Types Of Phase Change Materials Research Articles

Structure Design and Heat Transfer Performance Analysis of a Novel Composite Phase Change Active Cooling Channel Wall for Hypersonic Aircraft.

Efficient and stable heat dissipation structure is crucial for improving the convective heat transfer performance of thermal protection systems (TPSs) for hypersonic aircraft. However, the heat dissipation wall of the current TPS is limited by a single material and structure, inefficiently dissipating the large amount of accumulated heat generated during the high-speed maneuvering flight of hypersonic aircraft. Here, a convection cooling channel structure of TPS is proposed, which is an innovative multi-level structure inspired by the natural honeycomb. An active cooling channel (PCM-HC) is designed by using a variable-density topology optimization method and filled with phase change material (PCM). Numerical simulations are used to investigate the thermal performance of the PCM-HC wall, focusing on the influence of PCM properties, structural geometric parameters, and PCM types on heat transfer characteristics. The results demonstrate that the honeycomb-like convection cooling channel wall, combined with PCM latent heat of phase change, exhibits superior heat dissipation capability. With a heat flux input of 50 kW/m2, the maximum temperature on the inner wall of PCM-HC is reduced by 12 K to 20 K. Different PCMs have opposing effects on heat transfer performance due to their distinct thermophysical properties. This work can provide a theoretical basis for the design of high-efficiency cooling channel, improving the heat dissipation performance in the TPS of hypersonic aircraft.

Efficiency enhancement in direct thermal energy storage systems using dual phase change materials and nanoparticle additives

The study aims to enhance the reliability of direct thermal energy storage (TES) using phase change materials (PCMs) and nanoparticles, ensuring sustained heat supply even during periods of low or intermittent solar radiation. The study specifically investigates a TES system comprising a double-cylindrical shell container with two distinct PCM types: petroleum jelly or petrolatum with 1 % Al2O3 nanoparticles by volume in the outer shell and wax in the inner shell. Additionally, a redesigned heat exchanger is employed to improve heating efficiency. The study examines two configurations: an open system and a closed system with a storage water tank. The deliberate strategy of augmenting PCM volume is aimed at enhancing heat transfer during both the charging and discharging phases. The performance of closed and open system configurations is compared, with a focus on highlighting the temperature profiles during the charging and discharging processes. The incorporation of 1 % Al2O3 nanoparticles in the PCMs led to a significant enhancement in efficiency, with the two-phase materials case achieving the highest efficiency of 73 %. Furthermore, the utilization of nanoparticles resulted in an improvement in efficiency of approximately 5 %. These findings demonstrate the potential of using dual PCM layers with NPs additives in direct TES systems.

Design optimization of the cooling systems with PCM-to-air heat exchanger for the energy saving of the residential buildings

Driven by a rapid surge in cooling demand in buildings, the energy consumption dedicated to cooling has experienced remarkable growth. To address this challenge, the adoption of latent heat thermal energy storage utilizing phase change materials (PCM) has gained significant momentum in recent years. This paper presents the design and evaluation of an integrated latent heat thermal energy storage (ILHTES) system tailored for residential buildings. This system integrates a PCM-to-air heat exchanger (PAHX) with an air conditioning unit. Modelica language is utilized to develop a numerical model for the ILHTES system. The heat transfer model of the PAHX is developed and validated using existing literature data. To simulate the dynamic behavior and energy consumption of the residential building, the open-source library AixLib is adopted. The developed ILHTES system model is used for the optimization of key design variables, including the PCM slab thickness and air flow rate, based on the results of long-term simulations covering the entire cooling season. Evaluation of the energy saving potential of the optimized ILHTES systems is carried out in comparison to conventional air conditioning systems, considering various climatic conditions in five European cities. The results highlight the profound impact of PCM types on the Energy Saving Ratio (ESR) throughout the entire cooling season. Among the four commercially available PCMs examined—RT27, RT25, RT20, and RT18—RT25 consistently outperforms the others. Across all five cities investigated, using RT25 leads to a minimum ESR of 16% in Catania and a maximum ESR of 44.7% in Stockholm for the entire cooling season.

