Ultra-high Molecular Weight Polyethylene Tape Research Articles

Biomechanical Comparison of Tape Versus Suture in Simulated Achilles Tendon Midsubstance Rupture

As sutures have progressed in strength, increasing evidence supports the suture tendon interface as the site where most tendon repairs fail. We hypothesized that suture tape would have a higher load to failure versus polyblend suture due to its larger surface area. Eleven matched pairs of cadaveric Achilles tendons were sutured with 2 mm wide braided ultrahigh molecular weight polyethylene tape (Tape) or 2 mm wide braided ultrahigh molecular weight polyethylene suture (Suture) using a Krackow repair method. All Achilles repair constructs were cyclically loaded, after which they were loaded to failure. Change in suture footprint height, clinical and ultimate load to failure, and location of failure was recorded. Clinical loads to failure for Tape and Suture were 290.4 ± 74.8 and 231.7 ± 70.4 Newtons, respectively (p= .01). Ultimate loads to failure for Tape and Suture were 352.9 ± 108.1 and 289.8 ± 53.7 Newtons, respectively (p = .11). Cyclic testing resulted in significant changes in footprint height for both Tape and Suture, but the 2 sutures did not differ in terms of the magnitude of change in footprint height (p = .52). The suture tendon interface was the most common site of failure for both Tape and Suture. Our results suggest that Tape may provide added repair strength in vivo for Achilles midsubstance rupture.

Ultra-high-molecular-weight polyethylene sublaminar tape as semirigid fixation or pedicle screw augmentation to prevent failure in long-segment spine surgery: an ex vivo biomechanical study.

Complications after adult spinal deformity surgery are common, with implant-related complications occurring in up to 27.8% of cases. Sublaminar wire fixation strength is less affected by decreasing trabecular bone density in comparison to pedicle screw (PS) fixation due to the predominant cortical bone composition of the lamina. Sublaminar fixation may thus aid in decreasing implant-related complications. The goal of this study was to compare fixation characteristics of titanium sublaminar cables (SCs), ultra-high-molecular-weight polyethylene (UHMWPE) tape, PSs, and PSs augmented with UHMWPE tape in an ex vivo flexion-bending setup. Thirty-six human cadaver vertebrae were stratified into 4 different fixation groups: UHMWPE sublaminar tape (ST), PS, metal SC, and PS augmented with ST (PS + ST). Individual vertebrae were embedded in resin, and a flexion-bending moment was applied that closely resembles the in vivo loading pattern at transitional levels of spinal instrumentation. The failure strength of PS + ST (4522 ± 2314 N) was significantly higher compared to the SC (2931 ± 751 N) and PS (2678 ± 827 N) groups, which had p values of 0.028 and 0.015, respectively (all values expressed as the mean ± SD). Construct stiffness was significantly higher for the PS groups compared to the stand-alone sublaminar wiring groups (p = 0.020). In contrast to SC, ST did not show any case of cortical breach. The higher failure strength of PS + ST compared to PS indicates that PS augmentation with ST may be an effective measure to reduce the incidence of screw pullout, even in osteoporotic vertebrae. Moreover, the lower stiffness of sublaminar fixation techniques and the absence of damage to the cortices in the ST group suggest that ST as a stand-alone fixation technique in adult spinal deformity surgery may also be clinically feasible and offer clinical benefits.

Knotless Anchor Fixation for Transosseous Meniscal Root Repair Using Suture Tape Is Inferior Compared With Button or Screw Fixation: A Biomechanical Study.

