Two-dimensional Reversed-phase Research Articles

Purification of saponins from leaves of Panax notoginseng using preparative two-dimensional reversed-phase liquid chromatography/hydrophilic interaction chromatography

Saponins are widely distributed in the plant kingdom and have been shown to be active components of many medicinal herbs. In this study, a two-dimensional purification method based on reversed-phase liquid chromatography coupled with hydrophilic interaction liquid chromatography was successfully applied to purify saponins from leaves of Panax notoginseng. Nine saponin reference standards were used to test the separation modes and columns. The standards could not be resolved using C18 columns owing to their limited polar selectivity. However, they were completely separated on a XAmide column in hydrophilic interaction liquid chromatography mode, including two pairs of standards that were coeluted on a C18 column. The elution order of the standards on the two columns was sufficiently different, with a correlation coefficient between retention times on the C18 and XAmide columns of 0.0126, indicating good column orthogonality. Therefore, the first-dimension preparation was performed on a C18 column, followed by a XAmide column that was used to separate the fractions in the second dimension. Fifty-four fractions were prepared in the first dimension, with 25 fractions rich in saponins. Eight saponins, including two pairs of isomeric saponins and one new saponin, were isolated and identified from three representative fractions. This procedure was shown to be an effective approach for the preparative isolation and purification of saponins from leaves of P. notoginseng. Moreover, this method could possibly be employed in the purification of low-content and novel active saponins from natural products.

Columns and optimum gradient conditions for fast second‐dimension separations in comprehensive two‐dimensional liquid chromatography

Gradient elution provides significantly higher peak capacity in comparison to the isocratic elution mode, hence it is very useful in online comprehensive two-dimensional liquid chromatography (LC). We compared suitability of five commercial core-shell columns and one monolithic column for fast gradients in the second LC dimension, where the time of separation is strictly limited by the fraction cycle time. In two-dimensional reversed-phase systems with partially correlated retention, the resolution, the peak capacity, and the regularity of coverage of the second-dimension retention space can be improved by appropriate adjusting the gradient time and the gradient range to suit the sample properties. We developed a new strategy for adjusting the gradient mobile phase composition range in the second-dimension, employing the retention data of representative sample standards characterizing the sample properties, which can be calibrated using the reference alkylbenzene series. Optimized second-dimension gradients with single-step or segmented profiles covering two or more fraction ranges, employed for the separation of subsequent fractions from the first-dimension, improve significantly the resolution, the separation time, and the regularity of coverage of the two-dimensional retention plane. The approach was applied to the two-dimensional comprehensive separation of phenolic acids and flavonoid compounds occurring as natural antioxidants.

Comprehensive characterization of Stevia Rebaudiana using two‐dimensional reversed‐phase liquid chromatography/hydrophilic interaction liquid chromatography

Two-dimensional reversed-phase liquid chromatography/hydrophilic interaction liquid chromatography (2D-RPLC/HILIC) system was successfully applied for comprehensive characterization of steviol glycosides from Stevia rebaudiana. The experiments were performed in offline mode using an XCharge C18 column in first dimension and an XAmide column in second dimension. In first dimension, preliminary separation of Stevia aqueous extract was accomplished and 30 fractions were collected. Then fractions 1-20 were selected for further purification and 13 compounds with high purity were obtained in second dimension. Comprehensive characterization of these compounds was completed by determination of their retention time, accurate molecular weight, diagnostic fragmentation ions, and nuclear magnetic resonance spectroscopy. As a result, all nine known steviol glycosides, as well as other four steviol glycosides were fully purified. The result demonstrated that this procedure is an effective approach for the preparative separation and comprehensive characterization of steviol glycosides in Stevia. This 2D-RPLC/HILIC method will be a promising tool for the purification of low-abundance compounds from natural products.

