 % of volume-based 1-methylnaphthalene was selected as the test fuel. The fuel was intermittently injected into an inert environment at 4.8 MPa and 800 K by applying a seven-hole injector with a hole diameter of 0.123 mm. The injection pressure was set at 100 MPa and the injection amounts were set as 2.5 and 5.0 mg/hole to observe the effect of the injected mass on the spray characteristics and mixture formation process. Calibration, based on the scattering by non-evaporating sprays and molar absorption coefficients for fully evaporated sprays, indicates a measurement error of 15 %. The findings of the experiments show that, under large injection mass conditions, the liquid phase equivalence ratio is quite low and close to zero just after the end of injection which points out that as the air-fuel mixing quality improves, the majority of the liquid fuel is rapidly converted to vapor. The air-fuel mixture is overall richer at large injected mass compared to the small mass condition. Furthermore, after the end of injection, the high fuel vapor concentration area near the nozzle soon mixes with ambient gas, decreasing the equivalence ratio to low levels, whereas a high-vapor-concentration region is still present at the spray head. This study provides a valuable insights into the behavior of the fuel spray, which could be used to improve the efficiency and performance of diesel engines.

Research Progress of AlGaN Ultraviolet Light-Emitting Diodes

The research progress of AlGaN ultraviolet light-emitting diodes (UV LEDs) is explored in this paper. Firstly, the significance and application areas of AlGaN UV LEDs are introduced, emphasizing their wide-ranging applications in fields such as disinfection, medical devices, and sensors. Subsequently, an overview of the material science and manufacturing processes used in the production of AlGaN UV LEDs is provided, including crystal growth techniques and fabrication processes. Next, the design, structure, and operating principles of different types of AlGaN UV LEDs are described, with a focus on the devices optical performance, electrical characteristics, and thermal management effects. Finally, the latest research findings are summarized, and the challenges and future development directions facing current technology are discussed. This paper aims to provide readers with a comprehensive understanding of the research field of AlGaN UV LEDs and serve as a reference for future research and applications.

Research Progress of the Application of UV Light-Emitting Diodes for Water Disinfection

With the increasing global demand for safe drinking water, the search for effective and economical water treatment technologies has become an urgent need. Ultraviolet (UV) light sterilization is a proven method for eliminating bacteria in water, but traditional UV systems often rely on mercury lamps, which pose potential environmental and health risks. In recent years, the development of UV-LED technology has offered a new solution for water treatment. This article provides a detailed explanation of the working principles, technological advantages, and applications of UV-LEDs in water treatment. By comparing them with traditional UV systems, UV-LEDs not only demonstrate lower energy consumption and longer lifespan, but also avoid the use of toxic mercury. Despite current challenges in cost and technological maturity, the environmental friendliness and efficiency potential of UV-LED technology indicate a promising market outlook. This article aims to provide a comprehensive review of UV-LED technology for practitioners and researchers in the water treatment industry, and to explore its future development directions.

Reticular synthesis of 8-connected carboxyl hydrogen-bonded organic frameworks for white-light-emission.

The rational design and construction of hydrogen-bonded organic frameworks (HOFs) are crucial for enabling their practical applications, but controlling their structure and preparation as intended remains challenging. Inspired by reticular chemistry, two novel blue-emitting NKM-HOF-1 and NKM-HOF-2 were successfully constructed based on two judiciously designed peripherally extended pentiptycene carboxylic acids, namely H8PEP-OBu and H8PEP-OMe, respectively. The large pores within these two HOFs can adsorb fluorescent molecules such as diketopyrrolopyrrole (DPP) and 9-anthraldehyde (AnC) to form HOFs ⊃ DPP/AnC composites, subsequently used in the fabrication of white-light-emitting devices (WLEDs). Specifically, two WLEDs were assembled by coating NKM-HOF-1 ⊃ DPP-0.13/AnC-3.5 and NKM-HOF-2 ⊃ DPP-0.12/AnC-3 on a 330 nm ultraviolet LED bulb, respectively. The corresponding CIE coordinates were (0.29, 0.33) and (0.32, 0.34), along with corresponding color temperatures of 7815 K and 6073 K. This work effectively demonstrates the feasibility of employing reticular chemistry strategies to predict and design HOFs with specific topologies for targeted applications.

A novel blue emitting phosphor Ca1-ySryScBO4:Bi3+ with zero-thermal quenching for multi-scenario application.

In recent years, Bi3+ activated phosphors have received a lot of attention from researchers; however, the performance and application areas of phosphors are yet to be developed. In this work, a series of CaScBO4(CSBO):xBi3+ phosphors were successfully prepared using a high-temperature solid-state method. Under UV excitation, blue light emission was achieved at 430 nm with a quantum yield of 91%, and at 423 K, the emission intensity retained 82.8% of the original intensity at 298 K. By crystal field engineering, the substitution of Sr2+ at the Ca2+ site enhances the temperature stability of the material, and at 423 K, 473 K and 573 K, the samples maintain 104%, 103% and 85% of the emission intensity at room temperature, respectively. It indicates that the cation substitution causes the increase in the oxygen vacancy concentration, and the oxygen vacancy defect compensates the energy lost in electrons at high temperature, producing resistance to anti-TQ performance. Finally, a blue-violet LED was fabricated by using the phosphor and an ultraviolet LED chip, and white LEDs (CCT = 4683 K, Ra = 89.7) were obtained by co-packaging this phosphor with commercial phosphors and a UV chip. Importantly, the great potential of this phosphor in the field of plant lighting and biocontrol can be demonstrated.