Background:A 2 mm–wide ultrahigh-molecular-weight polyethylene (UHMWPE) tape improves the contact pressure at root repair sites compared with high-strength suture and provides a stronger repair construct. UHMWPE tape is commonly used in rotator cuff repair, and fixation is often achieved with knotless suture anchors. The optimal method for tape fixation for meniscal root repair has not been established.Hypothesis:The use of suture anchors for the tibial fixation of 2-mm UHMWPE tape transosseous root repairs will lead to better biomechanical performance compared with other fixation methods.Methods:The medial meniscal posterior root attachment in 25 porcine knees was divided, and a standardized transtibial root repair was performed using 2-mm UHMWPE tape. The testing was performed by cyclic loading followed by load to failure. Tibial fixation was randomized to 5 tibial fixation types: (1) cortical fixation button, (2) pound-in suture anchor with screw-down interference suture locking, (3) tap-in suture anchor with inner locking plug, (4) postscrew, and (5) postscrew and washer.Results:There was no difference in displacement during cyclic loading between tibial fixation groups except for a highly significant difference in the maximum load at failure. Repairs in both suture anchor fixation groups all failed by tape slippage at relatively low loads (median, 145 and 116 N, respectively). Repairs tied over a cortical button, postscrew, or screw and washer failed by tape breakage at loads of 431, 405, and 528 N.Conclusion:For meniscal root repairs with 2-mm UHMWPE tape, use of suture anchors offers weaker fixation compared with tying over a button or postscrew/washer. While suture anchor fixation may be adequate for nonweightbearing postoperative protocols, it may not allow for more accelerated weightbearing.

Minimum 5-year Follow-up Results for Occipitocervical Fusion Using the Screw-Rod System in Craniocervical Instability.

Retrospective clinical study. To evaluate the clinical outcome of patients who had undergone occipitocervical (OC) fusion using pedicle screws and rods over a minimum 5-year follow-up. Few studies have evaluated occipitocervical (OC) fusion using pedicle screws and rods for long-term follow-up. Twenty-seven consecutive patients treated underwent posterior OC fusion using pedicle screws and rods over a minimum 5-year follow-up. The Modified McCormick scale to grade a patient's functional status and the Japanese Orthopaedic Association (JOA) scoring system were used to evaluate preoperative and postoperative neurological function. We assessed fusion by both direct and indirect evidence; bony trabeculae at the graft-recipient interface on lateral cervical radiographs and sagittal computed tomography reconstruction was considered direct evidence of union. The mean follow-up period was 7.2 years (5-14 y). JOA scores were 8.1±3.8 before surgery and 11.7±3.7 at the final follow-up. The recovery rate calculated from the JOA scores was 42.0±30.0%. Functional status did improve at least 1 grade according to the modified McCormick scale in 18 patients (66.7%). There was no deterioration at the final follow-up.There were postoperative implant-related complications in 8 patients (29.6%): loosening of pedicle screws in 2, rod breakage in 2, plate breakage in 1, screw breakage in 1, pullout of pedicle screws in 1, and wiring induced myelopathy in 1 patient. The average duration between surgery and implant failure was 31.2 months (12-60 mo) except for 2. Sufficient bone grafting, proper decortication of the bone bed, using thicker and high stiffness rods, and ultra-high molecular weight polyethylene tape as a fixation or reinforcement of implant may help prevent implant failure.

Posterior Surgery for Adolescent Idiopathic Scoliosis With Pedicle Screws and Ultrahigh–Molecular Weight Polyethylene Tape

Study Design: Prospective clinical case series. Objectives: To describe our surgical procedure and results for posterior correction and fusion with a hybrid approach using pedicle screws, hooks, and ultrahigh–molecular weight polyethylene tape with direct vertebral rotation (DVR) (the PSTH-DVR procedure) for treatment of adolescent idiopathic scoliosis (AIS) with satisfactory correction in the coronal and sagittal planes. Summary of Background Data: Introduction of segmental pedicle screws in posterior surgery for AIS has facilitated good correction and fusion. However, procedures using only pedicle screws have risks during screw insertion, higher costs, and decreased postoperative thoracic kyphosis. We have obtained good outcomes compared with segmental pedicle screw fixation in surgery for AIS using a relatively simple operative procedure (PSTH-DVR) that uses fewer pedicle screws. Methods: The subjects were 30 consecutive patients with AIS who underwent the PSTH-DVR procedure and were followed for a minimum of 2 years. Preoperative flexibility, preoperative and postoperative Cobb angles, correction rates, loss of correction, thoracic kyphotic angles (T5–T12), coronal balance, sagittal balance, and shoulder balance were measured on plain radiographs. Rib hump, operation time, estimated blood loss, spinal cord monitoring findings, complications, and scoliosis research society (SRS)-22 scores were also examined. Results: The mean preoperative curve of 58.0 degrees (range, 40–96 degrees) was corrected to a mean of 9.9 degrees postoperatively, and the correction rate was 83.6%. Fusion was obtained in all patients without loss of correction. In 10 cases with preoperative kyphosis angles (T5–T12) <10 degrees, the preoperative mean of 5.8 degrees improved to 20.2 degrees at the final follow-up. Rib hump and coronal, sagittal and shoulder balances were also improved, and good SRS-22 scores were achieved at final follow-up. Conclusions: The correction of deformity with PSTH-DVR is equivalent to that of all-pedicle screw constructs. The procedure gives favorable correction, is advantageous for kyphosis compared with segmental screw fixation, and uses the minimum number of pedicle screws. Therefore, the PSTH-DVR procedure may be useful for treatment of idiopathic scoliosis.