Comprehensive impurity profiling of nutritional infusion solutions by multidimensional off-line reversed-phase liquid chromatography × hydrophilic interaction chromatography–ion trap mass-spectrometry and charged aerosol detection with universal calibration

A new analysis strategy was employed for the establishment of a comprehensive qualitative and quantitative impurity profile of a stressed multi-constituent pharmaceutical drug formulation, namely a nutritional infusion solution composed of amino acids and dipeptides. To deal with the highly complex samples a multidimensional analysis approach was developed which made use of an off-line two-dimensional reversed-phase liquid chromatography (RPLC)×hydrophilic interaction chromatography (HILIC) separation and combination of complementary detection involving ion trap mass spectrometry (IT-MS) and a charged aerosol detector (CAD). The CAD is a mass-sensitive universal detector for non-volatile compounds with relatively consistent detector response. A universal calibration function was set up with a set of standards. This universal calibration function was then employed to quantify unknown impurities allowing their classification into those that need to be reported (>0.05% relative to the precursor compound), identified (>0.1%), and quantified (>0.15%). The dilemma of unavailability of authentic standards at this stage of research for quantification could thereby be circumvented. Relevant impurities above the reporting threshold were identified by IT-MS. Impurities detected comprised di-, tri- and tetrapeptides, cyclic dipeptides (diketopiperazines), pyroglutamic acid derivatives and their condensation products. Cross-validation with HPLC–MS/MS methods using synthesized authentic standards confirmed the results obtained by the presented multidimensional analysis assay.

Monolithic integration of two-dimensional liquid chromatography-capillary electrophoresis and electrospray ionization on a microfluidic device.

A microfluidic device capable of two-dimensional reversed-phase liquid chromatography-capillary electrophoresis with integrated electrospray ionization (LC-CE-ESI) for mass spectrometry (MS)-based proteomic applications is described. Traditional instrumentation was used for the LC sample injection and delivery of the LC mobile phase. The glass microfabricated device incorporated a sample-trapping region and an LC channel packed with reversed-phase particles. Rapid electrokinetic injections of the LC effluent into the CE dimension were performed at a cross-channel intersection. The CE separation channel terminated at a corner of the square device, which functioned as an integrated electrospray tip. In addition to LC-CE-ESI, this device was used for LC-ESI without any instrumental modifications. To evaluate the system, LC-MS and LC-CE-MS analyses of protein digests were performed and compared.

Determination of rat plasma levels of sertraline enantiomers using direct injection with achiral–chiral column switching by LC–ESI/MS/MS

A highly sensitive and selective on-line two-dimensional reversed-phase liquid chromatography/electrospray ionization–tandem mass spectrometric (2D-LC–ESI/MS/MS) method to determine sertraline (SRT) enantiomers in rat plasma was developed and validated. The method was applied to separate and determine the diastereomers and enantiomers of SRT simultaneously. The 2D-LC–ESI/MS/MS system consisted of RAM column in first dimension for trapping proteineous part of plasma and a chiral Cyclobond column as second dimension for separation of enantiomers and diastereomers of SRT using 0.1% aqueous trifluoroacetic acid:acetonitrile (86:14, v/v) as mobile phase in an isocratic elution mode. The linear dynamic range was 0.5–200 ng/mL ( r 2 > 0.999). Acceptable precision and accuracy were obtained over the calibration range. The assay was successfully used in the analysis of SRT enantiomers in rat plasma to support pharmacokinetic studies.

Two-dimensional LC–MS/MS determination of antiretroviral drugs in rat serum and urine

A simple, rapid, reliable and highly sensitive on-line two-dimensional reversed-phase liquid chromatography–tandem mass spectrometric (2D-LC/MS/MS) method to determine antiretroviral drugs viz., abacavir (ABC), nevirapine (NVP) and indinavir (IDV) in rat serum and urine was developed and validated. The analytes were extracted on-line from rat serum and urine by a restricted access material (RAM) column and back-flushed into the reversed-phase C 18 column for separation by LC. Detection was carried out by ESI-MS/MS. The developed method showed good selectivity, accuracy and precision for quantification of the antiretroviral drugs in rat serum and urine. Quantification limits for abacavir and nevirapine were 4.0 ng ml −1, whereas for indinavir 4.7 ng ml −1. The calibration graphs were linear in the range of 4–50 ng ml −1for abacavir, nevirapine and indinavir. The method was successfully applied to study the pharmacokinetics of antiretroviral in rats.