Carrier transport barrier in AlGaN-based deep ultraviolet LEDs on offcut sapphire substrates

Carrier transport barrier in AlGaN-based deep ultraviolet LEDs on offcut sapphire substrates

Influence of period number of superlattice electron barrier layer on the performance of AlGaN-based deep ultraviolet LED

The development of AlGaN-based deep ultraviolet light emitting diodes (DUV-LEDs) is currently limited by poor external quantum efficiency (EQE) and wall-plug efficiency (WPE). Internal quantum efficiency (IQE), as an important component of EQE, plays a crucial role in improving the performance of DUV-LEDs. The IQE is related to the carrier injection efficiency and the radiation recombination rate in the active region. In order to improve the IQE of AlGaN-based DUV-LEDs, this work proposes a scheme to optimize the period number of superlattice electron barrier layer (SL-EBL) to achieve better carrier injection efficiency and confinement capability. The effect of the period number of SL-EBL on the luminous efficiency, reliability and carrier recombination mechanism of AlGaN-based DUV-LEDs with an emission wavelength of 273 nm are investigated. The experimental results show that the light output power (LOP), external quantum efficiency (EQE) and wall-plug efficiency (WPE) of the DUV-LEDs tend to first increase and then decrease with the period number of SL-EBL increasing, while the leakage current decreases and the reliability is enhanced. The maximum EQE and WPE of the DUV-LED are 3.5% and 3.2%, respectively, at an injection current of 7.5 mA when the period number of SL-EBL is fixed at 7 (the thickness is 28 nm). Meanwhile, the numerical simulation results show that the electron potential barrier height is enhanced with the period number of SL-EBL increasing, and the variation of the hole potential barrier height is negligible. Therefore, increasing the period number of SL-EBL is beneficial to shielding the dislocations and suppressing the leakage of electrons into the p-type layer, which improves the luminous efficiency and reliability of DUV-LEDs. However, when the period number of SL-EBL exceeds 7, the excessively thick hole potential barrier prevents the holes from entering into the activation region and reduces the radiative recombination efficiency. Therefore, EQE and WPE will show an inflection point with the variation of the period number of SL-EBL. In addition, to investigate the carrier recombination mechanism of the active region, the experimental EQE curves are fitted by the ABC model as well as the different slopes in logarithmic light output power-current (&lt;i&gt;L-I&lt;/i&gt; ) curves are calculated after aging. It can be found that increasing the period number of SL-EBL can effectively suppress the non-radiative combination of carriers in the active region. This investigation can provide an alternative way to enhance the photoelectric performance of DUV-LEDs.

Improvement of Heat Dissipation Performance of Deep Ultraviolet LED

Improvement of Heat Dissipation Performance of Deep Ultraviolet LED

Developing Sterilization and Lighting Systems for Sprouting Rooms Using Ozone and Optical Fibers

The increasing population has led to the widespread adoption of hydroponics. Hydroponic production of fresh green forage requires minimal space, does not use soil, and allows for rapid harvesting. A fully controlled sprouting room can yield a substantial amount of green fodder from a small area with less water consumption. This study aims to investigate the effectiveness of ozone on seed germination, seedling growth, and microbial sterilization during germinated barley processing. Additionally, the sterilization of the barley sprouting room was conducted using ultraviolet and infrared light, which provides optimal sprouting conditions.The study comprises three experimental variables: three levels of ozonized water (13, 26, and 39 mg L-1) combined with three light sources (fluorescent, infrared, and ultraviolet) and three light duration times (8, 16, and 24 h). The measurements include shoot length, fresh yield weight, dry yield weight, conversion factor, chlorophyll content, N, P, K, crude protein, ash, and log reduction.The results indicated that the maximum values were observed when using ozonized water at 39 mg L-1, Ultraviolet LED as a light source, and a sterilizing medium with a light duration time of 24 h. Conversely, the minimum values were observed when using ozonized water at 13 mg L-1, fluorescent LEDs as a light source, and a light duration time of 8 h. Based on the findings, it is highly recommended to utilize the developed sprouting room throughout the year for the production of fresh forage.

Structural, optical and photoluminescence properties of BaLa2ZnO5: Eu3+ phosphor: A prospective red-emitting phosphor for LED applications

Herein, we report the synthesis of red-emitting Eu3+-activated BaLa2ZnO5 phosphors using a high-temperature solid-state reaction technique. The phase confirmation and crystal structure were established through X-ray powder diffraction patterns. Density-functional theory calculations revealed an indirect bandgap in the material. The bandgaps of both undoped and doped BaLa2ZnO5 phosphors were analyzed using diffuse reflectance spectra. The influence of Eu3+ doping on the bandgap was confirmed by applying the Kubelka-Munk function to the diffuse reflectance spectra. The effects of doping on the surface morphology and elemental composition were investigated through field emission scanning electron microscopy and energy-dispersive spectroscopy, respectively. Additionally, X-ray photoelectron spectroscopic studies were conducted to analyze the electronic structure, chemical states and impact of doping on the crystal structure. Using near ultraviolet excitation at 329 nm, the synthesized phosphor exhibited strong red emission attributed to various 5D0 → 7FJ transitions. Concentration quenching phenomena were observed due to dipole-dipole interactions. Judd-Ofelt analysis was performed to elucidate the coordination nature of the doping element in the host lattice. Excellent thermal stability was observed with an activation energy of 0.64 eV for discharging via lattice vibrations. The better color purity (98–99.3 %) and stable Commission Internationale de l’Elcairage coordinates in the red region of the gamut suggest that the prepared phosphor material holds potential as an efficient candidate for ultra violet and blue light-emitting diode chips, as well as an efficient component in the fabrication of white light-emitting diodes.