Ultra-High Molecular Weight Polyethylene Tape Applied for Distal Humeral Condyle Fracture around Total Elbow Arthroplasty in Patients with Rheumatoid Arthritis: Report of Two Cases

Managing fractures of distal humerus in patients with rheumatoid arthritis (RA) is technically challenging. Total elbow arthroplasty (TEA) is one of the treatment options for these fractures. While elbow motion is largely regained by TEA, comminuted condyle fragments are often ignored. Although numerous approaches for repair of condylar fragments around TEA are described, any universal fixation strategy for these fractures has not been established. This report describes, for the first time, application of an ultra-high molecular weight polyethylene (UHMWPE) tape for the treatment of distal humerus fracture in 2 patients with rheumatic elbow arthropathy. The post-operative clinical courses were good. Radiographs showed bony union of the condylar fragments without loosening in two cases. Because of its flat configuration, softness, and flexibility, UHMWPE tape is a promising material for stabilizing fracture of the distal humerus associated with TEA.

Modified Mostardi approach with ultra-high-molecular-weight polyethylene tape for total hip arthroplasty provides a good rate of union of osteotomized fragments

BackgroundA lateral approach is common in total hip arthroplasty because of the good exposure it provides and its low complication rates. However, a drawback of the procedure is that the abductor mechanism is damaged when the tendinous insertion of the abductor muscle is split. Here, we describe a wafer technique using ultra-high-molecular-weight polyethylene tape for promising reattachment of the abductor mechanism. MethodsWe retrospectively evaluated 120 consecutive primary total hip arthroplasties performed using a modified Mostardi approach, which involved reattaching the trochanter using either a braided polyester suture (polyester suture group, n=60) or ultra-high-molecular-weight polyethylene tape (UHMWPE tape group, n=60). The osteotomized fragment was reattached by inducing bone-to-bone contact using 3-mm-wide tapes that were precisely tied with a double-loop sliding knot in conjunction with a cable gun tensioner. The abductor strength and radiographic union rate were postoperatively assessed at 4 weeks and 6 months, respectively. ResultsA statistically significant lower incidence of nonunion and cutout was observed in the UHMWPE group (0 and 5.0 %, respectively) compared to the polyester suture group (8.3 and 15 %, respectively). No differences in abductor strength either preoperatively or at 4 weeks postoperatively were observed between the groups. In radiographically healed patients, abductor strength at 4 weeks post-surgery exceeded preoperative strength. The recovery rate of hip abductor strength was 109.9±34.3 % in union patients and 92.9±23.3 % in nonunion patients, which was statistically significant. The mean Japanese Orthopedic Association hip scores improved from 48.6 to 86.8 in union patients and from 50.3 to 85.9 in nonunion patients at 1 year postoperatively; however, this difference was not significant. ConclusionsThe modified Mostardi approach using ultra-high molecular weight polyethylene tape can promote successful union of the osteotomized fragment.

Comparison of Novel Ultra-high Molecular Weight Polyethylene Tape Versus Conventional Metal Wire for Sublaminar Segmental Fixation in the Treatment of Adolescent Idiopathic Scoliosis