On‐line 2D‐LC‐ESI/MS/MS determination of rifaximin in rat serum

A highly sensitive and selective on-line two-dimensional reversed-phase liquid chromatography/electrospray ionization-tandem mass spectrometry (2D-LC-ESI/MS/MS) method was developed and validated to determine rifaximin in rat serum by direct injection. The 2D-LC-ESI/MS/MS system consisted of a restricted access media column for trapping proteins as the first dimension and a Waters C(18 )column as second dimension using 0.1% aqueous acetic acid:acetonitrile as mobile phase in a gradient elution mode. Rifampacin was used as an internal standard. The linear dynamic range was 0.5-10 ng/mL (r(2) > 0.998). Acceptable precision and accuracy were obtained over the calibration range. The assay was successfully used in analysis of rat serum to support pharmacokinetic studies.

Development of novel fiber-packed needle interface for off-line reversed-phase liquid chromatography–capillary gas chromatography

For two-dimensional reversed-phase liquid chromatography–gas chromatography (2D RPLC–GC), a specially-designed needle packed with a polymer-coated fibrous stationary phase was introduced as a novel interface. The bundle of synthetic fibers coated with polydimethylsiloxane (PDMS) was packed into the head section of the needle, and served as the extraction medium. Using the post-column dilution of the LC eluent by water and subsequent extraction with the needle interface, the analyte was successfully concentrated to the PDMS phase on the fibrous support in the needle. The concentrated analytes were directly injected to GC system by inserting the needle to a heated GC injector. 2D separations of aliphatic and aromatic hydrocarbons, and also kerosene-extract were performed with the off-line RPLC–GC system interfaced by the needle extractor. The results suggested that the fiber-packed needle interface could be one of the simple and effective approaches to develop an on-line coupled LC–GC system.

Characterization of polymethoxylated flavones in Fructus aurantii by off-line two-dimensional liquid chromatography/electrospray ionization-ion trap mass spectrometry

Off-line two-dimensional reversed-phase liquid chromatography (2D-RPLC) coupled to electrospray ionization-ion trap mass spectrometry (ESI-ITMS) was operated in positive mode (PI) to characterize polymethoxylated flavonoids (PMFs) in botanical sample. The fragments of [M+H− n×15] + produced by loss of one or more methyl group from the protonated molecules, as well as [M+H−14] +, [M+H−29] +, [M+H−33] +, [M+H−43] +, [M+H−46] + and [M+H−61] + fragments formed the multiple MS (MS n ) “fingerprint” of PMFs. 42 target compounds were tentatively identified from the extract of Fructus aurantii ( F. aurantii) based on this “fingerprint” . Experimental outcomes indicated that the application of 2D separation method can reduce the matrix suppression of analytes caused by the coelution with interferential components and the column overloading of interferential components. 42 versus 23 target compounds were detected through 2D versus 1D method, which confirm the superiority of 2D coupled to MS in elimination of matrix effects.

Novel two-dimensional reversed-phase liquid chromatography/hydrophilic interaction chromatography, an excellent orthogonal system for practical analysis

A novel two-dimensional reversed-phase liquid chromatography/hydrophilic interaction chromatography (2D-RPLC/HILIC) system is developed with the introduction of the click β-cyclodextrin (β-CD) stationary phase. The offline system shows excellent abilities for the separation of polar and medium-polarity components in traditional Chinese medicine (TCM). It facilitates us not only to separate components that cannot be resolved by uni-dimensional chromatography, but also to achieve much more efficient detection of components with low abundance. The orthogonality of this new system is excellent. A simple geometric approach is developed to characterize the practical orthogonality of 2D-LC in the analysis of complex unknown samples. The mathematical characterization results are in good accordance with the experimental findings, and both demonstrate that the proposed 2D-RPLC/HILIC system is a powerful tool for the separation of polar and medium-polarity complex samples. This system may have a great potential for the separation of peptides and metabolomic compounds with similar polarity.