Physical and Mechanical Properties of Fiberboard Made of MDF Residues and Phase Change Materials

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs (liquid and microencapsulated), two PCM ratios (2% and 6%), and two types of adhesives (urea-formaldehyde and phenol-formaldehyde) were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties—modulus of elasticity (MOE) and modulus of rupture (MOR)—were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with an MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with an MOE value of 2072.4 MPa and an MOR value of 16.4 MPa, when microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study developed fiberboards with adequate physical and mechanical properties and capable of storing thermal energy.

Performance comparison of a fixed-bed solar grain dryer with and without latent heat storage

Latent heat storage has gained attention as an energy storage method for solar drying due to its high storage density. However, its overall impact in drying performance has not been sufficiently investigated. This study presents detailed, validated mathematical models necessary for the transient simulation of a solar dryer with latent heat storage with the aim of assessing the effect that such storage has on the deep bed drying of wheat. Computer simulations were run with weather data from Germany. A fixed bed dryer with a capacity of one ton was assumed and the size of the solar air heater and latent heat storage unit was varied, as well as the type of phase change material. In drying wheat without storage from 22% to 13% w.b. (0.28 to 0.15 kg kg−1 d.b.), increasing solar collecting area from 6 to 15 m2 reduced drying time by around 50% but resulted in excessive temperatures. At equal collecting area, the use of latent heat storage changed drying time by −5% to +13.9% depending on component sizes, but the drying air temperature was limited effectively if solar collection and storage units are properly sized in relation to each other. Failure to do so can result in higher drying temperatures than recommended or bring little additional benefit. Moisture uniformity at the end of drying was slightly improved by up to 10% in the presence of the storage unit due to a reduction in the average drying temperature. The presented models and corresponding simulation programs are a useful tool to size the components of a solar dryer with and without latent heat storage.

مراجعة على التقييم الاقتصادي لدمج المواد المغلفة متغيرة الطور في أغلفة المباني

The worldwide energy crisis has made energy-saving a topic of concern in almost every country. Previous research has explored the use of thermal energy storage materials (TES), such as phase change materials (PCMs), as an effective energy-saving technique. Among various immersion techniques, macro-encapsulation has proven to be efficient, safe, and convenient. However, choosing the right PCM system can be complicated due to the variety of available PCM types, encapsulation materials, and encapsulation shapes. Moreover, while macro-encapsulated PCM systems are efficient, their feasibility depends on several factors, including energy prices, economic situation, and climatic conditions. Therefore, this research aims to provide a comprehensive overview to help create a deeper understanding of the design and application of macro-encapsulated PCM systems. It explains the different types of PCM, encapsulation materials, and encapsulation shapes, guiding the selection for the most appropriate system regarding the surrounding environment. Additionally, it aims to present a guideline for conducting feasibility studies on energy-saving systems such as PCM. A total of 80 research papers covering the intersection between the thermal performance of PCM and the economic assessment have been categorized, studied, and analyzed in order to identify the most accurate method of assessing the system’s feasibility. By providing a base knowledge regarding the various types of each element of the system and the factors that govern the selection of each, this research will help engineers appropriately design the system. In addition, providing a detailed guideline to the assessment of the system shall aid the decision makers in determining the system’s feasibility which encourages its application. Finally, the research investigates and addresses the key issues for future studies.

Composite phase change materials with room-temperature-flexibility

Phase change materials (PCMs) have attracted considerable attention for effectively addressing the problem of thermal energy supply–demand mismatch. However, the practical application of PCMs is still hindered by inherent challenges such as crystalline rigidity, leakage susceptibility, and poor thermal conductivity. In this research, on the basic of thermal control provided by phase change storage and the elastic behavior supported by thermoplastic polyester elastomer at room temperature, we fabricated a new type of composite PCM (CPCM) that exhibits flexibility even at room temperature. This CPCM demonstrates good shape and thermal stability. Furthermore, the carbon nanotubes-COOH modified with lauric acid (LA) can be uniformly dispersed within the CPCM matrix, thereby enhancing the thermal conductivity of the CPCM. Additionally, the composite material exhibits a promising thermal management performance for high-temperature lithium-ion (Li-ion) batteries. These findings open up new possibilities for the development of room- temperature flexible CPCMs.