Retrospective study. To compare the surgical outcomes of posterior translational correction and fusion using hybrid instrumentation systems with either sublaminar Nesplon tape or sublaminar metal wire to treat adolescent idiopathic scoliosis (AIS). Nesplon tape, which consists of a thread of ultra-high molecular weight polyethylene fibers, has advantages over metal wire: (1) its soft and flexible properties avoid neural damage and (2) its flat configuration avoids focal distribution of the stresses to lamina; however, the efficacy of Nesplon tape in the correction of spinal deformity is as yet, still unclear. Thirty AIS patients at a single institution underwent posterior correction and fusion using hybrid instrumentation containing hook, pedicle screw, and either sublaminar polyethylene taping (15) or sublaminar metal wiring (15). Patients were evaluated preoperatively, immediately after surgery, and at a 2-year follow-up according to the radiographic changes in curve correction, operating time, intraoperative blood loss, complications, and the Scoliosis Research Society patient questionnaire (SRS-24) score. The average correction rate was 63.0% in the Nesplon tape group and 59.9% in the metal wire group immediately after surgery (P = 0.62). Fusion was obtained in all the patients without significant correction loss in both groups. There was no significant difference in operative time, intraoperative blood loss, and postoperative SRS-24 scores between the 2 groups. Complications were superficial skin infection in a single patient in the Nesplon tape group, and transient sensory disturbance in 1 patient and temporal superior mesenteric artery syndrome in another patient in the metal wire group. The efficacy of Nesplon tape in correction of deformity is equivalent to that of metal wire, and fusion was completed without significant correction loss. The soft and flexible properties and flat configuration of Nesplon tape make this a safe application for the treatment of AIS with bone fragility or with the fusion areas containing the spinal cord.

A Biomechanical Study of 3 Different Types of Sublaminar Wire Used for Constructs in the Thoracic Spine

A biomechanical study was carried out on 3 different types of sublaminar wire used in constructs to secure the thoracic spine: stainless steel monofilament wire (steel wire), titanium cable (cable), and ultra-high molecular weight polyethylene tape (tape). Two experiments were carried out. Experiment 1: Thirty-one fresh human thoracic vertebrae classified as osteoporotic (bone mineral density of <0.8 g/cm2) were used. The steel wire, cable, or tape was placed sublaminarly and a tensile force was applied until the steel wire, cable, or tape cut 5 mm through the lamina, and the force at this point was noted. Experiment 2: Seven fresh human thoracic spines (T7-T10) were biomechanically tested as follows: axial compression (250 N), flexion (7.5 Nm), extension (7.5 Nm), left lateral bending (7.5 Nm), right lateral bending (7.5 Nm), left axial torsion (10 Nm), and right axial torsion (10 Nm). This sequence was applied to the intact spine. The spine was then de-stabilized and then restabilized using one or other of the 3 different types of sublaminar wires. The biomechanical testing was then repeated on the restabilized spine and stiffness curves were generated. In the laminar cut-through test, the cut-through force for tape was higher than that for either steel wire or cable. In the biomechanical stiffness testing, there was no significant difference between the 3 different sublaminar wiring constructs in any of the loading modes tested. The results of both experiments suggest that tape is as good, if not better, than steel wire or cable as a sublaminar wiring construct material.

Clinical Study of a Modified Brooks Technique for Atlanto-axial Subluxation Using Polyethylene Tape

Forty-four patients, 15 males and 29 females (3-71 years old; mean age, 52.9), were treated for the control of cervical instability with a modified Brooks operation using Tekmilon tape (an ultrahigh molecular weight polyethylene tape) instead of metal wires. Forty of the patients had rheumatoid arthritis (RA) with atlanto-axial subluxation (AAS), three patients had os odontoideum, and one patient had a cervical spine injury. The mean follow-up period was 8 years and 4 months. These patients were divided into three groups: 30 years or less, 31 to 60 years, and over 60 years. Atlanto-dental interval (ADI), inclination angle of atlanto-axial vertebrae (A-A angle), and bone fusion were examined on plain radiographs. The proportion of patients with reduced neck pain (Ranawat's grade 0 or grade 1) increased from 42.5% to 97.9% at the time of postoperative evaluation. Surgical complications, such as dural tear, lamina fracture, and spinal cord injury did not occur in any cases. Thirty-nine patients (88.6%) achieved bone union. ADI in the maximum flexed position improved from 10.3 to 2.5 mm. There was no statistical difference between ADI in males and females. ADI did not change in any age group both before and after surgery. A-A angle also improved from 9.4 to 24.4 degrees. The polyethylene tapes, used for internal fixation, caused no neurologic complications during sublaminar wiring and produced no MR artifacts. This modified Brooks technique using Tekmilon tape was proved to be a simple and safe treatment of AAS.