Ultra sensitive determination of limaprost, a prostaglandin E 1 analogue, in human plasma using on-line two-dimensional reversed-phase liquid chromatography–tandem mass spectrometry

A highly sensitive and selective method has been developed and validated to determine limaprost, a prostaglandin (PG) E 1 analogue, in human plasma by on-line two-dimensional reversed-phase liquid chromatography–tandem mass spectrometry (2D-LC/MS/MS) due to the lack of efficient methods to determine very low levels of limaprost in plasma. Limaprost and its deuterium derivatives, used as internal standard, were extracted by protein precipitation and following three-step solid phase extractions. After extraction procedure, samples were analyzed by on-line 2D-LC/MS/MS with electrospray ionization in negative mode. The 2D-LC system consists of Phenyl column at first dimension and ODS at second dimension with a trapping column placed between the separation columns. The linear dynamic range of this method was 0.1–10 pg/ml with 3 ml of plasma ( r > 0.9987). Acceptable precision and accuracy were obtained over the calibration curve ranges. The assay has been successfully used in analyses of human plasma samples to support clinical pharmacokinetics studies.

We-P11:137 Relationships between insulin resistance, obesity and dyslipidemia with ambulatory blood pressure monitoring in an urban argentine population

A simple, rapid, reliable and highly sensitive on-line two-dimensional reversed-phase liquid chromatography–tandem mass spectrometric (2D-LC/MS/MS) method to determine antiretroviral drugs viz., abacavir (ABC), nevirapine (NVP) and indinavir (IDV) in rat serum and urine was developed and validated. The analytes were extracted on-line from rat serum and urine by a restricted access material (RAM) column and back-flushed into the reversed-phase C18 column for separation by LC. Detection was carried out by ESI-MS/MS. The developed method showed good selectivity, accuracy and precision for quantification of the antiretroviral drugs in rat serum and urine. Quantification limits for abacavir and nevirapine were 4.0 ng ml−1, whereas for indinavir 4.7 ng ml−1. The calibration graphs were linear in the range of 4–50 ng ml−1for abacavir, nevirapine and indinavir. The method was successfully applied to study the pharmacokinetics of antiretroviral in rats.

Phase system selectivity and two-dimensional separations in liquid column chromatography

Correlations between the separation selectivity in aqueous and non-aqueous reversed-phase systems and in normal-phase LC systems were investigated for samples containing different numbers of two repeat structural elements. Such samples are best separated in “orthogonal” two-dimensional chromatographic systems, showing selectivity for one type of the repeat structural element only in the first dimension and for the other structural element only in the second dimension. The number of resolved compounds improves as the degree of orthogonality of the separation systems increases with decreasing correlation between the selectivities for the sample structural distribution in the two dimensions. Orthogonal systems with non-correlated selectivities for each repeat structural element provide the highest number of separated peaks and regular arrangement of the peaks over the two-dimensional retention space according to the individual structural element distribution and the best use of the available peak capacity. Fully orthogonal systems are difficult to find in practice. Partially orthogonal system with correlated selectivities for one structural type distribution, but with one system non-distinguishing the distribution for the other structural element are still useful for the two-dimensional separations. The correlations between the selectivities for repeat regular structural increments were employed to evaluate the suitability of phase systems for two-dimensional HPLC separations. The selectivity correlation in various reversed-phase and normal-phase systems was evaluated for two sample types: (1) Various RP columns show significantly inversely correlated selectivities for acyl lengths and numbers of double bonds distribution, but the differences in the double bond selectivity can be used for practical separations of triacylglycerols with the same equivalent carbon numbers. (2) Synthetic EO–PO block (co)oligomers with two-dimensional distribution of oxyethylene and oxypropylene monomer units were separated according to the two distribution types using on-line two-dimensional reversed-phase–normal-phase LC with a C18 column in the first dimension and an aminopropyl silica column in the second dimension.