Energy assessment of a sliding window integrated with PV cell and multiple PCMs

Windows often serve as a thermal weak point between a room's interior and the outside world. As such, we are exploring a new design for a sliding window that integrates both multiple phase change materials (PCMs) and photovoltaic (PV) cells. During the day, the PV cells produce electricity, which can be used in the building during the night. The sliding mechanism introduces several innovative features: use the PV-PCM glass unit (as the external sliding layer) or a standard glass unit (the internal sliding component). The PV-PCM window also can be used as a sliding light shutter or curtain. The PV cell in the proposed design is operated in the closed and open case due to the sliding design. We compared the thermal performance of a single PCM type (either RT-35or RT-27) with a combination of multiple PCMs (RT-35-RT27). Further, we evaluated various thickness combinations of the multi-PCM configuration (RT-35-RT27), including 2.5mm–7.5mm, 5 mm–5 mm, and 7.5 mm–2.5 mm, to identify the best-performing setup. Over the course of a day, the multi-PCM setup (RT-35-RT27) maintains a consistently lower average interior wall temperature than using a single PCM. Among the configurations tested, the 5 mm–5 mm multi-PCM setup (RT-35-RT27) emerged as the most effective, displaying steadier results than the other variations. Compared to a standard single glass pane, the proposed PV-PCM window reduced the highest interior wall temperature by up to 46 % when employing multiple PCMs. As a result, we advocate for the adoption of this innovative sliding window in future building designs.

Harnessing Nanomaterials for Enhanced Energy Efficiency in Transpired Solar Collectors: A Review of Their Integration in Phase-Change Materials

The building sector plays an important role in the global climate change mitigation objectives. The reduction of CO2 emissions and energy consumption in the building sector has been intensively investigated in the last decades, with solar thermal energy considered to be one of the most promising solutions due to its abundance and accessibility. However, the discontinuity of solar energy has led to the study of thermal energy storage to improve the thermal performance of solar thermal systems. In this review paper, the integration of various types of phase-change materials (PCMs) in transpired solar collectors (TSC) is reviewed and discussed, with an emphasis on heat transfer enhancements, including nanomaterials. Thermal energy storage applied to TSC is studied in terms of design criteria, materials technologies, and its impact on thermal conductivity. This review highlights the potential of nanomaterial technology integration in terms of thermal performance improvements. The utilization of nanomaterials in solar walls holds the potential to significantly enhance their performance. The integration of diverse materials such as graphene, graphite, metal oxides, and carbon nanoparticles can pave the way for improving thermal conductivity.

Synthesis and properties of biomass derived carbon/PEG composite as photothermal conversion effective phase change material for functional concrete

Mixing phase change material (PCM) into concrete is a practical strategy for functionalizing concrete as an energy-storage unit. This study aims to invent an efficient photo-thermal conversion type PCM for the manufacturing energy storage functional concrete, which meet the needs of hydration heat storage and thermal storage in service. To solve the liquid leakage problem of PCM, a novel bamboo-based hydrothermal carbon sphere (HCS) with unique mesoporous structure was prepared to pack polyethylene glycol (PEG) to make shape stable PCM. The photo-thermal material nano-Ag was successfully introduced into the composite PCM through a high-voltage electrostatic field. To understand the stability and performance of the PCM for concrete use, the structural composition and thermal storage efficiency of Ag@HCS-CNTs/PEG in simulated concrete pore solution (a highly alkaline solution containing potassium, sodium, and calcium cations) were systematically studied via multiple characterization methods. After being soaked in concrete pore solution for 7 days, the PCM shows outstanding thermal storage density (147 J/g), photo-thermal conversion efficiency (110.6%), and resistance to Na+, Mg2+, Cl− and SO42−. In addition, the biomass subtracted PCM preparation has low energy consumption and low carbon emission features. These open a window of realistic PCM application in the structural concrete, insulation porous walls and energy storage buildings.