Fully automated online multi-dimensional protein profiling system for complex mixtures

For high throughput proteome analysis of highly complex protein mixtures, we have constructed a fully automated online system for multi-dimensional protein profiling, which utilizes a combination of two-dimensional liquid chromatography and tandem mass spectrometry (2D-LC–MS–MS), based on our well-established offline system described previously [K. Fujii, T. Nakano, T. Kawamura, F. Usui, Y. Bando, R. Wang, T. Nishimura, J. Proteome Res. 3 (2004) 712]. A two-valve switching system on a programmable auto sample injector is utilized for online two-dimensional chromatography with strong cation-exchange (SCX) and reversed-phase (RP) separations. The SCX separation is carried out during the equilibration of RP chromatography and the entire sequence of analysis was performed under fully automated conditions within 4 h, based on six SCX fractionations, and 40 min running time for the two-dimensional RP chromatography. In order to evaluate its performance in the detection and identification of proteins, digests of six standard proteins and yeast 20S proteasome have been analyzed and their results were compared to those obtained by the one-dimensional reversed-phase chromatography system (1D-LC–MS–MS). The 2D-LC–MS–MS system demonstrated that both the number of peptide fragments detected and the protein coverage had more than doubled. Furthermore, this multi-dimensional protein profiling system was also applied to the human 26S proteasome, which is one of the highly complex protein mixtures. Consequently, 723 peptide fragments were identified as 31 proteasome components, together with other coexisting proteins in the sample. The identification could be comprehensively performed with a 63% sequence coverage on an average, and additionally, with modifications at the N-terminus. These results indicated that the online 2D-LC–MS–MS system being described here is capable of analyzing highly complex protein mixtures in a high throughput manner, and that it would be applicable to dynamic proteomics.

Comprehensive two-dimensional separations of complex mixtures using reversed-phase reversed-phase liquid chromatography

A comprehensive two-dimensional reversed-phase reversed-phase liquid chromatographic system for the separation of a complex mixture of oligostyrenes was developed using results from a previous theoretical assessment of the informational similarity, percent synentropy, orthogonality and peak capacity of hypothetically coupled systems. The degree of sample attribute order in the first separation dimension was also used in the development of the experimental two-dimensional system. A C18(methanol)/CCZ(acetonitrile) two-dimensional system was chosen for the comprehensive analysis of the oligostyrene mixtures because this system had the lowest solute crowding, highest orthogonality and was observed to have order with respect to a sample attribute in the first separation dimension. The separations achieved were in full agreement with the results from information theory and (a geometric approach to) factor analysis assessments. High sampling rates in the first liquid chromatographic dimension were shown to be impossible or inefficient when the peak capacity and separation time of the second dimension was high or when the aim of the exercise was to isolate individual sample constituents in high yield.

Comprehensive two-dimensional separations of complex mixtures using reversed-phase reversed-phase liquid chromatography

A comprehensive two-dimensional reversed-phase reversed-phase liquid chromatographic system for the separation of a complex mixture of oligostyrenes was developed using results from a previous theoretical assessment of the informational similarity, percent synentropy, orthogonality and peak capacity of hypothetically coupled systems. The degree of sample attribute order in the first separation dimension was also used in the development of the experimental two-dimensional system. A C18(methanol)/CCZ(acetonitrile) two-dimensional system was chosen for the comprehensive analysis of the oligostyrene mixtures because this system had the lowest solute crowding, highest orthogonality and was observed to have order with respect to a sample attribute in the first separation dimension. The separations achieved were in full agreement with the results from information theory and (a geometric approach to) factor analysis assessments. High sampling rates in the first liquid chromatographic dimension were shown to be impossible or inefficient when the peak capacity and separation time of the second dimension was high or when the aim of the exercise was to isolate individual sample constituents in high yield.

Simple and comprehensive two-dimensional reversed-phase HPLC using monolithic silica columns.