Experimental investigation on the use of PCM heat exchangers in Geo-energy piles and walls

The current paper aims to experimentally investigate the thermal performance of geo-energy piles and walls fabricated with Phase Change heat exchangers. Four prototype concrete geo-energy structures (i.e., piles and walls) were tested using two distinct types of heat exchangers, including standard heat exchangers and PCM heat exchangers. The PCM heat exchangers utilized in the current study were filled up with two different types of Phase Change Materials (PCM) with melting points of 26 °C and 42 °C for geo-energy piles and walls, respectively. The thermal efficiency of the geo-energy piles/walls was experimentally assessed over 100 h of continuous operation under cycles of cooling and heating. The findings illustrated that using PCM heat exchangers led to enhancing the heat transfer efficiency of geo-energy piles by 75 % and 43 % in heating and cooling operations, respectively, compared to those achieved using a standard heat exchanger. Furthermore, the heat transfer performance of geo-energy walls with a PCM heat exchanger was enhanced by 43 % and 32 % in heating and cooling tests, respectively, compared to those achieved using a standard heat exchanger. Moreover, the findings indicated that the inclusion of PCM heat exchangers in geo-energy structures contributed to reducing: the impact on soil temperature and thermal interference radius as well as the potential structural damage due to thermal stress.

Effect of Dry Ice Gel PCM on Wall Freezer Temperature Variance

The increasing population growth in cities will cause environmental detriments such as global warming and ozone depletion. The electricity need will increase in the future due to the higher temperature in the cities, leading to the higher usage of cooling equipment such as freezers. The current study proposed a method to improve the freezer's energy efficiency by using phase change material of dry ice gel. Most of previous studies only focused on the impact of position of phase change materials on the temperature of wall freezer while no previous studies consider the detailed methodology of measurement and the impact of phase change material based on dry ice gel to the variance of wall temperature. The sensor thermocouple type T and data logger ADAM 6018+ were used to measure the wall temperature of the freezer. The results showed that the sensor thermocouple was verified to the calibrated thermometer with R2 = 0.99. The installation of phase change material based on dry ice gel on the wall freezer could maintain the temperature around 1-2oC while the freezer was turned off for 4, 6, and 8 hours. The efficiency of freezer could be increased from 10% to 30% due to using dry ice gel phase change material. The future study should investigate the various types of phase change materials and the new combination of phase change materials.

Mathematical model of the solar combined cycle power plant using phase change materials in thermal energy storage system (Thermodynamic analysis)

This research presents a novel mathematical framework for optimizing solar combined cycle power plants, with a particular emphasis on the exergy analysis of various superheating heat exchanger configurations used in thermal energy storage. The importance of phase change materials (PCMs) in improving the thermodynamic efficiency of solar combined cycle power plants is emphasized in this study. The investigation includes three configurations, two with a single PCM and one with two PCMs. The use of PCMs is intended to increase storage density, reduce volume, and maintain consistent temperatures, thereby favoring latent energy storage. The model developed evaluates exergy efficiency and output temperature profiles during the charging and discharging processes. The results show that the single PCM configuration has an impressive charging efficiency of 93.12 %, reaching an output temperature of 371 °C in 8 h. The two PCM configurations, on the other hand, achieve even higher efficiency at 94.89 % during charging, with an output temperature of 367 °C over a slightly longer 10-hour period. This comparison emphasizes the benefits of using two PCMs, demonstrating increased exergy efficiency and a marginal increase in output temperature over a single PCM setup. Furthermore, a comparison of the outcomes resulting from the use of a single type of PCM in exchangers reveals that the disparity in PCM melting temperatures causes only minor variations in the system's efficiency. The findings emphasize the significance of optimal PCM utilization for efficient solar energy retention, particularly during periods of low radiation.

Shell-Driven Localized Oxide Nanoparticles Determine the Thermal Stability of Microencapsulated Phase Change Material.

Not all encapsulation techniques are universally apt for every type of phase change material (PCM), highlighting the imperative for methodological precision. This study addresses the challenges of microencapsulated PCM (MEPCM) arising from the immiscible pairing of α-Al2O3 nanoparticles with Sn microparticles. The high-speed impact blending (HIB) dry synthesis technique is employed, facilitating large-volume production of Sn@α-Al2O3 MEPCMs. The resulting MEPCMs not only seamlessly endure 100 cycles of melting-solidification but also, with the strategic incorporation of a glass frit, exhibit remarkable thermal durability, withstanding up to 1000 melting-solidification cycles. Even under ultrafast thermal fluctuations, the α-Al2O3 shell remained resilient through 100 cycles. A marked reduction in supercooling is observed, which is attributed to the formation of SnO and SnO2 nanoparticles within the α-Al2O3 crystal lattice. The atomically resolved interface dynamics between SnO2 and α-Al2O3 play a pivotal role, lowering the energy barrier for Sn nuclei formation during solidification. This affects the accelerated Sn nucleation rate, effectively suppressing supercooling. Such insights offer a deeper understanding of the interplay between nanoscale crystal lattice imperfections and their implications for energy storage applications.