Simple and comprehensive two-dimensional (2D)-HPLC was studied in a reversed-phase mode using monolithic silica columns for second-dimension (2nd-D) separation. Every fraction from the first column, 15 cm long (4.6-mm i.d.), packed with fluoroalkylsilyl-bonded (FR) silica particles, was subjected to the separation in the 2nd-D using one or two octadecylsilylated (C(18)) monolithic silica columns (4.6-mm i.d., 3 cm). Monolithic silica columns in the 2nd-D were eluted at a flow rate of up to 10 mL/min with separation time of 30 s that meets the fractionation every 15-30 s at the first dimension (1st-D) operated at a flow rate of 0.4-0.8 mL/min. Three cases were studied. (1) In the simplest scheme of 2D-HPLC, effluent of the 1st-D was directly loaded into an injector loop of 2nd-D HPLC for 28 s, and 2 s was allowed for injection. (2) Two six-port valves each having a sample loop were used to hold the effluent of the 1st-D alternately for 30 s for one 2nd-D column to effect comprehensive 2D-HPLC without the loss of 1st-D effluent. (3) Two monolithic silica columns were used for 2nd-D by using a switching valve and two sets of 2nd-D chromatographs separating each fraction of the 1st-D effluent with the two 2nd-D columns alternately. In this case, two columns of the same stationary phase (C(18)) or different phases, C(18) and (pentabromobenzyloxy)propylsilyl-bonded (PBB), could be employed at the 2nd-D, although the latter needed two complementary runs. The systems produced peak capacity of approximately 1000 in approximately 60 min in cases 1 and 2 and in approximately 30 min in case 3. The three stationary phases, FR, C(18), and PBB, showed widely different selectivity from each other, making 2D separations possible. The simple and comprehensive 2D-HPLC utilizes the stability and high efficiency at high linear velocities of monolithic silica columns.

Evaluation of the two-dimensional reversed-phase–reversed-phase separations of low-molecular mass polystyrenes

The resolving power of four reversed-phase–reversed-phase two-dimensional (2D) chromatographic systems was evaluated using information theory (IT) and a geometric approach to factor analysis. The first separation dimension employed a C18 column, while the second separation dimension employed a carbon clad zirconia column. Mobile phases in each dimension were either methanol or acetonitrile. The sample matrix that was employed in this study contained a mixture of 58 components, comprised of stereoisomers and structural isomers of a systematic variation in molecular weight. Each of the components were oligostyrenes, with between two and five configurational repeating units having either n-butyl, sec-butyl or tert-butyl end groups. In the two-dimensional systems employed in this study, between 46 and 49 of the 58 components could be separated, depending on the mobile phase combinations—with apparent resolution that could not possibly be achieved in a single one-dimensional separation. The results from this study indicate that in order to fully evaluate the resolving power of a 2D system multiple methods of analysis that evaluate the separation potential are most appropriate. This becomes increasingly important when the sample contains components that are very closely related and the retention of solutes displays a high degree of solute crowding.

Two dimensional reversed-phase–reversed-phase separations: Isomeric separations incorporating C 18 and carbon clad zirconia stationary phases

Informational theory and a geometric approach to factor analysis were employed to evaluate the degree of orthogonality of a two-dimensional reversed-phase–reversed-phase chromatographic system. The system incorporated a C 18 column as one dimension and a carbon clad zirconia column as the second dimension. In order to study the resolving power of this system, the separation of a sample matrix containing an artificial mix of 32 isomers (structural and diastereoisomers) was evaluated. Using this system, between 25 and 28 of the 32 isomers could be separated, depending on the mobile phase combinations—with resolution that could not possibly be achieved in a single one dimensional separation. The results from this study indicate that in order to fully evaluate the resolving power of a 2D system multiple methods of analysis are most appropriate. This becomes increasingly important when the sample contains components that are very closely related and the retention of solutes is clustered in one quadrant of the 2D space. Ultimately, the usefulness of the 2D separation is determined by the goals of analyst.