Accelerated charging dynamics in shell-and-multi-tube latent heat storage systems for building applications

Thermal energy storage (TES) is an emerging technique to store the surplus energy generated during periods of excess supply and utilise it when demand arises. Phase change material (PCM) stands out as a highly efficient TES system. Enhancing heat transfer during phase change is a major challenge in creating effective PCM-based TES systems. This study focuses on enhancing the melting performance of a shell-and-tube latent heat thermal energy storage (LHTES) system. This improvement is achieved by conducting an extensive parametric study involving various geometric factors including tube position from the bottom, vertical tube spacing, tube diameter, different heat exchanger shell aspect ratios, PCM temperature, tube temperature, and PCM type. A three-dimensional model is simplified to a two-dimensional geometry for numerical simulation. The results indicate that the PCM melting time decreased by 20.6 % and 4.4 % with a 20 mm vertical tube distance compared to 15 mm and 25 mm. Among the considered scenarios, the configuration with a doubled number of tubes in width consistently exhibits a higher melt fraction throughout the entire duration. Regarding the aspect ratio, the square-shaped system demonstrates both quicker melting times and a higher energy storage rate. When comparing PCM types, it is evident that RT 35 exhibits a 3.2 % higher heat storage rate and a 44.7 % shorter melting time compared to RT 35 HC.

Enhancing performance of solar stills ‐ A review

AbstractSolar stills can be an easy and environmentally viable solution in today's world, where a lack of fresh water sources is a major challenge. Solar stills, on the other hand, aren't economically viable due to their poor efficiency. It has been the subject of several studies to improve its efficiency and output. The goal of this review article is to understand and summarize recent studies conducted to improve the efficiency and commercial viability of solar stills. It focuses on using experimental and numerical techniques to manipulate different parameters that affect freshwater production in stills in order to arrive at a suitable condition where the efficiency and productivity of the solar still are maximized. Effects of modifications such as addition of baffles, fans, fins, phase change material (PCM), etc., and its consequent influence on freshwater production rate are presented in this article. Fins, for example, improved the efficiency of solar still by about 40% and productivity by about 16%. PCMs too increased the productivity rate by around 50%–90% depending on the type of PCM used. Baffles were found to be more effective when they were mounted closer to the front wall of the solar still. The findings and conclusions of all the studies are summarized. This review article aims to provide an overview of solar stills and the various modifications that may be done to improve their overall efficiency.

Faz Değiştiren Malzemelerin Isı Değiştiricisi Performansına Etkisinin, Farklı Parametreler İçin İncelenmesi

Technological improvements and increasing energy demand necessitate energy efficient designs for heat transfer systems. The storage and reuse of heat energy plays an important role in the development of energy-efficient systems. Phase change materials (PCMs) are crucial components which increase energy efficiency in heat exchangers as can be applied to many systems. In this study, the heat transfer performance of different types of phase change materials in a regenerative heat exchanger was investigated according to different parameters. Reynolds number depending on the hot fluid velocity (Re=400, 800, 1200, 1600), hot fluid inlet temperature (Tsıcak,giriş=40, 60, 70, 80℃), and different types of phase change materials (RT60, RT100, and SP70) are the parameters used in this study. ANSYS Fluent software was used for computational fluid dynamics analysis. As a result, it has been determined that when the Reynolds number of the hot fluid in the heat exchanger was increased in the range of Re=400-1600, the heat transfer effectiveness increase of 17%; when the hot fluid inlet temperature was increased in the range of Thot,inlet=40-80℃, the heat transfer effectiveness increase of 21%. As regards the effect of different types of phase change materials, the heat transfer effectiveness was 81% for RT60, 79% for SP70 and 76% for RT100. It has been evaluated that, with the results obtained from this study, heat exchangers with higher heat transfer effectiveness and higher energy storage capacity can be designed.

Hybrid (Optimal) Selection Model for Phase Change Materials Used in the Cold Energy Storage of Air Conditioning Systems

The latent heat storage of phase change materials (PCMs) can be used in refrigeration and air conditioning systems. Storing cool energy during the nighttime (off-peak hours) and releasing the cool energy during the daytime (on-peak hours) to reduce the number of starts of the chiller and pumps is a practical approach for achieving energy saving and carbon reduction. Therefore, selecting PCMs is vital for improving energy efficiency and preventing future energy shortages. However, selecting PCMs is complicated by their unique characteristics and types. The purpose of this study was to establish a PCM selection model by combining the Delphi, analytic hierarchy process (AHP), and VIseKriterijumska Optimizacija I Kompromisno Resenje (VIKOR) methods to select the optimal PCM type applied in cold storage. A numerical example was used to verify the model’s usability, confirming that A9 is the optimal PCM for the cold storage of an air conditioning system. This three-stage PCM selection model combining the Delphi, AHP, and VIKOR approaches provides a more suitable selection model and considers the selection method of material criteria. Moreover, it can solve the problem of difficult PCM selection. Simultaneously, it considers mechanisms to incorporate a company’s primary considerations into material selection for real-world applications. These results can facilitate material evaluation and selection during system design and material qualification, helping companies achieve the goals of energy saving, carbon reduction, and sustainable management in the future.

An in-situ growth Fe3O4 and polyaniline on carbon cloth encapsulated composite phase change materials with high thermal conductivity and photothermal energy conversion and storage

Phase change materials (PCMs) play a crucial role in thermal management and solar energy utilization. However, PCMs suffer from low thermal conductivity, tend to leak during the phase change process, and do not possess photothermal conversion properties, limiting their application in these fields. In this work, thermally conductive enhanced composite PCMs with photothermal conversion are fabricated by encapsulating polyethylene glycol (PEG) into Fe3O4 and polyaniline (PANI) decorated carbon cloth (CC). The prepared PEG@PFCC composite PCMs exhibited high heat storage density (132.06–137.25 J/g), significantly improved leakage-proof properties, and excellent thermal and cyclic stability. Meanwhile, the continuous double-coating of PANI and Fe3O4 not only gives the composite PCMs superb thermal conductivity (thermal conductivity of 1.61 W/m·K, 416 % higher than that of the pristine PEG), but also high photothermal conversion efficiency (91.5 %) and excellent electromagnetic interference (EMI) shielding (up to 38 dB), which broaden the composite PCMs' adaptability of applications. In summary, this innovative type of carbon cloth-based composite PCMs provide a creative path for the design and development of energy storage and conversion materials, which exhibit tremendous potential in the applications of electronic protection, infrared stealth, thermal management of wearable devices, and solar thermal energy utilization.

Thermal Management and Electrical Efficiency for Concentrator Photovoltaic Systems Using Multiple Phase Change Materials

The performance of solar panels in generating electrical energy is closely tied to the effectiveness of the employed cooling system. While the utilization of phase change materials (PCMs) as latent thermal units as a cooling system has been suggested for recovering solar panels’ heat, research focusing on a comprehensive comparison of various PCMs for this purpose has been lacking. To address this gap, our study aims to provide a thorough comparative analysis of three distinct PCMs: Gallium, Paraffin RT35HC and CaCl2.6H2O. The objective is to determine the most efficient PCM for cooling solar panels. Using Fluent-Ansys-based numerical simulations, our study investigates the transient (unsteady) thermal exchange between PCMs and a solar panel. The research examines various PCM types housed in a container behind the solar panel, while also assessing the impact of inclination angles (0° to 90°) on thermal and electrical efficiency. Our results highlight Gallium's superior cooling performance and sustained high electrical efficiency. Conversely, CaCl2.6H2O leads to decreased electrical efficiency (less cooling performance), while RT35HC shows potential at extreme angles with a slight efficiency decline (∼10.2%). By offering a comprehensive comparative assessment of diverse PCMs and considering the influence of inclination angles, our study contributes valuable insights to optimizing solar panel cooling systems and enhancing overall energy generation efficiency.